Search Documents

By Takashi Goto

In 1968 three historical rockbursts had occurred at Bibai Coal Mine in Hokkaido. At the time they had been observed by several seismic observatories as natural earthquakes away more than 100km from Bibai City. These facts taught us that the occuerrence of failure yielded in underground opening that was accompanied with seismic wave could be observed by seismometer on the surface. After two years from this desaster, the study concerning to microseismic events generated from underground mining panels has been begun by researchers with heart-throb.

Jan 1, 1982

By R. Bhaskar

The results of an experimental study on the dispersion and deposition characteristics of fine coal dust in mine airways are presented. Experiments were conducted at various flow velocities using bituminous and semi-anthracite-coal dust which had a large proportion of dust in the respirable size range. Cross sectional variations in the concentration of dust at various points in the airway were also measured. Instruments used in the experiments included gravimetric samplers and impactors. Concentration measurements were made both for the respirable and total airborne dust. The experimental design, sampling procedures and results are discussed. The study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground mine airways.

Jan 1, 1986

A conventional paddle-type mixer and a gravity flow mixing device were evaluated for conditioning of phosphate ore with fatty acid and fuel oil, and for acid scrubbing prior to cationic flotation. Gravity flow mixing required less residence-time, but slightly higher reagent concentrations to achieve recovery levels similar to conventional conditioning. Grade was less sensitive to reagent concentration using the gravity flow mixer. For acid scrubbing, the gravity flow mixer proved equally effective. In this paper, the effect of time, pulp density, reagent concentration, and emulsification on conditioning and acid scrubbing efficiency of the two devices will be discussed.

Jan 1, 1987

By Brig M. Moudgil

It was reported earlier that francolite and dolomite from the South Florida deposits cannot be selectively floated using conventional conditioning with sodium oleate as the collector. However, dolomite could be separated from francolite if the minerals were first conditioned at pH 10 followed by reconditioning at a lower pH. An optimum separation was achieved at a reconditioning pH below 4.5. Reconditioning pH and collector concentration were determined to exert a major influence on the selectivity. Flotation, adsorption and transmission infrared spectroscopic results are presented to elucidate the mechanisms underlying the observed selectivity.

Jan 1, 1984

Adsorption experiments were conducted at two different solids loadings, to investigate the mechanism of oleate adsorption on apatite. Adsorption density at pH 10 was found to be dependent on solids loading in an oleate concentration region where surface precipitation could occur. Analysis of adsorption isotherms indicated three distinct regions of adsorption. In the region I (below the region of calcium oleate precipitation), molecular adsorption was observed. Simultaneous molecular adsorption and surface precipitation occurred in region II, while surface precipitation was predominant in region III along with some bulk precipitation. Correlation between flotation of apatite with sodium oleate and the mode of oleate interaction with the surface is established.

Jan 1, 1986

By C. A. Born

AMAX Inc. climax's mine-mill complex at Climax, Colorado is best known for its molybdenite production: 50,000 TPY of molybdenite flotation concentrate (95% MoS2) from mill heads containing 0.35% molybdenite. Less recognized are the byproducts that are concentrated from the tails generated in the rougher flotation circuit (see Figure 1). Climax recovers a heavy mineral concentrate by passing the rougher tailings from molybdenite flotation over Humphrey spirals (Figure 2a). This concentrate is floated using xanthate at pH 4 to remove sulfides, principally pyrite. The tails from the pyrite float are then cleaned of quartz, feldspar and light minerals by tabling (Figure 2b). Amine flotation follows at pH 1.5 and 75°C to float monazite (Figure 2c). The present circuit at Climax dries the monazite flotation tailings and utilizes high intensity cross-belt magnetic separation Figure 2d) to generate a high grade wolframite concentrate and a low-grade cassiterite product, both of which are contaminated with the mineral brannerite, (UO, TiO, UO2)TiO3. The uranium specifications have recently become difficult to meet due to the increasing percentage of brannerite reporting in the mill feed. A plant is being built utilizing hot sulfuric acid and sodium chlorate to leach this uranium from the monazite flotation tailings prior to their being fed to the wolframite- cassiterite magnetic separators. This modification is the subject of our paper.

Jan 1, 1975

By Mo Wanqiang

Equivalent-pressure ventilation is a method of balancing the air pressure between a productive face and its gob to extinguish fires and prevent the infiltration of toxic gases, so that the production of the face can be maintained. The method was successfully applied in Coal Mine No. 1 of Hebi Coal Mining Administration in north-central China. In this article, a practical application of the equivalent-pressure method to prevent carbon monoxide from entering an active longwall face adjacent to a fire breeding area is described, and four steps to achieve equivalent-pressure are discussed. The reliability of using this method and measures to maintain the equivalent-pressure are analyzed. It was observed that this method could maintain high production level while no sacrificing safety at the longwall face.

Jan 1, 1984

By W. Hu

Gravity concentration has been the main method for tin ore beneficiation, based on the significant difference of density between cassiterite and gangue in the tin ore. However, with the exhaustion of rich and coarse reserves, the proportion of tin distribution in slime be-comes as high as 50 to 70% and has a size range of -19 urn. In some sulfide tin ore, most of the tin is of the minus 10-urn size fraction, and thus slime processing has gained importance in tin ore processing. Some innovations are being developed, such as the centrifugal cone separator, belt concentrator, slime table, B-M separator, and slime flotation. Direct flotation with tolyl arsonic acid has been practiced with success.

Jan 1, 1989

By K. N. Santini

Natural zeolites are gaining recognition as an important commodity with an increasing number of industrial and consumer applications. This potential has prompted the Anaconda Minerals Company and other firms to investigate occurrences and markets for zeolites. The deposits of mordenite-rich tuff at Rome are of interest for their economic potential and for the excellent opportunity they provide to study a zeolite deposit formed in a hydrologically closed basin. Location The Rome property is located approximately 9 km west of Rome, Oregon, in Townships 31S. and 32S., Range 41E., Malheur County. It lies within the Owyhee Uplands of the northern Basin and Range physiographic province (Figure 1). The area discussed here includes a major portion of the depositional basin in which the zeolitic tuffs occur.

Jan 1, 1982

By R. T. Leigh

The continued decline In the production of synthetic soda ash (sodium carbonate) due to high costs and associated environmental factors, has improved the world demand for natural soda ash. The largest resource of natural soda ash is the mineable trona deposits of Southwestern Wyoming. Wyoming trona, a lacustrine evaporite of Eocene Age, is mined by five producers which process over 90% of the United States and 20% of the worlds soda ash. Total world consumption of soda ash is forecast to grow 1% annually. Increased expansion into foreign market's is absorbing the domestic overcapacity.

Jan 1, 1989

By Christopher D. Henry

Environmental geologic maps of the Wilcox and Jackson-Yegua lignite belts of the Texas Coastal Plain delineate land areas on the basis of their natural characteristics. Criteria used to define map units include substrate, soil, topography, geologic process, vegetation, and land use. The maps are useful in planning and reclamation of lignite mines and in meeting the requirements of State and Federal surface mining laws. Specific applications include identification of land capability, recharge areas and geometry of aquifers, flood-prone areas, areas that may qualify for prime farmland status, and other areas sensitive to lignite mining.

Jan 1, 1982

The height of permanent slopes at the Panguna mine of Bougainville Copper Limited will vary from 350 to 950 metres. A few degrees difference in slope angle has a large effect on the ore/waste stripping ratio. Optimum slopes can be achieved if longer batter slopes (exceeding 45m height) are excavated using bulldozers to trim parallel to controlling fracture surfaces. Unnecessary slope flattening by incorporating benches can cost millions of dollars in lost ore. Faults and other major weaknesses, which can result in wedge failure or erodible zones have been treated successfully with shotcrete, rockbolts and cable dowels. To minimize support effort and interference with mine production, early identification and treatment of unstable areas is important.

Jan 1, 1987

By J. A. M. Cano

A brief introduction is made on the existence of sulphides in the top gas of the Midrex Shaft Furnace, giving consideration to the operation of the furnace and the liberation of sulphur as well as its consequential effects on the reduction process. The text shows a study of sulphur distribution in the pellet, emphasizing the importance of this distribution in relation to the liberation of sulphur during the reduction. A study was made to determine the sulphur compounds that exist in the pellets, showing ways of controlling the sulphur distribution and reducing its liberation?during the reduction.

Jan 1, 1989

By Mark Alan Marlkos

Blebs of solid bitumen from the Magmont West orebody of the Viburnum Trend were examined and analyzed in an attempt to relate hydrocarbon distribution and origin to ore genesis. The bitumen was calculated to be approximately 48 to 63 percent aliphatic and is considered to be a polymerized normal crude oil. Polymerization, which was probably caused by water-washing, hardened the bleb surfaces and appears to have "frozen" the blebs during primary migration from local source beds. Comparison of the bitumen to kerogen in local shaly partings strongly Indicates that the oil was derived locally. The polymerized oil blebs are considered to have been derived from a type II (marine) kerogen. Textural analyses indicate that oil migration occurred after lead-zinc mineralization and at temperatures that exceed normal ancient or present geothermal gradients. The following sequence of events is postulated for the Magmont West orebody: 1 Generation of hydrogen sulfide during diagenesis of a normal organic-rich carbonate sequence. 2 Introduction of pulses of hot, metal-rich fluids that resulted in: a Lead-zinc mineralization by the following reaction: Me++ + H2S ? MeS + 2H+ b Solution of carbonates by excess acid produced during the above reaction. c Brecciation of host rock in some cases. 3 Passages of the pulse resulted in: a Carbonate buffering of fluid system to more alkaline conditions. b Precipitation of dolomite c Slight temperature drop. 4 Eventually the high temperatures Introduced by heated brine caused oil generation and initiated primary migration. 5 Water-washing and mild biodegradation altered the hydrocarbon blebs to their present composition.

Jan 1, 2013

By Ebelia Manda, Peter RK Chileshe, Sydney Chinyanta, Abdul Samson, Victor Mwango Bowa

Buttressing is a widely employed control measure for mitigating slope failure in various settings such as openpit mines, road sections, dams, and hilly or rocky terrains. This paper presents a study on the effects of buttressing, specifically concerning slide-head toppling failure. Drawing insights from a case study of slide-head toppling in Zambia, our investigation employs both analytical (limit equilibrium) and numerical (3DEC software) modeling techniques. The analytical and numerical models exhibit notable similarities in their schematics and overall results, revealing a subtle effect of buttressing in controlling slide-head toppling failure. This study contributes valuable insights into the nuanced role of buttressing in slope stability, with implications for optimizing buttress design parameters. While the overall findings suggest a modest influence of buttressing on slide-head toppling failure, further discussions delve into the specific implications and potential refinements for practical applications.

Jan 1, 2025

By John L. Halls

Modern business practice dictates that in order to ensure the economic optimization of investment, the size of any investment venture must be such that every increment of capital invested in such a venture yields at least a corporate minimum acceptable rate of return. This practice is based on the premise that alternative investment opportunities capable of yielding the minimum corporate return are immediately available. If a mining corporation is to make the maximum use of its investment funds, any capital investment in a mining property must comply with the above practice. The most important parameter in estimating ore reserves is the cut-off grade which is used to separate material into ore or waste. The cut-off grade is calculated on the basis that material of cut-off grade produces sufficient revenue to cover the estimated costs of mining and processing through to sales, including depreciation and produce a pre-determined profit. Ore reserves so estimated are adequate for determining the magnitude of an orebody but do not provide a sound basis for determining plant size and therefore capital investment in a new property or for expansion consideration on an existing property. From a financial analysis of this one ore reserve it is impossible to ascertain whether each increment of capital investment is providing the minimum acceptable rate of return, Other difficulties associated with the calculation of a cut-off grade including the determination of depreciation and the amount of pre-determined profit to be included in the cut-off grade calculation are outlined in the text. The proposed solution to determine optimum ore reserves and plant size for new properties avoids the complication of calculating a cut-off grade by computing a series of ore inventories using arbitrarily selected cut-off grades. A comparison of the cash flows generated by production from such ore inventories using incremental financial analysis clearly indicates the ore reserve and plant size which will best serve the corporation's investment and metal production goals. Incremental financial analysis of a corporation's operating mines and prospects assists management in assessing the comparative expansion and investment possibilities of each property for increasing or maintaining metal production on a long term basis.

Jan 1, 1969

By R. H. King

Recently, the North American mining industry experienced a severe recession, forcing managers to take dramatic steps to cut costs and compete in the difficult international market. Some of these steps were closing mines, reducing work forces, renegotiating wage agreements, and purchasing the most productive equipment. Managers are now looking beyond these traditional avenues and are focusing more on advanced technology. In the present environment, it is essential that mine operators obtain the maximum use of capital expended on equipment. However, mine workers do not obtain maximum efficiency or productivity from equipment because the adverse and hazardous mine environment impedes human performance. Also, the efficient use of large, complex machines calls for levels of precision that many times are beyond the capability of even highly trained miners. A possible solution to this problem is a machine that mines without operators - autonomous mining machines. However, numerous problems confront researchers who are attempting to develop such equipment. Some mining tasks are not always composed of a series of cyclic motions readily performed by factory floor robots. In addition, mining takes place in the geological environment where conditions are highly variable and unpredictable. As a result, these machines must be able to sense and adapt to variations in operating tasks and environment. Considerable autonomous vehicle research has been completed, especially for defense. However, autonomous vehicle (AV) technology has not advanced to practical application yet (King, 1988) and mining research is necessary in areas: representing mining specific knowledge; •analyzing and reasoning about sensor data in the mining environment; and •discovering completely new mining methods or new approaches to existing methods that become apparent when we remove the constraints imposed by the necessity of human operators. A specific machine, the LHD, can be used to show the problems for researchers who are attempting to develop autonomous machines for mining. This author chose the LHD because it can borrow concepts developed for autonomous navigation by military programs. But considerable mining research is also required. Furthermore, studies done at the Henderson mine, in Colorado, show autonomous LHD 's promise cost and safety benefits (King, 1988). At Henderson, LHDs load ore from draw points, tram to an ore pass, dump and return, or switch to another draw point. An autonomous LHD must sense vehicle position along the route, relate sensor data to stored-map information, to determine location, follow drift center lines, plan paths between dump position and initiate appropriate control commands, sense vehicle operating status and vehicle health, key on features or targets for special tasks like high speed turns, perform end of travel tasks (loading and dumping), and detect and avoid obstacles. These goals are similar to those for shuttle cars, trucks, and front-end loaders. Therefore, much of the technology is transferable. Each Henderson LHD extracts six to 40 dippers from each of a series of draw points. The LHD transports the ore to an ore pass within 55 m (180 ft) of the draw point, making the longest round trip 110 m (360 ft). The LHDs have very fast hydraulic dumping and loading systems that reduce the round trip cycle to less than one minute. Even though the LHD is capable of 500 trips per shift, the average production is 300 dippers. Man trip and lunch reduce available operating time to 6.5 hours per shift. Mucking difficulties (setting large boulders aside), operator breaks for activities like talking shop, and cleaning and smoothing roads further reduce operating time. Supervised autonomy can reduce the number of operating units by increasing operating time per shift since computer controlled machines can operate during lunch and between shifts and reduce operator errors. If dippers per shift increase from 300 to 350 (long-range goals are 500 dippers per shift), constant production requires only 10 operating LHDs and two spares. Manpower requirements drop from 24 to four by controlling five machines from one workstation. A review of technology available from the Autonomous Land Vehicle, the Advanced Ground Vehicle Technology, the Ground Surveillance Robot, and other programs, show the following differences between others work and mining industry needs: •If we focus initially on mobile haulage vehicles, we can navigate from a map. We do not need to explore. •We can modify the environment to reduce the navigation requirements. •We have a harsher environment than any of the research programs have encountered. •Our equipment must operate faster and more precisely than present AVs. •Our equipment must operate reliably over long periods of time. •We must have better onboard machine health monitoring and diagnostics. •The AV programs do not address geosensing. •The major AV programs are not cost-effective. For example, we cannot afford the computer power for robust image processing, yet. To computer control an LHD, we must replace the guidance and monitoring skills of experienced operators with sensors, computing hardware, interfaces, and several software mod¬ules. Experienced operators avoid collisions and load efficiently in piles that may contain oversize muck. Collision avoidance without an operator requires sensing all obstacles in the draw

Jan 1, 1991

By M. T. Worley

Joint Development Associates International, Inc. (JDA) began humanitarian relief and community development in Central Asia in1992, following the collapse of the former Soviet Union. Appropriate technology has played an important role in their efforts to assist those segments of society that are most vulnerable to poverty and disease. Three case histories are described to illustrate the successful implementation of simple, but effective technology in community development.

Jan 1, 2004

By George E. Williamson, Mikiya Higuchi, Michael T. Traylor

Extensive soil conditioning was required to allow Earth Pressure Balance(EPB) tunneling on the South Bay Ocean Outfall tunnel project in San Diego, California, near the Mexican border. This tunnel extends 19,000 feet out under the Pacific Ocean and was mined through soil formations including silts, sands, gravels, cobbles, and boulders. EPB pressures ranged from 3.0 to 7.0 bar, with the maximum pressures required when mining through the highly permeable granular formations.

Jan 1, 1999

By George L. Wilhelm

Many factors, some of which are not easily defined or described, must be considered in the design of a hydraulic backfill system. After participating in the design of several plants, I have a conviction that future refinements in sandfill systems must come in large part, from the merging of good design ideas and information from existing operating plants. It is important then, that we document and publish information on existing plant designs and their operating characteristics. This information will then be available for use by our successors and later innovators in hydraulic fill placement. The Mayflower hydraulic sandfill system is similar to other plants. The intent of this paper is to describe only this system's unique design and operating characteristics. I will not describe in any detail, the familiar elements of the system. I will document some of the observed hydraulic characteristics of the system, elaborate on some of the design situations that had to be solved, and will discuss operating factors that are not generally described in our technical literature.

Jan 1, 1968