Search Documents

By C. E. Jordan

Abstract. The U.S. Department of the Interior, Bureau of Mines, as part of its effort to maintain an adequate supply of minerals and metals to meet national economic and strategic needs, is conducting research on the pneumatic recovery of coarse mica. A system of crushers, screens, and zigzag air classifiers is used to concentrate coarse liberated mica particles from mica ore and from the waste tailings of abandoned mica operations. The plus 0.21-millimeter-size mica is effectively recovered by this method. The mica concentrates produced contain over 90 percent mica. The method recovered up to 78 percent of the mica in the samples. As a dry concentration method, the pneumatic-beneficiation technique may be advantageous in areas of limited water resource.

Jan 1, 1980

By John H. Bassarear

By 1968 Cyprus Pima was milling 38,000 tpd of copper ore using a conventional flowsheet consisting of three stages of crushing rod mills and ball mills. A 15,000 tpd expansion was put on stream late in 1971 using primary crushing, semiautogenous mills, and ball mills. Identical ore is treated in both concentrators. This paper shows the weight and life of each individual liner for each crusher and each mill over a four year period from 1974-1977. Power and media consumption are shown for the same period and a comparison is made between the two reduction methods.

Jan 1, 1980

By Brian E. McGee

The Federal Coal Management Program represents the culmination of several years of effort by the Department of the Interior (001) to reformulate the manner in which coal owned by the United States is leased and developed. These efforts began in 1970 with a study by the Bureau of Land Management (BLM), which indicated that unless drastic changes were made in. the federal coal leasing procedures, federal coal lands would be leased almost for the asking while production of coal from those lands had been decreasing. Consequently, informal action was taken in 1971, which resulted in no further leasing being authorized until February, 1973. At that time, a formal moratorium on most coal leasing was established, with exceptions granted only for leases needed to satisfy short-term needs such as maintaining existing mines or supplying reserves for new contracts in the immediate future. This leasing policy embodied a long term objective of developing an entirely new planning system for federal coal leasing, as well as to schedule the preparation of a programmatic impact statement for this new system. As a result of the 1973 moratorium and the ensuing application of short-term criteria, only 10 federal coal leases (covering approximately 30,177 acres) were issued from February, 1973, through January l, 1976.

Jan 1, 1982

By H. E. Rutherford

Monterey Coal Company has begun a geologic monitoring program in order to better understand our in-mine geologic conditions and to apply the knowledge gained to our mining operations. Two methods are used to collect information. The first is a monthly examination of conditions throughout the mine using a rapid mapping technique. The second is the detailed mapping of specific events encountered during mining such as faults and roof falls. The data gathered from both methods is correlated with operational statistics to create a geologic/production database. From the database, a monthly evaluation of mining conditions is made. Also, the database has proved useful in such areas as forecasting roof conditions and examining how faulting has affected mining operations.

Jan 1, 1984

By Lloyd W. Trevoy

Commercial production of heavy minerals from plant tailings streams is undergoing study by Syncrude Canada Lrd. When tar sand from an open pit mine is processed and up- graded to synthetic crude oil, heavy minerals can be recovered from the extraction circuit and can be upgraded to provide concentrates of zircon and titanium minerals. The titanium minerals concentrate consisting of a mixture of ilmenite, leucoxene and rutile, could be utilized as recovered or could be upgraded to synthetic rutile. With the construction of further synthetic crude oil plants in Western Canada a large reserve of heavy minerals will become available for utilization.

Jan 1, 1981

By Kevin Hegerle

The Henderson Mill has operated over a wide range of production rates, feed grades, manpower levels and recovery targets since start-up in 1976. Henderson Mill personnel, both management and hourly, have successfully responded to these changes by not only maintaining unit costs, but by actually decreasing unit costs. Methods of cost reduction have included conventional austerity programs, innovative technological improvements and creative work schedules. This paper addresses both maintenance and operating cost reductions and efficiency improvements.

Jan 1, 1986

By David A. Zegeer

It's a pleasure to be here, and an honor to be invited to address this distinguished group of professionals. Today, I'd like to begin with an overview of progress in coal mine safety and health. I'll discuss some current areas of concern. And I'll make some suggestions as to where we may be headed in the future. This year marks the coal industry's 15th anniversary under the Coal Mine Safety and Health Act, which took effect in 1970. We have come a long way in those 15 years. As a coal mining man from way back, I remember the era when the Coal Mine Safety and Health Act first was passed. Some of you may remember it, too. At that time, the safety and health of coal miners was in the public eye even more than it is at present. One reason was a mine explosion that killed 78 miners when it occurred in a large underground coal mine in November 1968. That disaster raised tremendous public concern about protecting the safety of miners.

Jan 1, 1985

By H. Weber

This paper is in three parts. Part I discusses the various types of cement clinker coolers now in full-scale operation. Part II is a detailed study of the criteria for selection of the type of cement clinker cooler best suited for a given installation. Part III covers a number of cooling problems and their solutions in some of the metals industries. The large and world-wide problem of cement clinker cooling has motivated much study and development and the coverage here of this work is somewhat detailed. In contrast the cooling problems of the metals industries are quite varied between industries and often quite different from plant to plant in the same industry because of basic differences in the requirements of the particular material being processed. Therefore the coverage of metals industries coolers is somewhat more general. It is believed that all of the technology covered here may be of interest to those working with the problems of cooling hot materials.

Jan 1, 1980

By Herbert F. Nyberg

The Black River Falls Mine is owned and operated by Jackson County Iron Company, a wholly owned subsidiary of Inland Steel Company. It is located in vest central Wisconsin, seven miles east of the city of Black River Falls. This is the first taconite plant in the state of Wisconsin. Iron mining started in this area in 1856 but soon failed due to the low grade ore and crude methods of mining and transportation. Inland Steel Company acquired the property in 1939. Some drilling and test work was done in 1940, but the economics of developing the property at that time were not favolable. Improved methods of concentrating and pelletizing in the 1960's made it possible to build the present plant. Due to the limited ore reserve of 45,000,000 tons with expected recovery of 33% it was necessary to limit the capacity of the operation to 750,000 TPY with a life of 20 years. There was some concern about an operation of such limited capacity. A million ton operation was considered the minimum size plant for a profitable operation.

Jan 1, 1976

By K. A. Natarajan, K. S. N. Murthy

Growth of Thiobacillus ferrooxidans on pyrite mineral surfaces and in 9K leach media was studied through estimation of bacterial protein in the different phases. Bacterial attachment was found to be governed by particle size of the mineral, period of incubation and by stationary or agitation conditions used during incubation. Increased bacterial growth in the liquid as well as on the solid phase was observed with decreasing particle size and increasing incubation periods. Increased bacterial attachment to pyrite mineral surfaces was observed to promote iron dissolution.

Jan 1, 1993

By Anna Sieminska-Lewandowska, Monika Mitew-Czajewska

"The construction of 6.3 km long central part of 2nd metro line in Warsaw was completed in September 2014 (7 stations - out of which three 25m deep stations - built using cut and cover method; two single-track tunnels constructed using four EPB TBMs as well as a short NATM section with soil freezing below the existing road tunnel). Central section of the 2nd metro line was opened to public after verification and testing in March 2015. Design and build tender for the extension of this line in East (three stations) and West direction (three stations) was announced with total length of running tunnels – approx. 5 km. Detailed description of a very complex geotechnical context, different construction methods, challenges encountered and solved during construction and finally lessons learnt on this interesting project are presented in the paper. DESCRITPTION OF THE PROJECT Introduction The very first concept plan of the metro system in Warsaw was designed several years after regaining independence by Poland in 1918. In 1929, following the geotechnical survey, design works begun, but the economic crisis of the 1930s stopped it. After a few years of break, in 1938 a coherent concept of the metro network was proposed to be implemented in phases over the next 35 years. In total, construction of 46 kilometers of metro, including 31 km of tunnels and 15 km on surface, was planned. Unfortunately, World War 2 made the implementation of those plans impossible. In the post-war period several metro designs were elaborated, but none except one was scheduled for implementation. Construction of the 1st, 23.1 km long, North-South line commenced in 1983 and finished in 2008 (Sieminska-Lewandowska et all. 2009). Nowadays, Warsaw covers the area of 517 km2 and, according to year 2014 statistical data, the city has much more than 1.7 million inhabitants. Only one operating metro line is not sufficient for such a populated city. Up-to-date metro plan, shown on Figure 1, includes also 30.5 km long 2nd metro line. It’s route is divided into four sections: Western Section with the length of approx. 9.2 km and 9 stations, Central Section with the length of 6.3 km and 7 stations, North-East Section with the length of 7.7 km and 6 stations, South-East Section with the length of 7.1 km and 6 stations. The construction of the central part of the 2nd metro line in Warsaw was completed in September 2014 and its operation started in March 2015. The paper focuses on challenges encountered and solved and lessons learnt during construction of the central part of the 2nd metro line in Warsaw."

Jan 1, 2016

By David A. Lee

It was estimated in Chemical Week1 that the uranium fuel requirements for the U.S. Electric Utility Industry by the mid 1980's would be about four times that-of what it is today. This corresponds to approximately 45,000 tons per year of 'yellow cake' - of which a good portion is represented by ammonium diuranate - vs. the 11,700 ton total estimated for 1975. Perhaps just as significant is the 40-fold increase in thirty years projected for the entire world since 1970. Thus by the year 2000. 'yellow cake' production could be in the order of [3]50.000 short tons annually.2 'Yellow cake', so named because of its inherently bright yellow color, is a finely divided precipitate that can be formed after the leaching step when refining uranium ores. Feed solids enhancement then occurs to at least 50% by weight using filters or centrifuges This is followed normally by drying and then calcining with the conversion of ammonium diuranate to triuranium octoxide represented by the following equation: [9 (NH4)2 U2 07 heat 14 NH3 7 + 15 H2O7 + 2N2/ + 6 U308 4] Theoretically, assuming 100% conversion every 100 kgs. or 100 lbs. of ammonium diuranate will result in 90 kgs. or 90 lbs. of triuranium octoxide.

Jan 1, 1976

By Ernest E. Thurlow

The Geology Division of Northern Pacific Railway Company has adapted to its exploration efforts field procedures for geochemical sampling and semi-quantitative analysis which have been developed through research by the U. S. Geological Survey. The sampling is done in conjunction with reconnaissance geologic mapping on aerial photographs or during field checking of maps which have been prepared largely by photogeologic interpretation.. Stream sediment or soil samples are taken and readily soluble combined heavy metals are extracted with ammonium citrate followed by colorimetric titration with dithizone at the sample site. The effectiveness of this approach has been demonstrated both in positive and negative results, thereby assisting in the elimination of large areas of land from further immediate attention and in providing targets for followup exploration. An occasional sample is submitted for spectrographic analysis as a check on the possible presence of other elements of economic significance. Field laboratory procedures are also being implemented for determining molybdenum, mercury, and other metals which may be valuable in themselves or useful as pathfinder elements in outlining mineralized areas. A lead-zinc occurrence in Oregon and a copper deposit in Montana were readily detected and outlined by stream sediment and soil sampling and a heavy metal anomaly that lacks obvious interpretation has been found in northwestern Montana. Detailed mapping and additional sampling are followed by other exploration techniques if warranted.

Jan 1, 1964

By M. Karmis

The design of coal-mine layouts is based on the knowledge of a broad range of geological and geotechnical parameters, which must be determined from a sequence of exploration programs. It follows that any weaknesses in selecting, determining, interpreting or utilizing these data are inevitably reflected into the mine-planning process. In this paper, the main methods of exploration are reviewed and evaluated with the emphasis on acquisition, interpretation and storage of variables pertaining to mine-design. Some common problems are highlighted and recommendations are given for improving the utilization of data and optimizing coal-mine design procedures.

Jan 1, 1980

By Erwin K. Roesner

The difficulties encountered while sinking deep shafts for Potash Mines in southern Saskatchewan have been the subject of several papers in the past. Geological and hydrological conditions of the strata overlying the potash deposits require special techniques for ground and water control during shaft sinking. The easily soluble potash ore requires the lining of these shafts to be virtually watertight to assure long term and safe operation. This paper describes the construction of the most recently completed potash shaft for the Potash Corporation of Saskatchewan. The shaft was designed and constructed by Thyssen Mining Construction of Canada Ltd. and it is located near Lanigan, approximately 110 km east of Saskatoon.

Jan 1, 1980

By J. Davitt McAteer

Improvements in the control of coal mine dust have occurred over the past 25 years. Simultaneously, dramatic improvements in coal mine production technology have occurred, particularly at mines where longwall systems are in use. Production rates of longwall systems have quadrupled since 1978, and dust generation on these systems has significantly increased. However, technology to address control of the resulting increased levels of respirable dust has not kept pace, and many high-production longwall sections continue to experience problems with respirable dust control. This paper seeks to enlist the entire mining community in the effort to resolve the health problems presented by excessive levels of respirable coal mine dust, particularly on longwall systems. These systems are expected to increase in number and length, and to generate increasingly higher levels of dust as production rates of these systems continue to rise.

Jan 1, 1995

By T. R. Raponi, D. Barnes

The Williams Mine mines and mills 6000 t/d (6600 stp’d) of gold ore using SAG/ball milling, leaching and CIP, electrowinning and refining. Electrowinning, high-pressure cathode washing, filtering, retorting and refining are based around the use of knitted stainless steel mesh cathodes. Their primary advantage over conventional steel wool cathodes is that electrowon gold can be washed off and the cathode can then be reused. Typically, the knitted cathodes have a useful life of up to 15 months. Gold production of up to15 t/month (50,000 oz/month) is easily processed with this system. Presented is a description of this operation, including a review of the equipment and performance data.

Jan 1, 1992

By Jerry Grott

Southwest Salt Company is solution mining the Luke Salt Body of probable late Miocene age. The discovery hole, from which the first core was recovered, was drilled in 1968. The deposit was encountered at a depth of 880 feet, and the bit was still in salt at the bottom-hole depth of 4,500 feet. The solar ponds, developed on land formerly dedicated to agriculture, have an annual capacity of about 90,000 tons. Because land values are very high, mining rates and procedures are governed by the need for near-saturated brine to minimize land requirements. Because of the frequency of dust storms, the salt operation uses a unique wet-harvesting method. Most inventory is kept in the ponds under brine and harvested only a few days before shipment. Studies of the nature of crystal growth and the distribution of windblown and brine impurities led to the development of procedures for processing salt of high chemical purity and low insolubles content. Chemical purity exceeds that of most salt produced in fuel-fired evaporators. Salt is shipped from Phoenix as tar east as west Texas and as far west as central California. Occasional shipments have been made to Hawaii and Alaska.

Jan 1, 1987

By Fred H. Seymour

In spite of the progress made by geostatistical theory over the years, evaluation of low grade open pit gold deposits continues to be challenging. Many Carlin type deposits are modelled from exploration drilling spaced on 10C foot centers. From these drill holes, 50 by 50 by 20 foot blocks containing about 4000 tons of material are estimated. The block size is a compromise between being large enough for a good geostatistical estimation and being small enough for practical pit limit analysis and mine planning. Most of these gold deposits are highly variable and include ore and waste zones that are too small to be properly defined from exploration drilling information. Because of this, selective mining is controlled by sampling closely spaced blast holes where the density can be as high as 50 blast holes per exploration drill hole intercept. Figure 1 illustrates an example of the ore/waste contact definition before and after blast hole sampling. With exploration information only, a tentative ore/waste contact can be drawn between the exploration blocks.

Jan 1, 1989

By Michael M. Carroll, Zhu-ping Duan, Han-ping Chin

INTRODUCTION The inelastic stress-strain behavior of rocks has urged engineers to seek for the possible application of plasticity to engineering pro¬jects such as tunnels, oil wells, dams, etc. for a long time. Early efforts in this direction have tentatively used the classical theories to solve some axisymmetric problems, in which the rocks were treated as perfectly plastic and nonfrictional materials (Talobre, J. A., 1957). Meanwhile, one of the fundamental assumptions is that the volume strain of elastoplastic material is purely elastic. Drucker and Prager (1952) developed a perfectly plastic and frictional model with a generalized form of Mohr-Coulomb law, which serves as both failure criterion and yield criterion. Although the associated flow rule gives unacceptably large dilatancy, this model is a very important step to deal with the frictional behavior of geological materials. As a further step, Roscoe et al (1963) and Schofield and Wroth (1968) proposed a Cam-clay model, which accounts for the yielding before the material reaches a failure envelope and reflects the plastic volume strain as a strain hardening factor, and the open end of the Drucker-Prager envelope is capped by a family of yield surfaces, the envelope is made conforming with crit¬ical void ratio line. The proposed shapes of the cap have been based on experimental data and on convenience of mathematical descrip¬tions. Drucker, Gibson and Henkel (1957) introduced a spherical cap for soils, while in Cam-clay model the cap is semi-logarithmic yield function derived from the result of triaxial tests. DiMaggio and Sandler (1971) proposed an elliptical model for sand, in which the hardening function depends exponentially on plastic strain. Sandler et al (1976) used a plane cap model to express the behavior of a wide range of geological materials of which the nonlinear hysteretic nature is significant. Mizuno and Chen (1982) illustrated the physical mean¬ing of cap models and their adaption to finite element calculation. In recent years, Carroll et al (1972, 1980) have studied the com¬paction of porous materials under hydrostatic pressure and discussed the mechanism of the nonlinear response thoroughly. Analytical and numerical analysis of the hollow sphere model by Curran and Carroll (1979) predicted an initial yielding surface, dependent on the initial porosity, and showed a strong coupling between hydrostatic and deviatoric effects. All these main features from the abovementioned theoretical research are visualized by the experimental data on Boise sandstone (1984). The combination of such previous work would be logically the construction of a plasticity model for porous rocks which, following the tradition of assigning the name of birthplace to a special model, is called Cal-Rock model (Carrol, M. M., 1984). The results of triaxial tests along different loading paths reveal the compaction characteristics for deviatoric and hydrostatic stress separately. the fitting of the nonlinear stress-strain curves leads to a construction of yield surfaces. Moreover, an uniaxial strain test gives the strength envelope which is the critical state line. The whole model is composed in the frame of elasticity theory. The concept and representation of plasticity used here are in the spirit of Naghdi¬Casey theory (Casey and Naghdi, 1984 and 1984, Naghdi and Trapp, 1975). In order to find the way of using such a plasticity model in engineering problems, the stress field in a thick-walled cylinder of porous material is calculated. This is an axisymmetrical problem with plane strain, which is an idealization of oil well in an infinite medium. Because the constitutive relation is highly nonlinear, a numerical method has been utilized to obtain the solution. CONSTRUCTION OF CAL-ROCK MODEL (1). Elastic-plastic constitutive equations The basic assumption is that the yield surface in stress space depends on one parameter, namely the plastic volume strain, as the data on Boise sandstone suggested. Starting from this point, the theory formulated in stress space and in strain space by Naghdi and his co-workers (1975, 1981) can be simplified. The simplified yield function is

Jan 1, 1986