Search Documents

By Gregg J. Hodges

The Stillwater Mining Company, a partnership of The Pittsburg & Midway Coal Mining Co. and Manville Corporation, began commercial production of flotation concentrates from the western hemispheres' only primary platinum palladium deposit at Nye, Montana in March 1937. In the fall of 1987 an integrated pilot plant testing campaign of electric furnace smelling and oxygen? blown converting confirmed the feasibility of further upgrading to semi? refined matte or 'white metal". In the summer of 1990 the production smelter was brought on-line at Columbus, Montana. This paper describes the technology transfer from the pilot to the production smelter. Emphasis is placed on flowsheet development and the scale factors between the test and production furnaces and gas cleaning plants. The metallurgical results of the pilot plant and of the early months of production of the commercial works are also compared.

Jan 1, 1991

By Bo-Hyun Kim, Mark K. Larson

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) have advocated the use of instrumentation in underground mine ground control studies to aid in understanding failure mechanisms and to calibrate numerical models. The purpose of these efforts is to reduce accidents and fatalities in underground mines resulting from inadequate design of mining layout or supports. A recent examination of some results of stress change measurement raised some questions about the validity of elastic solutions in ground, such as coal. Particularly under deep cover as is prevalent in the western United States, the coal around a borehole would likely have yielded so that post-yield behavior would govern the response of the instrument.A numerical experiment was conducted by NIOSH researchers using the FLAC software (Itasca Consulting Group, 2016) to investigate the response of the borehole pressure cell (BPC) and the biaxial stressmeter to varying degrees of plastic behavior. The pre-encapsulated BPC cell pressure exhibits increasing departure from the elastic case with decreasing post-peak-strength slope of the stress-strain curve. On the other hand, because the BSM usually provides much more confinement to the surrounding rock than does the BPC, the measurements obtained from the BSM do not depart significantly from the changes in secondary principal stresses and directions as calculated by the elastic solution.INTRODUCTIONSeveral years ago, Larson et al. (2000) described several instruments that NIOSH had used in underground field studies and how to monitor them with dataloggers. This information is still relevant because of the need to understand how excavation affects the stability of mines and thus, the safety of mining personnel. One class of instruments described in that paper includes those instruments that measure change in rock stress. Although several such instruments might be used to measure stress change, the focus of this paper is on two instruments with which NIOSH has had more recent experience—the borehole pressure cell (BPC) (Geokon, 2018a; RST Instruments, 2018) and the biaxial stressmeter (BSM) (Geokon, 2018b). Other instruments, such as the CSIRO hollow inclusion stress cell (HICell) (Earth Sciences, 2019; Worotnicki and Walton, 1976) may be included in future studies.Early studies in the development of the BPC were those of Panek and Stock (USBM, 1964), Sellers (1970), Lu (1984), and Babcock (1986). Babcock’s work is particularly useful, but his setting and testing range was far below what we experienced in the NIOSH study, and it was Babcock’s data reduction scheme from his laboratory experiments that was used to calculate stress change in the NIOSH study (NIOSH, 2019a)."

Jan 1, 2019

By S. Sener

In this investigation, the changes in the grindability of both ulexite and colemanite related with the different structural modifications created by the heat treatment were examined with respect to work index (Wi). The effects of the heat treatment temperature and time on grindability index were also investigated. It was observed that, heat treatment significantly affected on the grindability of ulexite. The work index of original ulexite was found 7.11 kWh/shton and decreased to 3.5 kWh/shton level within 200-480°C for 60 minutes. On the other hand, the work index of original colemanite was found as 6.48 kWh/shton and no appreciable change was observed when heated up to 320°C. Thermally assisted comminution can be used to improve the grindability characteristics of ulexite. Besides, the different behaviour of ulexite and colemanite under heat treatment can be used for their separation. The artificial mixture of ulexite and colemanite could be separated with over 90% recovery by utilizing their different grindability characteristics by thermal treatment, semi-autogeneous grinding and screening.

Jan 1, 1999

By Luther W. Hyde

Ground water, one of Florida's most valuable resources, is also one of its most abundant. The State is fortunate to have several prolific ground- water reservoirs that yield tremendous quantities of water to wells and to some of the world's largest springs. These ground-water reservoirs, or aquifers are of two types artesian and nonarteaian. Ad artesian aquifer is one that contains water under sufficient pressure to rise above the top of the oontaining formation. A nonartesian aquifer is one that contains water which is not confined, and the upper water surface (water table) is free to rise and fall. The principal source of ground water in Florida is the artesian Floridan aquifer which supplies most of the water users in the State. Nonartesian sources include the Biscayne aquifer of southeastern Florida, the sand-and-gravel aquifer of extreme western Florida, and a shallow aquifer which lies at depths of less than 100 feet over much of the State. The accompanying map shows the approximate areas where these aquifers are the main source of supply; however, the boundaries do not represent the areal extents of the aquifers. For example, the Floridan aquifer extends beyond the southern boundary shown on the map, but it is not of great economic significance there because the water is highly mineralized. Aquifers other than the four described occur in the State, but they are, for the most part, of minor significance. One of these is an artesian aquifer which is formed by permeable zones that occur locally within the confining beds above the Floridan aquifer.

Jan 1, 1966

By Donald V. Fites

The evolution of open-pit mining has been rapid during the last two decades. The development of larger, more productive and efficient equipment has been one of the key factors in this open-pit advancement. Selection of the proper equipment and its correct usage is paramount to successful operation while maximizing return on investment. The quantity of material being moved prior to mining the saleable product is increasing at a significant rate. For example, at a southwestern copper mine more than two hundred million tons of over- burden have been removed prior to exposing an ore which contains less than 1% copper. A recent survey of twenty-three Western Hemisphere copper mines reveals the average strippingratio was 2.2:l with a range of 0.9-8.5:l. In the face of increased mineral demand, the resulting technological developments and rising overburden to ore ratios, many open-pit mines now use totally different concepts for the removal of ore and overburden. An increasing number of these concepts now being installed include wheel tractor scrapers as a major part of the material handling system for unconsolidated overburden removal. To say scrapers move only unconsolidated overburden is incorrect. On the contrary, ripped phosphate rock, copper ore, iron ore, and moderately consolidated overburden are also being moved by scrapers in various areas of the world. As reported in the Minerals Year- book, however, about one-half of the material moved in metal and non-metal mines is never drilled and blasted or broken by other means. We will, therefore, in this paper, concentrate on the role of wheel tractor scrapers in unconsolidated overburden; the area of greatest usage.

Jan 1, 1969

By V. Steinbach

Non-renewable mineral raw materials are grouped into three categories to investigate ways leading to sustainable use of natural resources: 1.) metallic resources, 2.) non-metallic resources with the exception of the fertilizer minerals, and 3) the fertilizer minerals for the nutrients nitrogen (N), potassium (K), and phosphorous (P). With the exception of minerals in Group 3 which are essential for plant growth, mankind does not need raw materials as such, only the intrinsic property of a material that fulfils a useful function. This is especially true for non-metallic materials. Metallic resources have the best chance to become renewable if one makes optimal use of the resources of the man-made technosphere. For the fertilizer elements K and N there does not exist a problem, because sea water or air respectively provide an inexhaustible source for them. This does not apply to P however. So P is serving as one of our apposite case studies for solving sustainability challenges. For all the challenges along the road from a non-sustainable to a sustainable resource economy technology can be envisioned to come to the rescue provided conditions that are considered to be essential for sustainable use for all natural resources-- affordable renewable energy and human ingenuity to find new solutions for functions, to optimize processes and to minimize losses-- are satisfied.

Jan 1, 2011

By Jeremy Cawley, Jeff Murphy, Horry Parker, Brock Gaspar, Jake Keegan

The Lower Olentangy Tunnel project includes 47,000 cubic yards of planned ground improvement for earth pressure balance machine (EPBM) tunneling (5.2 km) and microtunneling (335 m) in glacial soils. Jet grouting started in late 2021 and will continue through 2023 to complete operations at 5 shafts, 14 safe havens, 5 watermain ground improvement zones, and a river crossing. Typical jet grout columns are installed at depths between 15–24 meters. Discrete soil-cement blocks range from 267–8,900 cubic yards in volume. This paper discusses the methodology, testing, and technical considerations associated with jet grouting operations in glacial overburden across an urban environment.

Jun 13, 2023

By S. A. K. Forson, Newton A. Amegbey

In order to investigate production decline in Tarkwa Goldfields Ltd., located in a tropical rain forest, amongst other areas, a health survey was conducted with the aim to see 1. The health status of the workers. 2. Which parameters carry the most information about the health situation and which of them can be applied easily during screening programmes. 3. What steps could be taken to improve the situation. In all 249 workers were investigated. A non-invasive method involving taking of body weight and arterial blood pressure was used. All subjects were required to answer a questionaire. Emphasis was placed on the history of malaria and diarrhoea within the last six months. Both management and workers co-operated fully. Another set of 110 workers from a neighbouring tyre factory were also investigated for control. Among the underground workers, the percentage body weight loss during a shift increased with decreasing body weight. Dehydration levels could be as much as 4 to 5% of body weight. This could be attributed to the fact that workers took insufficient or no water during the shift. The health status of the mine workers was generally poor and in our opinion malnutrition combined with malaria severely threatens the health and well-being of the workers. Hypertension is also a problem. An improvement in production is intimately linked with the well-being of the workers.

Jan 1, 1989

By Hemendra N. Kalia

To plan a safe and efficient coal mining operation, the design engineer should use all the available information regarding the property to be exploited. The reliability of the mining operation must be as high as possible so that the plants relying on the coal can operate at the maximum design capacity. A good design should incorporate all of the known geological characteristics of the deposit, the structural and physical properties of the coal, as well as the rock which will form the roof and floor of the mine openings. A systematic method is proposed as a guide to insure a mine design that will be safe, efficient and will minimize surface disturbances resulting from mining operations. It is anticipated that the method proposed will result in maximum extraction at perhaps minimum cost to the operator. In general, to develop a mining area, several factors are systematically reviewed: (1) determination of the economic minability of the deposit, (2) the computation of the coal reserves, (3) the marketability of the coal, and (4) the life of the property. In general, boreholes are drilled in a predetermined pattern and geophysical or geological methods are used to log the boreholes. The information so obtained is primarily used to determine the quality and the extent of the deposit and to determine to some extent such geological features as faults, barren areas, washouts, and channels.

Jan 1, 1973

By David J. Dunn

Mill liner design is an important factor in grinding. Testing and selection of the optimum liner profile for a given set of mill operating conditions can improve mill capacity, liner life, and liner wear rate At a time when mill avilability is at a premium, production costs are going up, and lead time for mill liner castings is a year or more, the mill liner that grinds best, lasts longest, and costs least is a necessity for economic mill operation. In testing four mill liner profiles for 13' x 12' overflow ball mills, Climax found that an improved design increased mill tonnage by 3 tons per hour while reducing finish grind by 1.7% + 100 mesh, reduced liner wear rate, and almost doubled liner life.

Jan 1, 1976

By Weston Bourret

The need for wartime supplies of uranium for the Manhattan Project prompted a 1944 study of uranium in South Africa. Uraninite had been reported by R.A. Cooper in 1923 in a Witwatersrand heavy- mineral concentrate, and the search for uranium, therefore, included the district's 30 operating mills. The method of investigation was simple: take bulk concentrate samples from the Wifley tables and determine their mineralogy. Samples were taken on a daily basis, although weekly composites also were taken of some mills. In 1944, most mills had simple gravity circuits and produced (I) a gravity concentrate, and (2) an all-slime [-75 pm (-200 mesh)] product. The tonnage throughput was known, and from that, head assays could be calculated. Concentrate samples were sent to the United States for chemical analyses. A Geiger counter set up in a Johannesburg hotel room provided preliminary data. The early data showed uraninite to be widespread. Microscopic, mineragraphic, and siezing tests were all under- taken in Johannesburg. Ultimately, tests led to a high grade (+90%) uraninite concentrate. Platinum and other heavies were the impurities. In seven months, the investigations had reached the stage where it was possible to forecast an annual production of 5.4 to 7.3 kt (6,000 to 8,000 st) of U3O8. The estimate is still realistic. Additional details are found in Bourret (1981).

Jan 1, 1991

By Brent W. Madsen

To assist in fulfilling the Bureau of Mines goals of maintaining adequate mineral supplies to meet national economic and strategic needs, and to minimize the environmental impacts associated with mineral-processing operations, a leaching-solvent extraction-electrowinning technique was compared with a leaching-cementation technique for processing low-grade copper ores. Large-scale laboratory column leaching tests (6 to 7 tonnes) were conducted on minus 37-cm chalcocitic ore using ferric sulfate leach solutions at 25° C. Two columns contained 11 percent minus 1.27-cm fines, and two columns contained 32 percent minus 1.27-cm fines. After 416 days of leaching ore samples containing 11 percent minus 1.27-cm fines, copper extraction was 48 and 51 percent for the leach-cementation and leach-solvent extraction-electrowinning procedures, respectively. When leaching ore samples containing 32 percent minus 1.27-cm fines, the leaching-solvent extraction-electrowinning technique extracted 60 percent of the copper after 568 days, whereas the leaching-cementation technique extracted only 48 percent of the copper. In the latter test, leach solution ponded on the ore, which reflected a decrease in ore column permeability. The decreased permeability was attributed to the generation of excessive amounts of iron salts during cementation; the salts precipitated on the fine ore particles and in the interstices, thus plugging the column. This decrease also lowered the available oxygen, resulting in poor aerobic bacterial activity which slowed the oxidation rate of ferrous ions to ferric ions. Sulfuric acid required to maintain a leachant pH of 2 was nearly halved when copper was recovered by solvent extraction and electrowinning rather than by cementation.

Jan 1, 1979

By Bryan C. Smith, Duane R. Skidmore

Volumetric mass transfer coefficients and gas holdups were measured in a concentric tube airlift reactor designed for the microbial desulfurization of coal. The slurries were comprised of an acidified basal salts solution containing thirteen different weight percents of coal (74 µm Ohio #1) at three temperatures. An enhancement in the mass transfer coefficient, KLa, with respect to that measured in pure solution was found at weight percents of 5 (volume fraction solids, ES = 0.035) or less, the greatest enhancement being as great as 37% at approximately 2 weight percent (ES = J 0.014). At higher solids fractions, the mass transfer coefficient decreased with further solids additions, decreasing by as much as 91% at 40 weight percent coal (ES = 0.315). KLa increased with temperature at all solids concentrations, the greatest increase being 392% at 72°C vs that measured at 30°C. Gas holdup, EG decreased with all increases in solids loading by as much as 65% and increased by as much as 67% with temperature. KLa and EG were correlated with operating conditions separately, and the separate correlations combined to yield overall correlations for the mass transfer coefficient and for the gas holdup. The correlations are suitable for inclusion in system models devised earlier for microbial coal desulfurization processes, and may be used for design, operation and cost estimation for such systems.

Jan 1, 1989

By L. D. Boughton

Solution mining projects are conducted through one or more boreholes which penetrate en ore body. Proper drilling, completion and maintenance of the boreholes, therefore, is essential to the success of any solution mining operation. Wells drilled for solution mining encounter problems quite similar to problems encountered by the petroleum industry in drilling, completing and maintaining wells for the production of oil, gas or water. Many of the services developed and much of the experience gained by the petroleum industry is applicable to solution mining wells. As in the petroleum industry, each individual wellbore and ore body in a solution mining project provides its own problems. These vary greatly from well to well, and it is not possible to set down data or outline programs that will apply to all wells. Instead, the design of the drilling, completion, production and maintenance programs should be worked out for each individual well. The purpose of this paper, then, is to generally describe materials, equipment and techniques available for these programs and to discuss the purpose and sequence of their use.

Jan 1, 1971

By Richard A. Thomas, Liming Yuan, Wei Tang, JOHN SOLES

Lithium-ion battery applications are increasing for battery-powered vehicles because of their high energy density and expected long cycle life. With the development of battery-powered vehicles, fire and explosion hazards associated with lithium-ion batteries are a safety issue that needs to be addressed. Lithium-ion batteries can go through a thermal runaway under different abuse conditions including thermal abuse, mechanical abuse, and electrical abuse, leading to a fire or explosion. The NIOSH Mining program is conducting research to prevent and respond to lithium-ion battery fires for battery electric vehicles in the mining industry. In this study, experiments were conducted to investigate the effectiveness of different suppression systems including dry chemical, class D powder, and water mist for lithium iron phosphate battery pack fires. The effects of activation time and release time of the water mist system on the suppression of lithium-ion battery fires were studied. The results of this study may be helpful for developing strategic firefighting and response plans for battery-powered vehicles used in mining.

Feb 17, 2024

By Kate Willa Brown Requist, Eric Lutz, Moe Momayez

As air quality sensor networks become increasingly popular in underground coal mines, it is important to generate paradigms for the application of the collected data. To date, air quality sensing has been primarily used as an early warning system for hazardous air conditions. Using data collected from a network of sensors in a US underground coal mine, we have created multiple visualization methods to show the interactions of carbon monoxide evolution with ventilation airflow. These visualization methods can allow for further analysis of the source of contaminant, as well as better data resolution across the area of concern within the mine. By utilizing univariate spatial interpolations, we present methods for identifying the movement of carbon monoxide at one-minute intervals. The resulting visualizations display the evolution of carbon monoxide concentration across a sizeable study area over a period of 14 minutes.

Jun 25, 2023

By K. Johnson, B. Schiffer

Demonstrating aquifer restoration is an essential component of regulatory approval needed to mine uranium, copper, and other minerals by in-situ recovery (ISR). A PHREEQC geochemical model provided a useful means of forecasting the time for restoration and predicting future groundwater quality following low pH mining at Strata Energy’s Ross ISR Project in northeast Wyoming. The model simulated groundwater quality at three phases of the process: at the end of mining; during restoration; and post- restoration. The model utilized the one-dimensional reactive transport and dual porosity features of PHREEQC. Mineral surface ion-exchange, dissolution/precipitation reactions, and adsorption processes were simulated to estimate water quality as the pH was shifted from circumneutral to acidic during mining and back to neutral during restoration. The model results showed that cost-effective management of mine water could meet regulatory requirements. Additionally, the model was used to interpret results from a field trial and inform operational decisions. The predictive approach and geochemical understanding developed have application in assessing aquifer restoration for other ISR projects.

Mar 2, 2022

By A. Jahedsaravani, M. Massinaei, M. H. Marhaban, N. Mehrshad, M. I. Saripan

"It is well known that froth visual features reflect the operating conditions of the flotation process, so that being able to accurately obtain the froth properties is the most significant criteria to optimize and control this process. Froth segmentation is a useful procedure that can determine the bubble size distribution. Several algorithms have been proposed in this field, but marker-based watershed transform shows the best performance. In spite of this fact, the algorithm suffers from oversegmentation in cases when the flotation froth includes large bubbles along with small ones. In the paper, the marker-based watershed method is modified to prevent oversegmentation of large bubbles. The developed algorithm is validated using some froth images captured at different operating conditions, so the results indicate that the method can segment the mixture of big and small bubbles effectively.IntroductionFroth flotation is a widely used process for separating valuable from gangue minerals. Effective control of flotation circuits has a dramatic effect on overall performance of a mineral processing plant. In most flotation plants, process operators monitor the froth surface visually and make adjustments to process parameters based on their interpretation of the surface appearance and their idea of the appearance of an ideal froth. However, due to natural complexity of the flotation process, achieving optimal control is often not possible for human operators.In recent years, attempts have been made to control the flotation circuits using machine vision systems (Moolman et al., 1995; 1996a,b; Bartolacci et al., 2006; Kaartinen et al., 2006; Vanegas and Holtham, 2008; Aldrich et al., 2010). The froth bubble size distribution is the most significant control variable that reflects the operating conditions in a flotation machine. To date, a number of approaches have been proposed for bubble size measurement from froth images, including segmentation (Sadr-kazemi and Cilliers, 1997; Wang et al., 2003; Mehrshad and Massinaei, 2011), texture spectrum (Nguyen and Thornton, 1995), wavelet (Liu et al., 2005), an improved texture spectrum approach, a method based on binary images (Lin et al., 2008) and, finally, using interfacial morphological information (Yang et al., 2009)."

Jan 1, 2015

By Peter Schmäh

Pipe-jacked tunnels are considered for a large variety of applications from water and sewage, cable ducts to challenging pipeline crossings or landfall construction. In most cases, Slurry MTBMs are used to carry out these projects. Continuous further development of technological features for pipe jacking plays a key role to overcome feasibility limits and to meet increased project requirements. As tightened safety regulations in terms of accessibility and escape routes increasingly limit the options of small segment lining tunnels in the diameter range below 4 m, 13 feet, pipe jacking has partially taken over. During the last decades, a growing number of large-diameter and long-distance pipe jacking projects have been completed. Experienced contractors successfully use the technological capacity of the MTBM equipment. The machine and cutting wheel have to be designed according to the ground conditions. Bentonite lubrication and interjacking stations are key factors to keep push forces moderate. For long pipe jacking drives, a so-called push module can be installed in the machine can, to be able to switch from pipe jacking to segment lining in case the machine gets stuck. The overall aim is to provide clients and the tunnel construction industry with safe and economical solu- tions for successful project execution. This presentation will present international milestone projects and will also discuss the latest developments in automation, related opportunities and limitations, and the future of digitization and artificial intelligence in pipe jacking.

Jun 23, 2024

By G. E. Rouse

Anomalies of sulfur dioxide and other gases have been defined, by direct measurement, around various sulfide bodies. These readings were made (1) in soil gas and (2) in the atmosphere, from both ground vehicles and, to a limited extent, from helicopters. Test areas included porphyry copper and molybdenum deposits, sulfide bearing vein systems, pyrite zones associated with sandstone uranium accumulations, and pyrite-bearing mine dumps. Some of the deposits are covered by as much as several hundred feet of overburden or barren rock, while others outcrop, or have been exposed by mining operations. Depending on local conditions, background values of sulfur dioxide in soil gas and the atmosphere range from 1 to 15 parts per billion. Using present techniques, anomalous readings are recognized at approximately two times background. Apparent "depth penetration? on known deposits has ranged to several hundred feet. Readings have been made over known deposits from a helicopter and ground vehicle moving at up to 40 mph. The rate at which the survey may be carried out depends largely on the size and extent of the anomaly. The existence and magnitude of sulfur dioxide anomalies around sulfide-bearing deposits is a function of geology, target size, soil moisture, and climatic conditions such as temperature and temperature changes, barometric pressure, wind velocity, and precipitation. Industrial S02 pollution can effectively mask the presence of the anomalies sought.

Jan 1, 1971