Search Documents

The Subtropolis mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, Ohio. In February 2018, mine management began implementing a heading reorientation to better control the negative effects of excessive levels of horizontal stress. The conditions in the headings improved, but as expected, stressrelated damage concentrated within crosscuts. The mine operator has worked to lessen the impact of the instabilities in the outby crosscuts by implementing several engineering controls. With the implementation of each control, conditions were monitored and analyzed using observational and measurement techniques including three-dimensional (3-D) LiDAR surveys.

Jan 7, 2020

By Jacques Nantel

Mechanization has been at the core of productivity improvements since the industrial revolution. During the past 20 years, mining has derived spectacular progress from mechanization. In the future, however, mechanization alone will not be enough. In the next few decades, automation will bring about new generations of highly productive and safe machines, with low operating costs. Increased use of new and better technology is generally accepted as the prime factor capable of closing the productivity gap. The productivity gap is the difference between inflation and metal prices. The three S-curves in Fig. I represent the evolution of technology in general, and mining in particular. TI represents incremental changes. the dominant sort of technology changes in the mining industry: - Better drills, electric hydraulic drills vs. pneumatic drills, the drilling rate is twice as fast. - Better steel and bits, to accommodate the higher performance drills. - Improved chemical explosives. - Bigger trucks in open pits.

Jan 1, 1993

By J. Hansen

This paper has been written for presentation during the Open Pit Mining Session at the SME Annual Meeting and Exhibit, Denver, Colorado, February 26 to 28, 2001. The paper addresses the application of automated monitoring of electric rope shovels to improve performance and blasting technique.

Jan 1, 2001

By Peter Bryant

"The case for innovation in the mining industry has never been more compelling—whether you believe the industry is in a sharp dip in a significant ‘sawtooth’ cycle or in the midst of a bust — the imperative is the same. Despite record production levels and still above-average prices compared to the lows of 2000, the industry is struggling to make profits and provide the returns on capital that investors are seeking. This represents a large-scale destruction of value over the last 15 years.The last 10 years have seen a sustained rise of operation expenses and capital development costs while there has been a rapid decline in productivity. This trend is unsustainable especially against other key structural challenges and forces shaping the future of the industry:1. Despite short-term fluctuations, there is longterm sustained demand for commodities.• Demand is driven by relentless urbanization, population growth and a rapidly growing middle class.2. Environmental concerns continue to mount.• Existing mining methods and their environmental footprint are becoming increasingly unacceptable to society.3. Geopolitical pressures and community activism are growing.• An estimated $25 billion worth of projects are on hold due to community activism.• Increasing nationalism tendencies and government expropriations of close to $30 billion.• Social license to operate is being challenged.4. Finding, building, operating and closing a mine just keeps getting harder and more expensive.• Costs have been increasing at an annual rate of 10 to 15 percent for the last 10 years.• More assets are stranded as they become uneconomical to mine under current mining methods, e.g. Olympic Dam.• Ore grades continue to decline.• Declining productivity at an annual rate of more than 10 percent for the last 10 years.5. The industry has consistently underinvested in technology and innovation."

Jan 1, 2015

By Jeremy Morris

The city of Indianapolis has more than 25,000 homes currently on septic systems. Many of these systems do not function well because of their age and surrounding soil conditions. As Indianapolis has worked to eliminate septic systems and install sanitary sewers in large unsewered areas on the north-west side, capacity of the existing Belmont North Interceptor (BNI) became a concern. The BNI system currently services an area of approximately 80 km2 (31 sq miles) located within the northwest quadrant of the city (Fig. 1). Monitoring of the existing interceptor indicated portions of the sys-tem flowing half- to two-thirds full during dry weather conditions and surcharging during some wet weather conditions. Further analysis of the BNI based on growth projections coupled with increased sewershed yield resulting from the city?s septic tank elimination program (STEP) indicated dry-weather flows could potentially triple over the next 20 years. Based on these modeling results and current wet weather capacity issues, the city determined further STEP projects could not be performed within the BNI service area until

Jan 1, 2011

By F. D. Fox

The Flambeau and Ridgeway Mines, both owned and operated by wholly owned subsidiaries of Kennecott Minerals Company, were located very close to populated areas having initial concerns about health, safety and the environment. The success of both operations depended upon developing a framework of community support and enhancing sustainable development opportunities throughout the entire life cycle of the mining operations to address these concerns. The protection of the Flambeau River was the cornerstone of the Flambeau Mine’s success. The highest priority for the Ridgeway Mine was to ensure long-term physical, chemical and ecological stability of the reclaimed mine site. Both of these goals have been achieved and are discussed in this paper, which highlights Kennecott Minerals Company’s integration of sustainable development principles into its business decision-making and management processes.

Jan 1, 2003

One of the biggest challenges for the mining industry is, quite literally, how to the keep the equipment rolling. There is a limited amount of companies that manufacture the 4.2-m- (14-ft-) tall, 5,670-kg (12,500-lb-) tires needed for the haul trucks that are approaching the 362 t (400 st) pay-load class, such as Terex?s MT6300-AC and Caterpillar?s 797F. And, while these might be the most impressive tires, they are not the only ones that are in short supply. The shortage of tires has affected just about every kind of machine, and the demand for those tires has been extremely high for more than five years with no end to the shortage in site. American Tire Corp. (www.americantire.us) is one of the companies working to supply tires to the mining industry. It announced that the demand for its 1.6-m (63-in.) tires that have a zero failure history globally is great and that the company signed contracts worth more than $500 million at MinExpo. A relatively new player in the field of large tires for mining equipment is Titan Tire Corp., (www.titan-intl.com), a subsidiary of Titan International Inc. It shipped its first 1.6 m (63 in.) off-the-

Jan 1, 2008

By David Smith

Construction of a new transportation link frequently requires crossing under an existing highway or railroad. Although traffic diversions may permit a cut and cover structure to be built, ‘zero impact’ tunnel solutions are becoming increasingly popular. The vertical clearance between the new tunnel structure and the existing highway or tracks may be very low; sometimes less than two meters. This leaves little room for error since any ground loss can rapidly translate into surface settlement. Problems can be avoided by maintaining the stability of the tunnel face and by minimizing ground movement around the tunnel lining. This paper examines construction methods that have been used to construct short tunnels with shallow cover, and highlights factors to be considered for future projects.

Jan 1, 2005

By Steve Kral

The mining industry is no stranger to hard times. Throughout its history, the industry has faced the ups and downs of commodity prices, difficult-to-mine-and-process ore bodies, labor issues and other problems. Throughout it all, though, the mining industry continues to provide the materials needed for society —even in the face of attacks by those who seek to cripple the industry or have it go away. The reason the mining industry survives, of course, is that mankind requires the products the industry produces. And, in recent decades, the industry has developed new technologies and improved on existing ones to produce those products in environmentally sound ways. At the same time, the economic benefits have been enormous to communities throughout the world where mining takes place.

Jan 1, 2002

A dedicated tunnel construction version of the Caterpillar 328D LCR compact radius excavator is proving highly productive on the A9 Autoroute construction project near Visp, in Switzerland. It is the first machine of its kind to operate on a Swiss contract and uses a special dedicated front attachment designed and constructed by German Caterpillar dealer Zeppelin. The machine offers a powerful, stable and compact solution for tunneling contractors. A rear overhang of just 305 mm (12 in.) provides a tail swing radius of just 1.9 m (6.2 ft). The 328D LCR is ideal for the restricted working areas within a tunnel construction site. The machine is equipped with the wide tracks from the 330D L conventional crawler excavator, ensuring maximum stability when operating. In addition, the boom mounting has been moved further toward the center of the machine for the tunnel model, creating an increased lift capacity over the front end compared with a standard 325D L. The boom itself features a robust box section construction, with high-strength steels, additional supporting struts and reinforced bearings for maximum durability. All pins have hard-chromium plating for optimum protection against wear. Stick digging force is a powerful 134 kN, with up to 212 kN of bucket digging force available, for maximum penetration in blasted material. The 328D LCR is also equipped with a heavy-duty dozer blade as standard. This ensures outstanding stability when working and providing a useful secondary tool for clearing and leveling within the jobsite. Two 45° tilting mechanisms in the boom construction, allow the boom to be swung to 45° on either side of the machine. So the specially designed attachment linkage provides increased rollback for access to the roof of the tunnel. A Caterpillar CW45S mechanical quick-coupler allows rapid changes between specialist tunneling attachments, standard Caterpillar buckets and a range of Caterpillar work tools. The machine is powered by a Caterpillar C7 diesel engine. This six-cylinder EU Stage IIIA diesel motor [ ] offers 8 percent more power than its predecessor, with 140 kW (190 hp) available at just 1,800 rpm. Caterpillar?s ACERT combustion technology results in lower fuel consumption and reduced exhaust emissions. However, the tunnel machine is also equipped with a diesel particulate filter as standard, to further cut exhaust gases within the tunnel working. The 328D LCR is designed for use in transport tunnels of 6.8 m (22.3 ft) in height. With the tunneling boom in place, the machine has an operating weight of 42,540 kg (93,783 lbs), yet retains a transport height with the tunnel boom of just 3.9 m (12.8 ft). Transport width with 600 mm (23.6 in.) track shoes, is just 3.2 m (10.5 ft). On the A9 tunnel contract, the machine is being used by a consortium of Swiss and Austrian companies working for the canton of Valais? Routes Nationals Construction (RNC) department. The 31.8-km (19.7-mile) A9 Autoroute construction project will connect Sierre in the west and the town of Brig to the east. The tunnel that is bypassing the town of Visp is just one of a number along the mountainous route.

Jan 1, 2009

By Desiree Willis

One of New York City?s largest subway projects is under way 43 m (140 ft) beneath the surface of downtown Manhattan. The East Side Access project, more than 30 years in the making, was halted after a partial excavation in the 1970s due to a lack of funding. The project, once dubbed the ?Tunnel to Nowhere,? has been revitalized into a groundbreaking subway line that includes unique tunnel boring machines (TBM), construction methods and muck removal systems. Project overview The East Side Access project involves construction of a new 6.7-km (4.2-mile) subway line needed to relieve heavy traffic congestion between the boroughs of Queens and Manhattan. The line will serve approximately 160,000 commuters daily between Grand Central and Sunnyside rail stations. Manhattan and Queens will be connected under the East River by the 63rd Street tunnel, a submersed double-decker tube. The submersed tube consists of reinforced concrete sections barged in place on the riverbed. The tube contains operational subway lines on the top deck, while the bottom deck (the ?Tunnel to Nowhere?) will become operational when the East Side Access project is completed in 2013.

Jan 1, 2008

By A. Wahab Khair, John G. Oldsen, John C. Stankus, Song Guo

During the last several years, implementation of trusses, in lieu of wood cribs, has been successful for supplemental tailgate support in the Pittsburgh seam. This paper reviews, the truss support system provided by the new high strength 0.6" tensioned cable truss, which is now also being used in cribless tailgates. Cable loading and roof deformation were monitored to evaluate roof and floor performance. The test results indicate that the cable truss system successfully controlled the roof and floor during the first and second panel extraction. This paper will describe the advantages of cable trusses and their load transfer mechanism as well as mine evaluation.

Feb 24, 1997

By Amanda Elioff

Success of the Gold Line Eastside Ex-tension rail tunnels in Los Angeles, CA has prompted the Los Angeles County Metropolitan Transportation Authority?s (Metro) planning new rail lines to include underground alternatives. The Westside Extension Transit Corridor alternatives include up to 27 km (17 miles) of subway to be constructed in soft ground. The routes will require construction in Los Angeles? ?potential methane zone,? which was not considered for subway construction until recently. Slurry face tunnel boring machines (TBM) will likely be specified.

Jan 1, 2009

By R. Steele

In addition to compliance with government emissions and reporting requirements, mining and mineral processing companies are increasing energy efficiency to reduce costs and become more competitive in the global marketplace. One of the major obstacles to identifying opportunities for increased energy efficiency is the lack of readily available data on energy use, and more importantly the energy use linked to production data, that identify energy reduction opportunities. As well as energy reduction, mining and mineral processing companies often struggle with the prediction of energy use, and are often penalized for under or over forecasting. Once again, it is the lack of timely information that makes this prediction difficult. This paper looks at expanding the use of a Manufacturing Execution Systems by integrating with Energy Solutions. This will provide automatic, timely information, at a granularity that makes it easier to identify energy reduction opportunities, reduce energy costs, and better predict energy use in a mining and mineral processing operation.

Jan 1, 2011

In Alaska?s southwest corner, in the Bristol Bay region, 476 holes have been drilled to help define the size of the Pebble Project. The results indicate that the deposit holds close to 32 Mt (72 billion lbs) of copper and 2.9 Gt (94 million oz) of gold. The Pebble Partnership, an Alaskan limited partnership of Anglo American and Northern Dynasty Minerals, owns the project that consists of two world-class mineral deposits. Currently in the prefeasibility and prepermitting stage of development, the Pebble Project is one of the largest and highest profile exploration projects in North America. History The Pebble West Project was originally discovered in 1988 by Cominco (now Teck Cominco). Drilling programs in 1997 defined a near-surface mineral deposit of 1 Gt (1.01 billion st). Minerals found included copper, gold and molybdenum. Northern Dynasty Minerals acquired the property in 2001 and, by 2005, it had confirmed a measured and indicated resource of 4.1 Gt (4.5 billion st) containing 1.2 kt (42.1 million oz) of gold, 11.2 Mt (24.7 billion lbs) of copper and 612 kt (1.35 billion lbs) of molybdenum and additional silver. By September 2005, Pebble East, a deeper, but richer deposit had been found. Drill data by the end of 2005 confirmed a 3.4-Gt (3.7-billion st) inferred resource containing 19 Mt (42.6 billion lbs) of copper, 1.2 Mt (39.6 million oz) of gold and 1.2 Mt (2.7 billion lbs) of molybdenum.

Jan 1, 2009

By J. C. Schneider, G. Van Weert

Hydrochem Developments Ltd. has developed and put into full scale operation a novel type of vertical flotation column incorporating a multiplicity of mechanically agitated stages. Characteristics of this flotation column include a low height to diameter ratio, high upgrading factors and the possibility of modifying geometry and operation to specific flotation requirements. A commercial unit is currently handling up to 100 tpd rougher concentrate at Dickenson Mines Limited, Balmertown, Ontario. Design parameters and plant performance will be discussed.

Jan 1, 1988

By Jeffrey A. Yonkey, Timothy J. Lutz, Jacob L. Carr, Christopher C. Jobes

"Since 1984, there have been 39 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM). In January 2015, the U.S. Mine Safety and Health Administration (MSHA) finalized a regulation to require proximity detection systems on all continuous mining machines except full-face machines (MSHA, 2015). Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHAapproved proximity detection systems are commercially available.NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system (Schiffbauer, 2002) and have recently conducted research intended to develop more advanced proximity detection technology for CMMs (DuCarme et al. 2013; Jobes et al. 2012; Carr, DuCarme et al. 2013 and Carr, Li et al. 2013). In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate (Li, Carr et al. 2013 and Li, Jobes et al. 2012) and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators (Carr et al. 2010 and Jobes, et al. 2012).To evaluate the performance of proximity detection systems implemented in industry, NIOSH researchers conducted tests in 2013 on three systems installed on CMMs at three underground mines in Illinois and West Virginia. The results of these tests indicated that, while generally consistent performance was observed, there were opportunities for improving performance. These results were presented at the 2014 SME Annual Meeting (Carr, Lutz, et al. 2014). Since that time, second-generation systems have become available to the industry and are becoming more commonly used.Beginning in early 2014, NIOSH researchers conducted underground testing of these secondgeneration proximity detection systems installed on CMMs. Five tests were conducted on four installations of second-generation proximity detection systems, with one installation being tested twice. The tests were conducted at mines located in Illinois, Virginia and Kentucky with seam heights ranging from 137 cm (54 in.) to 213 cm (84 in.). These tests were conducted using the same test protocol used during first-generation testing, which is summarized in the following section."

Jan 1, 2014

By J. B. Hadaway

The current limit to power transmission for grinding mills through one mill pinion is approximately 7,500kW. Above this power rating either twin pinion arrangements or Gearless drives are required. The SMTP concept was developed to overcome this limitation by using two pinions with a single large drive motor. The SMTP mill drive offers major advantages in capital cost and greatly simplifies plant layouts, while using an innovative adaptation of industry-proven single helical gearing. Through the use of a single motor, provision of variable speed drive is greatly simplified. The SMTP can also be used for significant power upgrades on existing mills.

Jan 1, 2001

By W. G. Pariseau

"The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to the start of mining in the south barrier pillar. Subsequent loss of ground control in August 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterward three rescue team members. A U.S. Mine Safety and Health Administration (MSHA)report describes the events in detail (MSHA, 2008).An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools and selecting the right tool for the job is essential. In this regard, minimum program requirements include capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses.The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two-dimensional finite element analysis indicated pillar safety was by no means assured (MSHA, 2008; Pariseau, 2008; Pariseau, 2011). Geometry of barrier pillar mining is limited in two dimensions for example, crosscuts are not seen in vertical cross sections. While three-dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three dimensions. This technique involves a dual node - dual mesh concept. Both have been used separately in much earlier work, but are only now used in combination. It is possible to have an estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale (Pariseau, 2014). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2014

By Kevin Andrews, Terry Hamric, Scott Nelson

"Mining conditions in underground coal mines are dictated by the environment in which the coal seams were geologically deposited. Depositional features can change rapidly, significantly affecting mining conditions. Mine geologists understand factors affecting mining conditions, predict future conditions, and provide guidance to mine management. A case study demonstrates how a mine in Appalachia merged an understanding of depositional environments with mining conditions and drilling data to make informed decisions as the mine encountered geologic anomalies. The assessment included drilling, mapping of geologic hazards and mine productivity, and creation of a conceptual depositional model. Metallurgical coal quality and clean tons per foot served as incentives for continued advance. Mining in the south was historically favorable, with good production and advance rates. As mining advanced north, changing geologic conditions caused the upper seam split to abruptly disappear. The mine ramped down into the lower seam split. Mining in the north area encountered unfavorable conditions, including transition roof, “horsebacks,” sandstone intrusions, roof rolls, and bony floor, resulting in low rates of mining advance. The mine geologist characterized the features and created a predictive model for future mining. Most of the adverse conditions were attributed to the coal in the north being part of an incised, transgressive valley fill environment, as compared to the favorable conditions in the south resulting from a floodplain depositional environment. Geologic conditions, low productivity, and unfavorable future predicted conditions in the north ultimately resulted in mine closure and reallocation of resources to a new mine with better forecasted conditions.INTRODUCTIONThe role of a geologist in assisting coal mining operations to understand and predict the impact of varying geological factors on mining productivity is a critical one, especially when management decisions must be made about the future prospects of a mine operating in difficult conditions. Chase, Newman, and Rusnak (2006) provide a very thorough discussion of the evolution of the role of the coal mine geologist and emphasizes the importance of understanding geology with regard to mine management decisions. Using actual mining performance data to determine which geologic factors are the most critical for mining is a powerful tool for making informed mine management decisions. For example, Nelson, Mullennex, and Miller (1988) provide a case study of analyzing the geologic factors impacting productivity of a Kentucky longwall mine to predict future mining conditions for the operation. In that case, the difficult geologic factors for longwall mining were prevalent across much of the remaining permit area and, in response, mine management converted the operation from a longwall operation to a continuous miner (CM) operation to better adapt to the geology. In another example, Keim and Miller (1999) evaluated geologic conditions impacting a West Virginia longwall mine. In both examples, significant geotechnical and geological information was available, including the opportunity to compare predicted mining conditions against actual conditions as mining progressed. Numerous examples of advanced Geologic Hazard Mapping (GHM) methodologies have come from government agencies and academia. For example, development of the Coal Mine Roof Rating (CMRR) system (Molinda and Mark, 1994) provided a standard means for geologists and engineers to communicate quantitatively with regard to mine roof conditions, and the introduction of the Stability Mapping System (SMS) provided an efficient means for analyzing numerous factors affecting coal mine stability (Wang and Heasley, 2005)."

Jan 1, 2019