Search Documents

By W Medina, G Angulo, A Anani

A current challenge faced by the mining industry is solving the integrated transition mine problem (TMP) that maximizes the net present value (NPV). This study aims to develop an optimization framework capable of solving the TMP. The problem is NP-hard and therefore computationally intractable. Three ad hoc approaches – Exact solution, Benders’ decomposition, and Benders’ decomposition with Bienstock-Zuckerberg (BZ) algorithm – are compared for different scheduling periods. The TMP is formulated as a mixed integer linear programming model, implemented in Python, and solved with the Gurobi optimizer. The results showed that Bender's decomposition with the BZ algorithm outperforms the other approaches in execution time, computational cost, and feasibility to address large problems in exchange for a marginal cost in the quality of the NPV obtained. In addition, the probability of finding the optimal point of transition is higher regardless of the number of feasible crown pillar locations evaluated. This is achieved through the optimality cuts proposed in the algorithm.

Jun 25, 2023

By Yiming Zhang, Yunpeng Li, Chun Feng, Ruyang Cao

In the past, the selection of the number of empty holes between blast holes heavily relied on the subjective experience of practitioners, leading to unsatisfactory blasting results. The number of empty holes between blast holes is particularly important for the perforation of explosive cracks. In order to determine the optimum number of empty holes for inducing the propagation of explosive cracks, a two-dimensional numerical model of two-hole blasting was established based on the continuous-discontinuous element method (CDEM) using polymethyl methacrylate (PMMA) as the medium, and numerical simulation of various working conditions was conducted; the simulation results are basically consistent with the PMMA model test. Through the analysis of blasting parameters, the optimal number of empty holes with a certain hole spacing is fitted. The following conclusions are drawn: (1) There is a threshold for variable x. When x exceeds 50, the presence of empty holes cannot lead to the perforation of explosive cracks between the blast holes. (2) When x is below 50, the optimal number of empty holes inducing the propagation of explosive cracks can be determined through fitting an empirical formula. By adjusting the number of empty holes between blast holes, a significant spacing between adjacent blast holes was achieved, allowing for effective penetration, so as to effectively “induce” the direction of the fracture zone and make full use of the energy of explosives. The research results of this paper are conducive to the research of directional blasting technology and provide certain references for the optimization of precision blasting parameters.

Dec 19, 2023

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

Belle Fourche Shale was processed and characterized for use as a clay-based ceramic. The shale was wet sieved to produce particles that were ± 150 μm. X-ray diffraction (XRD) revealed that the -150 μm material was enriched in clay content compared to the unprocessed materials, whereas the oversize material was enriched in quartz compared to the undersize sample. Particle size analysis was performed on the—150 μm sample, which showed that the median particle size was around 10 μm. Scanning electron microscopic (SEM) analysis further confirmed the small plate size, which appeared to be primarily layered clay particles. Next, the -150 μm particles were rolled into a green body, dried at room temperature, and fired at 998°C. The fired piece was analyzed by XRD and contained 6 wt% hematite, 55% quartz, 19% microcline, and various other minor amounts of minerals. When fired at 1152 ℃, mullite was found with increasing hematite compared to the 998 ℃ firing. A multi-spectral analyzer was used to quantify the color change of the 998 ℃ fired (orange) to the 1152 ℃ fired (red) samples. Micro-computed tomography (Micro-CT) of the unfired body exhibited very few large pores, while the piece fired at 998°C also exhibited few and small pores, the overall porosity of the fired body increased. Microhardness data, obtained from the aforementioned samples, resulted in Vickers Hardness (HV1.0) values of 70.8 HV1.0 (998 ℃) and 485.7 HV1.0 (1152 ℃). Three-point bend testing was performed, giving an average strength of 23 MPa on pieces fired at 998 ℃. The average bending strength of the samples fired at 1152 ℃, was 55 MPa.

Sep 26, 2023

By Laura Suarez, Jörgen Kajberg, Pär Jonsén

In recent years, slag, a residue from pyrometallurgical processes, has become more attractive in circular economy frameworks to increase the efficient use of resources throughout the life cycle of steel products and help in the reduction of carbon emissions. Its applicability is strongly dependent on the particle size, and therefore, the optimization of breaking processes should be approached by increasing the knowledge of the dynamics of slag to promote fracture. Increasing the knowledge on themechanical response ofmanganese slag opens up the potential for the development of cost-effective numerical models, e.g., constitutive models based on inverse engineering calibration frameworks or digital twins. In this study, rate-dependent tests of manganese slag have been performed using a split Hopkinson pressure bar device for testing its dynamic mechanical response. In order to obtain information about the crack initiation and fracture process, 2D ultra-high speed imaging was implemented with a sampling frequency of 663,200 fps for diametrically loaded specimens. Full-field deformation measurements using digital image correlation (DIC) techniques showed a staggered fracture process where failure points on mechanical response curves vary due to the internal events happening in the material. Localized frictional occurrences and inertial effects acting inside the pre-cracked matrix have a strong effect on the global mechanical response, and therefore, a great variability of strengths was obtained.

Nov 3, 2023

By M. Murphy

The multibillion dollar cost of cleaning up thousands of environmentally contaminated sites across the country created by decades of inadequate disposal of hazardous waste has led to a search for "deep-pocket" sources of cleanup funds. The resul1:: is the emergence of a growing body of law that could have a profound impact on commercial financing transactions and other investment activities when present or past owners of contaminated property are involved.

Jan 1, 1988

By Robin P. Gardner

The mechanistic approach to comminution consisting of incorporating particulate breakage functions into a suitable population balance equation has been developed by a number of researchers over the past decade or so. (1) To date this approach has been developed and demonstrated primarily for batch-operated, laboratory or small-scale ball mills. However, since industrial mills are mostly quite large and operated in the continuous mode; suitable population balance models and methods for obtaining the necessary breakage and other model parameters must be developed. This paper describes and investigates a radioisotope tracer technique for this purpose, Population balance models previously developed(2,3) are adapted for this study.

Jan 1, 1974

By Mirjana Boskovic

LKAB’s Kiirunavaara Mine is a sublevel caving iron-ore mine located above the polar circle in northern Sweden. The mine has been proclaimed seismically active since 2008 after a magnitude 3 seismic event, according to Swedish National Seismic Network (SNSN). At that time the Kiruna Mine did not have mine-wide seismic system. Since then, the Kiruna Mine experienced several damaging seismic events of which the largest one on the May 18, 2020. The magnitude, based on the moment tensor inversion results on data from the SNSN as well as seismic stations in Finland and Norway, is estimated to 4.2 ± 0.2 moment magnitude. The seismic event on the May 18, 2020 was located in the middle of the one of the productions areas and caused the major damage in the mine, damaging several kilometres of drifts on six mining levels, some of them beyond the practical repair. These damages affected four of ten production areas on several levels, some more some less. Luckily, no person got injured from the seismic event and the very long aftershock series. An important part in the whole process after the seismic event was information flow and decision-making process. It was very important to keep workers and community informed as that contributed transparency of decision-making and decreased the speculations. Resuming the production in the damaged areas in the safe manner, very soon become main focus for the mine management. It was obvious that not only rehabilitation of the areas is needed to resume the production. It was A MUST to understand the factors behind the seismic event and its mechanism to be able to avoid same situation and prevent seismic event of similar size. Mine engineers had to think outside the box to find the solutions to ‘rescue’ every drift that they could to be able to make good enough base for continued mining of the area. The paper describes actions taken in a very complex process of recovering the area that we from the beginning thought need to be abandon. Seismological analyses of the event on May 18, 2020 and past activity in the area, damage mapping, detailed studies of structures and geology, numerical modelling as well as engineering judgement were used as base for all our decisions how to proceed in attempt to restore mining of the area heavily damaged by 4.2 moment magnitude seismic event, in a safe way.

Apr 26, 2022

By Erika Moonin, Jim Nickerson, Claudio Cimiotti, Roberto Bono

"In response to the severe drought on the Colorado River basin and in order to preserve existing water capacity to the Las Vegas Valley, the Southern Nevada Water Authority contracted a new deep-water intake (Intake No. 3) located in Lake Mead. The current project (Contract No. 070F-01-C1) includes 5 km (3 miles) of tunnel with very difficult geological conditions and a 200- m (650-ft) deep shaft and marine works. This paper will present the current status of the design-build contract being constructed by Vegas Tunnel Constructors and the challenges and problems faced and the innovative solutions developed to handle the difficult conditions encountered during tunneling with up to 15 bars of pressure.ProjectbackgroundThe Las Vegas Valley receives the majority of its water from Lake Mead, which is located approximately 30 km (20 miles) east of the Las Vegas, NV metropolitan area. Due to the severe drought that has hit the southwest region of the United States, the water level in Lake Mead has receded from its high water level of 372 m (1,221 ft) above mean sea level (amsl) to a low of 330 m (1,076 ft) amsl in June 2015. Should the lake level continue to fall, at elevation 320 m (1,050 ft) amsl, the current water intakes will not be able to draw enough water to meet the needs of the local area. The risk of losing water capacity has prompted the construction of a new deeper intake. Not only is the new Intake No. 3 situated at a lower elevation in the lake at 262 m (860 ft) amsl, the new Intake No. 3 is also located to draw better quality (Fig. 1).Project challengesThe project has had several difficult challenges to overcome:• The work consisted of a 1.2 kt (1,300 st) structure constructed on a barge and lowered 100 m (330 ft) into Lake Mead anchored with 9,200 m3 (12,200 cu yd) of tremie concrete.• The drill-and-blast starter tunnel was impacted by three inflow events, resulting in a one-year project delay.• One of the main challenges was selecting the tunnel boring machine (TBM) and excavating the tunnel with expected hydraulic head pressure of as much as 17 bar (16 bar was the highest pressure recorded during the drive), crossing faulted areas, low rock cover and the risk of tunnel instability due to direct connection with the lake.• Extensive pre-excavation grouting with a constant head pressure ranging from 12 bar to 15 bar.• Structural repair of the cutterhead in difficult hydrogeological conditions [water inflow of approx. 800 m3/hr (4,000 gpm)].• Complete repair of the cascade sealing system for the main bearing and two replacements of the pinion bearings.• The TBM approach to the intake structure."

Jan 1, 2015

"One of the major issues that the Rare Earth Elements Mining Industry has to deal with is the legislation vacuum that exists in many countries around the world. Among these, are countries which have long history and tradition in mining. In many cases the lack of direct legislation for REE mine management as well as for other potentially polluting industries can be a barrier to sustainable development. Moreover, the case of lax legislation in China has led to environmental pollution problems and extended smuggling of rare earth elements. This paper looks into the current regulatory status on the mining of REEs, identifies the loopholes and suggests some elements for a new global legislation framework for sustainable development in the REE mining industry. The setting of this regulatory framework will be in line with the present and future challenges of the rare earths market as well as with the policy strategies that are defined internationally. The aim of such a legislative framework will be to strengthen the global rare earth elements supply chain, appease social concerns and ensure the preservation and conservation of the environment. INTRODUCTION The general public received their first introduction to rare earth elements (REEs) in 2010, when the previously inconspicuous commodities became the subjects of front-page headlines. It was when China created a furore in global high-tech markets after imposing an embargo on Japan following a minor marine dispute (Barakos et al. 2015b). Soon enough the Chinese embargo was extended on REE export restrictions all over the world and thus aroused concerns to many countries over potential supply disruptions. The world had suddenly realized that these wonder materials underpin products that they care about. Governmental and industry executives, policymakers and material scientists voiced concerns and conducted numerous reports stating the situation and the risks of a supply crisis. The price spike of 2011 intensified the crisis and the public turmoil, yet the drama did not last for long as the prices declined significantly in 2012. Nevertheless, the world was nonplussed by the fact that China has the total control of the market with more or less the 90% of the global production. More potential entrants became interested, thus initiating an exploration boom during the recent years that has resulted in a significant increase in known global REE reserves that could have potentials for exploitation."

Jan 1, 2016

By A. Cecala, J. Noll, J. Hummer

The National Institute for Occupational Safety and Health has observed that many control rooms and operator compartments in the U.S. mining industry do not have filtration systems capable of maintaining low dust concentrations in these areas. In this study at a mineral processing plant, to reduce respirable dust concentrations in a control room that had no cleaning system for intake air, a filtration and pressurization system originally designed for enclosed cabs was modified and installed. This system was composed of two filtering units: one to filter outside air and one to filter and recirculate the air inside the control room. Eighty-seven percent of submicrometer particles were reduced by the system under static conditions. This means that greater than 87 percent of respirable dust particles should be reduced as the particle-size distribution of respirable dust particles is greater than that of submicrometer particles, and filtration systems usually are more efficient in capturing the larger particles. A positive pressure near 0.02 inches of water gauge was produced, which is an important component of an effective system and minimizes the entry of particles, such as dust, into the room. The intake airflow was around 118 cfm, greater than the airflow suggested by the American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ASHRAE) for acceptable indoor air quality. After one year, the loading of the filter caused the airflow to decrease to 80 cfm, which still produces acceptable indoor air quality. Due to the loading of the filters, the reduction efficiency for submicrometer particles under static conditions increased to 94 percent from 87 percent.

Jan 1, 2015

By J. Christophe Niyonzima, Ekata Emmanuel Edo, Sayaf Mustafa, Liqun Luo

Iron and manganese both are important ferrous metals, and they usually need to be extracted separately for better usage. Ferromanganese ore from the Yunnan Province of China was investigated by subjecting it to reduction roasting, leaching, magnetic separation, hydrometallurgical separation process, X-ray diffraction (XRD), electron probe micro-analysis (EPMA) and scanning electron microscopy/energy-dispersive spectroscopy (SEM-EDS). It is noted that the ferromanganese ore contains valuable components or elements of 21.41 wt%Fe2O3 and 19.88 wt%MnO, which are 14.99% and 15.40% of the total of Fe and Mn, respectively, with a large amount of impurities comprising 33.00 wt% SiO2, 9.81%wt%Al2O3, etc. After roasting, microscopic examination showed the presence of haematite, magnetite, pyrolusite, psilomelane, hollandite, marcasite, pyrite, limonite, braunite and manganite, while XRD analysis showed that the magnetite content increases with the increase in roasting temperature, reflecting the increase in conversion of haematite to magnetite. Based on EPMAand SEM-EDS analysis, it was shown that the haematite and magnetite interface were the main Fe-bearing minerals; however, the dissemination of the two minerals, that is, haematite andmagnetite with the coexistence of Fe- and Mn-bearing minerals, will result in difficulty in effective separation of Fe and Mn. The effective roasting temperature and roasting time were 800 °C and 60 min, respectively, to avoid the formation of a composite oxide of MnxFe3-xO4 beyond 800 °C. The Fe recovery via roasting and magnetic separation only was 66.56%, whereas a combination of magnetic separation which ensued after the leaching process showed a recovery of 80.08% and 59.95% of Fe and Mn, respectively.

Mar 26, 2021

By Sandeep Kumar Asarapalli, Sunil Kumar Bisoyi, Bhatu Kumar Pal

Spontaneous heating of coal is one of the major concerns in the coal mining industry. Hundreds of millions of tons of coal are lost each year because of spontaneous heating. If necessary arrangements are made, many fires due to spontaneous heating may be avoided. Therefore, protective measures have become essential to prevent coal from spontaneous combustion. A large amount of coal reserve can be saved by the assessment, suppression, and prediction of spontaneous heating of coal, which also helps in betterment and efficient coal production. The use of chemical retardants can act as inhibitors for the liability of coal toward spontaneous heating by increasing its ignition temperature, thereby, increasing its incubation period. The coal-chemical mixture can be used for whitewashing the exposed coal in galleries as it creates a layer between coal and oxygen in the atmosphere, delaying the oxidation process and ultimately inhibiting the spontaneous heating liability of coal. This work examines the effect of chemicals such as sodium chloride, calcium carbonate, potassium iodide, sodium nitrate, and potassium chloride on the spontaneous heating of a coal sample. Thereby, it suggests a better chemical for inhibiting the liability of coal toward spontaneous heating. The experimentation involves flammability temperature (FT), crossing point temperature (CPT), and differential thermal analysis (DTA). The ignition and oxidation temperatures were found from the above experimental methods for Lingaraj open-cast coal mine samples, with and without adding chemicals. The results are cross-checked and verified through DTA. Correlation analysis was carried out among the results obtained from CPT, DTA, and FT, and better chemical retardants that effectively inhibit coal’s tendency toward spontaneous heating were suggested.

Dec 23, 2023

By M. Moats

Copper electrowinning operations have dramatically improved their ability to produce high quality copper at low costs over the past several decades. Even so, some fundamental knowledge is still lacking that could allow operations to run even more efficiently. For example, a rule of thumb exists that estimates a current efficiency loss of 2-3% per gram per liter of iron in the electrolyte. While several laboratory studies have been performed that demonstrate this rule of thumb is likely true, no definitive relationship exists. In this paper, the first steps in developing a definitive relationship are presented. The effective diffusivity of ferric ions in synthetic copper electrowinning solutions was measured using chronoamperometry and the Cottrell equation. The effective diffusivity of ferric ion was determined as a function of electrolyte concentration and temperature. Synthetic electrolytes were then used in laboratory-scaled copper electrowinning experiments, where relationships between current efficiency and solution composition were found to exist under stagnant conditions. Key words: Copper electrowinning, Current efficiency, Chronoamperometry, Ferric ions

Jan 1, 2009

By E. Siami-Irdemoosa, S. R. Dindarloo

"Discrete event simulation is a stochastic mathematical modeling tool with applications in queuing systems. Many mining operations, both surface and underground, can be simulated in the context of queuing theory , for example open pit loading and haulage operation, underground level and vertical transportation, and mineral processing circuits. A computer simulation model of the operation is an invaluable tool to study both the system’s dynamics and conducting sensitivity analysis on different effective elements on system performance. In this paper, merits of discrete event simulation in decision making in mining engineering is discussed. Moreover, a stochastic simulation framework for selection and sizing of shovels and dump trucks in surface mining is presented to elaborate one example for applicability of the method in mining operations. INTRODUCTION Mathematical modeling is a valuable tool in design, optimization, and decision making in both surface and underground mining operations. Several researchers have tried to study different aspects of mining operations using a wide range of mathematical techniques such as linear programming[1], analytical hierarchy process [2], non-linear programming[3], genetic algorithms[4-5] ,mixed integer programming [6], machine repair model[7], queuing theory [8], and conventional spreadsheet calculations based on experience and engineering judgments. There are different uncertainties in typical mining operations (e.g. material loading and haulage, drilling, and blasting). For example, in a truck-shovel operation, different governing activities such as loading, haulage, and dumping cycles are stochastic variables. Moreover, analytical modeling of a large truck-shovel operation is very complicated. Thus, application of analytical and/or deterministic techniques cannot guarantee a solution for different problems that are encountered in daily mining operations. Discrete-event system simulation (DES) is a modeling method for such time discrete and probabilistic phenomena [9]. DES has been employed by different researchers in mining engineering through available software and languages such as GPSS, SIMAN- ARENA, and SLAM [10-14]. Most of the studies so far, tried to evaluate some “what-if” scenarios, to understand the possible effects of changing different input variables on overall mine economics. For instance, Baffi and Ataeepur (1996) used Arena to simulate a truck-shovel operation [10]. Also, Sturgul has conducted extensive studies in the application of DES in the mining engineering field [15- 17]. A very good background review of application of this technique in the industry can be found in [15-16]. Previous studies have shown that, different approaches including deterministic, stochastic, and experimental methodologies result in considerable differences in outputs [18]. These techniques lead to different solutions, regardless of the quality of technique/software itself or knowledge of the modeling team. Hence, the first step is to develop a comprehensive simulation framework to obtain nearly the same optimal results for the same input variables, regardless of the employed technique."

Jan 1, 2016

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

This study developed machine learning (ML) models for predicting rock formation reactive forces experienced by a hydraulic shovel bucket during excavation. To do this, rock formation in the form of muckpile was modeled as granular ball elements in three-dimensional particle flow code (PFC) using linear bonding logic. A typical field-size hydraulic shovel bucket modelled in AutoCAD was used to excavate the rock formation and the three-dimensional shovel bucket resistive forces required to cut through the rock formation were measured and recorded. The experiments involved different muckpile height, bulk densities, repose angles, and average fragment size. Six ML algorithms, artificial neural network (ANN), K-nearest neighbor (KNN), linear, random forest (RF), regression tree (RT), and support vector machine (SVM), were evaluated on their ability to predict the shovel bucket resistive forces. The input variables used for the prediction of the resistive forces were the muckpile bulk density, angle of repose, height, and fragment size. The results showed that the ML techniques are useful and reliable methods of predicting rock formation resistive forces based on the rock formation properties. This research is a preliminary step towards developing reliable models for accurate prediction of excavation forces/torques which could potentially enhance hydraulic shovel process automation.

Sep 27, 2021

By J. C. Watts

Monitoring and control of conventional industrial wet grinding circuits is conceptually straightforward. However, since production objectives and operating constraints can vary widely from plant to plant, there is probably no single overall grinding circuit control strategy which is "best" in all cases; in-variably some compromise is necessary between performance desired under ideal conditions and performance achievable in practice. The recent advent of relatively low cost, reliable, high speed small computer systems is revolutionizing daily operations in increasing numbers of metallurgical processing plants. Of special power and capability is a hierarchical computer network like that currently in use at the Pinto Valley Operations of the Cities Service Company. Several satellite processors for key plant areas communicate with a master computer operating under a powerful multitasking real-time operating system. Hardware and software structure is such that downtime on one of the processors -including the master -does not have a major impact on overall system operation. Admittedly, the powerful, core efficient table driven satellite software, which handles process/computer communication, calculation of nonmeasured process variables, and basic Direct Digital Control functions, is difficult to modify. However, important high level process monitoring, report preparation, graphic display, and supervisory control functions -including economic optimization -can be implemented by project engineers at the plant site. Thus, for example, new control strategies can be quickly examined and rapidly evaluated. Such computer monitoring capability also permits use of short duration process pulse tests for approximate dynamic modeling and rapid calculation of controller tuning constants for single loop dominant systems. Following a brief back-ground discussion of the Pinto Valley Project, we present some of the more interesting results and conclusions of our work over the past year.

Jan 1, 1978

By Kallam V. K. Reddy, VADAPALLI SANJANA, Veerendra Singh, Gajanan Kapure

This work describes a leaching process for the conversion of high-magnesium peridotite rock, which is a chromite ore overburden, into two valuable products: magnesium salts and micro silica. Under normal leaching conditions, residue remaining after leaching is of a gelatinous nature and thus hinders the filtration process. To address this issue, oxidative leaching with the addition of H2O2 was employed, and it significantly improved the filtration kinetics. Four different approaches for H2O2 addition were tried, and they all proved effective in controlling gelation. The optimum oxidative leaching condition was 70 °C, 2 h time, 2 M H2SO4, 0.5MH2O2 and 400 RPM; under these conditions, 92% magnesium leaching efficiency was achieved. After leaching, the leach liquor obtained was purified and dried into Mg(OH)2 and MgSO4 salts. The leach residue contained mainly silica particles, with size in the 10–30 μm range. This material thus represents an attractive candidate for the production of highperformance concrete for the construction industry. The oxidative leaching process described here enabled the complete conversion of peridotite into valuable products, magnesium salts and micro silica.

May 5, 2020

By Fengmei Chen, Na Liu, Bingrui Li

A quantitative analysis method based on the airflow influence factors is proposed to evaluate airflow stability and discriminate airflow directions in complex ventilation networks. The law governing the changes in airflow caused by changes in branch resistance is revealed based on simulations of the airflow state in a ventilation network and a statistical analysis of the results. Then, three evaluation indices (airflow sensitivity, airflow influence factor, and critical airflow) are determined, matrices of the airflow influence factors and critical airflows are constructed, and a quantitative evaluation method for ventilation system stability and an airflow directional discriminant are proposed. The results show that the stability of a ventilation system can be reliably evaluated based on the airflow influence factors. The sensitive branches and dominant branches in the ventilation network can be determined based on the matrix of airflow influence factors, and the reversed branches, the trigger branches, and the reversal conditions can be determined based on the critical airflow matrix and the matrix of airflow influence factors. The proposed airflow directional discriminant is suitable for evaluating arbitrarily complex networks.

Nov 15, 2023

By Michael Murphy, Gamal Rashed, Brent Slaker

Pillar stability continues to be a significant concern in multiple-level mining conditions, particularly for deep mines when pillars are not stacked or the thickness of interburden between mining levels is thin. The National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to investigate the stability of pillars in multiple-level limestone mines. In this study, FLAC3D models were created to investigate the effect of interburden thickness, the degree of pillar offset between mining levels, and in situ stress conditions on pillar stability at various depths of cover. The FLAC3D models were validated through in situ monitoring that was conducted at a multiple-level stone mine. The critical interburden thickness required to minimize the interaction between the mining levels on top-level pillar stability was explored, where the top level mine was developed first followed by the bottom level mine. The model results showed that there is an interaction between numerous factors that control the stability of pillars in multiple- level conditions. A combination of these factors may lead to various degrees of pillar instabilities. The highest degree of local pillar instability occurred when pillar overlap ranges between 10 and 70%. On the contrary, the highest degree of stability occurs when the pillars are stacked, the underlying assumption is that the interburden between mining levels is elastic (never fails). Generally, for depths of cover investigated in this study, the stability of top-level pillars shallower than 100 m (328 ft) or with interburden thicknesses greater than 1.33 times the roof span—16 m (52.4 ft) in this study—does not appear significantly impacted by pillar offset. The results of this study improve understanding of multiple-level interactions and advances the ultimate goal of reducing the risk of pillar instability in underground stone mines.

Jul 27, 2022

By M. Fan, Z. Long

"This paper presents some studies on recovering valuable elements from Chinese coal by-products, including coal combustion fly ash, stone coal ash, and coal flotation tailings. Both commercialized technologies and economic potential recovery methods are described in this study. Magnetically stabilized air-dense medium fluidized bed separation, tribo-electrostatic separation, froth flotation, and hydrometallurgical methods are discussed in recovering various valuable elements in Chinese coal by-products from different coalfields. These valuable elements include iron, carbon, aluminum, rare earth elements, lithium, gallium, germanium, uranium, titanium, scandium, silicon, vanadium and phosphorus, etc. The ultimate goal is to fully utilize all valuable elements in coal by-product. Each component within coal by-product should be efficiently segregated to its highest value. INTRODUCTION Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium, and phosphorus, etc. These coal-associated elements are significantly enriched in coal combustion by-product fly ash because of majority of main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main elements oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China, and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary widely due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides, and unburned carbon."

Jan 1, 2017