Search Documents

By C. Strachan

This paper presents an evaluation of tailings dam incidents from the 1994 USCOLD Tailings Dam Committee report. Comparisons are also made with water storage dam incidents from USCOLD reports and recent tailings dam incidents. The evaluation results show that tailings dam incidents are due to a number of factors including overtopping, static and seismic instability, seepage and internal erosion, and foundation conditions, and that no particular type of tailings dam or operational condition is more susceptible to incidents. In addition, the results confirm that tailings dams should be located, designed, operated, and reclaimed with a thorough knowledge of site conditions, mill operation, site monitoring, and tailings characteristics.

Jan 1, 1999

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

By C. L. Jiang, B. K. Parekh, X. Shao

Among the impurities present in phosphate ore, dolomite is the most difficult to remove. This is because dolomite and phosphate have similar chemical compositions and because the dissolved species of dolomite is adsorbed on the surface of the phosphate mineral. A new amphoteric surfactant was found to be a suitable collector for the separation of dolomite and phosphate. Flotation results showed that the new amphoteric collector had a high flotation selectivity for dolomite over a wide pH range. studies on the flotation of francolite and dolomite in each other's supernatant demonstrated that the dissolved ions had little effect on the selectivity of the new collector. It was found, however, that the dissolved ions were detrimental to the flotation separation using sodium oleate as collector. From a mixture offrancolite and dolomite containing 26.2% P2O5, a phosphate concentrate containing 35.2% P205 with a 90% recovery was obtained using 290 g/t of the amphoteric collector. The rejection of MgO was 81.41 %.

Jan 1, 1999

By Jr. Babcock

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd., in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain Ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 kilometers. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fibre in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd. Of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This paper will present the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits will be outlined. Subsequent work by other companies will be mentioned, but not described in any detail. This subsequent work did not alter Kennecott's conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd., who have been involved in the project, particularly Ramon Farmer, N. G. Comer, and A. W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this report are solely that of the author and result from his involvement in discovery of the deposits and management of the exploration program.

Jan 1, 1978

By H. Y. Sohn

Considering the two most important issues the ironmaking industry faces today, i.e., energy consumption and greenhouse gas emissions, it would be advantageous to utilize the concentrate-size raw materials directly without pelletizing or sintering, especially without the use of coke. This plenary lecture describes two such processes developed at the University of Utah. One is the Flash Ironmaking Technology (FIT) and the other is a moving-bed process for continuous ironmaking with gaseous reduction of iron ore concentrate (MBIT). These technologies are designed to produce iron directly from iron concentrate without requiring pelletization/sintering and cokemaking in two significantly different temperature ranges. They take advantage of the high reactivity of the concentrate particles and will considerably reduce energy consumption and carbon dioxide emissions compared with the current processes. The process of the development from the conception of the idea, to kinetic feasibility establishment, to laboratory flash furnace, and finally to the operation of a prototype facility for the development of the FIT is discussed. The development of the MBIT also started with the formulation of the process concept, followed by kinetics feasibility establishment, and the design of a potential industrial reactor. The results of economic analyses on the FIT are briefly described.

May 12, 2023

By N. Chow

The recovery of manganese from lower grade resources has been studied for a number of years. Of key importance of prior work, was the discovery that higher valent manganese resource can be readily leached with sulfurous acid. This eliminates the need for high temperature reduction roasting that is conventionally used in processing high grade material. High temperature roasting is energy intensive, emits a large amount of carbon dioxide, and would not be economical for processing lower grade material. While the prior work provides important information to extract manganese from lower grade resources, the production of unwanted by-products, and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems, which to this point preclude commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low cost, environmentally friendly manner. Emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted by-products.

Jan 1, 2011

By H. Gurgenli

Mining companies require accurate short-term mining forecasts to meet budget targets and customer needs. Challenging mining conditions along with employee turnover and lack of standard geologic modeling and mine planning processes can result in time-consuming and inconsistent mine plans. Documentation and automation of the processes involved in mine planning, as well as proper software utilization, are critical in overcoming these challenges. This paper discusses the steps involved in achieving an optimized mine planning system to accomplish productive and cost effective operations. In addition, a case study is included to describe the process of implementing a semi-automated system whereby the geologic model and mine scheduling database are updated monthly to incorporate changes in geology in a relatively complex open-pit coal mine. This case study proves that the ability to update geologic models based on the latest information gathered from production drilling and mining activities can greatly enhance the ability to accurately predict short-term mining production.

Jan 1, 2011

By H. E. Cross

In a minerals-recovery context, the object of exercising control over milling operations must be threefold, 1) To achieve maximum recovery at 2) minimum operating costs and 3) making maximum use of installed equipment, Milling is one of a sequence of operations which have as their objective the economic recovery of minerals from mined ores, All operations in the sequence are interdependent and each is both influenced by and itself affects all other unit processes. The part which grinding plays in achieving each of the above objectives is indicated in the following analysis: In South Africa, the most important mining operations are still the gold mines, A vast reservoir of knowledge and experience in treating the Witwatersrand and associated ores has been accumulated. and recoveries are consistently high, However residue values do vary and frequently this is due to fluctuations in the degree of grind, The significance of changes in residue values is indicated by the following example: On a modern mine, the residue values varied from 0,25 to 0,33 dwi; per 2000 lb, during a period of 6 months, The cash value of the gold thus lost varied therefore between $0.44 and $0.58 per 2000 lb, ton. A residue which assays 0.30 dwt per ton would contain approximately 0.26 dwt as undissolved gold and 0,040 dwt per ton as dissolved gold present in residual solution after filtration. This dissolved gold loss is a function of efficiency of filtration and varies from 0.030 to 0,.070 dwt per ton of residue.

Jan 1, 1970

By J. Pesl, R. Hurman Eric

Metal-slag phase compositions of molten iron and ilmenite smelting slags or solid titanate phases were determined between 1500° and 1700°C. The influence of oxygen partial pressure and impurity oxide additions including Al2O3, Cr2O3, MgO and SiO2 were investigated along with amount of reductant-carbon. The XRD revealed that the quenched slag crystallized as pseudobrookite (M3O5) solid solution in equilibrium with iron. Silica additions formed separate silicate phases because of its immiscibility in the titanate phase. Under strong reducing conditions iron oxide was almost completely reduced and the slag phase solidified as a consequence thereof. Cr2O3. SiO2 and MnO were also reduced to a high degree. Under weak reducing conditions the slag was fully molten and non of the impurity oxides were reduced. A significant portion of manganese, some magnesia and silicon, in the form of SiO gas, were removed via the gas phase due to their considerable vapour pressures. Alumina was not reduced under the applied conditions. A comparison of the experimental results with industrial data clearly suggested that industrial ilmenite smelting process operated under non-equilibrium conditions.

Jan 1, 2005

By James M. Harrington, A. Azra Bilgin, JoAnn Silverstein

The prevention of AMD in situ is more attractive compared to subsequent downgradient treatment alternatives that do not involve source control. AMD source control can be achieved by shifting the microbial activity in the sulfidic rock from pyrite oxidation to anaerobic heterotrophic activity. This is achieved by adding biodegradable organic carbon amendments to the sulfidic rock. This technique was applied in an abandoned mine pool with a pH of 3-3.5. Following treatment, near-neutral pH and decreased effluent heavy metal concentrations were achieved. In situ bioremediation by enhancement of bacterial iron and sulfate reduction is a promising technology for AMD prevention.

Jan 1, 2005

By Michelle L. Ramos

INTRODUCTION The Ballard Siphon was built in 1935 and consists of two 91.4 cm (36-inch) diameter wood-stave pipes. These pipes convey sewer flowsunder the Ship Canal from northwest Seattle and the Ballard Regulator to the North Interceptor and the West Point Treatment plant. The siphons were constructed using open cut construction, are now buried in the sediment on the floor of the canal, and have severely limited ability to be dewatered, inspected, or cleaned. The existing siphon is 394.7 m (1,295 feet) long from the junction structure on the southern shoreline to the regulator structure on the north. The location of the Ballard Siphon is shown in Figures 1 and 2. The area around the Ballard Siphon has become more populated and developed since the siphon was built. Additionally, the Ballard Siphon is subject to high flows that are greater than the capacity of the pipelines. This has resulted in predict-able Combined Sewer Overflows(CSO?s) whenever a large, long duration rain event occurs. The aged pipeline of uncertain viability has become a critical piece of the sewer system infrastructure. Because of the age of the pipelines and their importance, a sonar survey was completed on both barrels of the Ballard Siphon in December of 2005. The sonar images appeared to indicate crown intrusion of the wood-stave pipes, which suggested that the pipes were in imminent danger of collapse. As a result, an Emergency Declaration was executed by King County and the Ballard Siphon Replacement Project was initiated. Staheli Trenchless Consultants was retained to perform feasibility studies to deter-mine the viability of using microtunneling and horizontal directional drilling (HDD) for replacement of the Ballard Siphon. For the evaluations, the preferred site location was determined to be at or near the site of the existing Ballard Siphon in order to minimize the ancillary sewer work which would accompany moving to a new site. To meet flow demands and hydraulic requirements, the replacement siphon needed a mini-mum equivalent diameter of 182.9 cm (72 inches). This could be accomplished with a number of different siphon diameters and configurations including, but not limited to, three 106.7 cm (42-inch) diameter pipelines, two 152.4 cm (60-inch) pipelines, or two 91.44 cm (36-inch) pipelines and a 121.9 cm (48-inch) pipeline.

By W. Burger

Mechanical excavation methods can significantly improve excavation performance and labor safety compared to drill and blast operations. Herrenknecht has developed a mechanized shaft sinking method for soft and medium strength rock. This system combines innovative technologies which allow simultaneous excavation, removal of cut material and the installation of rock support. This Shaft Boring Roadheader ?SBR? is flexible in diameter and can be used in shafts with changing diameters and different shaft support requirements for depth up to 2,000 m. During regular excavation personnel are not required to access or work on the shaft bench. The boom used to cut the shaft profile is based on roadheader technology.

Jan 1, 2012

By Augustine O. Orumwense

Ball mills are commonly used for regrinding operations in the mineral processing industry. But, in recent times, efforts are being made at the introduction of stirred mills particularly for those instances where very fine grinding is required. Media type (steel shot, glass beads, alumina balls and crushed quartz), media size, mill speed and the number of passes required to obtained the target product size are studied. The product size and energy consumption are used in the evaluation of the test results. The grinding media size, shape, density, filling ratio, mill circumferential speed and grinding time play a distinct role in product size fineness.

Jan 1, 2005

By E. Giama, A. Macridis, A. M. Papadopoulos

ISO 14031 is an international standard that describes a process for measuring environmental performance evaluation by setting quantitative indicators and providing a structured approach for organizations to follow, independent of location, size, complexity and type of activity. It is not a standard for certification as ISO 14001 is, but it fits into the ISO 14000 series of standards and is intended to assist organizations to apply environmental management systems and obtain environmental evaluation. This case study’s main objective is to identify the interaction between ISO 14031 and ISO 14040-42. ISO 14040-42 is referring to Life Cycle Analysis (LCA) methodology. More specific, LCA is applied (based on the ISO 14040-42 standard) to stone wool’s production, the market dominating thermal insulation material, produced by bauxite and amphibolite. LCA is used as a decision making tool for the development of environmental indicators (based on ISO 14031 guidelines) and for environmental performance evaluation.

Jan 1, 2005

By W. Blake, J. Whyatt

Sixty years of rock bursting in the Coeur d'Alene district has taught painful lessons and led to a number of practical advances in controlling rock-burst hazards. This paper summarizes these lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rock-burst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rock-burst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d'Alene district experience.

Jan 1, 2003

By M. Ahrens

Gearless mill drives (GMD) are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as the development and the progress of GMD systems over the years. With an increasing installed base and many drives operating for many years, there is an increasing need to modernize or revamp existing GMD installations. The first installations of GMD took place in the cement industry and have demonstrated that ringmotors can achieve a lifetime well above 40 years, if maintained properly. The life cycle time of many other components, especially electronic parts, is usually shorter. It is therefore necessary to replace aged or out-dated components early enough in a planned manner in order to reduce the risk of component failures and the related shutdown times. Modernization upgrades can range from minor software updates to a revamp of the cycloconverter. The paper describes typical examples of such upgrades and shows the most important aspects that need to be considered.

Jan 1, 2008

By Franz Walchshofer, Mark Kuchta, Nobuharu Isago, Ugur Ozbay, Wolfgang Dolsak

A series of in situ pull test were performed on a new design friction stabilizer bolt with the objective of determining its performance characteristics. The bolt is installed while drilling, thus improving safety and significantly reducing the installation time. An optional expansion element can be inserted into the bolt to provide an end-anchorage, which further increases the bolt’s capacity. In situ tests show that the pull capacity of the 2 m long new design bolt is about 15 tons. When installed with an expansion element, the pull capacity of these bolts becomes as high as 30 tons.

Jan 1, 2005

By C. S. Todd, R. L. McNearny, S. Dun, P. Clark, P. W. Conrad, X. Liu, J. Q. Wu, H. Rhee, W. J. Elliot

Soil erosion is strongly related to soil hydraulic properties. Understanding how surface coal mining affects these properties is therefore important in developing effective management practices to control erosion during reclamation. To determine the impact of mining activities on soil hydraulic properties, soils from undisturbed areas, areas of roughly graded mine spoil, areas with replaced topsoil before seeding, and revegetated areas at the Rosebud Mine in Eastern Montana were evaluated. Field and laboratory studies were conducted to determine the soil hydraulic properties of the four representative areas, including particle-size distribution, organic matter content and saturated hydraulic conductivity. Using this data, Water Erosion Prediction Project (WEPP) simulations and risk analyses were performed to investigate mining’s effects on changes in soil erosion potential. Significant differences were seen in the hydraulic properties of the soils in the representative areas due to the mining and reclamation practices at the mine. The WEPP simulations show that the potential for soil erosion increases as a result of mining activities disturbing the soil. The simulations also indicate that the erosion potential may return to pre-mining levels over time with effective revegetation practices.

Jan 1, 2015

By Jon A. Hummer, Aleksandar D. Bugarski, Shawn Vanderslice, Teresa Barone

A study was conducted to examine the potential of diesel emissions control strategies based on retrofitting existing power packages with exhaust aftertreatment devices and repowering with advanced power packages. The retrofit systems, a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF), were evaluated individually using a US EPA tier 2 (ter 2) engine operated under four steady-state conditions and one transient cycle. The DOC effectively curtailed emissions of CO, and to some extent organic carbon (OC), elemental carbon (EC), and aerosol number concentration. The DPF system offered substantially higher reductions in OC and EC mass and aerosol number concentrations. Both, the DOC and DPF achieved reductions in the aforementioned emissions without adversely affecting emissions of NO2 and nano-sized aerosols. The strategy of repowering with an advanced system was examined using a US EPA tier 4 final (tier 4f) engine equipped with a cooled exhaust gas recirculation system and diesel exhaust fluid-based selective catalytic reduction system, but not with a DPF system. The tier 4f engine contributed substantially less than the tier 2 engine to the EC and OC mass, aerosol number, and CO, NO, and NO2 concentrations. The tier 4f engine was very effective in reducing aerosol mass, NO, and NO2 concentrations, but it was not equally effective in reducing aerosol number concentrations. The implementation of viable exhaust after treatment systems and advanced diesel power packages could be instrumental to the underground mining industry to secure a clean, economical, and dependable source of power for mobile equipment.

By J. A. Herbst

Fine coal cleaning by froth flotation has become common practice in the U.S. with more than 80,000 tons treated in this way per day. In spite of this large tonnage, developments in the automatic control of coal flotation circuits have lagged significantly behind those for mineral systems. One reason such developments have been limited is that instruments have not been available for the on-line measurement of carbon or ash and another critical variables in coal slurries. A second reason is that the influence of the operating variables on coal flotation has not been completely understood. During the last few years some of the required instrumentation has been developed and an improved knowledge of the flotation process itself has occurred through mathematical modeling; as a result certain control strategies for coal flotation are beginning to emerge. This paper attempts to evaluate several control strategies using a detailed flotation dynamic simulator, DYNAFLOAT. After constructing a process matrix for the system of interest, promising alternatives for linking manipulated and controlled variables have been analyzed. In order to develop combined grade and recovery control strategies, the authors found it necessary to construct a grade/recovery map with the aid of the simulator to drive the system to known final, feasible grade/recovery operating conditions. Finally, an advanced strategy which uses an on-line model to identify disturbances and take control actions is proposed.

Jan 1, 1983