Search Documents

By I. Matsunaga, K. Aoki, W. -j. Jung

Blasting is widely used in mining and basic construction because of its speed and economy to destroy the rocks. Blasting has the advantages of reduced excavation costs and shorted construction time when compared to the use of heavy machinery for excavation and cutting such as that with a tunnel boring machine. There are numerous problems with blasting, including the noise, vibration and fly rock. So it is necessary to accurately evaluate fracture mechanics of rocks on the dynamic loading condition to control the fracture process of the blasting. The tests using Hopkinson's effect for the dynamic condition using the precise detonators were performed for various strain rates on three different kinds of rocks. In the tests using Hopkinson's effect for the dynamic condition, the high-speed camera was used to observe the fracture process of the test sample rocks. As the results of experiments there was an increase in the tensile strength of rock with an increase in the strain rate for three kinds of rock on the dynamic loading. The tensile strength of rocks with high porosity on the water saturation condition was decreased on the both static and dynamic condition. It is clear that the strain rate and water saturation were influenced to the tensile strength of the rocks.

Jan 1, 2003

By K. Schwerdtfeger

Data are presented on the effect of iron oxide on the electrical conductivity of CaO-SiO2-FeO-Fe2O3melts, and on limiting current and impedance in direct current or alternating current charge transfer at iron electrodes. The strong influence of iron oxide content can be utilized for in situ determination of total iron oxide content and Fe3+/Fe2+ratio. The possible probe designs are presented and the principles and procedures of the measurements are explained. Keywords: in situ probe for iron oxide determination in steelmaking slags, electrical conductivity of CaO-SiO2-FeO-Fe2O3slags, direct current over voltage and alternating current impedance at iron/slag electrodes.

Jan 1, 2004

By Y. M. Chen, H. L. Zhang, W. U. Bing, C. Q. Zhou

Multiphase flow in the widely used Vanyukov furnace was numerically studied. An unsteady three-dimensional and three-phase flow model was firstly built using the computational fluid dynamics (CFD) software ANSYS FLUENT®, and then solved with the volume of fluid (VOF) and k - ??model. The results showed that the proposed model could be used to predict the multiphase movement, the slag/air fluctuation, the vortex formation, and effects of structural and operational parameters. By fast Fourier transform (FFT), the dominant frequency of density with time signal was calculated as 0.29 Hz. The analysis of different injection flow rates of enriched air indicated that this variable has a major effect on the mean slag velocity. The peak mean velocity increased from 2.17 to 4.99 m/s while the flow rate of enriched air varied from 70 to 160 m/s. The proposed model provides a method to optimize the furnace structure and operating conditions for the best furnace performance and lowest energy consumption.

Jan 1, 2015

By K. Yathavan

Fracturing of rock at low stress levels can be a source of unexpected problems in rock engineering: • the resulting instability can be a safety hazard; • in very brittle rocks it may be associated with violent failure of the rock and strainbursting (rockbursting); • it usually leads to an unexpected requirement for rock support, with time and cost implications; • in rock boring projects, it may result in fracture of the rock ahead of the bored face and in the walls of the bore behind the face. This may lead to cutter head vibration, increased cutter wear and consequently decreased performance and increased costs. Examples of situations in which fracturing of rock at very low stress levels has been observed will be described. This will include details or estimates of the in situ stress magnitudes and the rock strengths involved. La brisure de roche sous faibles contraintes peut être l’origine de problèmes inattendus en génie minier : • L’instabilité résultante peut devenir un danger • Elle peut provoquer des éclatements violents des roches fragiles • Elle nécessite souvent une infrastructure de soutien de la roche, ayant des implications sur les coûts et les délais • Les forages de la roche peuvent provoquer une brisure de celle-ci au niveau de la surface forée mais ainsi à l’intérieur de la roche, causant parfois des vibrations et une fatigue de la tête de forage, induisant une baisse de performance et un accroissement des coûts. Nous avons décrit ci-après des exemples de situations de brisure de roche sous faibles contraintes. Cette description comprend des détails ou des estimations des forces et des contraintes impliquées. Cette étude représente la base du travail de recherche effectué sur le phénomène. ißbildung im Gestein unter niedrigen Stressbedingung kann eine mögliche Ursache sein für unerwartet auftretende Probleme in der Felsmechaniklehre: • Die resultierende Instabilität stellt ein mögliches Sicherheitsrisiko dar; • In sehr sprödem Gestein kann es verbunden sein mit einem plötzlichen und gewaltsamen Zerfall des Gesteins; • In den meisten Fällen ist eine nicht eingeplante Gesteinsabstützung erforderlich, und damit ein Zeit- und Kostenaufwand verbunden; • Bei Bohrungsprojekten kann es dazu führen, daß es während des Bohrvorganges zu einer Rißbildung im Gestein hinter und vor der gebohrten Felswand kommt. Dies kann Bohrkopfvibrationen, eine erhöhte Bohrkopfabnutzung und folglich eine Bohrleistungssenkung, sowie Kostenerhöhung zur Folge haben. Das Phenomen von Gesteinsrißbildung unter niedrigen Stressbedingung wird anhand von einigen dokumentierten Beispielen erörtert. Diese beinhalten zudem Details oder Schätzungen bezüglich der Stärke des in situ Stressfeldes, sowie der gegebenen Gesteinsstärken. Die mit diesem Beitrag dokumentierten Ergebnisse formen eine Grundlage zur weiteren Forschung dieses Phenomens.

Jan 1, 2003

By G. L. Smith

The fundamental challenge facing mineral and metal companies is how to create sustainable value while operating within mandated strategic bounds, identified constraints, and variable market and economic conditions. This can be achieved by allowing the fixed physical nature of the mineral asset to drive definition of the optimal technical solution to mining and processing activities, and developing and resourcing a strategically aligned portfolio of production entities that creates flexibility to near- and longer-term business environment shifts, i.e. a production mix that allows variation of output to respond to short term market variation, within a long term context. The practical achievement of this outcome is enabled by the concept of strategic long term planning. The core elements of strategic long term planning in the metals and minerals industry, and the relationship between them, are expanded. The strategic long term planning framework is a logic construct that enables delivery of an optimized, strategically-aligned business plan from the mineral asset portfolio using a set of tools and techniques with a common language, standards, systems and processes to align decisions and actions on a cyclical basis.

Jan 1, 2012

By J. M. Cardoso, E. F. Quadros, A. Chiarini, F. Fernandes, G. Vilela, J. Ireno, L. C. Agostini

Based on the geological-geometric characterization of the basaltic rock at the site of a factory for chemical products situated in the Southern region of Brasil, and on results of a significant number of packer tests, the principal directions of flow were estimated, taking into consideration the intersection and the orientation of the joints and the amount of contaminant flow measured in each interval. The tests were performed using the multi-packer hydraulic multitest probe of IPT (HMTP) instrumented with an electric conductivity meter. A method of analysis for three-dimensional evaluation of the amount of contaminant flow in the area was proposed for future mitigation of the problem. Basé sur une caractérization géologique-géotechnique de la roche basaltique existant sur un site dune fabrique de produits chimiques située au sud du Brésil et sur les resultants dún nombre significantif déssais du type packer, les directions principales d´écoulement ont été estimées en considerant l´intersection et orientation des joints et la quantité de contaminant mesurée sur chaque intervale d´essais. Ceux-ci ont été realizes en utilisant une sonde multipacker developée au IPT – São Paulo (HMTP) instrumentée avec un mesureur de condictivité électrique. Une méthode d´analyse 3-D pour l´évaluation du transport du contaminant sur ce site a été proposée pour une future mitigation du problème. Auf Grund der geologischen Struktur des Basalts auf dem Gelände einer chemischen Fabrik in Südbrasilien und der Ergebnisse einer ansehnlichen Zahl von Pumpversuchen wurden die Hauptfließrichtungen bestimmt unter Berücksichtigung des Kluftgefüges und der in jedem Intervall gemessenen Menge kontaminierten Wassers. Die Versuche erfolgten mit dem im IPT entwickelten Verfahren (HMTP) mit Mehrfachpackern und elektrischen Leitfähigkeitsgebern. Ein analytisches Verfahren zur dreidimensionalen Ermittlung der Mengen kontaminierten Wassers wurde für die künftige Befassung mit dem Problem entwickelt.

Jan 1, 2003

By A. H. Mokken

Failed attempts at amalgamation of a gold/osmiridium concentrate, recovered behind pebble mill liners during re-lining, led to the discovery that the gold particles were coated and that nitric acid only could remove the coatings. Following this treatment amalgamation was rapid and resulted in a complete recovery of the gold that otherwise would have been lost in plant residues. Investigations into the nature and formation of the coatings led to the realization that the coatings were impregnations of harder elements, associated with the gold during grinding and driven into the softer gold surface by high pressure, impact and attrition. It was further realized that this phenomenon could be part of gold ore milling, world-wide. With these thoughts in mind the question is asked whether concentration down to micron sizes prior to cyanidation, should not play a greater role in gold recovery.

Jan 1, 1999

By P. Rice, A. Photolo, A. C. Barnard

Introduction -Sampling Tool Project (STP) -History -Results to date -Costs -Questions

Jan 1, 2005

By N. J. Castilla, R. Giglio

"Circulating fluidized-bed (CFB) combustion technology has been around for over 40 years, but over the last 6 years it has been commercially demonstrated at the 500 MWe scale at the Lagisza plant located in Bedzin, Poland. The CFB at the Lagisza plant has unique first-of-a-kind design features, such as vertical-tube supercritical steam technology and a lowtemperature flue-gas heat extraction that allows the plant to achieve high plant efficiencies of over 43% (net lower heating value). Another unusual feature for a coal power plant is that this plant meets all its atmospheric emission permit levels without any post-combustion de-NOx or de-SOx equipment such as selective catalytic reduction (SCR) or flue-gas desulphurization (FGD).CFB clean coal power technology is entering the utility power sector just in time to help deal with declining quality in internationally traded coals and to promote the large-scale use of economic, low-quality domestic fuels. Owing to the very attractive price discounts, growing supplies of low-quality Indonesian coals are outpacing the supply of high-quality Australian, Russian, and US coals. In Germany and Turkey, the use of domestic lignites for power production provides a secure and economic energy solution while creating domestic jobs.Conventional pulverized coal (PC) boilers will have trouble accepting these off-specification coals because of their narrow fuel specifications; they typically call for heating values above 5500 kcal/kg. This limitation is not an issue for CFB technology because of its ability to burn the worst and best of coals with heating values ranging from 3900 to 8000 kcal/kg.This paper provides an outlook for future coal supply, quality, and price, as well as a review of the technical and economic benefits of CFB technology firing low-quality fuels for utility power generation."

Jan 1, 2015

By S. Read, G. Cook

The Hoek-Brown failure criterion is often applied to a wider range of rocks than the isotropic rock masses to which it is strictly applicable. This paper evaluates the patterns of defects in rock masses using spherical projection contour plots of samples of randomly-generated orientations and datasets from mapping of New Zealand closely-jointed greywacke rock masses. Two indices from the contour plots - the area within the 1% contour (A1%) and maximum concentration (Cmax) are introduced for distinguishing uniform (isotropic), random or regular defect patterns. The indices provide a potential extension to current guidelines on the use of the Hoek-Brown failure criterion. The paper also outlines kinematic checks to assess the influence of defect clusters on rock mass strength. Das Hoek-Brown Bruchkriterium, das strikte nur fuer isotrope Gefuege gilt, findet oft einen viel weiteren Anwendungsbereich. Diese Arbeit bewertet diverse Dispersionsmuster der Defekte einer Gesteinsmasse. Wir vergleichen in sphaerischer Projektion (1) Beispiele zufaelliger Orientierung von Defekten und (2) Felddaten ueber neuseelaendisache engstaendig geklueftete Grauwacken. Die Projektionen werden durch die Indices A1% (Flaechenanteil des 1%-Bereichs) and Cmax (Hoechstkonzentration) gekennzeichnet, welche isotrope, zufaellige und regulaere Muster unterscheiden und die aktuellen Richtlinien zum Hoek-Brown Kriterium ergaenzen. Wir testen ferner Defektgruppen der Gesteine kinematisch auf ihren Einfluss auf Massenfestigkeit. Le critère de rupture de Hoek-Brown est souvent utilisé sur une variété de roches plus étendue que les masses rocheuses auxquelles il est strictement applicable. Ce travail évalue la distribution des défauts au sein d'une masse rocheuse en utilisant une projection sphérique des contours d'échantillons d'orientations générées aléatoirement et de données de cartographie provenant de greywackes à joints rapprochés de Nouvelle Zélande. Deux indices de cette projection - la zone des contours en dessous de 1 % (A1%) et celle de concentration maximum (Cmax) sont introduites pour distinguer les répartitions uniformes (isotropes), aléatoires ou régulières. Ces indices fournissent une extension potentielle aux règles d'utilisation du critère de rupture de Hoek-Brown. Ce travail utilisent également les contrôles cinématiques pour évaluer l'influence des groupes de défauts sur la résistance de la masse rocheuse.

Jan 1, 2003

This paper describes a simple finite element (FE) modelling approach which leads to the computation of seismic energy release rate (ERR) and strain energy storage rate (ESR) which result from mining. The concept of critical strain energy is introduced as a means to help evaluate the strainburst potential in mine structures. A new, energy-based, burst potential index (BPI) is proposed. The use of ERR, ESR and BPI is demonstrated by a cut-and-fill stope case study. The merits of using such energy parameters in the interpretation and analysis of strainburst phenomena are discussed. While the study gives promising results, site-specific back analyses would be required to first calibrate the model and fit it with the local mine conditions, before it can be adopted as a routine design tool.

Jan 1, 1999

By A. Fahimifar, H. Soroush

Abstract: Triaxial tests were conducted on the schist specimens with various anisotropic angles under confining pressures of 0, 7 and 15 MPa, and axial stress-axial strains, were measured and plotted for various conditions. The results obtained reveal the effects of schistose on the strength and deformability of the rock very clearly. Peak strength of the specimens for 00 and 900 schistose orientations are nearly the same. Modulus of elasticity of this rock varies with anisotropic angle. For 0 orientation modulus of elasticity increases to a maximum. Confining pressure increases the peak strength and improves the rock deformability. However, this effect is not the same for various orientations, and there are no similar trends for each anisotropy direction. Analysis of the results shows that consideration of a linear failure criterion such as Mohr-Coulomb is appropriate for the prediction of rock behaviour up to 10 MPa, rather than a non-linear one. The analysis also reveals that the friction angle and cohesion are affected by the anisotropy orientation, and this effect is more important for the cohesion than the friction angles. Resume: Les esseys triaxiales sur les echantillon d un roch schist avec les differents angles non-isotrop sous les tension lateral zero et sept et qoinze mega pascal (mpa) est fait et les covtraite et allongment unitaire sont mesure et leur curues est destine sous different condition les resultats obtenues montre les effets du schistosite sur le resistance et le ductilite vissiblement. Le resistance final sur les echantilions pour les angles o degre et 90 degree est equivalent. Le modoule d elasticite de ce roch sera difere par a port de l angle de stratification. Pour l angle o degree le valeur de modoule est le maximum. le pousse lateral augmenterai le resitance final, et sera amilterai le toleran le de ductilite. Mais cette effet bn est pas unigue pour les different stratification, et pour les diferents directions no– isotrop it n y a pas le meme solution. L analyse des resulitats montre que le criterre de ruin comme mohr–colomb est moderate pour le pousse lateral jusq av lo mega pascal , et ce n est pas neccesaire d utiliser de criterre no–linear . Cette analyse aussi montre que l angle de frottement et cohsion est en relation de la direction no–isotrop, et cette effet est olus important pour le cohsion par a port de l angle de frottement . Abriß : Dreiachsige Prüfung wurde auf den schist Exemplaren mit verschiedenen anisotropic Winkeln unter Bestätigen von Drücken von 0.7 und 15 MPa geleitet, und axiale Spannung axiale Spannungen, wurden gemessen und für verschiedene Bedingungen wurde geplant. Die Ergebnisse haben die Wirkungen von schisocity auf der Kraft und dem deformability des Felsen sehr deutlich erhalten offenbart. Maximale Kraft der Exemplare für 0° und 90 sind° schistos Orientierungen beinahe das gleiche. Modulus der Elastizität von diesem Felsen ändert sich mit anisotropic Winkel. Für 0° vermehrt Orientierung modulus der Elastizität zu einem Maximum. Einschränkender Druck vermehrt die maximale Kraft und verbessert den Felsen deformability. Aber ist diese Wirkung nicht das gleiche für verschiedene Orientierungen, und es gibt keine ähnlichen Tendenzen für jede anisotropic Richtung. Analyse der Ergebnisse zeigt jener Überlegung Kriterium eines linearen Ausfalls wie zum Beispiel Mohr Coulomb passend für die Voraussage von Felsen Verhalten bis zu 10 MPa, anstatt eines nicht linear ist. Die Analyse offenbart auch, daß der Reibung Winkel und Bindekraft werden beeinflußt von der anisotropic Orientierung, und diese Wirkung wichtiger für die Bindekraft ist, als der Reibung Winkel

Jan 1, 2003

By D van der Merwe

Tracers of known densities are used world wide in coal processing plants to evaluate plant performance. Tracers are added to the feed stream and are counted after being recovered from the product and discard streams to determine partition curves. The need to recover the tracers can be eliminated by adding radio frequency identification tags to the tracers. Readers mounted on the product and discard streams record the passing RF tracers and produce the partition curve instantly. Tests were performed with three different shaped tracers at different collieries on cyclones ranging from 510mm to 800mm in diameter. Sink and float analyses of coal samples were used to compare conventional partition curves to partition curves obtained by using RF tracers. The average amount of tracers recorded was 78% of tracers in the feed. The results indicate that the stone shaped tracers represent the results from the sink-float analyses the best. The results suggest that RF tracers can be used to evaluate cyclone circuits in the coal industry and will make it possible to evaluate a coal circuit?s efficiency without stopping a plant and waiting for laboratory analyses. Keywords Coal tracers, partition curve, radio frequency tracer, RFID

Jan 1, 2006

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By A. E. Lewis

The emphasis of this paper is on the characterization and testing of the slag produced by a secondary lead refinery. This work forms part of a broader investigation aimed at reducing loss of valuable product from the process as well as minimizing the environmental impact of the process wastes. It was this work that led to a critical examination of the standard waste classification tests. Characterization of the slag was carried out using a number of complementary techniques. In the broader context, the slag characterization aided in identifying process deficiencies and thus was a critical tool in suggesting potential for process optimization. For this study, the slag characterization provided a relatively comprehensive picture of the composition and properties of the slag, which facilitated understanding the behaviour of the slag under batch test conditions. On the basis of quantity of hazardous components alone, the slag is hazardous according to South African Acceptable Risk Limits (ARL). However, when both the quantity and the leach potential of the hazardous components is taken into account, standard waste tests carried out by three independent agencies indicate that the slag should not be classified as hazardous according to local regulations. Also, according to United States Environmental Protection Agency (US EPA) limits, which are independent of the quantity of the waste, the slag would not be classified as hazardous. The standard waste tests used by the independent agencies was the Toxicity Characteristic Leach Procedure (TCLP), a test which was developed by the US EPA to classify hazardous wastes. One of the requirements of this batch test is that it should be quick, simple to carry out and that the results should be reproducible. Previously, the applicability of the TCLP test to mineral processing and metallurgical wastes has been challenged on a number of points. Additional testing of the slag was carried out using both the TCLP and the Synthetic Precipitation Leach Procedure (SPLP) recommended by the American National Mining Association as being more appropriate for mineral processing wastes. The particular physical and chemical characteristics of the secondary lead slag highlighted additional limitations of both the TCLP and SPLP tests as standard laboratory batch procedures. Keywords: environmental protection, secondary lead processing, slag, leach testing, TCLP, SPLP, ARL, hazardous waste, batch tests

Jan 1, 2000

By Huang Zhiwei, Paul Skayman, Kevin Holley

In 1989 The First Brigade for Geology and Mineral Exploration of Qinghai Province discovered gold at Jinlonggou and Qinlongtan, Tanjianshan. Between 1992 and 2002 small scale mining was carried out at these sites using underground mining methods at Jinlonggou and an open pit at Qinlongtan. During 2003 and 2004 geotechnical investigations were carried out in support of a bankable feasibility study. An important objective of this investigation was to meet both internationally accepted standards and codes of practice, and also to satisfy the Chinese requirements. Extensive use of local experience was utilised. Where possible geological drilling information was incorporated into the assessment. Extensive geotechnical mapping of surface and underground exposures, and index testing to gain an appreciation of rock intact strength were used to characterise the sites. Rock mass classification (MRMR) was used to assess indicative overall slope angles and appropriate bench stack heights for the proposed pits at Jinlonggou and Qinlongtan. Measured discontinuity orientations were used in kinematic analysis to assess stability of possible pit slope geometry at a batter and overall scale to provide preliminary recommendations for the pit slope configuration. Numerical modelling was also carried out to improve the understanding of anticipated pit behaviour. Site investigation and preliminary geotechnical design details, that incorporate site specific conditions for the formation of open pits at Tanjianshan, are discussed in this paper.

Jan 1, 2006

By E. V. Lilford

A number of countries have introduced codes governing the valuation of mineral assets and securities. The African continent will follow suit in due course considering the importance of the global minerals industry as it relates to the attraction of foreign investment. South Africa is to introduce the Petroleum and Minerals Development Bill legislating the involvement of previously disadvantaged individuals and communities in the country?s minerals industry. One of the challenges facing the successful implementation of such codes and bills lies with the abilities of independent valuators to value mineral properties and projects on a consistent basis. Certain valuation principles and methodologies are applicable in all jurisdictions in the minerals industry. These valuation tools and principles are considered and developed in this report. They have been discussed and developed to encourage minerals valuators to consider and consistently apply the most applicable valuation methodologies.

Jan 1, 2002

By G. G. le Roux

The purpose of the investigation was to assess various options for increasing the efficiency of the conveyor belt transporting system used at 4 Belt Shaft at Lonmin?s Marikana operations. The reason for the investigation was to prevent the occurrence of a ?bottleneck? at the main ore passes delivering ore to the conveyor belt system, thus creating more fluent operational conditions. The options assessed for increasing the efficiency of the conveyor belt transporting system were: ?Variation of the conveyor speed ?Concurrent tipping from two ore passes on the belt ?Increase the available drive unit power ?Increasing the feed rate from vibratory feeders ?Change in belt width/belt specifications The report shows that the most preferable option to the current situation at 4 Belt, Lonmin, would be the option of concurrent tipping from two ore passes to the belt.

Jan 1, 2008

By Li. S., C. Sili

Abstract. Study on nonlinear damage localization process of rocks under water chemical corrosion is a more interesting topic in rock mechanics research world widely. It is very important in estimating long term stability of rock engineering, design of nuclear waste repository and its performance estimation, geothermal and petroleum development. This paper reports that new development of study on the topic, including methodology, results of meso-mechanical test, real-time CT scan test and acoustic emission test, temporal fractal behaviors, neural dynamic modeling and chemical-induced damage law, etc. This paper also discusses the research directions of the topic in the near future. Zusammenfassung. Untersuchung zum durch die chemische Corrosion induzierten Schaedigungsprozess ist einer der Trends im Gebiet der Felsmechanik. Sie ist zugleich ein sehr wichtiges Forschungsprojekt u.a. fuer geotechnische Langzeitstabilitaetsanalyse, Langzeitsicherheit eines Endlagers, Erdwaerme- und Erdoelfoerderung. Dieser Aufsatz stellt die neusten Entwicklungen in den folgenden Teilgebieten zusammen: Untersuchungsmethoden, Laborversuchsergebnisse der Mikromechanik, der Computer-Tomographie und der akustischen Emission, zeitabhaengige Fraktaleigenschaften, Modelle fuer die Nervendynamik sowie Modelle fuer chemie-induzierte Schaedigungen. Zum Schluss werden kuenftige Forschungsschwerpunkte bzw. –richtungen diskutiert. Résumé L’étude du processus de la localisation de l’endommagement du à l’érosion chimique est un thème d’actualité pour la mécanique des roches. Elle est également un sujet de recherche d’importance dans l’évaluation de la stabilité à long terme des ouvrages rocheux, l’analyse du system de stockage des déchets nucléaires et l’évaluation de son comportement, l’exploitation de l’énergie thermique et pétrolifère, etc. Cet article présente le développement actuel dans ce domaine, incluant la méthodologie d’étude sur le processus de la localisation de l’endommagement dû à l’érosion chimique, l’analyse des essais mécaniques avec l’observation microscopique, du balayage en temps réel (CT), et de l’émission acoustique. On aborde ainsi modèle des caractéristiques fractural du temps, le modèle de la mécanique dynamique neural, ainsi que la loi de comportement d’endommagement dû à l’effet chimique. Enfin, les perspectives relatives à ces études sont présentées et discutées.

Jan 1, 2003