Search Documents

By C. Kwong, L. H. Rorden, T. C. Moore

This report describes the feasibility test of an electromagnetic method for locating, boreholes, with or without casing, that have been drilled in conjunction with mining operations but whose location with respect to the tunnel is not precisely known. The first tests were conducted with the cooperation of the Kerr-McGee Corporation, Church Rock Mining Operations, New Mexico, in September 1977. These tests demonstrated that accuracies of better than ±15% of range and ±1° of bearing can be achieved with a simple system and setups. Subsequent tests, in January 1978, on a horizontally drilled pipe line river crossing application, by Ti tan Contractors of Sacramento, California, demonstrated that accuracies of better than one-half percent of range and a few tenths of one degree of bearing can be achieved by using refined techniques. The demonstration tests were done at ranges on the order of 100 to 200 feet but the method is capable of working at much greater distances.

Jan 5, 1978

By R. F. Tenney

No detailed information has been published heretofore on the performance of small industrial-type anthracite stokers in building-heating service, apparently because of the difficulty of comparing the performance of one unit with that of another over an entire season's operation. Studies of competitive heating fuels have been similarly handicapped, and attempts to compare fuels are seldom technically sound in this investigation, the performance of a 60-in. Losch4 stoker burning rice-size anthracite in a standard commercial boiler was observed during a 4-month winter-spring season. It was used to heat two buildings at the Bureau of Mines' Anthracite Research Center at Schuylkill Haven, Pa., with the customary type of automatic pressure-range control. Attendance was limited to inspecting, fuel weighing, data recording, and ash removal. Results were computed daily and grouped by weekly periods to minimize daily irregularities. The same stoker-boiler unit had already been tested in a series of American Society of Mechanical Engineers (ASME) test code runs, with the stoker running continuously and with other conditions well stabilized A comparison of results from the code test and the building-heating tests provided information not available in the past for a single stoker unit, assisted in analyzing heat losses not computable in a cyclic operation, and established a basis for evaluating stoker performance in heating service.

Jan 1, 1963

By A. C. Fieldner

The Bureau of Mines has recently conducted a study of results obtained in analyzing similar samples of coal and coke by 25 laboratories throughout then country, in comparison with results obtained in the Bureau's coal laboratory at Pittsburgh. The purpose of this work was primarily to obtain a comparison of the methods of coal analysis used by the laboratories of the American Gas Association. Therefore, four standard samples of coal end one of coke ware prepared in the Bureau of Mines coal laboratory at Pittsburgh, and portions sent to each laboratory. At the same time, a like number of standard samples were submitted to 12 commercial laboratories rot affiliated with the Association, for the purpose of comparing their analyses with the results is obtained by the U. S. Bureau of Mines and the American Gas Association. Tire comparison is based on the average of 24 analyses by the Bureau of Mines on each kind of coal, and the accompanying curves show the deviation from this average analysis, together with deviations from the check limits of the American Society for Testing Materials.

Jan 1, 1923

By John J. Sammarco

This report (Safety File Guidance 6.0) is the eighth in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [5.1System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 4, 2006

By John J. Sammarco

This report (System Safety Guidance 5.1) is the sixth in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various lifecycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 8, 2005

By Andrew B. Cecala

The Bureau of Mines conducted laboratory and in-mine tests on the Racal airstream helmet (Model #AR21) to evaluate its protection efficiency. Laboratory tests indicated that as ambient air velocity increased, the protection offered by the helmet decreased. In tests conducted at several coal mine long-wall sections with face velocities under 400 fpm, the helmet was 84 pct effective at reducing respirable dust in the miner&apos;s breathing zone. However, at a high-velocity section, 1,200 fpm, the efficiency of the helmet was significantly reduced, confirming our laboratory results.

Jan 1, 1981

By Robert M. Becker

A multistage probability model for assessing the reliability of mineral samples following any number of stages of sample reduction is presented. Sample reduction is the process of alternately crushing or grinding and sampling mineral particles prior to assaying. The final multistage model developed accurately describes the ideal sample reduction practice. This model is based on previously developed and experimentally tested models for a single stage of sampling. The problem is approached through the probability distributions for the various stages of sampling. The probability distribution, moments, and moment relationships for a single stage of sampling are first reviewed, and the useful concept of unit moments is defined. In presenting the models for two stages of sampling, emphasis is placed on the physical description of the sample reduction process which leads quite naturally to its mathematical representation. In this representation, crushing or particle-size reduction between the stages of sampling is viewed as a random process with respect to the number and proportion of particles of the various kinds produced. The physical and mathematical description is extended to more than two stages of sample reduction, and the first three moments for any number of stages are developed. In common sample reduction practice the effects of a finite population (finite amount of material) at each stage of sampling appear to be important in describing the variance contribution of each stage. This is also true for the third moment about the mean. An example is cited in which the skewness increases by more than an order of magnitude when several stages of sampling are considered. This is largely due to the dependence of the multistage third moment about the mean on the variance. In general the model and results should be useful in helping to understand, control, and reduce the random errors that arise in the sample reduction process.

Jan 1, 1968

By Walter E. Pittman

This Bureau of Mines study surveys the current state of technology and the various research efforts that have been undertaken to dewater the dilute phosphatic clays generated in the production of phosphate rock. The research described includes early dewatering experiments, fundamental studies of clays and of flocculation, and minor dewatering techniques such as freeze-thaw methods, the ANDCO process, moving screens, sand wick, crust development, and overburden pumping. Some methods that are currently being evaluated are described. They include the Estech sand-clay mix process using the Enviro-Clear thickener, sand-clay sandwiching, dredge mix, dredge process, and the sand-spray process. Developing technology for dewatering phosphatic clays also is described, including the Bureau of Mines rotary trommel method and the Gardinier process.

Jan 1, 1984

By E. D. Calvert

As part of its goal to minimize the requirements for critical and strategic minerals, the Bureau of Mines is conducting research to foster the use of domestically abundant materials such as molybdenum. This report describes the development of an investment shell molding technique that can be used to make castings of molybdenum and its alloys. The mold material is cubic Zr02 with a monoclinic Zr02 binder. The shell, formed by standard investment molding techniques described in the text, is prepared for molybdenum casting by firing for 6 hours at 1,550° C (2,822° F) or for 4 hours at 1,650° C (3,002° F). The resulting castings have predictable and reproducible dimensions with good detail. As-cast strength is poorer than the strength of wrought materials below 1,600° F. At and above this temperature, tensile strengths of cast and wrought materials are nearly equal. Aqueous corrosion of the castings in most media is insignificant.

Jan 1, 1982

By J. N. Tomlinson

Trailing-cable splices are evaluated for moisture exclusion abilities after repeated travel over shuttle-car sheave wheels. Tests are conducted on cables with jackets made of neoprene, cholrosulphonated polyethylene (CSPE), and nitrile butadiene-polyvinyl chloride (NBR-PVC) to 50° C. The results show that some splice kits are effective as received, others are improved with minor but significant changes, and still others must be redesigned to be effective in underground applications. Laboratory results are compared with actual underground splice results. Recommendations for cable preparation prior to splicing are presented.

Jan 1, 1979

By R. H. Storch

This report describes work done as part of a Bureau of Mines program to appraise the titanium-mineral resources of Idaho. The work included both field reconnaissance and a spot churn-drilling program. Much general information was available, as a result of earlier work done under the Western Radioactive Minerals Exploration Program conducted between 1950 and 1954 by the Bureau of Mines for the United States Atomic Energy Commission. This particular exploration provided data as to the quantity of ilmenite (TiFe03) and accessory black-sand mineral concentrates in a number of placer deposits; however, at that time no tests were made to ascertain if the ilmenite was of marketable grade. The spot churn drilling was begun in the Gold Fork area of Long Valley, Valley County, Idaho (fig. 1), in August 1956 and was completed during October of the same year. Eleven holes (designated as the GF series on fig. 2) 35 to 45 feet in depth, aggregating 425 feet, were completed during this period. Data from other exploration drilling in 1951 was used in this report. The 13 holes in the G series shown in figure 2 were drilled by the Bureau of Mines for the United States Atomic Energy Commission; the 7 holes of the DH series were drilled by the Bureau of Reclamation. The 20 holes, ranging from 16 to 140 feet in depth, totaled 1,625 feet. The combined number of all samples recovered was 422. Those taken in 1956 were composited for each drill hole and sent to the Bureau of Mines laboratory in Albany, Oreg., for analyses.

Jan 1, 1958

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

6. Development of Mine Sealant Material Systems 6. 1 Introduction The preliminary evaluation of material systems described in Section 3 led to the selection of the following four promising systems for further development: System A: Aggregate, Fly Ash System System B: Aggregate, Fly Ash, Urethane Foam System System C: Aggregate, Bulkhead, Light Expansive Concrete System D: Aggregate, Self-Supporting Thick Slurry Preliminary laboratory tests indicated that the building of effective bulkheads from one borehole would be extremely difficult. Two extra boreholes would be required adding to the overall cost of the system and making the system less attractive. Tests with light expansive concrete showed that bulkheads would be required, the material would not support itself. As a result, further development of this system was terminated. Foam concrete was selected as the most suitable material to be developed into a self-supporting, rapid-setting slurry. A laboratory investigation of its use for mine sealing was conducted during this program; the results are summarized in Section 6. 5 and details of the laboratory program are presented in Appendix B.

Jan 1, 1973

The Bureau of Mines has conducted considerable research to improve life support technology for underground mining applications. This proceedings volume presents several new developments that may help increase the chances of mine workers in surviving underground disasters. Several papers address the performance of present self-contained self-rescuers (SCSR&apos;s) and provide proposed guidelines for the design and testing of a second-generation SCSR. Improvements In the safety and effectiveness of mine rescue and recovery operations are described, including the design of a low-profile rescue breathing apparatus and a rescue team helmet.

Jan 1, 1987

By Benjamin Petkof

Production quarry blasts in three rock types were photographed with a high-speed camera. Analysis of the films showed that step increases sometimes occur in the horizontal velocity of the broken rock. These step velocity increases were observed only in the first foot or so of rock movement. This observation indicates that the gaseous products of the explosion do additional work on the rock after it is crushed and cracked by the initial compressive-stress pulse and the reflected tensile-stress pulse. The observed initial fly-rock velocity is compared with the calculated fly-rock velocity for reflection spalling. A mechanism possibly causing the velocity increases is discussed. INTRODUCTION When a small concentrated charge of explosive is detonated at the bottom of a drill hole near a free surface, two modes of rock failure have been observed; both are associated with the stress pulse generated in the rock by the detonating explosive. The first mode of failure is the crushing and radial tensile cracking associated with the initial passage of the compressive-stress pulse as it propagates outward from the explosion. This type of rock failure is usually confined to the immediate vicinity of the charge hole. The second mode of failure is the tangential and radial tensile cracking associated with the tensile-stress pulse that is reflected from the free surface. This mode of failure is commonly called scabbing or spalling and has been shown to be a primary cause of rock failure in crater formation at one free surface. (3).4

Jan 1, 1961

By K. C. Strebig

The effect of some organic additives in diamond drilling of quartzite was investigated in the laboratory with a drill instrumented to measure the rate of penetration, the thrust, and the torque and to record each as a function of the distance drilled. A statistical plan was followed throughout the investigation, and an equation representing the bit performance was derived from the mathematical theory of reliability. The coefficient of friction in drilling increased with the use of additives, although the wear coefficient decreased. The decrease in wear associated with an increase in energy per unit volume consumed and the increase in penetration rate resulted in a net decrease in the cost per foot of drilling. A hypothesis explaining the effects achieved with the additives is given.

Jan 1, 1971

Provide mine safety personnel, MSHA inspectors, and original-equipment manufacturers with guidelines and a check list for inspecting rollover protection structures (ROPS) being used in mining operations. The Problem ROPS are provided on mobile surface mining equipment to protect operators from such safety hazards as machine rollovers, falling objects, and collisions. However, the protective capability of a ROPS can be greatly reduced if it is damaged. Certain kinds of damage, such as hair- line cracks, corrosion, and loosened bolts, may occur as a result of normal machine use but may not be recognized as unsafe by untrained personnel. Therefore, the Bureau of Mmes designed a manual which can be used by mine personnel when inspecting ROPS equipment. The Manual The manual was prepared to help acquaint mine safety personnel and MSHA inspectors with typical ROPS deficiencies and their causes. It provides a systematic means for inspecting ROPS so that the identified deficiencies and their causes can be corrected. It is suggested that an inspection of the ROPS be conducted after every 1,000 h of equipment operation, or sooner if the structure has been subjected to any unusual loads which could cause damage, such as a rollover, highwall caving, or collision. The manual also details common deficiencies in the structure and attachment hardware which may affect the service life. The checklist, when used as instructed in the manual, provides a means for systematically inspecting the structure to ensure maximum protective capability and conformance with applicable Federal regulations.

Jan 1, 1986

Improve the safety, reliability and overall effectiveness of mine stench warning systems and to provide a means of remote control stench injector operation. Approach Industrial gas odorants were analyzed for their suitability for use in mine stench warning systems. A prototype stench injector capable of precise flowrate control was designed, fabricated, and tested using the odorant chosen as having the most favorable properties. Based on the results of the field tests, a second generation injector was developed. The second generation unit features optional remote control operation, and in addition, is simpler to refill and is less expensive than the original injector. A complete second generation system, consisting of two manually operated injectors and one remote controlled injector was in-mine tested through actual mine fire drills. How It Works Ethyl mercaptan mixed with Freon is the predominant stench agent used in the U.S. underground metal and nonmetal mines. However ethyl mercaptan&apos;s toxicity,

Jan 1, 1982

By J. Burlin Johnson

In small-scale blasting experiments conducted in the Bureau of Mines laboratory, small charges were used to produce craters in blocks of concrete mortar. The results are compared with larger scale experiments of other research workers, and the comparison demonstrates the similarity of the results obtained and indicates that small-scale blasting should be a useful tool for predicting large-scale blasting effects. INTRODUCTION The purpose at this investigation was to conduct blasting experiments in mortar in the laboratory and then, by comparing the results with those from larger scale field blasts in rock to determine to what extent, if any, the laboratory results resemble those in the field. The work described herein was the initial phase of a project aimed at evaluating small-scale blasting as a tool for use in improving blasting techniques. It is evident from the stand-point of control and cost that small-scale blasting would be valuable in the study of rock fragmentation by blasting in mines and quarries, if the extrapolation is valid.

Jan 1, 1962

By Donald S. Colby

CARBON-BLACK shipments, which had declined in the latter art of 1953, remained low in 1954 until after settlement of the labor strike that occurred in the rubber industry in July and August. The production of new model automobiles in the last quarter of the year spurred the demand for rubber tires and consequently the demand for carbon black. Total shipments of 1,498 million pounds for the year were 4 percent below 1953.

Jan 1, 1958

By A. J. Farstad, R. F. Kehrman

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped driers in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light- weight and inexpensive.

Jan 1, 1979