Search Documents

By John J. Gordon, Neil K. Cooperrider

The International Organization for Standardization (ISO) standard ISO 2631 [1,2] provides three methods for evaluation of human exposure to vibrations that contain occasional shocks or impacts. Part 1 of the standard specifies the running r.m.s. or maximum transient vibration method (MTVV) and the fourth power vibration dose value (VDV). Part 5 of the standard provides a method of computing the stress in the lumbar spine for humans exposed to multiple shocks. Alem et al [3] have reported application of these methods to data for tactical ground vehicles. This paper reports and compares VDV and spinal stress evaluations of more than 90 hours of vibration and shock measurements on North American locomotives engaged in through freight operations. The measurements evaluated in this paper were obtained for full crew shifts on 19 freight locomotive runs on mainline track in locations from New York to California. The shifts ranged in duration from 187 minutes to 497 minutes. The average speeds for the shifts were from 21.0 mph to 54.6 mph. All measurements were made on locomotives hauling freight trains in regular revenue service. Data Acquisition and Processing The results reported here were computed using test data acquired from a tri-axial seat pad, accelerometer at a sample rate of 400Hz with an anti-aliasing filter corner frequency of 100Hz. The VDVs and the lateral and longitudinal spinal stress values were computed directly from the acquired test data according to the procedures specified and described in [1] and [2]. The vertical spinal stress values were computed by converting the as-acquired test data to a sample rate of 160Hz for input to the vertical spine model, as required in [2]. The conversion of the test data from the as-acquired sample rate of 400Hz to the required sample rate of 160Hz involved up sampling or interpolating the test data to an equivalent sample rate of 800Hz, band limiting the resultant data with a low-pass filter corner frequency of 60Hz and finally down sampling or decimating the 800Hz data to a sample frequency of 160Hz. Discussion The vertical VDVs computed according to [2] for the 19 shifts ranged from 2.68 to 9.33 m/s1.75. In all but one case, the vertical values were greater than the values for the lateral or longitudinal directions. Note that the health guidance in [1] puts the lower boundary of the health guidance caution zone at a VDV value of 8.5 and the upper boundary at 17 m/s1.75. The daily equivalent static compression dose computed following [2] ranged from 0.123 to 0.434 MPa. Health guidance provided in [2] states that there is a low probability of an adverse health effect if the daily dose is less than 0.5 MPa.

Jan 6, 2006

By John Nagy, Austin R. Cooper

Information is presented on the pressure and rate of pressure development during a dust explosion . The data were obtained in laboratory studies in a 75- cubic inch vessel with mineral , agricultural and chemical dusts . The factors investigated include dust concentration , oxygen concentration of the atmosphere , admixed inert powder , and admixed moisture . Information is given also on the effects of these factors on the composition of the atmosphere after the explosion .

Jan 1, 1964

By W. W. Culter

"This paper is the outcome of thorough investigation into the value of the previous methods used for deriving production decline curves. It is highly important that methods be employed that are fundamentally sound and also practicably applicable. Six methods commonly used were studied. Some of these were found to be fundamentally in error; some save reliable curves but involved much work and time in the preparation; others gave reliable curves with less time and effort.It was found that of the methods previously employed the ""family curve"" method described in Bull. 134 Amer. Inst. Feb. 1918, pp. 499-500 by Lewis and Beal, was probably the most satisfactory. The now method given in this paper ploys the same principles as the ""family curve"" method, but is mathematical instead of graphical,The engineer and the oil man should carefully boar in mind both the use and the limitations of the average production curve such as is derived by the ""family curve"" method or other methods mentioned. Estimations of future productions or of underground oil reserves of a particular tract or well should be made from the production records of the tract or the well itself wherever such records are satisfactory. The use of the average curve of a district or field should be applied only to those properties or wells where there are not sufficient data to construct individual or tract production records, or where the productive life so short that a satisfactory individual record can not be obtained."

Jul 1, 1920

By Bruce D. Sartwell

A program was written which utilizes a remote teletype input to a time- sharing computer to plot charged particle or X-ray energy spectra which are stored in the memory of multichannel analyzers. The program, written in FORTRAN V, accepts the data printed out by the pulse height analyzer on paper tape and then, after reading these data tapes into the computer, plots on the teletype the desired energy spectra on a scale automatically adjusted for the maximum number occurring in the data. The program is flexible enough so that the researcher can subsequently expand or contract the vertical (intensity) or horizontal (energy) scales. With a slight modification, the program will accept data printouts from scalers or analog to digital converters. The program also includes a feature for integrating the energy peaks obtained by pulse height analysis.

Jan 1, 1970

By W. H. Pailes, V. Castranova, D. Lewis, G. Goodman

We performed bronchoscopy with bronchoalveolar lavage (BAL) in 8 control subjects with no exposure to occupational dusts, 8 healthy power plant workers exposed to mixed dusts (primarily fly ash), 1 healthy coal miner and 1 rock driller with acute silicosis. All subjects were non-smoking males. We analyzed lavage effluents for total numbers of alveolar macrophages, lymphocytes and neutrophils and monitored chemiluminescence at rest (REST CL) and after stimulation with 3x10- M phorbol-12-myristate-13-acetate (PMA CL) or 2 mg/ml zymosan (ZYM CL). The data are as follows:

Jan 1, 1988

By Byron M. Bird

"The prevailing practice of washing unsized coal, 1/2-inch and finer, to 1/8-inch and finer, on a table is subject to certain limitations which are commonly overlooked. In some instances good results are obtained by this method, but often the opposite is true and the efficiency of the washing operation is low. Although the separation taking place on a concentrating table is not fully understood, the actual distribution of particles of various sizes and specific gravities was determined a number of years ago by ore-dressing investigators. Hence this paper consists of an analysis of an old problem by new methods. The experimental data on which the discussion is based were obtained in the course of coal-washing investigations conducted by the U. S. Bureau of Mines at the Northwest Experiment Station in cooperation with the University of Washington and with certain coal operator: of that State.Experimental WorkThe general method of study has been to take a large number of zonal products from the table, and separate them according to specific gravity and size into their component parts. The table used is one of the standard commercial sizes with a diagonal deck. The coal to be washed is split into representative portions, which are stored in separate bins. One portion is used for ""timing as"" the table; the products are collected continuously in the same turned to the feed bin, and thus a closed circuit is completed. When the despite conditions on the table are obtained, coal is fed from one of the re. After the table is operating smoothly the entire product is minute; such a sample is sufficiently large to represent accurately the work of the table and at the same time to minimize the effect of beginning at the end next to the head motion, separate samples are made for each foot along the edge of the deck."

Jun 1, 1926

By Edward F. Divers

This Bureau of Mines report describes the results of a laboratory evaluation of a mechanical dust collector (scrubber) suitable for underground coal mine applications. The scrubber was developed by the Mining Research and Development Establishment (MRDE), Burton-On-Trent, England, and tested at the Federal Bureau of Mines Pittsburgh Mining and Safety Research Center (PMSRC) as part of a technical exchange program. The 2,000-to 8,000-cfm scrubber consists of an electrically driven vane-axial fan, water sprays, a 2-inch-thick, loosely knit stainless steel wire filter panel, and a water droplet eliminator. The dust-laden airstream travels axially through the water sprays, filter panel, fan, and eliminator. Slurry water drains into a sump where a belt-driven pump recycles it back to the sprays. Fractional breakdown tests showed a maximum dust collection efficiency of 96 pct of respirable-size (less than 7 µm) coal dust at 2,000 cfm. Efficiency decreased with increasing airflow; for example, to 91 pct at 6,000 cfm. Following these tests the original wire panel was replaced with a similar but smaller panel developed at PMSRC; a marked improvement in dust collection occurred at all flow rates tested.

Jan 1, 1979

By R. C. Ellman

Significant effects of in-the-mill drying on the pulverization of lignite have been demonstrated in an experimental impact-type pulverizer by tests in which the primary variable was temperature of the sweeping gas. Reduced power requirements and increased product fineness were observed as the extent of drying was increased. Pulverization with in-the-mill drying was studied in comparative tests made on lignites from five mine sources. All of the lignites responded in a similar manner; however, differences in the pulverizing characteristics of the individual lignites were significant. For one lignite, the electrical input to the pulverizer driving motor with minimum sweeping-gas temperature was 33.9 kw.-hr. per ton, decreasing to 14.0 kw.-hr. per ton with a sweeping-gas temperature of 658° F.; for another lignite, at comparable operating conditions, the electrical input decreased from 59.1 to 19.0 kw.-hr. per ton. In the first case, the product fineness increased with increasing temperature of sweeping gas from 65.2 to 79.2 percent through a 200-mesh sieve, and in the second case, from b2.7 to 86.9 percent through a 200-mesh sieve.

Jan 1, 1962

By L. B. Berger

"INTRODUCTION Accurate determination of carbon monoxide in concentrations ranging from 0.2 to about 0.5 percent by volume is troublesome, because such concentrations are too high for some analytical methods and too low for others. Methods that are sensitive to concentrations of carbon monoxide considerably less than 0.2 percent are approaching their upper limit of usefulness when applied to the analysis of samples containing 0.2 percent or more of carbon monoxide, and it may be necessary to resort to dilution of the sample with a known proportion of air, or otherwise modifying the analytical technique, to obtain satisfactory results. Such methods include the determination of carbon monoxide by reduction of heated iodine pentoxide 3/4/5/ by the ""Pyrotannic acid"" method 6/ and by the so-called ""phosphomolybdic acid"" method. 7/ The use of conventional gas-analysis equipment, such as the Orsat type, in the determination of carbon monoxide in concentrations ranging from 0.2 to 0.5 percent is not desirable, as possible analytical errors may be of about the same magnitude, thus producing results of little quantitative value.For several years prior to this publication, the Gas Analysis Laboratory of the Health Division of the Bureau of Mines has used a modification of the Haldane type 8/9/10/ gas-analysis apparatus for the determination, by absorption in a chemical reagent, of carbon monoxide in low concentrations that are not readily determined by other methods. The method is applicable also to the determination of higher concentrations. As the procedure has proved successful and has been adopted by others, this report was prepared to describe the method and to present results of analyses obtained with it."

Nov 1, 1947

By E. J. Gleim

A study of the records on file in the Bureau of Mines reveals that moray fire in coal mines have been started by electrical equipment or circuits. There the fires were of undetermined origin, electricity often was Strongly suspected as the probable cause. While it is unfortunate that positive evidence as to the cause is so often lost in the general destruction resulting from fires, there are many lessons to be learned from fire s in which the origin was definitely established as electrical. For modern high-speed methods of producing coal, electrically operated machinery has become virtually indispensable underground. With increases in the amount of equipment it has not always been necessary to increase the number of circuits in the mine where direct current is mainly used, but it has been necessary to increase the carrying capacity of these circuits. For example, lends such as heavy-haulage units drawing 1,000 amperes or more have brought boat the introduction of 6/0 and "No. 9 section" trolley wires. This has not made the task of fire prevention any easier, for it has meant that circuit breakers s must be set so high that partial short circuits fail to open them, therefore an arc of considerable proportions can be maintained without causing the, beaker to open. Thus, if as fall of roof brought a trolley wire down against a loaded car of coal, an arc might be struck that would ignite they cowl without opening the circuit breaker.

Jan 1, 1937

By L. C. IlsLey

The last previous Bureau of Mines publication relative to details of permissible methane detectors (Bulletin 331, published in 1930) describes detectors of four different types, namely flame, combustion, catalytic, and a combination Weatstone-bridge and catalytic type in which catalytic action at the surface of a platinum filament when in methane causes a change in the temperature and resistance of the filament, thus unbalancing the bridge circuit and giving a reading proportional to the methane concentration. Three detractors of the latter type have been approved since 1930. A brief description of each follows: U. C. C. Detector Approval No. 902, covering the U. C. C. indicating detector, as described in Bulletin 331, was extended. January 27, 1930, to cover important changes in design that permit checking the calibration of the detector at any time whether in gas or fresh air. Essential features of the detector are shown in figure 1.

Jan 1, 1937

By R. Carson Dalzell

The use of nuclear fission for chemical process heat offers the special advantage of high temperature, limited only by materials of construction. The process heat may be supplied economically at elevated pressures, since no compression of combustion air is required. For the initial effort in developing a high-temperature reactor, the indirect cycle, using helium as the heat-transfer medium, was chosen. The major problems are the design of high-temperature fuel elements, construction of an exchanger to transfer heat to process streams in the range of 2,500° F., and development of compressors capable of recycling helium at 1,000° F. and above. A conceptual design of a nuclear reactor to furnish process heat for coal gasification has been made. Spherical fuel elements utilizing a graphite structure, impregnated with uranium carbide fuel, were chosen, as spheres offer the possibility of easier loading and unloading of the reactor. Calculations of pressure drop and gas-pumping power for the system are included.

Jan 1, 1959

By Elizabeth G. Baglin

Research was conducted by the Bureau of Mines to determine the feasibility of using electrokinetic densification to dewater Bayer process red mud, magnetic black mud prepared by pressure digestion of red mud in the presence of ferrous sulfate, and magnetic black mud formed by simu-lated Bayer digestion of Jamaican bauxite with added ferrous sulfate. Tests showed that the solids content of presettled muds could be increased from 25 pct to approximately 40 to 48 pct by gravity draining followed by electrodewatering for approximately 48 h. Electrodewatering may not be practical because of increased reagent and processing costs and because the muds must be thoroughly washed prior to electrodewatering to remove dissolved ions and decrease mud conductivities.

Jan 1, 1988

By R. F. Abernethy

A chemical method of determining microgram quantities of arsenic in coal was investigated by the Bureau of Mines to supplement a semiquantitative spectrographic method of determining arsenic in coal ash. In accordance with a method recommended by the International Organization for Standardization, 1-gram samples of coal are decomposed by wet oxidation with boiling sulfuric acid (H2S04) and nitric acid (HN03) to remove the organic matter. After heating to fumes of SO3 to remove HN03, the arsenic is separated as arsine by the action of zinc in H2S04 solution. The arsine is absorbed in dilute iodine solution in which the arsenic is determined colorimetrically by the molybdenum-blue reaction. Two modifications of the method for obtaining the arsenic in solution, in addition to the wet oxidation method, give satisfactory results. The modifications are (1) furnace ashing with MgO added to the coal, followed by treatment with H2S04, and (2) extraction of arsenic from the coal by dilute HNO3 without ashing. Float-and sink-tests show that arsenic is associated mainly with mineral matter in the three coals examined. High-temperature ashing tests show that very little arsenic is volatilized from coal ash below 1,000° C, but it is virtually all removed from the ash at 1,300° C.

Jan 1, 1968

By F. N. Kissell, C. H. Elder, C. M. McCulloch

The applicability of the "direct method" for determining the methane content of virgin coalbeds was tested. Preliminary results indicate that the direct method, when applied to exploration cores, can be successfully used to estimate coalbed gas content and also approximately predict the total gas emission from a prospective mine located in the coalbed at the exploration site.

Jan 1, 1973

By A. T. Iannacchione, D. G. Puglio

The Bureau of Mines established geologic factors affecting the mining of the Lower Kittanning coalbed to aid in coalbed minability studies and examined the occurrence of "wants" (places where coal is missing) and types of unstable roof rock strata. Trends established from mapping, including prediction of areas of high methane emissions, were extrapolated to unmined areas. "Wants" in the coalbed are of two types: Erosional and depositional. Erosional features occur where north-south-trending sand-filled channels cut into the coalbed. Variations in depositional environments have caused the coalbed to "split" into several thinner units. Slickensides, commonly indicative of unstable roof, are adjacent to and on the underside of sandstone channels; they were caused by differential compaction and by soft sediment sliding along the contact between the sandstone and adjacent shale. The frequency of unstable roof also increases where the interval between the Middle and Lower Kittanning coalbed is less than 30 feet. The zones of weakness at the contacts above and below the Middle Kittanning coalbed are the controlling factors for unstable roof in these strata. Methane emissions from the coalbed are controlled primarily by depth, fracture permeability, and rank of coal. Local geologic factors are coalbed thickness, associated rock strata, structure, and proximity to outcrop.

Jan 1, 1979

By A. B. Hooker

[Permissible electric cap lamps represent a workable balance between the amount of light needed and the various limiting conditions, such as the weight the miner can carry conveniently, cost of the lamp, including upkeep, and adequacy or practicability of the lamp as regards safety, mechanical strength, and general performance. Other things being equal, the coot desirable lamp is one that gives the greatest amount of useful light. Conversely, with a given amount of light the most desirable lamp is one that its the most efficient respecting weight, cost, and performance.]

Jan 1, 1935

By A. B. Hooker

[Permissible electric cap lamps represent a workable balance between the amount of light needed and the various limiting conditions, such as the weight the miner can carry conveniently, cost of the lamp, including upkeep, and adequacy or practicability of the lamp as regards safety, mechanical strength, and general performance. Other things being equal, the coot desirable lamp is one that gives the greatest amount of useful light. Conversely, with a given amount of light the most desirable lamp is one that its the most efficient respecting weight, cost, and performance.]

Jan 1, 1935

By Allan F. Smith

The Bureau of Mines studied toxic products produced by burning eight fire-resistant mines conveyor belts, a brattice cloth, and an electrical cable insulation obtained from laboratory-scale burning experiments under various air-flow conditions. Generally, CO product concentrations for most materials were noticeably higher then the NO2 and HC1 levels that were measured; also, no phosgene was detected. However, several of the fire-resistant belt samples yielded HC1 concentrations that were above the reported lethal level for 1/2 to 1-hour exposures, although these data were limited to flow conditions where air dilution effects were small; the belt materials that showed this behavior included samples of polyvinyl chloride, styrene butadiene, styrene butadiene blends, and a British neoprene which yielded the greatest amount of toxic vapor. In addition, some results are presented on the phosphoric acid concentrations that may be produced from the decomposition of ammonium dihydrogen phosphate when dispersed on a burning coalbed.

Jan 1, 1973

By J. E. Gebhardt

External control of the electrochemical potential of a bed of mineral particles has been investigated by the Bureau of Mines as a method for controlling particle inter-action with organic collectors and thus, flotation response. A cylindrically shaped, 200-to 300-g bed of sulfide mineral particles was used as the working electrode to examine the potential distribution in the bed. The dissolved oxygen concentration of the electrolyte had a significant effect on the potential profile across the mineral bed. Low oxygen levels were necessary to achieve uniform electrochemical potential distributions. Flotation separation of a chalcocite-pyrite mineral mixture by controlled potential was achieved using ethylxanthate, but the flotation behavior of chalcocite and pyrite from the mixture does not follow the flotation behavior of the individual minerals. That is, the presence of another sulfide mineral alters the flotation behavior with ethylxan-thate. Galvanic interaction due to mineral-to-mineral contact between chalcocite and pyrite contributes to differences in the recovery. Chalcocite dissolution products had a deleterious effect on pyrite flotation by activating flotation below -0.1 V (saturated calomel electrode) and depressing flotation above -0.1 V. Pyrite dissolution products had no effect on chalcocite flotation.

Jan 1, 1985