Search Documents

By W. A. Stickney

As part of a Bureau of Mines program to investigate recovery of manganese (Mn) from low-grade materials, laboratory studies were made of four samples of mill rejects: Three from Montana and one from Peru. These studies demonstrated that certain mill-waste products can be a potential source of manganese. Both manganese oxide and carbonate minerals were recovered by flotation in an acid circuit with a fuel oil-tall oil emulsion as collector. Sintering) required to prepare a physically acceptable product, also was used as a method of beneficiation. In addition to being low-grade, some of the samples presented problems of intimate mineral association and complex textures.

Jan 1, 1960

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial scale mill. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough so that realistic rate determinations could be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1988

By S. J. Broderick

[The term "nonmetallic minerals,? as commonly used in the mining industry, refers to those minerals of industrial importance that are mined essentially for uses other than for the metals contained. The field comprises several hundred minerals of industrial importance, of which 70 have been adequately described in the textbook Industrial Minerals and Rocks.3/ A few of the more important nonmetallic products are sand and gravel, salt, phosphates, clays, refractories, linestone, and cement materials. Some of tic minerals, such as bauxite and pyrolusite, have both metallic and nonmetal is applications, but in this report only the nonmetallic mineral phases are considered. In the organic field of nonraetallics only coal is considered, as, the, others - petroleum, natural gas, natural bitumens, and hydrocarbons - are of no importance in water softening.]

Jan 1, 1941

By J. M. Stuve

Low-temperature adiabatic heat-capacity determinations were made by the Bureau of Mines in the temperature range from 5 to 300 K for the two crystalline modifications of zinc sulfide, sphalerite (ß) and wurtzite (a). The entropy at 298.15 K of sphalerite was evaluated as l4.02±0.04 cal/deg mole and wurtzite, l4.06±0.04 cal/deg mole.

Jan 1, 1974

By Lowell B. Moon

Regardless of how a mineral deposit in first discovered or by whom, any mining enterprise based upon it must pass through a preliminary stage of exploration. The common understanding of ?exploration? among mining engineers is well-expressed by Jackson and Knaebel:3/ Exploration work ranges from that performed by the individual prospector employing only the simplest tool, and equipment to elaborate campaigns involving the expenditure of largo stuns of money end the use of churn- car diamond-drilling equipment, large test-pitting crews, or sometimes a regular mining organization. In any event, the object is to determine as accurately as possible, with the funds available, the size, shape, and other characteristics of the ore bodies and their average value or grade.

Jan 1, 1945

By August J. Kwitowski

The U.S. Bureau of Mines developed and tested a teleoperating system to control a new highwall mining system. A remote operator was provided out-of-sight sensory information and control of coal extraction and haulage equipment. Surface and production testing proved that the teleoperating system supplied the operator with sufficient sensory information to operate the mining system. Details on the teleoperating system provided in this report include (1) sensor selection, (2) a description of the electronic control system, (3) equipment selection and modifications, (4) the positive test results, and (5) recommendations for system improvements.

Jan 1, 2010

By H. E. Sanford

"INTRODUCTION Of the occupations in and about coal mines, those of the haulage crews are among the most hazardous. Statistics indicate that the second largest number of fatalities about coal mines occurs during haulage operations and through the use or misuse of haulage equipment. Despite the fact that relatively few coal-mine employees are engaged continuously at haulage operations, approximately 20 percent of all coal-mine fatalities are attributable to haulage.Most of the hazards in haulage operations could be very greatly reduced if more serious consideration were given to the problems of the haulage crews and if sincere efforts were made to reduce the hazards. Underground haulage is similar in many respects to railroading; yet, railroading is now considered one of the safest of occupations a distinction that has been attained only by honest effort and whole-hearted cooperation on the part of all concerned. Underground haulage is also similar to street and highway operation and has in it some of the difficulties encountered in the reduction of traffic accidents the seriousness of which has not by any means been con¬trolled as yet, notwithstanding the fact that much effort has been expended through a multiplicity of laws, ordinance regulation, etc., as well as by thousands of enforcement agencies and officers.The men working on the locomotives are among the most important members of a coal-mine organization; without skilled haulage employees, the production of coal would be greatly retarded. Their jobs, particularly the job as brakeman, require physical endurance, agility, and mental and physical alertness; in thin coal beds, especially where the roof is not brushed and the coal is loaded into mine cars by hand, the need for these qualifications is greatly increased."

May 1, 1948

By Gwendolyn D. Hood

The Bureau of Mines investigated techniques for dewatering slurries from talc-processing operations to improve water reclamation and pro-duce dewatered solids suitable for disposal. Various flocculating reagents were evaluated, and a nonionic polyacrylamide was found to be most effective in a specialized flocculation dewatering technique. The flocculation dewatering method was applied in laboratory batch tests and in continuous tests using a static screen, a belt-roller device, and a clarifier-thickener laboratory unit. In continuous tests using the unit, wastes of 3.5 pct solids were dewatered to 56.9 pct solids using 0.03 Ib of flocculant per ton of dry solids treated.

Jan 1, 1983

By Robert P. Vinson

This report describes three coal mine ventilation studies by the Bureau of Mines in which sulfur hexafluoride (SF6) was used as a tracer gas. One of these studies was conducted to determine air movement and leakage in a sealed area. Another was run to determine the ventilation efficiency of a bleeder system. Finally, a study was made of air leakage across permanent stoppings of parallel intake airways. These studies proved sulfur hexafluoride to be a useful addition to the equipment commonly used in coal mine ventilation analysis.

Jan 1, 1976

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United States and publishes economic data on the industry, based upon reports from producers. This publication lists all producers that reported commercial production to the Bureau for 1959. The companies named herein represent virtually all commercial producers of peat. A few companies, however, may not have been canvassed or failed to respond, as tine survey is voluntary For producers, arid the industry has many small operations that operate intermittently. No consideration was given to the quantities of peat produced and output of the various companies listed ranged from less than 100 tons to more than 50,000 tons, Peat is included in the Bureau's annual surveys of the mineral industries because, technically, peat is a fuel. Although none is used for fuel in the United States, peat is a potential source of energy and one of our large mineral resources. The domestic peat industry produces peat chiefly for use as a soil amendment. The industry has expanded rapidly during the past decade with active operations increasing from 45 in 1947-49 4/ to 105 in 1959. Output during this period has increased 218 percent, rising from 131,782 net tons to 419,460 net tons.

Jan 1, 1960

The National Institute for Occupational Safety and Health (NIOSH) National Personal Protec-tive Technology Laboratory (NPPTL) and the Mine Safety and Health Administration (MSHA) conduct a Long Term Field Evaluation (LTFE) program to evaluate deployed self-contained self-rescuers (SCSRs). The objective of the program is to evaluate how well SCSRs endure the under-ground coal mining environment with regard to both physical damage and aging when they are deployed in accordance with Federal regulations (30 CFR 75.1714). This report presents ?ndings of the combined eighth and ninth phases of the LTFE. For these phases, over four hundred SCSRs were evaluated. The units tested include the CSE SR-100, Draeger Oxy K-Plus, MSA Life-saver 60, and the OCENCO EBA 6.5. The OCENCO M-20 was evaluated only in Phase 9. Testing was per-formed between December 2000 and April 2004. Results of the evaluation indicate that all SCSRs experience some performance degradation due to the mining environment. Observed degrada-tion varies from elevated levels of carbon dioxide, high breathing resistance, and reduced capacity. Mechanical degradation to the SCSR components included breathing hoses, chemical beds, outer cases and seals. The LTFE tests discussed in this report are different from tests performed for SCSR certi?cation to the requirements of 42 Code of Federal Regulations, Part 84 (42 CFR, Part 84). LTFE tests reported here are conducted to an end point, oxygen depletion, to enable comparison of the duration of new and deployed SCSRs. The method for obtaining deployed SCSRs for this evalua-tion was not a random selection from the deployed population of SCSRs. Although the results of these tests are useful for observing performance of the tested SCSRs, they are not representative of all deployed SCSRs. A new evaluation protocol, with revised sampling strategies, test methods, and reporting procedures, is currently being designed to enhance the generalizability of the results. This program will be implemented following completion of Phase 10 of the current LTFE protocol.

Jan 10, 2006

By Philip W. Holland

This U.S. Bureau of Mines (USBM) report describes a chromatographic method that is used for rapid field determinations of carbon dioxide in natural gas streams at a USBM helium production facility. The method employs a commercially available portable gas chromatograph that is equipped with a 10-m fused-silica capillary column coated with a porous polymer. The instrument operating parameters permit determinations to be performed over a concentration range of 10 ppm to 10 pct with a frequency of 20 samples/h. The speed at which determinations can be performed is an important factor when evaluating efficiency or troubleshooting processes at the helium facility.

Jan 1, 1994

By James W. Townsend, William H. King

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Alisman, chief, Salt Lake City Division, Mining Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon ore such technique.The Wright borehole-surveying instrument developed at the Homestake mine, Lead, S. Dak., has been described in several publications. 3/ For the benefit of those to whom the publications are not available, the instrument is described here. However, this article will be concerned mainly with the technique developed by the Federal Bureau of Mines for using the instrument.In the use of the Wright borehole-surveying instrument, it was found advantageous to develop a standard practice of operation covering type of film, preparation and care of film, loading film in instrument, placing instrument in container, exposure time, unloading film from instrument, development of film, and determination of dip and strike from film impressions."

May 1, 1947

By R. E. Morgan, J. F. Barkley

"INTRODUCTION In city smoke-abatement work it is customary to require approval of the sizing of fuel-burning equipment. This is to insure that, with reasonable attention, the equipment can be operated essentially smokelessly, having such features as ample furnace volume and air supply. To answer the many inquiries that come to the Bureau of Mines as to what dimensions are acceptable and standard, the requirements of a number of smoke-abatement ordinances have been tabulated.CONCLUSIONSStudy of these tabulations shows that even after many years of fuel-burning practice and experience there is no common standard. Variations in the requirements for the same type of equipment under the same conditions of operation are great. This causes considerable difference in installation costs. Over-all costs being affected, the competitive positions of different types of fuel-burning equipment are also affected. It is apparent that there is a lack of information as to proper dimensions that is commonly accepted as authoritative.DISCUSSIONTable 1 gives the minimum furnace-setting heights required by various cities for mechanical underfeed stokers installed under H.R.T. boilers. Figure 1 shows a typical installation. The dimension given for each case is the distance from the dead plate of the stoker to bottom of boiler shell, unless otherwise noted. As shown in the table, different cities use different size-classification systems; it is not possible to make complete, exact, direct comparisons. Table la gives a comparison for various cities, showing the approximate percentage difference in H.R.T. furnace-setting heights required from those recommended by the Stoker Manufacturers' Association arbitrarily chosen to serve as a basis of comparison. The percentages are approxi¬mate because they were calculated as if all heights as given were measured from the dead plate of the stoker. In two cases a lower height is permitted, in a number of cases the height may be the same, and in a number of cases the height must be greater. The percentage increase goes to 100 in one case. Lack of uniformity is quite evident."

Mar 1, 1950

By Kenneth B. Higbie

Expenditures to advance scientific technology in general reached an all time high in 1965 with some $22.2 billion estimated to have been allocated by government and industry. Federal Government expenditures were estimated at $15.4 billion, with almost 90 percent of the funds devoted to programs involving defense, atomic energy, and outer space efforts. With this massive effort in the United States and a very impressive effort elsewhere in the world, there is little wonder that many new metallurgical developments were announced in the technical press during the year. No effort has been made to cover all aspects of the industry, but a few of the developments are described in this chapter.

Jan 1, 1966

To address the safety of programmable electronics-based mining systems before this technology proliferates in the mining industry.

Jan 1, 1999

By A. Wahab Khair, N. P. Reddy

"Abstract. This paper attempts to characterize coal breakage due to the action of a continuous miner. Coal blocks with an approximate dimension of 45.7 cm x 38.1 cm x 15.2 cm (18 in. x 15 in. x 6 in.) were first subjected to confining pressures equivalent to in-situ conditions. Then the blocks were cut along the face/butt cleat direction by the cutting head of a specially designed unique automated rotary coal cutting simulator (ARCCS), simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-sit and operating parameters a number of other para¬meters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis.INTRODUCTIONThe Federal Coal Mine Health and Safety Act of 1969 was enacted to emphasize to coal operators that the airborne respirable dust should not exceed 2 mg/m3, thus reducing the incidence of coal workers pneumoconiosis.Dust control techniques such as conventional water sprays and dust collectors are only partially effective and require additional equipment expenditures. A more authentic approach would be to reduce respirable dust at the source the continuous mining machine cutting head, where the fragmentation process occurs. Improving the fragmentation process by characterizing the coal breakage will not only reduce respirable dust at the face, but it will also decrease the amount of respirable dust that is liberated during the secondary handling.Fragmentation of coal can be expressed as a function of three major groups of parameters; namely, 1) coal properties, 2) in-situ conditions and 3) operating parameters. This paper deals with the characterization of coal breakage along both face/butt cleat direction as a function of machine operating parameters such as rate of advance, angle of attack, bit configuration, bit lacing (spacing and pattern) and bit speed at various equivalent in-situ pressures."

Mar 1, 1989

By D. S. Burgess

The characteristics of gas-phase detonations were observed in 20 instrumented firings within earthen tunnels, in 100 such detonations in a 24-in-diam by l63-ft-long steel pipe, and in about 200 smaller scale firings. Most of the fuels studied were representative hydrocarbons--acetylene, propane, gasoline, and a roughly equimolar mixture of methylacetylene, propadiene, and propane. In a pipe with two closed ends, the detonable limits were demonstrated to be very nearly the same as reported limits of flammability. The side-on impulses (pressures integrated over 200-msec intervals) were shown to be the same function of concentration regardless of whether deflagration or detonation had occurred. In a pipe with only the initiation end closed, the impulses of all fuel-air systems tended toward the same level when averaged over comparable ranges of fuel concentration; the lower pressures with saturated hydrocarbons were nearly compensated by longer durations of pressure transient. In all fuel-air systems, unexpectedly high impulses were obtained with slightly lean mixtures. In earthen confining structures, the impulse, of the explosion was efficiently converted into momentum of the failing wall. In the configurations studied, an earth velocity of about 20 fps was critical to overcome the soil's resistance to shear. The destructive effect was determined by gas pressure rather than by total energy release. The assignment of a "TNT equivalent" to an explosive gas mixture is discussed in terms of the confinement of the mixture.

Jan 1, 1968

By A. B. Hooker, L. C. IlsLey

"Field inspections and data relative to the use of rubber—sheathed trailing cables in mines show that much cable is ruined or its probable life shortened by being overheated in service.The length of cable required to make connection from a source of supply to a machine at the face workings may be 100 to 500 feet. As a rule, the cable is carried on a reel and unreeled as required; and thus in most cases some of the cable is not removed from the reel. The overheating generally occurs in that part of the cable which is left on the reel.Factors that determine the heating of trailing cables are:1. The size of the conductors in the cable.2. The maximum energy to be supplied through the cable, based upon the horsepower of the motor and the degree to which the motor is loaded.3. The voltage of the supply and the variation of the voltage at the receiving4. The time length of current flow and whether continuous or intermittent.5. The kind of current (direct or alternating).6. The amount of cable left on the reel.7. The type of cable used.8. The kind of reel used.In connection with an investigation of the general performance of rubber—sheathed trailing cables, the Bureau of Mines has made a limited study of some of these factors, including the following points:"

Jul 1, 1931

By A. V. Hooker, E. J. Coggeshall

"The Bureau of Mines for some time advocated the firing of all blasts in coal mines as single shots, and this method of firing is the general practice in American bituminous-coal mines. All single shots can be fired with permissible single-shot units so designed that they will not ignite mixtures of methane and air.If several shots in a face are fired singly it is necessary to return the face after each shot. In some mines having steeply pitching coal seams, this may be dangerous or even impossible, under these conditions shots are usually fired simultaneously.Several shots cannot be fixed simultaneously with permissible single-shot blasting units, and safe types of multiple shots blasters are not readily available. This means that the firing of multiple shots in gassy mines is usually accompanied by the possibility of gas ignition as the blast occurs.Tests have been made at the Pittsburgh Experiment Station to determine the possibility of developing safe types of multiple-shot units suitable for such use, or of applying other type safely in gassy sections of mines where firing shots singly is impracticable.The tests may be divided into the following four groups:1. Tests to demonstrate hazard in the use of existing types of multiple-shot units of the portable generator type.2. Tests to show the electrical characteristics of multiple-shot generator units relative to the possibility of preventing igniting sparks and of modifying the design and application of such units in furthering safety."

Mar 1, 1935