Search Documents

By K. C. Dean

Time and motion studies were made by the Federal Bureau of Mines on the hand and machine dismantling of scrapped auto starter motors, generators, and alternators for recovery of copper, aluminum, and iron. The studies showed that an individual with power handtools and convenient access to a hydraulic press, power bandsaw, acetylene torch, and power lathe could, in an 8-hour day, disassemble about 100 starters, or 150 generators, or 30 alternators. The scrap copper yield would be 280, 390, and 45 pounds, respectively, and the iron yield would be about seven times the copper weight. About 100 pounds of aluminum would be obtained from the alternators.

Jan 1, 1976

By Bernard Porter

The solubility of UO2 was determined at 1,250° C. in ternary melts of UF4 and BaF2 with CaF2, LiF, and SrF2. The solubility of Ce02 was measured at 800° and 850° C. in a solution of CeF3, BaF2, and LiF. The amount of La203 which dissolves at 950° C. in a binary mixture of LiF and LaF3 and a ternary of LiF, LaF3, and BaF2 was also measured. In each case, the amount of soluble oxide was mound to be less than 5 weight-percent. A procedure was developed for filtering fused, oxide-saturated fluoride melts in order to obtain a representative sample for chemical analysis. The oxide content of the samples was determined by an inert-gas fusion procedure.

Jan 1, 1961

By Foster Fraas

A separator for minerals of low magnetic susceptibility and fine particle size in a water suspension is described. A ring-shaped matrix of ferromagnetic fragments rotating so as to pass successively through magnetic-field and field-free regions provides for the separation. Application is illustrated in the separation of hematite and ilmenite from quartz.

Jan 1, 1966

By Vernon F. Swanson

Several laboratory flotation tests were conducted by the Bureau of Mines on a sample of unweathered diorite from the B. F. Camden property, Amherst County, Va. Results showed that an ilmenite concentrate analyzing 45.5 percent Ti02 (titania), 0.07 percent P205 (phosphorus pentoxide), and 2.21 percent Si02 (silicon dioxide) could be produced from a feed containing 7.72 percent Ti02 and 3.94 percent P205. Ti02 recovery in the concentrate was 47.6 percent in a batch test. The weathered saprolite material overlying the diorite required scrubbing and desliming to remove argillaceous material and preliminary flotation of apatite followed by flotation of ilmenite. The resulting concentrate analyzed 47.3 percent Ti02, 0.19 percent P205, and 0.99 percent Si02 from a starting feed of 8.99 percent Ti02 and 3.37 percent P205; TiO2 recovery was 54.5 percent.

Jan 1, 1963

By Hewitt Wilson

[ ]

Jan 1, 1927

By S. P. Kinney

During 1925, at Holt, Ala., the United States Bureau of Mines made a study of the composition of the gases at four elevations in the shaft of a furnace producing foundry iron. A report3 of the work was published in 1927. Some of the results of this investigation are shown in Figure 1. As indicated, the gas at the center of the shaft is low in CO2 content, while the gas in the vicinity of the wall is higher in CO2. The composition of the gases at the top and at the center of the stock column was not far different from the composition of the gas at the top of the bosh. The investigation indicated clearly that lean gas was channeling through the center of the column. More recently the study was enlarged in scope to include investigation of a furnace operating on Lake Superior ores in the Chicago district. A series of planes between the stock line and tuyères was surveyed. Means and apparatus were developed for obtaining, between the inwall and the center of the furnace, the gas composition, gas velocity, and temperature on each plane. A complete report4 of the investigation has recently been published.

Jan 1, 1929

By A. R. Taylor Jr.

The heat capacities of a-quartz form beryllium fluoride were measured at approximately 3° intervals from 8° to 300° K., using an adiabatic calorimeter. At 298.15° K the heat capacity and entropy were 12.39 cal/deg mole and 12.75 ±0.04 eu respectively. Enthalpy measurements were made with an ice calorimeter at approximately 30° intervals on the quartz and glassy forms of beryllium fluoride between 300° and 1,200° K. A melting point of 825° K and an 0,-8 type transition at 500° K with a heat effect of 75 ca1/mole were deter-mined from the enthalpy data for the quartz-type sample. Beryllium fluoride glass crystallized spontaneously into the quartz modification at 500° K. The heat of the reaction BeF2 (a-quartz) .... BeF2 (glass) was found to be 1,125 ±16 cal/mole at 298° K by solution calorimetry. This value, when corrected to 273° K, was used to correct for the heat absorbed by the formation of glassy BeF2 when the sample was dropped into the ice calorimeter from temperatures above the melting point. Using corrected enthalpy measurements, the heat of fusion was determined to be 1.13 kcal/mole at 825° K.

Jan 1, 1965

By W. W. Simpson

The Bureau of Mines conducted research to determine the effects of potassium trithiocarbonate (KTTC), a degradation product of potassium ethylxanthate (KEX), on flotation of chalcopyrite and molybdenite. Small amounts of KTTC were identified in fresh and aged solutions of KEX using thin-layer chromotography. Hallimond tube flotation tests on pure minerals showed that KTTC acts as a weak collector for chalcopyrite. Both KEX and KTTC tend to depress molybdenite, but the depression effect is easily overcome by addition of a small quantity of fuel oil. The results of the Hallimond tube tests were confirmed in batch flotation tests using a porphyry copper ore.

Jan 1, 1983

By Thomas L. McVay

Laboratory batch and pilot plant flotation tests were made to determine the feasibility of recovering commercial grade kyanite from a quartzite- kyanite rock from the Graves Mountain, Ga., deposit. Best results in laboratory and continuous tests were obtained using sodium carbonate for pH control, citric acid for quartz depression, and oleic acid as the kyanite collector. Over 80 percent of the kyanite was recovered in a concentrate analyzing 56.8 percent Al203 and 3.8 percent hydrochloric acid soluble Fe203. Subsequent treatment of the flotation concentrate by magnetic separation reduced the acid soluble Fe2O3 to 0.6 percent and increased the alumina content to 59.2 percent. Acid leaching of the concentrate gave a product analyzing 59.7 percent Al203 and about 0.1 percent Fe203. As a result of the beneficiation research, a commercial kyanite flotation plant was completed in September 1962 by private industry.

Jan 1, 1963

By Michael P. Moore, Christopher J. Rise

"Over the past twenty years, there have been numerous studies which have attempted to correlate the prevalence of Coal Workers' Pneumoconiosis (CWP) with different characteristics of the coal seam. Some investigators have tried to find a relationship, or the lack of a relationship, between the rank of coal seams and the incidence of CWP. Others have attempted to show that there is a positive correlation between the mean mass of respirable dust in the mine atmosphere and the prevalence of CWP. Still others have tried to determine the influence of the quartz content of respirable dust on the incidence of CWP. Unfortunately, many of these different investigations have conflicting conclusions.One area of research with conflicting conclusions deals with the relationship between the rank of the coal and the incidence of CWP. For example, an inves¬tigation conducted in Pennsylvania and West Virginia coal mines concluded that the prevalence of CWP increases with an increase in coal rank (1). A study in Great Britain also observed a close relationship between the rank of coal and the prevalence of CWP (2). However, another study involving 312 Appalachian coal miners concluded that the association between coal rank and CWP might be fortuitous and that other factors may be more important (3). In addition, an investigation involving 2,600 miners during a period of twenty years in Great Britain established that there is only a weak correlation between the prevalence of CWP and the rank of the coal (4). Consequently, it appears that there is still uncertainty as to whether or not the rank of the coal seam has an influence on the development of CWP.Another area of investigation concerns the relationship between the mean mass of respirable dust present in the mine atmosphere and the prevalence of CWP. A study involving 4,122 miners over a period of ten years in Great Britain noted a high correlation between the mean mass of respirable dust and the incidence of CWP (5). Another investigation involving 3,154 British face workers con¬cluded that the overall mass of respirable dust is the factor most closely related to the ten-year attack rate of CWP (6). However, a study conducted in thirty-one mines in the United States concluded that it is doubtful that the quantity of respirable dust alone is responsible for the difference in the prevalence of CWP (7). Even though there are conflicting conclusions, there are many more investigators who confirm, rather than deny, the relationship between the mean mass of respirable dust and the development of CWP.The third subject of investigation is the role of quartz in the incidence of CWP. For example, two studies in Great Britain concluded that the quartz content in coal mine dust has no relationship to the prevalence of CWP (8,9). But a study involving 312 Appalachian coal miners revealed that the level of exposure to free silica plays an important role in the development of CWP (10). Once again, the conclusions reached by different researchers are conflicting.Probably the most important factor in the discrepancy among the studies is the variability among different coal mines. A mine operating in an inherently ""dusty"" seam may have a low concentration of respirable dust while a mine operating in a less dusty seam may have a high concentration of respirable dust. This discrepancy is a result of variables such as the effectiveness of ventilation or the efficiency of the water sprays. Consequently, it is very difficult to compare the dustiness of different coal seams by in-mine measurements of the respirable dust concentration. A laboratory test would more accurately characterize a coal seam according to its respirable dust production."

Jan 1, 1988

By M. J. Ferrante

The Bureau of Mines recovered rhenium powder from scrap tungsten alloy containing approximately 25 percent rhenium. Oxidation of the scrap at 950° C separated volatile rhenium heptoxide from tungsten trioxide. Minor amounts of tungsten, iron, and nickel were removed by selective precipitation from a rhenium solution from which was recovered crystalline ammonium perrhenate. Experimentation showed that hydrogen reduction of minus 325-mesh ammonium perrhenate at 1,000° C produced rhenium powder averaging 2.1 microns in size (Fisher Sub-Sieve method). The powder contained <50 ppm of total metallic impurities and 1,070 ppm of total interstitial impurities. Sintered compacts had a density of 95 percent of theoretical. Approximately 96 percent of the rhenium contained in the scrap alloy was recovered.

Jan 1, 1969

By H. C. Fuller

Depletion of iron ore in the Nation&apos;s large deposits has directed attention to other sources. One of these is the titaniferous iron ore of the Iron Mountain, Wyo., area. Tests were made to determine the feasibility of smelting this ore, which contains about 20 percent titanium dioxide (Ti02), in an electric-arc furnace to produce pig iron. Initial tests, which were made in a 30-pound-capacity induction furnace, demonstrated that the iron could be easily reduced to metal and that limestone was a suitable and effective flux. Larger scale tests then were made in a 50-pound-capacity electric-arc furnace to obtain the more detailed information necessary for the planned continuous operation of a still larger arc furnace. The principal facts determined by preliminary batch-smelting studies were that (1) 9 pounds of limestone flux was required for each 100 pounds of ore smelted, (2) expensive coke was not required because coal proved to be a satisfactory reductant (near stoichiometric carbon was optimum), and (3) overreduction, which produced a viscous slag, must be avoided.

Jan 1, 1961

By D. C. Dahlin

The Bureau of Mines investigated the Ketchem Dome tin prospect in east-central Alaska to evaluate the tin resource. The studies included field investigations, mineralogical characterization, and concentration of the tin-bearing minerals. The tin mineralization consists of cassiterite (Sn02), which occurs as grains disseminated in a greisen (quartz-mica) matrixo A bulk sample from the largest and best-developed greisen vein exposed at Ketchem Dome contained 0.51 pct Sn. Concentration of the cassiterite by gravity table methods resulted in a product that contained 56 pct of the tin at a grade of 41.4 pct Sn. The mineralization exposed at Ketchem Dome is typical of greisen found in the area and elsewhere in interior Alaska.

Jan 1, 1987

By E. Morrice

High-purity neodymium, praseodymium, and didymium (a cerium-free mixture of light rare-earth elements) were prepared by electrolysis of the oxides in a medium consisting of the respective rare-earth fluorides and lithium fluoride. The metals were electrodeposited in the liquid state and collected as nodules on a skull of frozen electrolyte. Cells were operated from 1,000° to 1,100° C. The requisite temperature was maintained by passing alternating and direct currents through the bath. Graphite was used for the anodes and tungsten for the cathode. The metal products contained <0.02 percent each carbon and oxygen and <0.025 percent tungsten as major impurities. Analysis of typical didymium metal nodules showed an approximately twofold enrichment in neodymium and praseodymium over their respective concentrations in the cell feed. The lanthanum content of the metal was about one-half its content in the oxide.

Jan 1, 1967

By B. J. Scheiner

The Federal Bureau of Mines has successfully demonstrated an electrooxidation-solvent extraction-carbon adsorption process for recovering molybdenum and rhenium from offgrade concentrates. The flow sequence consists of dissolution of metal values by electrooxidation, liquid-solid separation by thickening, acidification and chlorate ion removal by sulfur dioxide treatment, solvent extraction to concentrate the molybdenum and rhenium, separation of molybdenum and rhenium by carbon adsorption, and metal recovery by crystallization. Molybdenum and rhenium were recovered as ammonium paramolybdate and ammonium perrhenate. Electrolysis of brine-concentrate pulps to generate a hypochlorite oxidizing agent in situ resulted in the dissolution of 98.9 and 99.1 pct of the molybdenum and rhenium, respectively, at an energy consumption of 13.7 kwhr/lb of molybdenum extracted.

Jan 1, 1976

By J. S. Tosh

The Federal Bureau of Mines has investigated the equilibrium of the system potassium carbonate (K2C03) potassium bicarbonate (KHCO3) potassium bisulfide (KHS) carbon dioxide (C02) hydrogen sulfide (H2S) water (H20). Partial pressures of hydrogen sulfide, carbon dioxide, and water vapor were measured at 70° to 130° C. over solutions of 20-, 30-, and 40-percent-equivalent potassium carbonate containing from 20 to 3,000 grains of equivalent hydrogen sulfide per gallon of solution. This study was made to obtain equilibrium data for evaluating the feasibility of using solutions of hot potassium carbonate for removing, hydrogen sulfide from gas mixtures. The equilibrium partial pressure of hydrogen sulfide may be correlated with the ratio of the molal concentrations of the solutes (KHC03) (KHS)/ (K2CO3). The relationship is shown graphically for the 30- and 40-percent solutions. Once this ratio is determined, the partial pressure of hydrogen sulfide can be obtained from the curves. The equilibrium data show that effective removal of both carbon dioxide and hydrogen sulfide can be achieved simultaneously with hot solutions of potassium carbonate.

Jan 1, 1960

1. In 2003, a total of 1,972 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 13.7% of all mining operations. • Bituminous mines comprised 92.5% (n = 1,825) and anthracite mines 7.5% (n = 147) of coal mining operations. • More than 70% of all coal mines were located in three states: Kentucky (29.0%), West Virginia (20.9%), and Pennsylvania (20.2%). • Bituminous coal mines reported the production of over 1 billion coal tons.

Feb 1, 2005

By R. V. Ramani, V. T. Burgos, J. A. McClay

Cost System The cost system reported here is a suite of computer programs which incorporates the logic and information flow structure as outlined in earlier chapters. Specifically, computer programs have been devel¬oped to: 1. compute labor, operating, and capital costs, 2. summarize cost and production data, and 3. compute the minimum acceptable selling price for coal. While the cost system can be executed independently, it is de¬signed primarily for use with the Master Design Simulator and there¬fore must conform to the overall system hardware. The computer model is written in Fortran IV for use with the IBM System 360/370 computers as well as with compatible units such as the Univac 1110 and CDC-6600. For ease in error detection and program modification, the model was constructed with a main routine and eight subroutines. The main routine reads and stores the data necessary for the cost computations and calls the subroutines in logical sequence. The subroutines perform the cost computations and data adjustments for reporting purposes. Each subroutine performs the cost computations for its particular com¬ponent of the cost cycle. The program operations are described in the following narrative outline. Control Subsystem As previously described, the main routine is a passive element, reading and storing input data and directing execution to the active subroutines for cost calculations. Figure 10 is a macro-flow diagram

Jan 1, 1975

By Clinton C. Knox

The Townsite mine, consisting of 40 acres in the town of Cardin, Okla., is in the center of a highly productive part of the Picher-Cardin district of the Tri-State zinc and lead field. Previous to the time of the work done by the Bureau of Mines, the property had been partly explored by churn drilling, and an area-of about 8 acres in the southwestern corner had been exploited by underground workings. The Bureau of Mines investigation had as its object the more intensive development of the northern part of the property where previous drilling had indicated a possible ore deposit of commercial grade. Churn drilling by the Bureau began in September 1942 and continued to February 1943. Twenty holes totaling 4,827 feet of bore were completed. Utilizing the information gained from these drill holes, the Weidman Mining Co., lessee of the tract, sank a shaft and proceeded to the exploitation of the indicated ore bodies.

Jan 1, 1949

By R. V. Ramani, K. V. K. Prasad

"Solution of most engineering problems requires, in addition to vast ·numerical calculations, substantial use of practical judgement and expertise. With advances in applied mathematics and computer technology, the numerical aspects of problem solution have reached a considerable level of maturity; However; it is only .recently that approaches like the expert systems methodology have been developed to ·incorporate the Judgemental aspects as well. For rapid development and prototying of expert systems, expert system building tools or ""shells"" have become widely available. For the expert system developer, identification of the key characteristics of the problem domain and selection of the right expert system tool are of crucial importance. In this paper, the important attributes required in an expert system shell for use in the development or a mine ventilation planning expert system are discussed. These attributes are general in that most engineering problems in mining would have these requirements. Also, the results of an exercise undertaken to evaluate commercially available shells for application to mining engineering problems are presented.INRODUCTIONExpert systems (ES) are interactive computer programs which use high quality specialized knowledge in some narrow problem domain to solve complex problems in that domain. These complex problems lack structured and/or standard ways of solution and involve substantial use of subjective and experience based knowledge. One of the first expert systems was MYCIN, developed in 1974, in which subjective and heuristic knowledge of expert physicians was used to diagnose infectious diseases and provide antimicrobial therapy (Buchanan arid Shortliffe, 1984). Since MYCIN, expert systems applications have appeared in other areas such as mineral prospecting (Gaschnig, 1982), configuration of computers (McDermott, 1982) and structural engineering (Bennett and Englemore, 1979)."

Jan 1, 1989