Search Documents

By H. R. Babitzke, H. Kato, R. E. Siemens

An investigation was made to provide further information for evaluating columbium- hafnium alloys for use as high - temperature structural materials . The columbium- hafnium system was investigated between 700 ° and 2,400 ° C by melting point , thermal analysis , X - ray diffraction , electrical resistivity , and metallographic techniques . The equilibrium diagram is the beta isomorphous type , with columbium tending to stabilize the beta phase . Addition of 60 atomic percent columbium stabilizes the beta phase at 700 ° C. The allotropic transformation temperature of hafnium is 1,750 ° ± 20 ° C. A minimum melting point occurs near 75 atomic percent hafnium .

Jan 1, 1964

By Wilbur A. Haley

The demand on the nation's reserves of high-quality coals suitable for metallurgical purposes is resulting in the rapid depletion of some of the thicker coal beds. These beds are thick enough to permit the use of modern mechanized mining equipment. Many of the thin beds are not being mined at present. In limited areas where the coal is less than 36 inches thick some beds are mined by various conveyor methods. Usually, the room-and-pillar system or some modification of it is used, and often no attempt is made to extract pillars. Consequently, an appreciable quantity of a valuable resource is lost. Many steel companies and coal operators consider reserves of low-and medium-volatile coking coals to be critical, especially in areas where the thin beds are not being mined by modern mining methods. To improve recovery and to promote more-extensive mining in thin beds, methods and devices that are new to American coal mining but applicable to the mining of thin coal beds should be tried. As one of the functions of the Bituminous Coal Mining Section of the Bureau of Mines is to promote improved mining practices and efficiency in the interest of conservation, research in that line is necessary. In 1945 coal planers were observed in operation in Germany by a Bureau engineer member of Solid Fuels Mission to Germany. Planer designs and history of early developments and operations were published. In 1949 an improved planer was again studied by Bureau engineers, and its adaptability to certain conditions in the United States, especially thin beds of friable coal, was considered practicable. After the war the planer was improved, in design and for several years has been operating successfully in the Ruhr. Because of the conviction that the device would be successful, both from the standpoint of conservation and operational prodl1ctivity, under certain conditions in the United States, the Bureau of Mines, through the Bituminous Coal Mining Section, entered into a cooperative agreement with the Coal Division of Eastern Gas & Fuel Associates and Mining Progress, Inc. The purpose of the agreement was to conduct an experiment in modified longwall mining, using a new-type German-built coal plow or planer, known as the Loebbe Habel, supplied by Mining Progress, Inc. The experiment was made to determine if this type of mining equipment operated on a longwall face could be adapted to some of the thinner American coal beds. Such an experiment also would afford many opportunities to study the possibilities and principles of this type of equipment as well as the many factors involved in the mechanical mining of a longwall face.

Jan 1, 1952

By John E. Pahlman

The Bureau of Mines has conducted research on a dual leaching method that offers the potential for the economic recovery of the silver, as well as of the manganese, contained in some domestic manganiferous silver deposits. The method consists of an initial leach of manganese with aqueous sulfur dioxide (S02) followed first by a neutralization rinse, and then by a second leach with cyanide solution for the extraction of silver. Refractory silver in these ores was either (1) intimately associated with the manganese, (2) chemically resistant to cyanide leaching, or (3) rendered inaccessible to cyanide leach solution by the surrounding manganese mineralization. Less than 10 pct of the silver was extracted when minus 2.5-plus 1.3-cm ore pieces were leached directly with cyanide. However, extractions of 25 to 82 pct of the silver and 65 to 96 pet of the manganese were attained in laboratory column-leach tests using the dual leaching method on equivalent-sized ore pieces from seven domestic deposits.

Jan 1, 1987

By Frank B. Fulkerson

A study was made of the economic factors governing silver production in the Coeur d'Alene mining region, Shoshone County, Idaho. Production and other statistics were analyzed. It was concluded that if the rapid rise in the open market price that began late in 1961 continues, greater production of the metal should result from the mines of the Coeur d'Alene mining region. However, the output gain would be limited, because costs per ton of ore mined would rise as production was increased beyond optimum capacity. Advances in the price of silver would increase the size of ore reserves by making some marginal ore profitable to mine and by providing greater funds for exploration projects that might result in discoveries adding to the reserves. Output of byproduct silver from Lead-zinc mining probably will not exceed 4.3 million ounces, judging from the trend from 1946 to 1961.

Jan 1, 1964

By Frank B. Fulkerson

A study was made of the economic factors governing silver production in the Coeur d'Alene mining region, Shoshone County, Idaho. Production and other stat is tics were analyzed. It was concluded that if the rapid rise in the open market price that began late in 1961 continues, greater production of the metal should result from the mines of the Coeur d?Alene mining region. However, the output gain would be limited, because costs per ton of ore mined would rise as production was increased beyond optimum capacity. Advances in the price of silver would increase the size of ore reserves by making some marginal ore profitable to mine and by providing greater funds for exploration projects that might result in discoveries adding to the reserves. Output of byproduct silver from lead-zinc mining probably will not exceed 4.3 million ounces, judging from the trend from 1946 to 1961.

Jan 1, 1964

By A. W. Khair, M. Ahmad

"Bit wear has been proven to have a significant effect on respirable dust generation in coal cutting system. The mechanism of bit wear can be adhesion, abrasion. oxidation, or diffusion. depending on cutting conditions. This paper presents a portion of an extensive ongoing series of studies to better understand the principles of bit wear and dust generation. Used bits collected from underground coal mines were analyzed to identify the basic principle of bit wear in coal and rock cutting. Distribution of weight loss and conical height loss of worn bits were studied and bit wear was divided into four stages according to weight loss. Utilizing these worn bits, Laboratory experiments have been carried out to study the effects of bit wear on coal cutting system and respirable dust generation. An Automated Rotary Coal Cutting Simulator was use to perform the experiments. Acoustic emission monitoring is applied to study the effect of bit wear on fracture formation and dust generation. INTRODUCTIONContinuous miners were introduced in the 1950’s and became the major equipment in underground coal production. Now the larger production in the coal industry has increased the demand for continuous miners and their use. It is well known that serious dust problem is also introduced with the use of continuous miners, especially with recent increase in productivity. On the other hand, legal restrictions are made ·more strict by the Mine Health & Safety Administration for the respirable dust generated by the continuous miners to prevent coal workers from incidence of pneumoconiosis. The incidence of pneumoconiosis depends on dust concentration, exposure time, and physical properties of dust. Of them, dust concentration is the best parameter for the assessment of the risk of pneumoconiosis. Although a lot of research work has been done to reduce dust concentration substantially, some areas are still required further investigation to meet the strict regulations. One of the areas is about bit wear and dust generation. In this area, the principles of bit wear and effect of bit wear on dust generation are major concerns."

Mar 1, 1992

By K. K. Kershner

Sulfide ore concentrates containing cobalt, nickel, copper, lead, and iron were salt roasted and leached on a laboratory scale. More than 95 percent of the cobalt, nickel, and copper was recovered. Heating patterns for salt roasting different concentrates were established. More cobalt, nickel, and copper were recovered from a bulk concentrate composed of a mixture of copper concentrate and iron concentrate. This mixture corresponded roughly with the mixture of these materials in stockpiles in southeastern Missouri. A temperature range of 375° to 400° C. was best for salt roasting. Metal chlorides were leached at a pH of 1 from chloridized charges of concentrates, Although the amounts of cobalt, nickel, and copper extracted were high, the amount of iron dissolved simultaneously interfered with subsequent separation and recovery of these metals. The amount of dissolved iron was reduced substantially by steam treating chloridized charges of bulk concentrate at 300° C. In this way, the ratios of cobalt, nickel, and copper to iron in leach liquors permitted satisfactory separation and recovery of these metals. INTRODUCTION The Federal Bureau of Mines is experimenting with chloridizing reactions.4 5 6 7/ Salt roasting of sulfide ores and concentrates, or their calcines, to form metal chlorides has certain advantages. Chlorides of

Jan 1, 1961

By Spencer P. Howell

One of the important problems in metal mining , tunneling or quarrying is the most economical method of bringing down the ore or rock . The two factors having great influence in determining this are arilling and blasting costs . In considering the efficiency of the explosive used , the diameter of cartridge has always been supposed to play an important part . However , the Bureau's attention has been called to the lack of definite data on the effect of cartridge diameter on the strength and sensitiveness of high explosives . This information is especially valuable to the user of explosives as it assists him to determine what diameter of borehole is most economical . A paper* on "The effect of cartridge diameter on the strength and quickness of high explosives " was submitted to the sub- committee on Drills and Drill Steel of the 24th Annual Convention of the American Mining Congress by Charles S. Hurter , Technical Representative of the E. I. duPont deNemours and Co. In this paper Mr. Hurter points out that the physical characteristics of an explosive most affected by the diameter of cartridge are rate of detonation and sensitiveness to explosion by influence , and that both increase with increase in diameter . As there is a continuing tendency to the use of smaller diameter drill holes in order to lower drilling costs , and as the smaller drill hole requires a smaller diameter of explosive cartridge than larger drill holes do , this paper has been prepared to show the effect the diameter of cartridge will have on the strength and sensitiveness of the high explosives which may be used . Accordingly , the Bureau of Mines , in cooperation with the Institute of Makers of Explosives , has carried out a series of tests to show the effect of cartridge diameter on the strength and sensitiveness of certain high explosives .

Jan 1, 1923

By Byron S. Gottfried

This Bureau of Mines report presents a method for combining the distribution curves at different specific gravities of separation, for a given piece of coal-cleaning equipment and a given raw coal feed, into a single, generalized distribution curve normalized with respect to specific gravity and, therefore, independent of the specific gravity of separation. Illustrative generalized distribution curves, based upon Bureau of Mines collected data on industrial operations, are presented for five different types of coal-cleaning equipment. The well-known concept of probable error is extended to the generalized distribution curve. It is shown that the conventional probable error is directly proportional to the specific gravity of separation. A number of sample calculations, illustrating the use of the generalized distribution curve and generalized probable error, are presented in the appendix.

Jan 1, 1977

By John E. Shelton

Flotation tests were conducted on two samples of copper-nickel-bearing ore from the Harriman area near Rockport, Maine. The samples were taken by Roland F. Beers, Inc., for tests in cooperation with the Federal Bureau of Mines. One sample, analyzing 0.38 percent copper and 0.71 percent nickel, was essentially a disseminated pyrrhotite in hypersthene. Pentlandite, chalcopyrite, pyrite, and millerite were intimately associated with the pyrrhotite. Locked series flotation tests on this sample showed that 87.4 and 73.4 percent of the copper and nickel, respectively, could be recovered in a bulk concentrate that analyzed 3.47 percent copper and 5.34 percent nickel. The copper-and nickel-bearing minerals were collected with sulfhydric collectors in an alkaline circuit. Cleaning the concentrate three times with the addition of pH regulators was sufficient to attain the previously stated grades. The second sample had analyses of 0.31 percent copper and 0.85 percent nickel; talc and hypersthene were the main gangue minerals. Bulk sulfide flotation, made while depressing the talc, resulted in a concentrate that analyzed 2.33 percent copper and 4.70 percent nickel at recoveries of 70.0 and 54.4 percent, respectively. Flotation of the talc followed by bulk sulfide flotation resulted in a nickel content greater than 5 percent. A locked-series test showed that 60.7 percent of the copper and 73.7 percent of the nickel could be recovered at grades of 1.29 and 4.85 percent, respectively.

Jan 1, 1961

By T. H. Jeffers

The U.S. Bureau of Mines has developed porous beads containing immobilized biological materials such as sphagnum peat moss for extracting metal contaminants from waste waters. The beads, designated as BIO-FIX beads, have removed toxic metals from over 100 waters in laboratory tests. These waters include acid mine drainage (AMD) water from mining sites, metallurgical and chemical industry waste water, and contaminated ground water. Following the laboratory studies, cooperative field tests were conducted to evaluate the metal adsorption properties of the beads in column and low-maintenance circuits, determine bead stability in varied climatic situations, and demonstrate the beads' potential as a viable waste water treatment technique. Field results indicated that BIO-FIX beads readily adsorbed cadmium, lead, and other toxic metals from dilute waters; effluents frequently met drinking water standards and other discharge criteria. The beads exhibited excellent handling characteristics in both column and low-maintenance circuits, and continued to extract metal ions after repeated loading-elution cycles. Based on laboratory and field data, cost evaluations for using BIO-FIX technology to treat two AMD waters were prepared. Operating costs for BIO-FIX treatment, which ranged from $1.40 to $2.30 per 1,000 gal of water treated, were comparable with chemical precipitation costs.

Jan 1, 2010

By M. P. Ristenbatt, E. K. Holland-Moritz, K. Metzger

A new post-disaster signalling system for the Bureau o Mines, using through-the-earth EM propagation, was successfully field-tested in the Lake Lynn test mine. Successful detection at an estimated input SNR of -30dB was accomplished using a coherent integration time of 4.46 minutes. The transmitted waveform consisted of a repeating pseudonoise maximal length sequence phase modulating a 1950Hz carrier. The receiver used a sliding-window matched filter, optimal for signal known exactly except for phase and starting time, implemented via a special purpose processor. Parallel processing permits adaptive signalling, where the detection (integration) time is determined by the actual input SNR encountered. This field test demonstrates a trapped miner detection system that is about 36dB more sensitive than a current pulsed system. This increased sensitivity permits some desired combination of increased range, shorter detection time, and reduced transmitter power or antenna-size. The combination of pulse-compression-type-signal, coherent integration, parallel-processing, and output peak-detection algorithms permit implemention of an ultra-reliable detection system. The same combination is compatible with digital Pulse Position Modulation and Emitter position location strategies.

Jan 12, 1983

By A. W. Khair, S. J. Jung

"IntroductionIn a typical incremental loading test, the AE activity increases rapidly in the initial stage of the loading. It is associated with initial closure under compression of favorably oriented cracks already present, together with sliding of crack faces against each other /1/. After the initial stage, crack closure and movement largely cease and the AE activity drops to a barely detectable level /2/. In the final stage of loading test, cracking associated with the onset of inelastic deformation' occurs, and the rate of AE rapidly increases /3/ indicating an increase in the •number of events associated with higher number of microcracks. To understand better primary fragmentation process, Anderson and Ruzzi conducted tests to identify a practical method of monitoring fracture development in rock, as caused by an excavation tool /4/. They proved that a relationship existed between the AE activity, generated during fracturing and the amount of fracture surface area created.A process of fragmentation, demonstrated by conical bits acting orthogonal to the flat surface of block of coal specimen with and without lateral confining pressure is presented here. The monitoring of AE during the fracturing process of rock/coal has been a very useful indirect method in studying fracture mechanism.Specimen PreparationLarge blocks of Waynesburg coal were obtained from a surface mine. These blocks were then out and molded to approximate dimensions of 25.4 x 25.4 x 15.2 'an (10 x 10 x 6 in.). These specimens were instrumented with three strain gages in a 45 degree rosette. One was mounted parallel to the bedding plane direction, another was tinted at an angle of 45 degree from the bedding plane direction and the third was mounted perpendicular to the bedding .plane direction. Each of the three strain gages were set 5.1 an (2 in.) away from the impact point.Typical Test ProcedureIn a typical experiment, the specimen was placed in the confining chamber.Predetermined equivalent in-situ stresses were applied to the specimen by using two sets of hydraulic cylinders. Two 1 in. thick steel plates ware positioned between the sample and the hydraulic cylinders in order to distribute the pressure uniformly over the whole surface of the specimen. The LVDT null position was adjusted with respect to the coal face. After setting the LVDT, the bit and associated weight was lifted to a predetermined height (equivalent to a predetermined kinetic energy) by a win. The three strain gages were balanced using the signal conditioner and the output was recorded by a 6 channel strip chart recorder. The experimental set-up is shown in Figure 1."

Jan 1, 1989

By Alla D. Mah

The heat of combustion of aluminum carbide (Al, C3 ) , obtained directly by combustion calorimetry , was AH298.15 -1,029.6 ± 1.9 kcal / mole . == The heat of formation of aluminum carbide corresponding to this value was AH298.15 = -53.4 ± 2.0 kcal /mole .

Jan 1, 1964

By William K. Tolley

The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from mixed CdTe/CdS scrap produced in the manufacture of thin-film photovoltaic devices. Selective cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. Leaching the scrap for 90 min at 110° C in 2.2NH2S04 under 400 psig 02 yielded 97% Cd extraction; however, cadmium content of the residue ranged between 4% and 7%. Soluble iron was added to the lixiviant to catalyze oxidation of the CdS component. Tellurium and sulfur remained in the leach residue primarily in the elemental form. The iron and tellurium were removed from the cadmium-rich leach liquor by adjusting the pH to 5.3. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Alternative leaching and purification schemes are discussed.

Jan 1, 2010

By C. E. Julihn

In the fall of 1933 a new discovery of gold was made in the old Mojave mining district of California about 70 miles north of Los Angeles. It led to mining operations that have surpassed in their results all reasonable expectations and are of exceptional promise for the future. In less than 3 years, exploration has opened up a number of veins, from some of which a substantial amount of high-grade ore has been shipped, while a large tonnage of milling ore has been disclosed. Two mills, operating on ore averaging better than $12 a ton, will probably produce more than a million dollars worth of gold in 1936, and a considerable increase of their output in the following year is anticipated. While continuance of these operations for a number of years is already assured by ample reserves of ore, future discoveries of still other veins are reasonably possible, as occurrence of gold throughout the volcanic rocks of the district is widespread and the veins now being mined showed little to attract attention at the surface.

Jan 1, 1937

By Glenn C. Reed

This report is one of a series describing mineral investigations within the Missouri River Basin in Montana. The primary purposed of these investigations is to provide information to agencies of the Department of the Interior and others concerned with the planning of Federal power developments in the basin. This report is limited in score to consideration of mineral deposits of presumed inventory value within Gallatin County, Mont. The field investigations were made during the fall of 1948.

Jan 1, 1951

By Frank L. Hess

In the first cart of that little space of time that we have designated as the nineteenth century, chemistry had reached a wonderful stride. Viewed from the present heights attained by the efforts of innumerable chemists with perfected apparatus, mire reagents, air under pressure, water, gas, and electricity conducted to the desk, and. numberless other helps, it seems marvelous that chemists of that day obtained such results. In 1820, about half of the elements had. been discovered; of these discoveries, Swedes had made 15 or more, about once-third of the elements then known and nearly half of those discovered after 1700.

Jan 1, 1939

By Henry G. Dorsett

This report is a description of equipment and test procedures used by the Federal Bureau of Mines in laboratory studies on the explosibility of dusts. The principal tests concern ignition temperature, minimum explosive concentra¬tion, minimum electrical energy for ignition, limiting oxygen concentration, pressure, and rates of pressure rise. As new materials often present unique problems, variations in the general procedure and special tests performed are indicated, The general procedures for handling a dust sample from its receipt at the laboratory to the preparation of the report are described. The repro¬ducibility of the respective tests are shown. A brief history of laboratory studies on dust explosions by the Bureau of Mines and a description of current equipment and test procedures used are presented in this report. Its purpose is to facilitate interpretation of data previously published and those proposed to be published on the numerous mineral, agricultural and industrial dusts that have been studied. Through understanding and interpretation of the laboratory data obtained for the parameters of explosibility, preventive measures can be adopted for alleviat¬ing the hazard of dust explosions arising in manufacturing and processing industries.

Jan 1, 1960

By Robert H. Peters

How can employees be stopped from engaging in unsafe work practices? It is often easier to prevent employees from performing unsafe acts through manipulations of the work environment than through various training or motivational programs. Therefore, it is important that accident prevention programs seek to identify the reasons for the unsafe behavior and to redesign tasks and the work environment (e.g., tools, equipment, physical surroundings) in order to remove employees from sources of harm and to prevent situations from arising that would prompt them to perform unsafe acts. Unfortunately, in the mining industry the work environment is often innately hazardous, rapidly changing, and difficult to predict, making it very difficult, perhaps impossible, to fully protect the employee by environmental manipulations. Therefore, it is important that effective methods be identified for influencing mine employees to work safely. Various strategies have been used to convince employees to avoid unsafe acts and/or adopt self protective behaviors. The intent of this article is to provide guidance to mine operators concerning the use of four techniques for influencing mine employees to work safely: (1) employee surveys, (2) incentives, (3) fear communications, and (4) disciplinary actions.