Search Documents

By A. E. J. Gallagher

This report summarizes the results of flotation studies conducted by the Federal Bureau of Mines on samples of extremely fine-grained lead-zinc sulfide ores. Samples from five ore deposits in the Pine Creek area, Coeur d'Alene district, Idaho, and one deposit in the Metaline district, Washington, were studied at the Albany Metallurgy Research Center to determine the recovery of sulfide lead and zinc by flotation. During the investigation it was found that flotation could be effectively applied to the selective recovery of exceedingly fine-grained lead and zinc sulfide minerals. Separation of galena and sphalerite was obtained on pulps ground through 1,600-mesh, in which most of the particles were smaller than 5 microns. Selectivity and recovery of minerals in this fine size range were enhanced by use of a chemical dye, diphenylthiocarbazone, as a galena promoter. Although unsuccessful on one ore, application of the dye in treatment of two other very fine-grained ores yielded lead concentrates containing over 62 percent Pb at recoveries in excess of 85 percent. More than 55 percent of the lead in these concentrates occurred as particles smaller than 2 microns.

Jan 1, 1961

By James R. Coldwell

Mining and processing cost analyses were conducted by the U.S. Bureau of Mines on massive sulfide copper-zinc and low sulfide vein gold deposit types that may be found in the Ketchikan Mining District. Reserves and recoverable metal values (RMV) needed to make these deposits economically viable were modeled. Methods for estimating ore grades and required RMV are presented. Economic modeling for massive sulfide deposits indicated the RMV necessary for a 15% Discounted Cash-Flow Rate-Of-Return (DCFROR) for an underground cut-and-fill mine ranged from $137/mt for a 6,100 mtpd on-site milling operation to $526/mt for a 450 mtpd off-site milling operation. On-site milling was always less costly than off-site milling. Economic modeling for low sulfide vein gold deposits indicated the RMV necessary for a 15% DCFROR for an open-pit mine, off-site mining operation ranged from $S4/mt at 2,900 mtpd to $71/mt at 360 mtpd, and from $49/mt at 2,900 mtpd to $100/mt at 360 mtpd for an on-site milling operation. Off-site milling was less costly than on-site milling until production exceeded approximately 1,700 mtpd. Then, economies of scale reduced operating costs enough to offset the higher capital costs required for on-site milling.

Jan 1, 1995

By K. J. Miller

A laboratory electrophoresis column was designed to separate pyrite from fine coal by utilizing an observed difference in the electrophoretic mobilities of the two materials in water. The apparatus worked well when tested with synthetic mixtures of coal and pyrite, but some modifications in design and procedure were necessary to provide a sharper separation. After these changes were made, the column was tested with a high-pyritic-sulfur raw coal sample. The column successfully fractionated the sample, removing not only the pyritic refuse, but a siliceous refuse as well. The invest ion demonstrated on a laboratory scale that pyrite and other impurities can be separated from fine coal by electrophoresis.

Jan 1, 1970

By L. E. Green

For shortwall mining to be profitable, the additional capital investment of about $1 million for shortwall roof supports must be offset by decreased total operating costs and/or increased coal production. The Bureau of Mines therefore conducted a demonstration project to compare shortwall and room-and-pillar mining. Daily two-shift production from the bureau of Mines-Beth-Elkhorn Corp. shortwall demonstration n project averaged 975 tons of raw coal, compared with 905 tons from a room-and-pillar unit operating undo r similar conditions. The estimated direct operating costs for the shortwall and room-and-pillar unite were $4.21 and $4.03 pier ton, respectively. The profitability of the shortwall system was found to depend not only on the increased depreciation cost of the powered roof supports and the decreased cost of supplies and materials but also on such factors as the fixed and variable indirect costs and the selling price of the coal. Shortwall mining was demonstrated to be a viable alternative to room-and-pillar mining.

Jan 1, 1977

By A. B. Campbell

The Bureau of Mines is developing alloys using ion implantation as an alternative to bulk alloys that consume large quantities of strategic materials such as chromium and nickel. These alloys are formed at the outer layer of relatively common materials. To more fully understand the corrosion characteristics and physical properties of this outer layer, it was necessary to deter-mine the alloy concentration as a function of depth into the substrate material. Also, since many of the ion-implanted alloys would be utilized at elevated temperatures, it was necessary to determine the diffusion behavior of the implanted element. Proton-induced X-ray emission and inert gas ion sputtering have been utilized to generate composition depth profiles for Fe-Cr, Fe-Ni, and Fe-AI ion implanted alloys fabricated by implanting 25-kev Cr+, Ni+, or AI+ into iron substrates. The data were fitted (utilizing a computer program) with symmetrical Gaussian profiles yielding values for the range and range straggle of the ions. These parameters were then compared with those calculated from theory. Changes in the profiles due to annealing were investigated and values for the diffusion coefficient were obtained assuming diffusion according to Fick's Law. For the Cr+ and Ni+ implantation, the profiles as-implanted agree reason-ably well with theory and exhibit ?norrmal" diffusion characteristics at 500° C. For the Al+ implantation, the profile as-implanted is much broader than predicted and exhibits substantial enhanced diffusion at temperatures up to 500° C.

Jan 1, 1979

By Michael S. Miller

In 1984, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied the 34,050-acre Cow Creek Wilderness Study Area (WSA) in order to evaluate its mineral resources. The WSA, located about 60 miles southeast of Havre, MT, contains sandstones, shales, clays, and coal of Cretaceous age. The Cretaceous rocks have been intruded by ultramafic diatremes. Quaternary glacial, stream, and landslide deposits overlie the older rocks. Claims are staked at five of seven sites favorable for diamonds within the WSA and at additional sites nearby. Although the ultramafic diatremes within and near the WSA contain minerals that are indicators for diamonds, no positive evidence of diamonds was found during this study. An abandoned coal mine, the Shellenberger, is inside the southwest boundary of the WSA. Possible petroleum and natural gas at depth are currently of interest; land within the WSA is leased or under lease application for oil and gas. The WSA contains subeconomic clays, zeolites, gold, silver, platinum group metals, and coal.

Jan 1, 1986

Between 1985-1986, the Bureau of Mines reviewed the mining history and minerals information for areas in and near the San Isabel National Forest to appraise the mineral resources present and determine the types of deposits, and their location in the Forest, that could be mined economically if sufficient demand and metal prices existed. The two major metallic deposit-types that are of national mineral resource significance within the Forest are stockwork- molybdenum (with tungsten and tin) and carbonate-replacement zinc-lead-silver deposits. Historically, small gold placers, gold-quartz veins, silver-quartz veins, skarn iron and copper deposits, volcanogenic copper-zinc-precious metal deposits, and base- and precious-metal veins have been mined. Barite, carbonate rocks, gypsum, other non-metallic deposits, and pegmatites, have also been mined. Sand and gravel, present in large volumes, occurs along and has been mined outside the Forest along the upper Arkansas River valley. Turquoise and gemstones are present in small amounts and are of interest to collectors and jewelers. Geologically, sediment-hosted uranium and copper are present in small occurrences but no resources have been identified. Geothermal resources are related to the Rio Grande rift which parallels the central part of the Forest. Four hot spring areas are present - two of these are within the Forest. Because of the low power requirements of the region, and the presence of other generating facilities, these geothermal resources have had only limited local use. Evaluation of mine models that may be found in the region show that base-metal deposits require a high precious-metal component to be economic. Although molybdenum can be produced at economically competitive prices, there is little demand for the product. Capital costs to start new molybdenum mines would be very high and it is not likely that new mines will be put into production in the near future.

Jan 1, 1989

By Robert C. Johnson

Single crystal whiskers of ZrO2 and TiO2 were grown by solution and crystallization of these oxides in molten baths. Mixtures of Na2B407 and LiC1 were the most suitable growth media for zirconia. Sodium borate alone and Na2CO3 plus SiO2 were best suited for titania. The solubilities of zirconia and titania in molten sodium borate were determined, Whether zirconia whiskers were dendritic or nondendritic depended on the temperature used. The best single crystal whiskers were grown below 1,100° C. Titania whiskers always grew as single crystals. The tensile strengths of zirconia and titania whiskers were about 15,000 psi and 50,000 psi, respectively. Modulus of rupture was about 49,000 psi for zirconia whiskers and 75,000 psi for titania whiskers. Chemical analyses showed the zirconia and titania whiskers to be pure. The zirconia and titania whiskers were shown by X-ray analysis to be, respectively, baddeleyite and rutile.

Jan 1, 1965

By J. M. Stuve

Low temperature and high-temperature calorimetric measurements were made by the Federal Bureau of Mines on high-purity samples of Re02(s) and Re03(s) to determine heat capacities and enthalpies. The temperature range of heat capacity measurements was 5 to 310 K for Re02 and 8 to 309 K for Re03. High-temperature enthalpy measurements alone were determined for pure Re207(s,1). The derived standard entropies are S°298 = 11.43±0.01 cal/deg mole for Re02(s) and S298 = 16.55±0.02 cal/deg mole for Re03(s). High-temperature enthalpy equations expressed in calories per mole are as follows: Re02 (s) , H-H298.15 = 16.002T + 1.600 X 10-3T2 + 3.522 X 105T-1 - 6,095 (298 to 1,400 K); Re03 (s) , H-H298.15 = 20.293T + 3.238 X 10-3T2 + 3.950 X 105 T-1 - 7,664 (298 to 1,000 K); Re207 (s) , H-H298.15 = 38.437T + 10.309 X 10-3T2 + 4.315 X 105 T-1 - 13,824 (298 to 413 K); Re207 (s) , H-H298.15 = 30.181 + 17.713 X 10-3T2 - 10,612 (413 to 600 K) ; Re207 (1) , H-H298.19 = 66.101T - 10,092 (600 to 700 K). Gibbs energy of formation (?Gf°) data and related functions over the temperature ranges investigated are tabulated for the three oxides.

Jan 1, 1976

By William E. Dennis

"At the request of Philip S. Hoyt, the Eagle Mountain fluorspar deposits in section 35, block 68, Texas & Pacific Railroad Survey No. 9, were examined by an engineer3/ of the Bureau of Mines during March 1943: As a result of this examination; a preliminary program of trenching, sampling and core drilling by the Bureau of Mines was begun in. June 1943.4/ Eight deposits were explored.The Federal Geological Survey mapped the properties and furnished geologic information throughout the program, while the Texas .Bureau of Economic Geology6/ made preliminary maps that facilitated planning the exploratory work on section 35.The eight deposits explored by the Bureau of Mines are in block 68, Texas & Pacific Railroad Survey No. 9, Hudspeth County, Tex., approximately 7-1/2 miles south of. Hot Wells and 12-1/2 miles south of Allamoore, which is 10 miles west of Van Horn and 20 miles east of Gierra Blanco on U. S. Highway 80(fig. 1). A graded gravel road, built by the Public Roads Administration, leads from Hot Wells to the deposits in section 35, and there are unimproved roads, passable,by automobile, to all the other deposits.Carload shipments can be made to and from Hot Wells on the Southern Pacific Railroad, and complete railroad facilities are available at Allamoore on the Texas & Pacific Railroad.Van Horn and Sierra Blanca are the only local source of labor and. supplies. The prevailing wage for common labor is 60 cents an hour. Living accommodations are obtainable in Horn and Sierra Blanca.No electric power lines pass near the deposits. Diesel and gasoline motors are employed to furnish power for mining and milling operations.Two recently 'drilled water wells on section 35 furnish water for the mill. Other wells will be drilled if the present supply is inadequate for prolonged Peak operation.The properties lie in the foothills on the northeast side of the Eagle Mountains at 5,500 feet altitude. The Eagle Mountain Range rises sharply from a broad, flat valley known as Eagle Flat. Eagle Peak, the highest in the range, has an altitude of 7,510 feet. In the vicinity of the fluorspar deposits the topography is moderately reliefs ranging from 50 to 300 feet."

Jun 1, 1946

By James A. Wasson

The Mitchell and Berea sands were cored and logged in Fred Link well K-l, Lower Newport field, Washington County, Ohio. Core and reservoir fluid analyses and available field data were studied to determine if these sands could be successfully waterflooded. The results of the study indicate that there is insufficient oil in place to form an oilbank in either the western Mitchell pool or the Berea sand, and that no commercial recovery of oil by waterflooding can be obtained in these reservoirs.

Jan 1, 1967

By W. H. Ode, W. A. Selvig

"INTR0DUCTIONAccording to the Standard Specifications for Classification of Coals by Rank of the American Society for Testing Materials (A.S.T.M. Designation: D388-38).1/ high-volatile bituminous coals, subbituminous coals, and lignites are classified on the basis of calorific values on the ""moist"", mineral-matter-free basis. The moist basis refers to coal containing its natural bed moisture but not including visible water on the surface of the coal. It is assumed that the natural bed moisture of coal in the ground represents the moisture-holding capacity of the coal when in equilibrium with air at approximately 100 percent relative humidity. This moisture is sometimes referred to as inherent moisture as opposed to extraneous moisture, which wets the surface of the coal.To simplify procedures for determining the moisture-holding capacity of coal it is assumed, for all practical purposes that the moisture content of coal when brought to a standard condition of moisture equilibrium in an atmosphere of 97 percent relative humidity and 300 C. represents the bed moisture of the coal. The A.3.T.M. specifications provide that this condition of moisture equilibrium shall be obtained by bringing the coal to a standard condition of moisture equilibrium at 300 C. in a vacuum desiccator containing a saturated solution of potassium sulfate (97 percent relative humidity) according to the procedure proposed by Stanfield and Gilbart. 4/ No mention is made in the specifications for bringing partly air-dried samples to their natural bed moisture condition probably because of the hysteresis effect that has been noted by various investigators. 5/ In this connection it has been found from sorption studies that the adsorption and desorption curves for lignite are not entirely reversible. The hysteresis effect has been explained by some investigators as resulting from shrinkage of the lignite during drying, which causes a collapse of some of the capillaries, so the dried lignite cannot take up as much water as it held originally."

Apr 1, 1953

By H .. B. HUMPHREY, F. E. Cash

Sixty-one fatal accidents were reported in the mines of Alabama during 1930. This number is a decrease of 15 per cent as compared with 1929; however, production was 13 per cent and the man-hours worked were 16 per cent less than in the previous year. There were 21,731 men employed inside and 3,386 outside. Table 1 gives the comparative rates per million tons and per million man-hours for the United States and for Alabama for 1929 and 1930. These rates are based on figures published by the State and by the United States Bureau of Mines, with preliminary figures for 1930. (These sources of data are used throughout this paper.)

Oct 1, 1931

By Raymond B. Ladoo

The uses of talc are many but are not, in general well known or fully developed within the last decade several companies have realized the possibilities of greatly increased use and have intelligently proceeded to develop some of the fields which seemed most promising. This has had a tendency to lift talc from the obscurity in which it had existed for years, but the work is only started and much remains to be done. Considerably more attention has been paid to the technology and utilization of talc in Germany and Austria than in this country, despite the fact that the United States produces 65 of the world's talc and Germany and Austria combined but 5.4%. In the "Bericht,uber die tatigkeit des verbends der talcum-interessenten in Oesterreich-Ungarn" (Proceedings of the Austro-Hungarian Talc Association), for the years 1912 and 1913, many notes upon new uses appeared, together with suggestions as to further development of old uses. Aside from a few notes on the use of tar in paper, little has been published in the English language upon this subject. By recent action of the Talc and Soapstone Producers Association (U.S.A.) funds for research into the properties and uses of talc have been made Available and it is hoped that markets will be materially broadened a a result of this work.

May 1, 1920

By Michael R. Kennedy

This report describes the demonstration of longwall mining in a seam dipping 27 to 34'. Equipment was selected on the basis of capability, compatibility, and co t. Snowmass, Bureau of Mines, consultants and manufacturers were involved in the selection process. The equipment arrived in early 1981, prior to completion of development for the first panel; therefore, the equipment was operated on the surface for training. The surface training paid off with a fast, efficient installation and start-up of the face. The longwall equipment operated very well on the steep pitch with an average equipment downtime of 21.9[9]. Coal handling outby the face was a problem which caused an additional downtime of 19.5%. Development for the panels proved to be the major problem in the economics of longwall mining on a steeply dipping seam. During the first 9 months of operation the longwall averaged 71.9 TPMS and development averaged 0.6 TPMS for an overall average of 14.1 TPMS. Had mining continued, timing of development would have been another major problem. Monitoring of subsidence, pillar stability and shield loading was done in connection with mining, but little useful information was gained from the monitoring.

Jan 1, 1987

By Oliver Q. Leone

Three electrorefining cells were designed to investigate various factors associated with the electrorefining of reject - grade titanium sponge . Operation of the cells provided information on cell design as well as on how design and operating variables affected the quality of the titanium product . A sodium chloride - titanium chloride electrolyte was used , and the electrolyte chambers had capacities ranging from 400 to 3,500 pounds of molten salt . Major factors investigated were electrolyte composition , temperature and useful life , effect of various cathode shapes and materials of construction , methods for removing cathode deposits , effect of current density and cell potential , and the mechanics of deposit growth and crystal morphology . One of the cells was in intermittent operation over a 4 - year period and produced 2 tons of refined titanium . A product with a hardness of 80 or less Bhn (Brinell hardness number ) was consistently and easily obtained . Some metal with a hardness of less than 60 Bhn was produced . In one of the cells in which the electrolyte was held at operating temperature with an internal heater an ac input of 25 kw maintained 3,500 pounds of electrolyte at 850 ° C , but with an external heater 35 kw was required to maintain 400 pounds at 850° C.

Jan 1, 1964

By D. J. Parker

State governments are increasing their efforts each year toward promoting the safety of miners .. Accidents underground are being avoided and mines made safer by means of revising and adding to their mining laws , by enforcing them through mine inspection departments , and by hearty co - operation with other agencies working miners ' safety . The U. S. Bureau of Mines is glad to testify to the co -operation that it receives from State mining departments in its safety work ; reports of the field mining engineers of the Bureau bear witness almost daily to the efforts of the States toward safety in mining . * This Through the courtesy of Mr. William Ogilvie , District State Wine Inspector of District No. 2 , with headquarters at "cAlester , Oklahoma, the Bureau has been furnished with a copy of a letter sent to various mining companies of Mr. Ogilvie's district in Oklahoma, relative to safety in Oklahoma mines . letter shows both the vigorous efforts which the State of Oklahoma is making toward increased safety in mines , and the recognized value of the types of electric cap lamps approved by the U. S. Bureau of Mines as " permissible " for use in gaseous mines ; it is accordingly reproduced in part : "hen during my first inspections of several coal mines in the district I found gas , or fire- darp being given off more or less constantly from the freshly cut coal at numerous points throughout the mines , I became uneasy relative to safety conditions , and am still considering your safety from many angles , but I am more concerned about the gas given off and the coal dust produced daily, than any other factor at the present time .

Jun 1, 1922

By Jeffrey Shawn Peterson

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. In response, the National Institute for Occupational Safety and Health (NIOSH) conducts research to reduce the noise emission of various underground coal mining equipment, an example of which is a roof bolting machine (RBM). After the removal of coal or rock, the remaining strata may be subject to fall, either from overhead (the roof) or from the side (the rib). One method used in underground coal-mines to prevent failures requires the installation of roof bolts. The roof bolting machine operator trams the machine to the required location, drills a hole into the strata, and then installs a roof bolt, supporting the roof or the rib, as the case may be. Field studies support the premise that, on average, drilling noise is the loudest noise that a roof bolting machine operator would be exposed to and contributes significantly to the operators? noise exposure. NIOSH has determined that the drill steel radiates a significant amount of noise during drilling. NIOSH is developing bit and chuck isolators to reduce vibration, and thus noise radiation of the drill steel, with the longer-term goal of reducing roof bolting machine operator noise exposure. Laboratory testing has shown that operator ear sound pressure levels may be reduced by 3 to 7 dB(A), depending upon the test configuration and drilling media.

Jan 1, 2009

By C. H. Schack, K. C. Dean

An investigation was made to devise and evaluate a flexible flotation method for beneficiating typical tactite types of calcareous scheelite - bearing ores ; these scheelite - bearing ores are available in large tonnages in deposits containing 0.2 to 0.3 pct tungsten trioxide . The objective was to achieve a high recovery of the tungsten in concentrates , containing a minimum of 10 pct WO3 , that would be suitable for chemical processing into high- quality synthetic scheelite . The principal problems encountered and resolved by bench- scale flotation tests on ore samples from five different deposits were to define the conditions and reagent combinations essential for ( 1 ) achieving selective flotation of a small amount of scheelite from a large amount of calcite and ( 2 ) controlling the effect of small amounts of calcium , magnesium , and iron salts in the ores and water used . The flotation process was evolved from batch tests and continuous runs in a pilot - scale mill with a capacity of 100 lb per hour . The flotation process comprised ( 1 ) removal of sulfide minerals , ( 2 ) conditioning the residual ore pulp with sodium carbonate , quebracho , and trisodium phosphate , and ( 3 ) rougher flotation and single - stage cleaning of a scheelite concentrate . In a pilot plant run , over 91 pct of the tungsten was recovered from ore containing 0.27 pct WO3 , in a concentrate containing 11.2 pct WO3 .

Jan 1, 1964

By M. S. Seehra, R. S. Pandurangi

"INTRODUCTION Silica and kaolin (a layer aluminosilicate) are among the major constituents of most coal mine dusts.' Whereas kaolin is cytotoxic in vitro but nonfibrogenic in vivo in humans and experimental animals,2-4 the cytotoxic and fibrogenic potential of silica is rather well established.5 Wallace and co-workers 6-8 have studied the cytotoxic potentials of both native and surface-modified silica and kaolin and inferred that retoxification is slow in the case of occluded silica vis-à-vis native silica. Recent epide¬miological studies indicate that silica concentration alone in a mine dust, as determined by transmission IR spec¬troscopy (TIRS), does not correlate well with the pro¬gression of coal workers' pneumoconiosis. 9 This obser¬vation has led to the suggestions that silica particles occluded by clays such as kaolin may not be fibrogenic. This proposal requires accurate estimations of kaolin, silica, and occluded silica. The current method of silica analysis in a mine dust sample employs TIRS of the 797- cm -1 band of silica, although its accuracy, as well as that of x-ray diffraction studies, is no better than 25 % , even in a laboratory-generated dust.° In this paper we have employed the techniques of diffuse reflectance spectros¬copy (DRS) and photoacoustic spectroscopy (PAS), in conjunction with an FT-IR spectrometer, for the quan¬titative determination of silica in laboratory-generated silica-kaolin mixtures.One of the main advantages of DRS and PAS is that, in these techniques, problems arising from sample prep¬aration of the KBr-based disks used in TIRS are avoided. There are, however, several other considerations (e.g., particle size effects and saturation phenomenon) which complicate the use of DRS and PAS for quantitative work. 10-25 In this paper, we have carried out a systematic comparison of the quantitative abilities of the two tech¬niques, as applied to the silica-kaolin mixtures, with par¬ticular attention to the saturation behavior of several bands with different absorption coefficients. In particular, we show that a weaker band for silica at 1875 cm-1 is suitable for quantitative purposes, and that quantitative accuracy is higher in DRS than in PAS. Details of this work are given below."

Mar 1, 1992