Search Documents

By L. E. Schultze

The Bureau of Mines devised a technique to recover a Zn-Pb concen-trate from a geothermal brine. More than 99 pct of the Zn and Ph was precipitated by treating the brine with H2S and controlling the pH with lime. Recycle of the sulfide precipitates increased crystal size and resulted in easily filterable products. A typical sulfide precipitate contained 53 pct ZnS, 8 pet PbS, 24 pct MnS, and 15 pct FeS. Addition of sulfide as FeS or CaS was not effective in precipitating Zn and Pb, but Zn in the brine was selectively removed with a strongly basic ion-exchange resin. A proposed flowsheet for metals recovery is discussed.

Jan 1, 1985

By R. H. Jefferson

This Bureau of Mines report describes a series of rapid wet chemical methods for the analysis of blast furnace slags. A "complete" analysis for total iron, manganese, silica, lime (calcium oxide), magnesia (magnesium oxide), sulfur, and mixed oxides (R203) can be routinely performed in less than 3 hours. These methods were employed as the analytical control procedures for the Bureau's experimental blast furnace operations and have been satisfactorily applied to the analysis of other slags and calcareous materials.

Jan 1, 1974

By J. A. Lamonica

The Bureau of Mines studied a pulsation damping device designed to smooth pulsating flow in personal respirable dust samplers. The effect on the pulsation dampener efficiency of six parameters was investigated, as follows: Volume, diaphragm elasticity, diaphragm area, center orifice area, inlet-outlet orifice area, and geometry (LID ratio). The results indicate that volume pre-dominates in determining snubber efficiency, while the other parameters become important at small volumes. Geometry has no effect on snubber efficiency. Criteria for an efficient pulsation dampener construction were obtained.

Jan 1, 1971

By C. J. Cohen, L. A. Dahners

"SUMMARYA method has been developed for surveying, drill holes without lowering into the hole any surveying equipment other than an etch tube. The orientation of the rods at the collar of the hole is maintained as the etch tube is lowered. The attitude of the etch ellipse in depth with respect to the rod orientation at the collar can then be observed. This relationship permits the bearing of the hole in depth to he calculated. The rod orientation is maintained during the lowering by means of a pair of alinement clamps. One clamp is fastened to the top of each rod as the rod is coupled and is removed when the alinement has been transferred to the other clamp at the top of the next succeeding rod. A particular advantage of this survey technique is that surveys can be readily made in magnetic country rock.PRINCIPLE OF THE TECHNIQUEAn axial lamina of the column of drill roes is the lamina in which one fiber would be the centerline of the rods. In the new survey technique, the rods are fed into the hole in such a manner that the axial lamina of each successive rod maintains its position at the collar of the hole. In depth, as the rods bend in following the drill hole, the axial laminae also bend. The lamina that was originally vertical will, in general, be tilted away from the vertical. The trace of this lamina is marked on the glass etch tube before the tube is lowered in the hole. The axial lamina that becomes vertical at the survey station is recognized as that axial lamina which contains the long axis of the etch ellipse. The angle between the lamina originally vertical and the lamina vertical at the survey station is thus measurable. When the vertical axial lamina at one survey station has been determined by the etch ellipse at that station, angle R between this lamina and the vertical axial lamina at the next survey station becomes measurable also. By moans of angle R, and dip angles D1 and D2 at the two stations, the change in bearing (z) of the drill hole between the two stations can be calculated."

Aug 1, 1944

By Robert W. Smith

The Bureau of Mines is engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies are designed to provide basic thermodynamic information of high accuracy, facilitating the theoretical study of flame and combustion phenomena. This report is the fourth of a series4/ presenting results of the study for particular fuel-oxidant systems. These calculations have as their objective the evaluation of the constant pressure flame temperatures of methane-air, propane-air, and ethylene-air mixtures for a range of pressures.

Jan 1, 1953

By E. D. Gardner

This paper discusses prospecting for lode gold and lists the principal lags and. regulations pertaining to locating; lode claims on public lands. It is a preprint of a part of a bulletin being prepared by the United States Bureau o Mines entitled "Equipping, Developing and Operating Small Gold Mines". The increased interest in gold mining manifested during the past few years (1932-1935) bas stimulated prospecting. Many adventurers have taken to the field to search for now gold deposits. A. large percentage of them have had no previous experience in prospecting for lode gold; this paper has been written with the tope that it might assist these newcomers.

Jan 1, 1935

By John H. Soulé

"Bureau of Mines engineers3/ examined the White Eagle fluorspar mine on September 3, 1943, and again on February 17, 1944. The examinations led to a proposal for the exploratory project upon which this report is based. The project, which was supervised by the author and P. L. Russell, was started on April 6, 1945, and completed on June 26, 1945.Geologists4/ of the Federal Geological Survey examined, mapped, and reported on this property prior to initiation of the Bureau of Mines project.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. H. S. Dean, assistant director.Special acknowledgment is due to C. H. Johnson, Rolla, Mo., Division, Mining Branch; to W. R. Storms, mining engineer in charge of the New Mexico field office; and to J. H. Hedges, chief of the Tucson, Ariz., Division Mining Branch. Acknowledgment is owed, also, to Robert Trace and Howard Rothrock, of the Federal Geological Survey, for help in mapping the surface and in logging drill cores.The White Eagle claim is in the east-central part of sec. 34, T. 19 S., R. 9 W., Cooks Peak Mining District, southeastern Grant County, New Mexico. The property is reached from Deming, N. Mex. by taking the paved U. S. Highway No. 260 northwestward for 13 miles to the junction with State Route 61. State Route 61 is a graded but unpaved road and is followed northward for 8 miles to a junction with a poor dirt road, which is followed eastward for 11 miles to the mine. Silver City, N. Hex., is about 50 miles northwest of the mine and may be reached by several routes.The White Eagle patented claim was owned by L. H. Duriez of Vanadium, N. Mex., W. D. and W. A. Howard of Deming, N. Mex., Alvan N. White of Silver City, N. hex, and: Mrs. E. M. Saunders of Los Angeles, Calif. D. P. McCabe of Lordsburg, N. Mex., a former lessee, has recently contracted to purchase the property.The White Eagle claim was located about 1920 and was patented in November 1933. It was leased to Cooper Shapley of Deming, N. Mex., in July 1933; to General Chemical Co. from August 1938 to May 1940; to Antonio Cristo from October 1940 to the fall of 1942; and f is ally it passed into the hands of D. F. McCabe of Lordsburg, N. Mex., in May 1945.Approximately 25,000 tons of fluorite ere containing about 65 percent CaF2, have been mined and shipped from this property.5/ Most of this ore was mined by Cooper Shapley and the General Chemical Co. and shipped to the General Chemical Co.'s La Purisima mill at Deming. No exact data on production are available."

Jul 1, 1946

By B. W. Naugle

A small-scale laboratory coke oven similar to those described by Swiniarski, Cryan, and Altieri and Fuchs, Sandhoff, Taylor, and Gauger was built by the Bureau of Mines in 1943. Tests made since that time have indicated that such a small oven is of questionable value in predicting the coking pressures to be expected in commercial coke ovens. This summary of the work done has been prepared at the suggestion of the Advisory Committee to the Bureau of Mines-American Gas Association Survey of Carbonizing Prop¬erties of American Coals.

Jan 1, 1948

Develop a simple and economical technique for determining the absolute stresses and the change of stress on the surface of roofs, floors, or walls in miners. Approach Use a commercially-available, permissible, Whittemore-type gage to determine the stress at the surface of a mine opening and to monitor any stress changes that might take place. How It Works The following equipment is used: ? One steel templet (for laying out a 60° rosette on the: rock surface). See first photograph. ? One 3/8-inch rock drill bit for drilling holes for the rosette pins. ? Six stainless-steel rosette pins. ? One Whittemore-type mechanical strain gage. ? One drill (not shown). ? Epoxy for cementing the rosette pins. ? Tape to hold the pins while the epoxy sets. The following procedure is used to determine the absolute stress on the rock surface. 1) Spot the location of the rosette pins with the templet. 2) Drill the pin holes and set the pins with epoxy cement. 3) Measure and record the distance between the pins across three diameters of the rosette with a 10-inch Whittemore-type gage. See diagram. 4) Drill a 1 1/2-inch diameter hole in the center of the

Jan 1, 1981

By R. Van A. Mills

This preliminary paper is intended to answer briefly some of the inquiries coning to the Bureau of Mines regarding the so-called "paraffining", of oil wells and methods of preventing and remedying that trouble. The increased difficulties in operation and the losses of production caused by the deposition of gummy and waxy hydrocarbons, commonly called paraffin, in the wells, tubing, other pumping equipment, and in the pores of the productive sands, have long been recognized but the trouble has not been overcome. The nature and causes of the trouble, together with some of the possible methods by which it may be diminished or overcome, are outlined below. Character of the Peraffining Materials. The so-called paraffin that collects in oil wells end in the pores of the oil-producing sands immediately around the wells, is generally made up of amorphous wax or uncracked paraffin, asphalt, or other gummy hydrocarbons mixed with more or lees water, oil, and inorganic silt. Some of the samples of this "paraffin" collected from oil wells in different fields and examined by the Bureau of Mines contain as mach as 20 per cent by weight of water and inorganic silt, whereas other samples are composed entirely of waxy hydrocarbons and oil. The inorganic silt accompanying this "paraffin" is mostly fine sand, clayey materials, common salt and finely disseminated precipitates of calcium and magnesium carbonates. Sulphates of calcium, barium, and strontium are less common constituents of the "paraffin."

Jan 1, 1923

By D. M. Soboroff

Etchants containing hexavalent chromium and sulfuric acid are used in a variety of surface-finishing operations. When the resultant spent solutions are discarded, substantial quantities of chromium are lost and pollution prob¬lems are created. To minimize the undesirable environmental effects while improving metal and minerals recycling technology, the Bureau of Mines is conducting research on a method for the economic inplant recycling of these waste etchants. Trivalent chromium, produced when the etchant reacts with a sub¬strate, is oxidized in the anode chamber of a diaphragm cell; other metals, dissolved during the etching operation, are transferred to the catholyte. When waste brass etchants are treated in this manner, all of the trivalent chromium is oxidized and more than 40 percent of the copper and zinc is removed. Similar copper removal and chromium oxidation are achieved with waste printed circuit board etchants and rinse waters from plastic etching operations. The electrical energy needed to regenerate 1 kg sodium dichromate is less than 9 kwhr. Regenerated brass etchants evaluated by two companies equaled or exceeded the performance of fresh etchants.

Jan 1, 1979

By E. F. Foerster

The Bureau of Mines used a diphenyl ether calorimeter to determine the heat contents of natural and synthetic blast-furnace slags. For solid slags, enthalpy (HT-H298) at 1,448° to 1,680° K ranged from 282.1 to 348.5 cal/g (±3 percent); liquid slag values were 400.1 to 514 cal/g (±3 percent) in the temperature range between 1,626° and 1,890° K. Experimental results for liquid slags were 14.3 to 16.2 percent higher than the enthalpies calculated from thermodynamic tables; values for solid slags ranged from 5.3 percent lower to 3.9 percent higher than calculated values. Experimental results for liquid synthetic slags ranged from 14.9 to 24.3 percent higher than the calculated enthalpies; values for solid synthetic slags were from 1.0 to 3.4 percent higher.

Jan 1, 1967

By Earl R. McMillan

"Coal washing commands the thoughtful attention of a steadily incre in number of people. Clean coal is not merely a luxury but is rapidly becoming a necessity in some industrial operations.Coal seams in the Northeast are rarely free from ""bone"" and shale or clay partings which vary from a fraction of an inch to several feet in thickness. Nearly all of the coal measures are folded and faulted, the coal seams dip at various angles, and in some cases are badly broken. In mining these seams fragments of the roof and floor, as well as partings of impur-ities within the seams, unavoidably become mixed with the coal, so that the raw coal as it comes to the surface often contains as much as 50 per cent, by weight of waste.At the Bureau of Mines experiment station at Seattle, the washing of this coal in order to improve it for commercial use has been studied. Since the process of coal-washing depends upon differences in specific gravity between the clean coal and, its associated impurities, the first problem undertaken was that of determining the specific gravity of the clean coal and of each parting of impurity contained in a large number of representative seams.It was found that the freshly-mined coal is practically saturated with water, this being observed in determining the effect of moisture content upon the specific gravity of the coal particles, selected from samples of coal varying from low-grade subbituminous up to semianthracite, all of which are found in the State of Washington. The specific gravity values determined for the cleanest particles varied from 1.28 to 1.35; in general, the higher the rank of the coal the hither the specific gravity."

Nov 1, 1920

By George L. Gates

The Bureau of Mines studied pressure-buildup data from a number of California gas wells to determine if the reservoir properties calculated from these data correlated with field-observed reservoir properties. Pressure-buildup curves from 24 wells showed distinct changes in slope, indicating changes in permeability of the reservoir rock. Calculated distances from the wells to indicated permeability changes were in fair agreement with distances deter-mined in the field. Pressure-buildup curves from three wells had more than one distinct change in slope, indicating multiple permeability changes. Thus field data supported the theoretical relations used to calculate reservoir properties from pressure-time relations measured in gas wells.

Jan 1, 1967

By D. N. Tallman

The electrokinetic properties of MgO have been utilized to simultaneously filter suspended solids and remove trace amounts of dissolved heavy metals from synthetic mine water. Greater than 95 pct removal of metals from influent at neutral pH containing 1 to 6 mg/L of dissolved Cd, Cu, Mn, Ni, and Zn can be routinely achieved by filtering through a granular bed of MgO at flow rates typical of rapid sand filtration (0.3 cm/s). Filtrate concentrations of most metals can be maintained below 0.1 mg/L for 160 bed volumes or more loading. The more mobile metals (those with larger solubility products) are more difficult to remove, and are strongly bonded to the MgO granules so that chemical stripping with chelating agent is required to clean the bed. Less mobile ions are easily removed by the filter and are effectively stripped by conventional filter backwashing. The fraction of metals recovered by chemically stripping the loaded MgO filters correlates to the zero points of charge of the metals. This process may be applicable to removal and recovery of trace amounts of heavy metals in mine drainage that is partly neutralized by liming. Also, since many of these metals are critical and strategic, the technique can be adapted not only to recycle process water from mineral and milling waste streams, but also to reclaim their metal values.

Jan 1, 1986

By Vernon C. Allison

The explosibility of coal dust has long been recognized by competent investigators as constituting one of the dangers of mining coal and in the use of pulverized coal as a fuel in industrial plants. The Bureau of Mines has carried on extensive series of experiments dealing with this subject, and has not only developed methods for the practical prevention of this danger, but in the, course of these experiments has developed a standard method of determining the relative explosibility of coal dusts and other organic dusts.3 Oil shale contains compounds 'of carbon and hydrogen that are either of a petroleum nature and are strongly ,adsorbed upon the incombustible part of the shale, or else are present in the shale as a compound ("kerogen") which has the property of changing into petroleum-like products when acted upon by heat. The oil shales may contain varying amounts of the organic matter, ranging from a trace to more than 66 per cent, depending upon their richness; therefore, it is important to know whether the dusts formed in mining and handling these oil shales are explosive when mixed with air and if so, to indicate remedial measures. This paper gives the results of explosibility tests of several pulverized oil shale's, selected as being typical of those which in the future may be used in commercial shale-oil production test on a sample of typical Colorado oil shale has been., published in an earlier paper.4

Jan 1, 1926

By C. Van Dyke, K. Van Dyke, J. Gutierrez, C. Nowack

"Using propidium assay and flow cytometry, we examined how silica exerts its toxicity toward phagocytic cells employing the human neutrophil as a model. This toxicity appears to be associated with calcium bound to silica. Once the silica with calcium is phagocytized, the extra calcium causes the death of the cell. Using ""Ca we found that 6 to 10% of millimolar calcium is bound to milligram amounts of respirable-sized silica (diameter of 5 µ.m or less) at physiological pH. If the silica particles arc coated with an organosilanc (Prosil 28). calcium binding is decreased by 60% as is cell death. Pretreating with INDO IAM (a chelator of intracellular calcium) reduces the cellular death by 80%. Nonfibrogcnic particles- polystyrene beads or coal dust-produced 10% or less cell death in a 4-h period. Silica with no added, external calcium appears to exert toxicity to neutrophils; however, pretreating cells with EDT A decreases cellular death to the level of nonfibrogcnic particles. Chronic toxicity with silica-calcium appears similar to the chronic toxicity in gout where particles cause a cycle of inflammation. c 1993 Academic Press, Inc.Silicosis is an occupational disease caused by the inhalation of fine particles of silica, usually between 0.1 and 5 µ.m in diameter (1). A recent hypothesis explaining silica's toxicity suggested that surface free radicals caused damage to cells (2). This explanation appears doubtful, however, since the addition of silica to water, such as that found in biological systems, quenches free radicals; also, such a hypothesis does not provide basis for a persistent inflammatory pattern that lasts for years. Kane et al. (3) proposed that silica's toxicity resulted from an excessive concentration of calcium ions within the phagocytic cell (macrophages). However, the mechanism that was capable of linking silica to an excess of intracellular, ionic calcium was not explained. The surface of silica is certainly involved because covering the surface with polymers or phospholipids decreases silica's toxicity (4-6).When silica is engulfed by macrophages platelet activating factor and leukotrienes are produced (7, 8). This is the same inflammatory pattern produced by phagocytic cells exposed to the calcium ionophore A23187 and ionic calcium. How could silica be acting like A23187? Perhaps calcium binds to silica extracellulary and then is released intracellulary following phagocytosis; the latter process, in a sense a ""piggy back"" process, would permit activation of inflammation and cell death mechanisms."

Nov 1, 1995

Monitoring systems can have numerous uses in the mine. They can aid in the efficient management of the mine by providing environmental trend data, production and maintenance control, and communications. In some cases, they can provide justification to petition the Mine Safety and Health Administration (MSHA) fog a variance of one of the mandatory safety standards. They may also increase the gross revenues of the mine by increasing the amount of coal produced or increase profits by reducing the cost of producing that coal. No single system will satisfy the requirement of all mines. Some may require simple hard-wired status-reporting systems; others, multipurpose computer-based systems that collect, analyze, and store data and perhaps control some mine functions. Even though systems vary in complexity, they are all composed of three functional components. The first component is sensors that measure the environmental or production parameters and produce an electrical signal that is fed into the telemetry. The second is telemetry devices that receive the signal from the sensors and transmit it in either analog or digital format to the third com¬ponent, analysis and display equipment. This equipment receives the transmitted signal and either stores it for later analysis or displays it. The analysis-display equipment ranges from simple strip chart recorders with preset alarms to computers, cathode-ray tubes (CRT's), and line printers that can also provide production reports. 4.2 Uses of a Mine Monitoring System A list of potential uses for mine monitoring systems, including both production-related functions and those related to health and safety, was used to develop a questionnaire. It was presented to representatives of the mining community to determine their current monitoring priorities. The responses indicated that the industry's priorities fall into the following two categories: First priority- Production and haulage Maintenance Second priority- Ventilation Communication Fire monitoring Personnel The survey shows that production-oriented systems were the most appealing to the questionnaire respondents. Since even small improvements in production efficiency and maintenance can have a large financial impact, the desirability of monitoring systems that focus on these areas is understandable. The results are summarized in table 4-1. The function that scored 100 was viewed as the most beneficial monitoring function.

Jan 1, 1984

By Ralph V. Higgins

The present methods of appraising the long-range performance of oil reservoirs are based upon physical properties of the crude oil and the permeability of the reservoir rock. By means of these methods the performance of a reservoir may be estimated throughout its entire life. Before these methods were used, the future performance was estimated mostly by extrapolating pressure-decline curves -a method that is satisfactory for extrapolating only for a short period into the future. One factor that affects satisfactory long-range prediction of reservoir performance is the extent to which small changes in the physical properties of the oil and differences in the choices of relative permeability influence the calculated oil recovery. Selection of the physical properties of the samples to represent those of the oil and rock for the entire reservoir is difficult. This report is concerned with the error in calculated recoveries that may result from these inherent difficulties.

Jan 1, 1956

By M. A. Mahtab

This report presents a new procedure for analyzing the orientations of rock fractures in an engineering site. This procedure, coded in a computer program, identifies clusters or groupings among the fracture orientations and calculates (1) the mean orientation of the fractures within each cluster and (2) the dispersion or scatter among these fracture orientations. Data points are represented by intersections of joint normals with the upper hemisphere, which is divided into 100 equal-area quadrilateral patches. The points in adjacent patches where the Poisson distribution test shows significant concentrations are assigned to a single cluster. For a cluster whose fracture orientations follow Arnold's hemispherical normal distribution, a confidence interval for the fracture orientation mean is calculated by applying Fisher's estimates. The technique is applied to the treatment of three examples.

Jan 1, 1972