Search Documents

By Leo J. Neill, O&apos

Abrasives are essential to the manufacture of munitions - airplanes, gas, shells, tanks, and in fact every product that involves metal forming or finishing. An indication of the importance of abrasives in the national defense and aid-to-Britain programs is the close peace-time correlation between demand for abrasives and automobile production, which in recent years has consumed more than 35 percent of the total output of abrasives. Unprecedented demands on the abrasives industry are forecast by the rapid expansion in airplane output, tie increased mechanization of all armed forces, and the consequent speeding up not only of the factories where finished munitions are made but also of the steel mills and other factories were additional large quantities of abrasives are needed for snagging or rough-grinding semifinished products before they can be used by the fabricators. A recent survey by the artificial abrasives manufacturers indicates that they can readily increase their output 75 percent compared with the previous peak of 1937 without building new plants. By overhauling production schedules, their maximum production possible could be increased to 182 percent of the 1937 output, and the nature of the industry is such that plant capacity could be increased rapidly if need therefor should arise. No figures on the estimated requirements for abrasives in 1941 or 1942 have as yet been compiled, but the industry feels that it can meet demands as they develop.

Jan 1, 1941

By E. A. Sondreal

The Bureau of Mines investigated the use of lignite char for producing carbon disulfide; CS2 production rates were as high as when wood charcoal was used as raw material. The maximum space velocity for CS2 produced in the bench-scale study was 9,280 hour-1, reacting sulfur and lignite char at 792° C. The reaction temperature and the temperature at which the char was carbonized were the two most important factors in determining CS2 production rates. Increasing the carbonization temperature in nitrogen from 400° to 900° C advanced the temperature at which carbon disulfide was first produced from 550° to 850° C. The average activation energy for reacting chars with sulfur was 44,000 cal/g mole. The reaction was first order with respect to the partial pressure of sulfur. Increasing the rate of sulfur admission caused a decrease in rate of production at otherwise similar conditions. Rates were not affected by either char size or sodium carbonate catalysis. High space velocities at moderate temperatures using inexpensive lignite chars could offer an economic advantage in the manufacture of carbon disulfide provided that yields were attractive.

Jan 1, 1967

By Charles Prasky

This report describes fluidized bed techniques employed by the Bureau of Mines at Minneapolis to differentially sulfatize the manganese in two samples of low-grade manganiferous ferruginous carbonate slates from the Cuyuna Range district, Minn. Suitable mechanics of operation were established. A space rate of 1.25 to 1.5 fps, a retention time of 3 to 3.5 hours, a temperature of 700° C, and a 10 percent sulfur dioxide gas in air were adequate for sulfatizing the slates by fluidization. Under these conditions the overflow product removal rate from the 4-inch-diameter reactor was 4 to 5 pounds per hour. The sulfur dioxide was used more efficiently in the two-stage treatment than in the single-stage treatment. However, approximately 80 percent of the manganese was converted to sulfate by either treatment.

Jan 1, 1963

Vanadium, molybdenum, and a titanium-10 percent vanadium alloy were evaluated for their susceptibility to stress corrosion cracking in a number of corrodents. Tests were conducted utilizing conventional U-bend techniques with subsequent evaluation in a pneumatic constant-load apparatus. Vanadium and molybdenum were generally resistant to stress corrosion cracking in the media studied. U-bend specimens of vanadium showed evidence of stress corrosion cracking in 6 li hydrochloric and 18 li sulfuric acids; however, tensile stress specimens exposed to these solutions did not exhibit stress cracking. Similar results were obtained when U-bend specimens of molybdenum were immersed in 10 percent formic acid. Titanium-10 percent vanadium alloy was susceptible to stress corrosion cracking in 10-percent (2.85 li) hydrochloric acid solution. Heat treating the alloy greatly reduced its corrosion rate and its susceptibility to stress cor-rosion cracking in this medium.

Jan 1, 1965

By Federick W. Miller

The Bureau of Mines has investigated the availability of columbium from 19 deposits (3 producers and 16 nonproducers) in 7 market economy countries (MEC?s). Brazil has the largest recoverable columbium resource, posessing approximately 2.39 million metric tons Wmt), or 69 pet of the MEC total (3.47 Mmt). The Western Hemisphere countries of Brazil, Canada and the United States contain 3.14 Mrnt of recoverable columbium or 90 pnt of the MEC total. Columbium recovered as a byproduct of tin mining is not included as part of MEC resources in this study. Currently producing mines are Araxa and Catalao in Brazil, and Niobec in Canada, These three mines have 2.42 Mmt of recoverable resources or approximately 69 pct of the MEC total. It is estimated that these mines, operating at full capacity, could satisfy cumulative MEC demand (based on an annual growth rate of 5.1 pct) for the next 20 yr. The United States is totally dependent upon foreign sources for its columbium supply. The majority of U.S. columbium is imported from Brazil in the form of steelmaking- grade ferrocolumbium. Canada has been the sole source of pyrochlore concentrates since Brazil discontinued exports in 1981. The United States also imports small (but important) quantities of columbium as columbite concentrates from Nigeria and Brazil, as columbite contained in tin slags from Thailand and Malaysia, and as synthetic concentrates from the Federal Republic of Germany.

Jan 1, 1986

By K. E. Soroka

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,0000 C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first held field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fifth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 1, 3, 4, and 5.) Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and this part (part 5) describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water-injection-fume exhaustion quenching procedure are planned.

Jan 1, 1986

By Stephen C. Tadolini

The U.S. Bureau of Mines conducted a laboratory investigation designed to evaluate the stress and deformation characteristics of fully grouted roof bolts subjected to various magnitudes of end loadings. The experiment and subsequent analysis were completed, utilizing axial deformation data obtained -ultrasonically from forty-one 4-ft, grade 40 roof bolts, with a total of 132 measurement locations along the lengths of the bolts. The ultrasonic measurement instrumentation used in this investigation allowed for elongation measurements without requiring extensive bolt modifications. The results indicate that approximately 39 pct o{ the applied end load dissipated within the first 3.4 in of the bolts. However, only 3 pct of the applied load was realized beyond 28 in of the grout column. Data are presented individually for every 6-in increment of bolt length, and analysis was performed using statistical, nonlinear equations developed for 5,000 and 8,000 lb loading conditions.

Jan 1, 1990

By J. M. Singer

Thermal, mechanical, and physical properties of virgin and heat-treated Pittsburgh seam coal were determined as part of a comprehensive study of combustion of monolithic coal block. The information was sought to help characterize pyrolysis and combustion processes in underground coal mine fires but should also prove useful in the study of in situ and surface coal gasifiers. Measured properties include thermal conductivity, specific heat, thermal expansion, density, compressive and tensile strength, porosity, and permeability. The transport property data were obtained (when feasible) in two mutually perpendicular directions of the anisotropic virgin coal material, and coal samples carbonized for 5 hours at temperatures of 350° C, 475° C, 500° C, 650° C, and 850° C. Other coals (Pocahontas No. 3, Sewell, and Illinois No. 6 seams) were investigated for porosity and relative permeability. Interdependence among all properties was evident from the results; however, only a few correlations could be developed owing to inhomogeneity of coal material and specimen variation, which had the effect of reducing the accuracy of measurement and increasing data scatter.

Jan 1, 1979

By S. P. Sandoval

The U.S. Bureau of Mines investigated the separation of aluminum from copper dump leaching liquors using a supported liquid membrane. Aluminum was selectively transported through porous polypropylene impregnated with di (2-ethylhexyl) phosphoric acid in an aliphatic diluent. The effects of variables, such as solution composition, temperature, and extractant concentration, were measured with a three-level fractional factorial experimental design. Experimental results were used to derive equations for predicting transport rates for aluminum, iron, and copper. The major variables influencing aluminum transport were solution temperature, feed solution pH, aluminum concentration in the feed solution, and extractant concentration. Copper and iron transport rates were almost zero when aluminum transport rates were high. Measured aluminum transport rates under the best conditions of 55° C, pH 3.0, 16 g/L A13+, and 65 pct extractant solution confIrmed the predicted value of 210 f.'g/(cm2.h). Transport rates for iron and copper were less than 5 ug/(cm2.h) under these conditions. Aluminum was recovered from the stripping solutions by sparging with gaseous hydrogen chloride to crystallize aluminum chloride hexahydrate, which was calcined to alumina. Sparging crystallization regenerated the stripping acid for recycle.

Jan 1, 1989

By Laxman S. Sundae

Laboratory tests were conducted at the U.S. Bureau of Mines to determine the effects of roof-bolt drilling parameters on penetration rate in sandstone using tungsten carbide alloy (WC-Co) and polycrystalline diamond compact (PDC) drill bits. During the tests, water pressure of 552 kPa was found to be adequate for removing the cuttings from the tops of drill holes. Test results show that for both types of bits, penetration rate increased when thrust was raised from 227 to 1,588 kg. When water pressure rose from 554± 120 to 1,344±350 kPa, the effect on penetration rate was not significantly different. Conventional WC-Co bits became dull when one or two holes were drilled, after which the penetration rate dropped dramatically. Microscopic examination shows that the cutting edges of PDC bits also become somewhat dull, but at a much lesser rate than WC-Co tips. Microscopic examination also reveals that the wear mechanism of WC-Co and PDC bits is quite different, which may explain the longer life of the PDC bits.

Jan 1, 2010

By Oliver C. Ralston

The nonmetallic minerals work of the Bureau of Mines started with the organization of the Mineral Technology Division in 1912. A special experiment station devoted to the mining, preparation, and processing of nonmetallic minerals was established in 1923 at New Brunswick, N. J., and concentration problems on nonmetallic minerals of all kinds also were studied at the Mississippi Valley Experiment Station at Rolla, Mo. In July 1936 the Nonmetals Division was organized, and in May 1937 the Nonmetallic Minerals Experiment Station at New Brunswick, N. J., was moved to and made a part of the new Eastern Experiment Station at College Park, Md. At present the Nonmetals Division operates at three points: The Eastern Experiment Station, College Park, Md., which is headquarters for the division chief; the Southern Experiment Station, Tuscaloosa, Ala.; and the Northwest Experiment Station, Seattle, Wash., where coal washing and preparation studies are included with those on nonmetallic minerals. Sand, gravel, and aggregate work is carried on by the Mining Division, as sand and gravel preparation are intimately associated with mining methods. The Economics Branch of the Bureau of Mines also prepares occasional papers on nonmetallic technologic subjects in connection with the presentation of statistics on a particular industry and reviews of the mineral industry in foreign countries for use in the monthly publication, "Mineral Trade Notes."

Jan 1, 1937

By H. M. Smith

Data from the Bureau of Mines routine method for the analysis of crude petroleum are used to characterize crude oils. Some data are used directly while other data are used to calculate the aromatic) naphthene) and paraffin contents of the distillation fractions and the correlation index of the paraffin-naphthene portion of the fractions. The calculated properties show significant differences in composition between crude oils. The methods of calculation and interpretation of data are explained and illustrated.

Jan 1, 1966

By William H. King

The property of the Cupric Mines Co. is situated in the San Francisco mining district, Beaver County, Utah, 21 miles westerly from Milford (fig. 1), the rail and supply center for the area. Scheelite mineralization was not discovered until 1941, although the occurrence of lead and copper minerals had been known previously. S. VI. Hobbs, of the Federal Geological Survey, examined the Cupric property in November 1941 and prepared topographic and geologic maps of the area. This work was supplemented by additional investigations in January 1943 and March 1944 (fig. 2).

Jan 1, 1949

By W. J. McKenna

This paper, describing the milling practice at tine lead-zinc concentrator of the International Smelting Co., is one of a series of papers on milling methods being prepared by the United States Bureau of nines. The concentrator is operated as a unit of the International Smelting Co. and is located about 40 miles southwest of Salt Lake City, at Tooele, Utah. The Tooele Valley Railroad, operating between the plant and Warner, Utah, a distance of 6.5 miles, makes connection with both the Union Pacific and Denver & Rio Grande Railroads.

Jan 1, 1933

By E. M. Tignor

A research program to aid development of improved methods for increased production of petroleum from partly depleted reservoirs is a vital part of the Bureau of Mines effort to effect true conservation of that mineral resource. This report presents results of an investigation to identify the clay minerals within some Appalachian petroleum-reservoir sands, the effect of clay content on the fluid-flow behavior of those sands, and the use of brines in water-flooding operations. Permeability measurements using kerosine, calcium chloride brine, simulated oilfield brine, potassium chloride brine, sodium chloride brine, and distilled water were made on reservoir-rock cores. Clay fractions were separated from sand grains of disaggregated portions of each core sample, and the clay minerals were identified by the differential thermal analysis method. Relations of the permeability to various fluids were developed.

Jan 1, 1957

By G. Richards Gwinn

"Mica" is a group name for a number of orthosilicates of aluminum with magnesium, ferrous iron, and the alkalies. They are characterized by their high reflection and a basal cleavage so well developed that they can be split into exceedingly thin laminae, which are more or less tough, elastic, and transparent, according to variety. Barium, manganese, lithium, chromium, titanium, boron, and ferric iron occur in same varieties. Eight distinct species of true mica, which appear in the following table, are recognized by mineralogists, but only the first five are of commercial importance. [Species General Formula Muscovite H2KA13 (SiO4)3 Phlogopite [H,K, (MgF)]) Mg3A1 (Si04)3 Biotite (H,K)2(Mg,Fe)2(Al)Fe)2 (S104)3 Lepidolite K,Li Al(OH,F)2 Al (5103)3 Ros coalite H8K(Mg,Fe) (A1,V)4 (S103)12 Paragonite H2NaAl3(S104)3 Zinnwaldite (K)Li)3 FeAl3 Si5016(OH,F)2 Lepidomelene HK2F3IIIFe6III A13 (S104)9]

Jan 1, 1951

By Charles L. Kimbell

In overview, 1988 appeared to be the best year for the world's mineral industry since 1980, although the all-important petroleum component suffered severely from low prices. With this notable exception, the traditional statistical measures of mineral industry performance, namely production, trade, and consumption, reflected growth in most elements of the world mineral industry from crude material extraction through the gamut of downstream processing. Moreover, the growth was reasonably well distributed geographically, with many countries sharing in the substantial upturn in activity. World crude mineral output value was estimated at over $1,272 billion in current dollars ($1,090 billion in constant 1983 dollars). The value added by the processing component of the mineral industry raised the total value of the industry's output to an estimated $3,057 billion in current dollars ($2,620 billion in constant 1983 dollars). Less easily assessed was the value of mineral commodities moving in 1988's international world trade, particularly because of the declines in world crude oil and refinery product prices. It remained to be seen if increased volume and value in nonfuel mineral and coal exports, coupled with an increase in the volume of oil exports, would be adequate to offset the drop in oil prices. Whether or not the value of world mineral commodity trade topped the 1987 level of over $498 billion, an increase in the volume of mineral commodity trade was almost assured. Similarly, although comprehensive statistics were not avail-able on consumption of all mineral commodities in all countries, available data on selected major commodities in selected major countries suggested that not only had output of most mineral commodities advanced, but so too had consumption levels for most commodities.

Jan 1, 1990

By Dorothy M. Richardson

The Bureau of Mines has participated in the American Petroleum Institute Research Project 48A (API-RP48A) program on the Separation and Identification of Sulfur Compounds in Crude Petroleum. The lack of reference compounds or infrared spectral data has made difficult the identification of individual sulfur compounds boiling above 140° C. The recent acquisition of 24 alkylthiophnnes has made possible a limited study of this important class of sulfur compounds. The infrared spectra of 2-monoalkylthiophenes and 2,5-dialkylthiophenes for the 2 to 15p range are reported. Correlations for determining the 2-alkyl and 2,5-dialkyl substituted thiophenes are derived from this information. The 2-alkylthiophenes show a unique pattern in the 5.50 to 6.54 region, while the 2,5-dialkylthiophenes show a distinctive pattern in the 5.6µ to 6.7µ region. A skeletal vibration occurs in the 9.5 to 10.0µ region for all of the thiophenes investigated. These data will aid the infrared spectroscopist in the identification of compounds of the type reported.

Jan 1, 1961

By R. V. Subramanian

This project financed by the Bureau of Mines investigated the use of polymers to achieve rock bonding and reinforce coal mine structures for better or permanent ground support. Support was achieved by pumping the polymers into the rock interstices to bond the mass together for increased structural competence. Holes were drilled in the mine roof, after which the polymers were injected at about 100 psi to permeate the cracks. Initial laboratory work indicated that of all the resin systems tested, the epoxy resins could most likely be modified to be suitable for rock injection. This was confirmed when several potentially suitable resin systems underwent intensive evaluation. In a series of three field tests, two conducted in a copper mine with coal mine-type shale and the third in a coal mine, it was shown that the polymers penetrated cracks less than 0.005 inch wide. The fast-setting epoxy systems, cured out in thin films under mine conditions, produced a bond exceeding the strength of the uncracked virgin rock.

Jan 1, 1974

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974