Search Documents

By S. H. Ash

THIS REPORT covers the third in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the work constituting Project No.3 that consists principally of the following: (a) To sink the No. 15 shaft and extend the Alden, Sugar Notch, Baltimore No.2, and Laflin shafts from their present depths to tunnel level; (b) to drive a tunnel off these shafts to connect with the western end of the tunnel in Project No.1 (Lackawanna) and to a point 1 mile south of the No. 15 shaft; (c) to construct an emergency pumping plant at the No. 15 shaft, complete with 3 centrifugal pumps of 200-cubic-foot-per-second (c. f. s.) capacity each, and a discharge-water shaft and a discharge tunnel for conducting the water from the pumping plant into the Susquehanna River; and (d) to construct a lateral tunnel 1 mile long off the main tunnel in the vicinity of the No. 15 shaft, to be known as the Wyoming lateral. The project, as outlined, is a self-contained drainage unit that will permit unwatering inundated mines and safeguarding active mines in the Wyoming Basin of the Northern field and also will handle the water in the Lackawanna Basin, thus permitting the temporary pumping plant provided in Project No.1 to be discontinued. The pumps installed in the temporary pumping plant provided in Project No.1 can then be moved to the emergency pumping plants recommended in Projects Nos. 2 and 3, to be installed as the third or standby unit.

Jan 1, 1955

By Lyman Moore

This Bureau of Mines report describes 2nd evaluates iron ore resources in California and Nevada and analyzes the California and Japanese iron ore markets in which these resources will be used. The competitive position of California-Nevada ores, in these markets, was estimated by comparing regional iron ore prices, production costs, and transportation costs with those of foreign suppliers. Resources were determined to be sufficient to produce the equivalent of 585 million tons of 64-percent iron pellets at a price of less than $15 per ton delivered at California ports. Much higher tonnage could be produced at higher prices. Iron ore requirement of the California iron and steel industry will increase to an estimated 15.9 million tons by the year 2000. A study of the iron ore production potential of California-Nevada deposits and of out-of- State sources indicated that this ore requirement can be supplied most economically by California-Nevada ores. Iron ore import requirements of the Japanese iron and steel industry will increase to an estimated 150.0 million tons by the year 2000. A study of price trends in this market indicated that very little California-Nevada iron ore will be sold in Japan after 1973 when existing sales contracts expire. Iron ore-exports might be economically possible if ore could be transported from California to Japan at ballast rates as backhaul on existing petroleum shipping.

Jan 1, 1971

By W. W. Agey

An inexpensive technique that laboratory studies indicated would significantly reduce seepage in irrigation canals was devised and tested through research sponsored by the Bureau of Reclamation and the Missouri River Basin Field Committee. Laboratory tests simulating optimum field conditions determined that easily applied sodium carbonate solutions made test beds of canal lining materials virtually impermeable for long periods. The study comprised alternative laboratory treatments of 3-inch-deep test beds of canal earths with 74 water-soluble chemicals in search of one 01' more that would effectively improve the water barrier characteristics of the component clays. Sodium carbonate, one of the least expensive, was among the most effective. The addition of 0,4 lb of reagent per sq yd greatly reduced the seepage from typical, highly permeable test beds. The reagent penetrated and sealed surface for about a 1.5-inch depth.

Jan 1, 1965

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By D. E. Shanks

The Bureau of Mines surveyed a variety of inorganic ion-exchange materials to determine their suitability for removing valuable accessory elements and troublesome contaminants from metallurgical process and waste streams. Most of the materials, which included molecular sieves, heteropolyacid salts, and hydrous metal oxides, did not give adequate separations, did not have the necessary stability in strong acids or bases, or were not in a physical form suitable for ion-exchange use. Many of the suitable inorganic materials, especially the hydrous oxides, were capable of cation exchange with high capacity only in basic conditions, which caused hydrolysis of most of the cations tested. Multivalent anions, such as arsenate and phosphate, were easily removed from acidic solutions by hydrous oxides. Hydrous zirconia was the best material for this purpose. Multivalent anions were not easily des orbed because of compound formation; therefore, conventional ion-exchange techniques could not be employed. As an alternative approach, hydrous ferric hydroxide was used as a filter material to remove arsenate and phosphate from acid solutions. One gram of arsenic was removed from solution for each 20 g of ferric hydroxide. Ferric hydroxide is preferable to hydrous zirconia for use as a filter material because of low cost.

Jan 1, 1983

By Chas. F. Jackson

This circular is an abstract of a manuscript-completed in August 1932, which cannot be published in its entirety due to lack of printing funds. It was originally planned to publish the manuscript as one of a series of bulletins dealing with the mining and milling of ores of the principal metals. Because of the common association of lead and zinc minerals in many ore deposits, and because a considerable proportion of the zinc produced in this country is obtained as a by-product of lead mining or vice versa, it seemed necessary to treat the mining and milling of lead and zinc ores in the same volume.

Jan 1, 1934

By R. L. Brown

This report, summarizing the Bureau of Mines research and technologic work on coal and coal products for the period July 1, 1950, to July 1, 1951, is based largely on publications issued during the year. The sixteenth in an annual series, it gives footnote references to publications giving further details of the research and technologic work described, except in a few cases where research data presented herein has not been published previously. During the year, the national fuels situation was generally one of plentiful supply.3/ Mineral-fuel resources appeared adequate for several hundred years at reasonably increasing rates of supply. Coal-production capacity was in excess of demand; petroleum supplies were adequate; and natural gas use was limited only by pipeline capacity. However, it was pointed out that a world war would drastically change this situation of relative plenty, particularly with regard to supplies of petroleum and its products. Conversion to the use of coal on a large scale would be required, and improved methods of mining and of processing and using coal in solid or fluidized form or converted to liquid fuels could materially contribute to our national safety.

Jan 1, 1952

By Will H. Coghill

This paper on milling methods and costs at a flat river (Mo.), mill is one of a series of information circulars on milling methods and costs which is being prepared by the United States Bureau of Mines, The mill under consideration treats 5,000 tons of load ore daily by table concentration and flotation. It is 25 years old, and yet it is a new mill. Research has been in continual progress at the plant since its beginning, and accordingly a day never passes without a record of change for advancement. The changes have been so orderly that no evidence of obsolete equipment remains.

Jan 1, 1932

By Kenneth M. Maas

The Bureau of Mines inventoried the land in southwestern Alaska to classify ownership and availability and compared this land with known mineral terranes and mineral deposits. This report discusses and quantifies the potential for favorable location of mining claims for metalliferous (locatable) mineral deposits. Of the nearly 24 million acres that constitute the study area, approximately 3.6 million acres or 17% are available for mineral location, 3.4 million acres or 14% are available with restrictions, and 17 million acres or 71% are unavailable. Mineral terranes are known to underlie about 7.8 million acres or 33% of the study area; 3 million acres or 38% occur on land available for mineral location, 1.3 million acres or 17% occur on land available with restrictions, and 3.5 million acres or 45% occur on unavailable land. The State of Alaska has opened over 91 % of its land in the study area to mineral location; in comparison, the Federal Government allows mineral location on 0.07% of the land under its jurisdiction. There are 117 known mineral deposits or occurrences within the study area, including 77 lode deposits and 40 placer deposits. Of the 41 lode deposits occurring within a mineral terrane, 2 occur on available land.

Jan 1, 1988

By J. M. Provost

1. Estimates have been made for eight coal beds in Marion County, but only the Pittsburgh is important from a production standpoint at this time. The Pittsburgh bed has the largest recoverable reserve, and the Sewickley is second in importance. 2. Known measured and indicated reserves thickness of 14 inches and on 1,800 short tons estimated at 3,141 million tons, as of January lion tons is in beds 28 inches and more thick in all beds, based on a minimum per acre-foot of coal in place, are 1, 1955. Of this total, 2,983 mil-Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By S. H. Ash

THE information obtained by examining and analyzing the core drillings from 15 diamond-drill holes shows that with the proper equipment little difficulty should be experienced while sinking the shafts at the 15 selected sites. Although a number of holes penetrated formations containing a high percentage of silica,, the health hazard from dust can be removed by using proper dust-control equipment. Methane was detected in small amounts in only one (hole 5) of the boreholes. The methane hazard should present no difficulty if adequate ventilation is employed while sinking the shafts.

Jan 1, 1952

By Seth T. Reese

THE INJURY and related employment experience of the coking industry in the United States for 1953 contained in this bulletin are presented under three general sections, as follows: (A) General injury experience: Tables 1 to 9: Contain current and comparable statistics on operating data, number, frequency, and severity of injuries, and major accident agencies involved in the cause of injuries. Data are tabulated for the industry as a whole, for each type of oven, and for the States in which coke is manufactured. (B) Selected injury experience: Tables 10 to 15: Contain comparable injury data covering 5- and 10-year periods on the number and severity of injuries and major accident agencies. (C) Historic injury experience: Tables 1.6 to 19: Contain data on the number and rates of injury occurrence and related employment statistics on the industry from the earliest records through 1953.

Jan 1, 1955

By K. R. Van Doren

The polynomial method for estimating virial coefficients from experimental data suffers from three serious defects: (1) There is no known relationship between the polynomial coefficients and the virial coefficients, (2) the values of the estimates depend upon the degree of the polynomial and the particular set of values used for the independent variable, as well as the random errors in the dependent variable, and (3) the variances calculated for the estimates do not represent the mean square errors of estimation. Attempts to overcome these defects have thus far been unsuccessful; these attempts have also failed to account for the fact that none of the virial coefficients are uniquely determined by the values of the dependent variable for a finite set of values of the independent variable. The conclusion is that virial coefficients cannot be reliably estimated from experimental data unless additional information about the virial expansion itself, such as its rate of convergence, is available.

Jan 1, 1969

By J. A. Organiscak

Quartz dust is one of the most significant ongoing health concerns in coal mining today. Since the early 1980's, the U.S. Bureau of Mines has conducted numerous studies in underground and surface coal mines to identify the sources of quartz dust and its fundamental characteristics. This report presents data and conclusions obtained from these studies. The two most significant quartz dust sources were found to be the continuous miner excavating rock and the highwall drill operating in a rock overburden. The percentage of quartz was found to be higher in the smaller size fractions of dust when significant amounts of rock were mined by the continuous miner. Another factor theorized to affect quartz dust generation and size characteristics is the morphology of the quartz-bearing rock. Several laboratory studies were conducted to investigate capture efficiency of water spray technology and flooded-bed scrubbers with respect to the particle size of the dust. Water sprays and flooded-bed scrubbers were both found to be less efficient on smaller dust particles, and the scrubber was particularly less efficient on quartz dust. These results indicate that quartz control technology should be directed at controlling smaller sized dust particles.

Jan 1, 1990

By Joseph A. Hrabik

The Bureau of Mines compared the feasibility of mining deep phosphate deposits by a borehole mining system with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 150 ft or greater; however, at 50- and 100-ft thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasiblity of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is employed to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1983

By J. W. Thompson

A contract stipUlating for the delivery of quantities of phosphate rock" f. o. b. mines," and stipUlating that" while this contract is in form an absolute sale for a fixed quantity in each year, it is mutually understood and agreed that the purchase is for the buyer's consumption and not for a sale; the buyer agreeing to give to seller the refusal of any surplus over and above the actual consumption. Buyer is at liberty to increase or diminish the quantity called for in any year, to the extent of not exceeding 10 per cent; provided that the quantity to be taken shall not be less than buyer's consumption; provided further that notice of such increased or diminished demand be given seller 12 months in advance of such change," is to be construed as a contract for the sale of stated quantities of rock, deliverable in approximately equal quantities during each year for the specified series of years, subject only to be increased or diminished after specified notice in any year, where the amount taken would not be les<; than the buyer's consumption, not exceeding 10 per cent, and the contract indicating that the rock was intended by both parties for consumption in the fertilizer plant of the buyer. but the quantity to be taken was not limited by the necessities of' the plant.

Jan 1, 1916

By A. Aly Selim

This report describes the feasibility of predicting percussive drilling rates by equations derived from statistical regression analysis. The least squares statistical method was used and the analysis was performed both by direct and by stepwise linear regression analysis. The predicted penetration rate is a function of the drill power and the physical properties of the rocks penetrated. The results show promise that the technique may be of value in providing a mathematical model by which percussive drill manufacturers and users can predict the performance of a given drill. Experimental work involved two mining type percussive drills. Penetration data for these drills were determined from nine rocks drilled in the laboratory. Drill work rates (power) were determined in a separate series of experiments. Rock physical properties were measured from diamond-drill core samples taken from the same blocks used for percussive drilling.

Jan 1, 1970

By Lewis C. Karrick, Martin J. Gavin

"Introduction.The theory of fractional ""education"" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil from the oil shales of the United States. The term fractional ""education"" gives expression to the rather common belief that when an oil shales is heated it produces light, low-boiling oils as low temperatures, and increasingly heavier, higher-boiling oils as the temperature of retort¬ing rises. The theory evidently had its origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases is as, gasoline is produced from petroleum at relatively low temperatures, kerosene at higher temperature, and heavier products such as gas-oil and lubricating distillation at still higher temperatures.The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and in some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperat.res, and so on. Such retorts are usually designed to operate continuously and have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts repeat that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale passes to zones of increasingly higher temperatures, the vapor lines lending from these zones rill remove increasingly heavier products such as kerosene, gas-oil etc."

Mar 1, 1924

By E. T. Bowers

The Accident Analysis (ADA) computer program was developed at the Spokane Research Center (SRC) to provide a rapid broad-based analysis of mining accidents. Because the Bureau of Mines often needs this type of information for the development of viable research programs the ADA program was written to access and analyze accident data available frog the Labor Department&apos;s Mine Safety and Health Administration (MSHA). This report describes the ADA program, the data it uses, and the potential value it has for planning mining research.

Jan 1, 1987

By W. W. Adams

With production of coal per man-hour of work highest in history, the coal mines of the United States established a lower accident-frequency4 rate in 1942 than in any year since 1930, the first for which the Bureau of Mines, United States Department of the Interior, collected complete reports of nonfatal as well as fatal injuries. Reports from mine operators and State mining departments showed that 530,861 men were employed in and about coal mines during the calendar year 1942. This number does not include office employees or coke-oven workers. The figure represents a decrease of 15,831 men from the previous year, owing to losses of men to the military services and to more lucrative employment in the munitions and other industries. The loss of men was offset to some degree by an increase in the number of days of mine activity and the average number of hours of work per man during the year. The volume of work done during 1942 was 910 million man-hours, 11 percent more than in 1941. The average employee worked 243 days, 30 days more than in 1941. Production reached the unprecedented total of 640 million short tons, an increase of 12 percent over 1941; 582 million tons came from the bituminous fields of the United States and 58 million tons from the anthracite fields of Pennsylvania. To produce this quantity of coal 1,471 men sacrified their lives, and 69,564 men suffered nonfatal injuries that disabled them for more than the remainder of the day on which the accident occurred. The nonfatal injuries were divided into three groups: 65 caused permanent total disability, 2,045 caused permanent partial disability, and 67,454 caused temporary disability of 1 day or more but did not result in the loss of, or permanent loss of use of, any part of the body.

Jan 1, 1944