Search Documents

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

By A. C. Fieldner

"Decline of the Beehive Coke OvenTwenty years ago a favorite theme of the crusader for fuel conservation was the enormous waste of valuable by-products incurred in the manufacture of blast-furnace coke in beehive ovens. Indeed, there was good reason for arousing the national conscience to this needless' loss of an irreplaceable mineral resource. In 1910, 83 per cent of the coke production was made in beehive ovens, from which surplus gas, tar, light oil, and ammonia, aggregating in value (at 1910 prices) 40 million dollars annually, were discharged into the atmosphere.In 1929, proportions were reversed and 90 per cent of the production was made in by-product ovens. The average value of by-products obtained in the production of 1 ton of coke in 1929 was $3.60, as compared with $1.16 in 1910, although the value of a ton of coke had increased only from $3.47 to $4.80. As shown in Figure 1,1 the production of by-product coke progressed rather slowly until 1915. War needs suddenly expanded the demand for coke and the by-products benzol and toluol for the manufacture of explosives. Except during the depression of 1921, this accelerating rate of production was maintained up to 1929, largely at the expense of beehive plants. The 1929 production of 60 million tons of coke will probably remain a record-breaking figure for several years. The developments which are now in progress in long-distance transmission of rural gas and in the utilization of volatile petroleum products and refinery gases for augmenting, city gas supplies may retard an other- wise accelerating demand for coke and coke-oven gas for domestic and industrial heating, Trends in Value of By-ProductsThe increasing value of by-products in comparison to the value of coke is shown in Figure 2. In 1913, the average value of by-product coke was $3.38, the value of the by-products per ton of coke was $1.41, and the cost of coal per ton of coke was $3,27, In 1929 not shown in figure) the value of the coke had risen to $4.80 per ton, the value of the by-products to $3.60, and the cost of coal per ton of coke to $5.07. The by-product values in were 155 per cent higher than in 1913, although the coke value had increased only 25 per And the cost of the coal 55 per cent. Actually the increase or the total value of coke plus by-products in this period was very little more than the increase in the coat of the coal, being 55per cent for coal and 60 per cent for coke plus by-products."

Mar 1, 1931

By Kray Luxbacher, Mario Karfakis, Erik Westman, Peter Swanson

Three-dimensional velocity tomograms were generated to image the stress redistribution around an underground coal longwall panel to produce a better understanding of the mechanisms that lead to ground failure, especially rockbursts. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Eighteen tomograms were generated and high-velocity regions correlated with high abutment stresses predicted by numerical modeling. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated, indicating that velocity tomography may be an appropriate technology for monitoring stress redistribution in underground mines.

By C. M. McKinney

The Bureau of Mines analyzed 626 crude oils from 546 oilfields in the United States that produced 2,500 BOPD or more during at least 1 of the last 3 years. Included also are crude oil analyses from eight fields that produced less but which were located in areas having few or no fields that produced 2,500 BOPD. The tables show the geographical and geological source, general characteristics. and determined and computed analytical data for each sample. The analyses were made according to the Bureau of Mines routine method and are directly comparable to other previously published analyses.

Jan 1, 1966

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage bf measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1983

By Thomas Varley

During the past few years, since flotation has become the paramount treatment method for most all kinds of ores, the Bureau has gathered the data on consumption of reagents used in the flotation treatment. The first report was issued in 1916. A brief review of such reports snows the progress made in the art of flotation, and each year brings forth the development of new reagent a or combinations of reagents that seem sure to survive, but research and progress spell their defeat, if not by entire elimination, at least subjects them to considerable modification.

Jan 1, 1928

By George L. Gates

[When clays e.re mixe~ "Jith "~later to nake mud fluids f'ol' use in :irilling ','Iells "for oil and gar: h;:r vue :;'0 tary me thee. t 18 liquid mij~ tUl"es have certair.. phypicr..l characteri.",t.ics that vary ",dth t e Qlldlltit.y find]

Jan 1, 1941

By John F. Papp

International and U.S. chromium material flow, losses, and environmental releases and transfers from mining through industrial processing, end use, and recycling are identified and quantified. Average (1983-92) U.S. consumption has been: metallurgical industry, 87 pct; chemical industry, 10 pet; and refractory industry, 3 pct. Average chromium content of aluminum, cobalt, copper, nickel, and titanium alloys and alloy, carbon, and stainless steel alloys was estimated. Anthropogenic chromium consumption was estimated for the cement and copper industries. N on-commodity cycle anthropogenic chromium mobilization resulting from U.S. fuel and fertilizer use was estimated. Commodity cycle anthropogenic world chromium loss from mining and primary consumer industry was estimated to be equivalent to about 56 pct of chromium contained in chromite ore production and represented a loss rate of 181 kt-Cr/Mt-CrOre. Chromium released to the atmosphere from natural and from anthropogenic sources were comparable in magnitude. Chromium released to soil was mostly from anthropogenic sources, and aquatic releases were all anthropogenic. Domestic product chromium losses exceed process losses by more than a factor of 10 showing the importance and potential environmental impact of post-consumer recycling. The location of historical and current domestic chromium industry processing sites in 23 States were reported. Chromium releases and transfers to the environment were estimated from 1973 through 2002 by primary consumer industry. A decrease in chromium releases and transfers to the environment was anticipated.

Jan 1, 1995

By W. F. RITTMAN, E. W. Dean

This report presents the results of an investigation conducted by the Bureau of Mines for the purpose of assisting in the establishment of a satisfactory standard method for the analytical distillation of petroleum, a problem of great importance to the petroleum industry. Experiments were performed for the purpose of studying the charac- teristics of methods typical of those in use; comparative studies were made of the efficiencies of the principal types of fractionation ap- paratus available to the petroleum chemist; and the characteristics of a type of apparatus that the results of the experiments seemed to indicate was best adapted to the purpose were investigated in detail. Also, some experiments were made to determine the effect of cracking as a factor in the analytical distillation of petroleum in still heads.

Jan 1, 1916

By J. H. East, D. Harrington

"INTRODUCTION Shaft mines, coal and noncoal alike, have a common hoisting problem that remains largely unsolved - how to obtain a mechanical device that will suspend a cage or skip in a mine shaft if the hoisting rope should break or become detached from the cage or skip and that will function effectively under all conditions of service. Safety catches, or safety dogs, as they are commonly named, are installed on nearly all mine cages and many skips operating in American mines, but often, if the hoisting rope breaks, the cage or skip falls to the bottom of the shaft in spite of safety devices, causing much property damage and often fatalities.Available information relative to safety catches for mine cages and skips, desirable characteristics of safety catches and methods of testing safety catches to determine whether they are functioning correctly has been assembled in this publication for the convenience of those responsible for the safe operation of mine cages end skips and, more particularly, to focus attention on the need for a device that actually will stop and suspend a falling cage or skip under all conditions of use and do it without killing or maiming the occupants."

Feb 1, 1948

By R. J. Matetic, J. S. Peterson, P. G. Kovalchik

The National Institute for Occupational Safety and Health (NIOSH) has initiated a study of a roof bolter to reduce noise exposure to mine roof-bolter operators. An important segment of this research entails determining the affect of various drilling configurations on the performance (penetration rate) and sound power emissions when drilling into granite. Test conditions included using various combinations of rotational speeds and thrusts, using 2.54- and 3.49-mm- (1- and 1 3/8-in.-) diameter hexagonal and round drill steels, using vacuum and wet conditions and using drill media of differing compressive strengths. This paper details the affects of each of these variables on the performance and sound power level emission. When drilling into granite, it was found that wet drilling generated lower sound power levels and performed better than vacuum drilling.

By W. L. Dare

This circular is the first of a series of publications describing uranium mining on the Colorado Plateau. Later circulars are planned in which exploration, development, and mining methods and costs will be described after a detailed study of various operations. Because of the introductory character of this paper, those well-publicized phases of the industry such as geography, history, prospecting, and exploration are described but briefly. Primarily, attention has been devoted to the general problems that are encountered in mining ore bodies and to the factors that affect the selection of development and mining methods. Those familiar with mining may class the information contained in this paper as elementary; however, its inclusion is considered necessary for the completeness of the series of papers. It will also serve as a source of information for people who are interested in uranium but are unfamiliar with mining.

Jan 1, 1955

This report contains the papers presented at the Technology Transfer Seminar on Ground Control Aspects of Coal Mine Design held by the Bureau of Mines on March 6, 1973, in Lexington, Ky. Seminar attendance consisted of representatives from the coal mining industry, universities, mining consultants, instrument manufacturers, and local, State, and Federal Government. The purpose of this meeting, one of a series of Technology Transfer seminars, was to provide the coal mining industry with detailed information about recently developed techniques, equipment, and instruments which can be used in the solution of coal mine design problems and to discuss results and direction of research in mine design. The report includes opening remarks by Joseph J. Yancik, Acting Assistant Director--Mining; an overview of the Federal Bureau of mines approach to mine design; three papers an problems associated with the design of panels; five papers on coal mine roof problems; three papers on long wall problems; and the comments made by- the participants on the Bureau-industry panel discussion.

Jan 1, 1974

Advances were made during 19b5 in many phases of a broad program designed to increase efficiency in the mining, preparation, and utilization of coal. Also recorded were achievements in activities devoted to mine health and safety, coal resources, and mine explosives. Featured in this report is a review of progress in environmental studies relating to coal mining and utilization. Environmental projects comprise a comprehensive program to facilitate mine reclamation and reduce air and water pollution associated with extraction and use of coal. Publications cited throughout this report present results of the coal program in greater detail. Organizations, institutions, and companies contributing to the program are listed in appendix A. Centers and laboratories conducting the coal research and related investigations appear in appendix B.

Jan 1, 1966

Advances were made during 19b5 in many phases of a broad program designed to increase efficiency in the mining, preparation, and utilization of coal. Also recorded were achievements in activities devoted to mine health and safety, coal resources, and mine explosives. Featured in this report is a review of progress in environmental studies relating to coal mining and utilization. Environmental projects comprise a comprehensive program to facilitate mine reclamation and reduce air and water pollution associated with extraction and use of coal. Publications cited throughout this report present results of the coal program in greater detail. Organizations, institutions, and companies contributing to the program are listed in appendix A. Centers and laboratories conducting the coal research and related investigations appear in appendix B.

Jan 1, 1966

Objective The main purpose of this video is to teach mine rescue personnel certain aspects of rescue work that are not traditionally taught. These include the strain caused by working continually under adverse conditions; the "survivor guilt" that occurs from being spared the fate of one's deceased cohorts; and the posttraumatic stress that may be experienced during the sometimes lengthy task of recovering the victims' bodies. Background On November 20, 1968, an explosion rocked the Farmington No. 9 Mine in northern West Virginia (figure 1). The explosion killed 78 of 99 miners who were working in the mine, including all but one member of the mine's rescue team. Some 30 years after the event, researchers from the NIOSH Pittsburgh Research Laboratory (PRL) conducted a video interview with Danny Kuhn (figure 2), the only Farmington No. 9 mine rescue team member who was not working that day and who did not die in the explosion. According to the Mine Safety and Health Administration (MSHA), there are about 80 underground coal mine rescue teams in the United States, and according to the National Mining Association, there are more than 850 underground coal mines. This represents a significant decrease in both over the past decade. The low number of rescue teams is a concern because serious incidents, though fewer, still happen, and if a disaster occurs, there will be fewer rescue teams to respond. This would result in an increased need to use available human resources very efficiently. Much training to prepare these rescue teams still takes the form of what educators call "teaching to the test." In other words, teams practice in order to win mine rescue contests. This test-oriented approach has traditionally been augmented by interactions with others who have responded to real situations or by participating in actual incidents. Given few incidents and fewer rescue teams from whom to derive enrichment, the preparation of coal mine rescue personnel becomes a problem. Recently, more emphasis has been placed on active learning, such as working out problems in smoke. These sessions more nearly simulate the actual conditions that today's team members might rarely encounter. To properly prepare and retain the current coal mine rescue personnel who are left in the workforce, it is necessary not only to offer such hands-on experience, but also to replace the learning narratives that once were passed from team to team. The present video is intended to contribute in that capacity. Approach NIOSH researchers first learned of Mr. Kuhn in the fall of1998. Mr. Kuhn was contacted and agreed to an interview. An oral history interview was conducted with Mr. Kuhn in early November1998. After reviewing the videotape of the interview, researchers determined the content to be so rich as to warrant a second interview in a more formal setting. The second interview was done in early December 1998. During this interview, Mr. Kuhn spent about 2 hours describing the Farmington disaster, including the workplace climate leading up to the explosion, the events that took place in the 10 days after the explosion, and the nearly 10-year effort to safely and successfully recover most of the victims' bodies. The videotape of the second oral history interview with Danny Kuhn was reviewed and edited by NIOSH researchers for content. Careful attention was used to ensure that valuable information was presented, but within a reasonable timeframe. A detailed map of the Farmington No. 9 Mine was edited into the final video and used to highlight critical features as they were being described by Mr. Kuhn. Results and Accomplishments A 60-minute videotape and instructor's guide for use in safety training or other settings was completed. The target audience consists of all those who work in underground coal mines. This training video will help safety instructors better prepare mine rescue team members for the situations that they will encounter when engaging in extended rescue and recovery work. As a result of this expectations training, team members will be more likely to serve their

Mar 1, 2002

With IIT research institute as a cosponsor, this seventh mineral waste Utilization Symposium was funded by the Bureau of Mines through its Division of Mineral Resources Technology. Environmental scientists and engineers from five countries (Canada, Netherlands, Austria, England, Guatemala) besides the United States participated in the symposium, which was held Oct. 20-21, 1980, at the Chicago campus of IIT Research Institute. Of the 25 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial waste, and scrap metal, 21 are summarized herein.

Jan 1, 1982

By Sigmund Black

Ingersoll-Rand Research, T n c and the Lee-Norse Co. built a Bureau of Mines sponsored, special deep cutting continuous miner under this contract to study the effects of rotational speed and depth of cut on airborne respirable dust. After preliminary tests indicated and later verified that deep cutting - low rotational speed reduces airborne respirable dust, a series of underground tests were performed (9 combinations of rotational speed and depth of cut at 45° bit angle and 4" bit spacing). Additional data was obtained on specific energy, coal sizing and noise. The conclusions reached from the tests results were; a) deep cutting reduces airborne respirable dust generated and specific energy needed to cut coal., b) the greater majority of the decrease occurs in going from 1" to 2" depth of cut, c) lowering rotational speed has a particularly sizable effect of reducing the amount of dust at the operator's location, d) no significant relationship was found for either noise level or coal sizing to rotational speed or depth of cut. Recommendations include. a)) use of specific energy as an indicator of the change in dust level correlating to changes in cutting parameters, b) mine operators should acquire new deep cutting machines., since retrofitting would be selective.

Jan 1, 1977

By R. R. Hornor, Harry E. Tufft

The purpose of this bulletin is to point out some of the benefits and economies to be derived by selecting, preparing, storing, preserving, and utilizing mine timber more carefully and to give some specific information on certain preservatives and processes suitable for mine timber.

Jan 1, 1925

By M. Carrales

This Bureau of Mines report presents information on the sulfur content of crude oil in the United States and in some foreign countries. Data are presented for oil produced in 1971 from fields in 26 States that accounted for about 76 percent of total U.S. oil production; the foreign data cover fields in 24 foreign countries that accounted for about 64 percent of the total oil produced from these countries in 1971. Most of the data are presented in tabular form.

Jan 1, 1975