Search Documents

By John Rusnak, Christopher Mark

Point load testing is used to determine rock strength indexes in geotechnical practice. The point load test apparatus and procedure enables economical testing of core or lump rock samples in either a field or laboratory setting. In order to estimate uniaxial compressive strength, index-to-strength conversion factors are used. These factors have been proposed by various researchers and are dependent upon rock type. This study involved the extensive load frame and point load testing of coal measure rocks in six states. More than 10,000individual test results, from 908 distinct rock units, were used in the study. Rock lithologies were classified into general categories and conversion factors were determined for each category. This allows for intact rock strength data to be made available through point load testing for numerical geotechnical analysis and empirical rock mass classification systems such as the Coal Mine Roof Rating (CMRR).

By A. J. Kraemer, H. M. Thorne

The following account of oil-shale operations in Australia is based upon infor- mation obtained by the authors while visiting Australia from September 15 to October 7, 1947, supplemented by published data, and augmented by analyses of samples of oil shale and its products at the Oil-shale Research and Development Laboratories of the Bureau of Mines at Laramie, Wyo. The primary objective of the authors' trip to Australia was to obtain, first hand, information regarding the equipment and methods used by National Oil Proprie- tary, Ltd., at Glen Davis, New South Wales, in mining oil shale, extracting oil from it, and refining the shale oil. This company was operating the only oil-shale plant that had been active in Australia since 1945. The plant comprised an oil-shale mine, 104 modified Pumpherston (Fell) retorts in 2 batteries, a hele refinery, and a 3-inch gusoline pipeline to the railroad loniing terminal t Sun Junction, 30 miles away. There were, also, the usual and necessary any uralities, such as a power house, mechanical shops, offices, and laboratories One Information regarding the company's operations was wance because of its bear- Ing upon the synthetic liquid fuels program of the Bureau of Mines, pursuant to the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S.C., 321-325, as amended). objective of the Bureau's program. In accordance with the maniate of the Act, is to furnish American industry cost and engineering data necessary for the development of synthetic-liquid fuel industry, and an obvious means of obtaining some of these data is to learn how oil shale is being mined and retorted and how shale oil is re- rined in countries where these operations have been conducted on a plant scale for many years. The authors spent 2 weeks at the plant of National Oil Proprietary, Lt., at Glen Davis, and were afforded every opportunity to obtain letailed and specific information regarding all aspects of the company'a operations.

Jul 1, 1951

By Wing G. Agnew, John A. Johnson

"INTRODUCTION This paper is one of a series being published by the Bureau of Mines pertaining to an investigation on the use of stemming in metal mines now being conducted at the Mount Weather Testing Adit. Its purpose is to compare the amount of dust and gases produced as a result of blasting charges of dynamite (1) in drill holes, (2) in bombs, and (3) in mud-cap or adobe shots.ACKNOWLEDGMENTSValuable assistance and advice on stemming were given by members of the staff at the Bureau of Mines, as acknowledged in previous publications. 4/TEST PROCEDUREThe results used for comparison in this report are from dust and gas samples taken after blasting (1) four regular test rounds with no stemming, (2) five bomb shots, and (3) two mud-cap or adobe shots.The four rounds were the standard 26-hole test rounds designed to break 4 feet of rock. The procedure for drilling and blasting these rounds is described in Report of Investigations 3509.Before the regular test rounds were blasted, about 1,200 bounds of fine rock was placed on the steel mucking sheets that covered the end of the adit track; the wails, hack, and floor of the adit were washed thoroughly; and the fine rock on the mucking sheets was completely wetted.Each of the 5 bomb shots consisted of 10 sticks of dynamite tied together and hung at midpoint of the adit, 8 feet from the fall."

Dec 1, 1942

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson, County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut, coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 316-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an. extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

By A. W. Frolli

This paper, describing the open-cut mining milling, and cyaniding methods and costs at the Yellow Aster gold mine, is one of a series being prepared by the Bureau of Mines on similar practices in the United States. It is presented primarily to show methods and costs of mining and treating low-grade gold ore on a large scale.

Jan 1, 1940

By Paul G. Marinos, Vassilis Marinos, Evert Hoek

The Geological Strength Index (GSI) is a system of rock mass characterization that has been developed in engineering rock mechanics to meet the need for reliable input data related to rock mass properties required as input for numerical analysis or closed-form solutions for designing tunnels, slopes, or foundations in rocks. The geological character of the rock material, together with the visual assessment of the mass it forms, is used as a direct input for the selection of parameters for predicting rock mass strength and deformability. This approach enables a rock mass to be considered as a mechanical continuum without losing the influence that geology has on its mechanical properties. It also provides a field method for characterizing difficult-to-describe rock masses. Recommendations on the use of GSI are given and, in addition, cases where the GSI is not applicable are discussed.

Jan 5, 2007

By R. A. Beall

This bulletin reviews the historical background of the cold-mold arc-melting technology, with specific references to the development that led to homogeneous zirconium ingots. Descriptions are given of modern production arc-furnaces for vacuum melting of troth exotic and conventional metals. Besides zirconium, specific data are given for production of chromium, thorium, and copper. The development of the skull-casting technique for titanium is detailed, and the application of the technique to such refractory metals as molybdenum and tungsten is described. Factors of operation of the apparatus and furnace design are considered.

Jan 1, 1968

By R. S. Dean

[During the past fiscal year the Metallurgical Division has made important contributions along the lines dictated by the Bureau policy of conservation of domestic mineral resources through Its investigations include determining of fundamental data of metallurgically important materials improvement of standard ore-treatment method to eliminate waste and improve the grade or recovery of the products; and development o new metallurgical processes.]

Jan 1, 1940

By R. S. Dean

[During t!~c past f isc.~l y~:-.r the Xetzllvz-gicd 3ivi oion has made im- portant contribution-, don,- tlie lines rlictnteil by the Bureau policy of con- servation of domestic rnker~l rcsoul-ces throui;h use. During t!~c past f isc.~l y~:-.r the Xetzllvz-gicd 3ivi oion has made im- portant contribution-, don,- tlie lines rlictnteil by the Bureau policy of con- servation of domestic rnker~l rcsoul-ces throui;h use.]

Jan 1, 1940

1. Domestic Production and Use: Twelve companies operated 31 primary aluminum reduction plants, three firms accounting for 66% of production. Washington, Oregon, and Montana accounted for 32% of the total production; Gulf Coast States, 25%; Northern States, 29%; and other Southern States, 14%. Output of primary metal in 1973 was valued at $2.2 billion. About 80% of the secondary recovery was from new aluminum base scrap and 20% was from old scrap. Aluminum consumption by 25,000 firms was centered in the East Central United States. Of aluminum consuming industries in 1972, building accounted for 28%; transportation 19%; electrical, 13%; packaging, 16%; and consumer durab1es, 10%.

Jan 1, 1974

By E. O. Wagner, A. W. Koth, V. F. Parry, J. B. Goodman, D. C. Gernies

"INTRODUCTION A commercial-scale pilot plant for gasification of lignite was completed by the Bureau of Mines at Grand Forks, N. Dak., early in 1945 as an extension of work on, gasification of low-rank coals initiated in a smaller pilot plant at Golden, Colo., during 1943. The development work on this plant was part of a program to make reducing gases from lignite for beneficiation of low-grade iron ores. The background of this project has been described in a previous report. 6/ The present report describes the major features of the large pilot plant, a record of experimental operating data during five runs totaling about 1,800 hours, .and results of experimental work on the small pilot plant at Golden during 1945.This project has created considerable interest because heretofore there has been little success in several attempts to gasify American lignites.Furthermore, the methed employed is a departure from conventional processes. Natural lignite is fed continuously into an externally heated annular retort and is converted into water gas by heat conducted through alloy metal walls. Because of the high thermal conductivity of metal, the rate of gasification is several times greater than can be obtained when employing refractory walls. The process has been developed to a part that leaves one major question unanswered. - ""How long will the alloy last under practical operating conditions?"" - and this question has aroussed the interest of the Coal Division of the Bureau of Mines in this new development.Owing to the high reactivity of the lower-rank fuels, the water-gas reactions proceed rapidly at medium temperatures of 1,650°F. to 1,800°F. These temperatures can be attained in a reaction zone heated by external means when the temperature of the retort does not exceed 1,900°F. while transferring from 6,000 to 7,000 B.t.u. per hour per square foot. Such rates are several times greater than can be attained through refractory walls as employed in the Didier-Bubaig 7/ and the Ahrens processes. 7/ Therefore, the investment cost of the gas generator per unit of capacity will be considerably lower for the higher-capacity process. However, the maintenance cost of metal vessels will be higher than that of refractory retorts, and this emphasizes the importance of large-scale operation to determine the life of an alloy retort under practical operating. conditions."

Sep 1, 1947

By H. L. Gilbert

Improvements in production of high-purity chromium metal by magnesium reduction of anhydrous chlorides and by hydrogen treatment of electrolytic chromium are reported. Hydrogen-treated chromium has been arc-melted, and the arc-melted material has been successfully forged, rolled, and swaged. The material also has been forged at liquid-air temperatures. X-ray and metallographic studies indicate the recrystallization temperature of rolled chromium sheet to be about 750° C. Preliminary investigation of hot-bending characteristics of rolled chromium sheet shows the minimum bending temperature to be about 325° C. The heat resistance of chromium has been investigated.

Jan 1, 1952

By H. M. Lawrence, E. Roca

"INTRODUCTION Of the phosphate rock deposits of the United States that are being exploited actively at present, the land-pebble area in Florida is the largest producer. In recent years the land-pebble district, in Polk and Hillsborough Counties, has produced about 80 per cent of the raw phosphate rock that has supplied the requirements of the several national industries based on this essential commodity.In the land-pebble deposits sizes finer than 16 to 22 mesh are below the commercial limit in phosphate content, and washing-plant practice has been directed to the recovery of the coarser material. Recently, more extensive control of the washery plan has resulted in the saving of additional amounts of phosphate, the loss of which had been considered unavoidable. However, strict requirements of the trade regarding the lowest acceptable grade of phosphate rock prevent the inclusion of more than a very small proportion of the low-grade phosphatic sands with the washery output of phosphate roe:. Further advances in practice resulting in larger recoveries of phosphate can only be effected by the application of processes that are based on other principles than merely a difference of particle size. Research is be conducted actively along these lines by the industry and by cooperating agencies.Flotation has been studied for several years by the International Agricultural Corporation and its allied company, the Phosphate Recovery Corporation. J. T. Burrows, vice-president of the International Agricultural Corporation, in a letter dated July 10, 1929, states:"

Aug 1, 1931

By L. L. Hirst

Liquid fuel oils possess certain advantages over solid fuels. Ease in handling, precision temperature control, and almost complete freedom from ash are among those considered when a liquid fuel is selected for use in industrial processing. In some instances these fuels are desirable because more heating units can e packed in a Given space where space is limited, as on snips. In other cases the' are chosen because of lower actual cost per British thermal unit absorbed, or for control of the flame to increase the capacity of furnaces, as in steel and refining.

Jan 1, 1948

By G. S. Beaumont

This report presents a programme of work to demonstrate the use of a surface-based centralised computer control system for the remote monitoring and control of underground conveyors in a US coal mine. The system selected for demonstration was the 'Dynalink' Micro MINOS system which is manufactured by Hawker Siddeley Dynamics Engineering Limited. The site selected was Barnes S Tucker Lancashire No. 20 Mine located near Carrolltown, Cambria County, Pennsylvania. The system concept, operating and application software was designed and developed by the. British National Coal Board. The report describes the selection of the site, specification of the system requirements, commissioning, operation and evaluation of the system under typical US mine operating conditions. Experience with the system, based primarily on the system reliability and performance of conveyor control, was favourable. Mine management personnel felt that the system had successfully achieved its objectives and were keen to expand monitoring and control to other activities.

Jan 1, 1986

By Branch of Editorial Services

"The Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau of Mines to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue of the Bureau of Mines List of Publications and Articles describes reports and articles published during the period January 1, 1980, to December 31, 1984. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960;1 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960;2 the 5-year lists of publications and articles from January 1, 1960, to December 31, 1964,3 from January 1, 1965, to December 31, 1969,4 from January 1, 1970, to December 31, 1974,5 and from January 1, 1975, to December 31, 1979;6 and the annual lists of Bureau publications and articles from January 1 to December 31, 1980,7 from January 1 to December 31, 1981,8 from January 1 to December 31, 1982,9 and from January 1 to December 31, 1983. 10"

Jan 1, 1985

By H. Tomlinson

"PURPOSE OF REPORTThe purpose of this report, which is the third of a. series on the coal mines of the Western States, is to give the findings of a study of the causes and methods of prevention of accidents from falls of root and coal in the mines of Lincoln County, Wyo. The three mines covered in this report, referred to as A. B. and C, account- for 9 per cent of the coal production in the county and nearly 9 per cent of the State's total production. For comparative purposes some statistical data are presented bearing upon the relation of injuries to their causes, to tonnage produced, to men employed, to days worked, and to days lost as the result of injuries.FATALITIES IN WYOMINGTo show the necessity for this study, Table 1 given the fatalities that occurred during 1928 in the bituminous—coal mines of the United States, of the State of Wyoming of Lincoln County, and in Mines A, B, and C, followed by a brief description of the Kemmerer coal dis-trict, its coal beds and immediate roof, thickness of cover, dip of coal beds, methods of mining timbering for roof support, roof testing, and supervision. All of these factors must be considered in any plan outlined to prevent accidents resulting from falls of roof and coal.ACKNOWLEDGMENTAcknowledgment is made to the officials of the operating companies for their cooperation and assistance during the study and collection of data to complete this report.GENERAL INFORMATIONLocation and Ownership The mines included in this report are within 18 miles north and south of Kemmerer, Lincoln County, Wyo. (fig. 1), and are owned and operated by various coal companies to supply the domestic, smelter and railroad markets. They are severed by branch lines of the Oregon Shorty Line Railroad Coal production and men employed underground in the three mines are indicated in essential detail in Table 2."

Sep 1, 1932

By W. W. Adams

"The ninth yearly National Safety Competition covering the calendar year 1933, conducted by the United States Bureau of Mines, w participated in by 332 mines and quarries situated in 35 States. Enrollment represented as increase of 10 plants over 1932, and one addition was made to the number of States represented.The primary purpose of the United. States Bureau of Mines in conducting the contest is to promote safety in United States mineral industries. This purpose is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive recognition on a national scale for their achievement the purpose is accomplished indirectly through studies by the United States Bureau of Mines of the facts contained in the accident reports the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics which constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting, from industrial accidents.Bronze trophies, known as 'Sentinels of Safety', which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines, were presented to five companies in the contest of 1933, each company having established the best accident-prevention record within one of the five classes into which all companies were divided, namely, anthracite-mining companies, bituminous-coal-mining companies, metal-mining companies, operators of nonmetallic-mineral mines other than coal mines, and quarries or opencut mines. The trophies are awarded for 1 year and are then transferred to the winners of the succeeding year's contest.The trophy for bituincus-coal mines was won by a company in Wyoming. A company in Tennessee won the trophy for metal mining. In the nonmetal-mine group the trophy was again won by a company in New York. A quarry in Michigan won the trophy for the quarry-and-opencut-mine group. The trophy for anthracite mines remains in Pennsylvania, as all anthracite mines in the contest are in that State."

Jul 1, 1934

By R. E. Chaney

This report summarizes the research on the Strategic and Critical Materials Program tasks conducted at the Idaho National Engineering Laboratory (INEL) between May 1984 and April 1985. The work is divided into two areas: 1. Production Technologies - Tasks directed at developing advanced extraction technologies ? Biologically-Assisted Minerals Processing ? Metal/Gas Reactions and Thermal Plasmas ? Dehydration of Aluminum Chloride Hexahydrate (completed). 2. Conservation/Substitution Technologies - Tasks directed toward establishing the technical processing base which will permit the use of advanced materials ? Joining of Rapidly Solidified Alloys (RSA) ? Joining of Silicon Nitride-Based Ceramics ? Nondestructive Evaluation of Ceramic and RSA Joints and Materials ? Substitute Catalytic Materials for Platinum.

Jan 1, 1985

By J. A. HUFF, V. V. BAKER

This circular is intended to present in brief form the statutory provisions of Pennsylvania regarding mining operations, in force at the end of the 1931 session of the legislature. lo reference is made to general laws which affect mining only incidentally in common with other subjects, such as the workmens compensation law. The statements have been condensed as far as practicable, and provisions not deemed of general interest, such as matters dealing only with administrative details, have been omitted. This circular obviously is not written with such particularity as to be of great value to the legal profession, but it is hoped that it will be beneficial to the mining industry in giving this information in a relatively compact form. At the end of each paragraph the statute from which it is derived is cited to facilitate reference to the text of the law. It is planned to publish additional circulars from time to time dealing with the mining laws of other States. Any criticisms of the form of publica- tion followed herein, or suggestions aimed at the improvement of future circulars, will be welcomed.

Nov 1, 1932