Search Documents

By A. G. Waters, N. J. Bristow

A comparative study was made of an untreated and a heated haematite ore and a sinter produced from a feed consisting of 100% ore, to study the influence on reduction behaviour of sinter bonding phases such as SFCA (silico-ferrite of calcium and alumina). Under low-temperature reduction conditions the order of increasing reducibility followed that of increasing porosity and surface area but under similar conditions at 900 degrees C the sinter exhibited higher reducibility than the ores even though the total porosity and chemical reducibility of the individual phases were lower. This behaviour can be explained in terms of the higher total porosity of the natural ore at low temperatures and the higher level of fine pores in the sinter at high temperatures due to the presence of SFCA, which acts to support the fine (c.0.1 micrometre) pores created by the reduction process. This leads to the conclusion that the main role of SFCA in sinter during high-temperature reduction is to maintain a high level of fine porosity. Some implications of this work for granule design and sintering practice are discussed

Apr 1, 1991

By R. W. Ruddle

The advent of new methods of roasting, “flash roasting and fluidisation”, which are now under development, combined with the use of oxygen-enriched air, may markedly increase the SO2 content of roaster smokes. Skogmo suggests that the production of smokes containing as much as 50 per cent SO2 should be feasible. The use of flash smelting processes may well enable a similar increase in the SO2 content of smelter smokes to be made. In this event the recovery of sulphur would be greatly cheapened and the process might well be much more economic, even if allowance is made for the cost of generating the oxygen

Jan 1, 1953

By A. H. G. Mitchell

Gold-poor and gold-rich porphyry and epithermal gold-silver deposits of Caenozoic and Cretaceous age in the western Pacific and central and eastern Europe are confined to predominantly andesitic continental margins and island arcs. The arc volcanic rocks overlie a complex non-oceanic basement of stacked nappes, the uppermost of which is often ophiolitic. The emplacement of ophiolite triggered a reversal of tectonic polarity, subduction and arc magmatism. Andesitic volcanism and the formation of a strato-volcano were followed by the ascent of magma and porphyry copper mineralisation. Regional propylitic alteration came from convecting, predominantly meteoric fluids. Magmatic degassing caused advanced argillic alteration. This is commonly unmineralised in perched water tables, but may sometimes host high sulphidation gold or enargite gold at deeper levels within the propylitic zone. The onset of extensional stress after the andesitic volcanism allowed meteoric water to circulate to depths of 5 km or more, with consequent cooling of an ascending magma body at depth and the development of low sulphidation epithermal gold mineralisation near and immediately above the sub-volcanic basement surface. All andesitic arcs are mineralised. Regional controls on their ore potential include the level of erosion and geological features in the basement that focus the ascent of fluids. Differences between the mineralisation of the European and the western Pacific arcs may reflect the presence of older, more granitic basements in many of the European arcs.

Jan 12, 1992

By S. K. Chaulya, R. S. Singh, B. B. Dhar

Two prominent local species, Dendrocalmus strictus (bamboo) and Saccharum spontaneum (kashi), and two exotic species, Cymbopogon citratus (lemon grass) and Vetiveria zizanoides (vetiver), were selected for growth trials on dumps at Mandaman, Chora, Mudidih, South Balanda and Ghugus. The climate at these sites is dry tropical and the surface soil layer a slightly acid to neutral sandy to clayey loam 10-11 cm thick, impoverished in major plant nutrients. After two years bamboo had grown the most, up to 325 cm in height, and contributed the greatest biomass, 638 g/m2 of plant. The local kashi species had a very good regenerative capacity, which was lacking in the lemon grass and vetiver. The grasses had very good soil-binding capacity and could also provide income if used as cash crops

Jun 21, 1905

By D. Mireku-Gyimah, R. S. Suglo

Ghana contains auriferous belts which cover 51 800 km2 of its small area of 239 400 km2. From 1493 to 1600 35.5% of the world gold production was from the Gold Coast (renamed Ghana in 1957). This dropped to 8.9% from 1701-1800. For the past fifteen years annual production has averaged less than 2% of the world total. By 1985 only four gold mines were operating, compared with 45 in 1934 and 11 in 1945. Since 1987 Ghana has experienced a boom in gold mining activities. By 1991, 83 new companies had acquired prospecting licences. At least five new companies have started large-scale production. About 650 licensed small-scale mining groups are in operation. The economic and technological factors that have contributed to the decline of gold production in Ghana are discussed. A summary is given of the methods used to mine and recover gold. These cover small-scale workings, dredging, open cast operations and underground mining. The advantages and disadvantages of these technologies and the future of gold mining in Ghana are considered.

Jan 4, 1993

By V. E. Ross

A comparison was made of three methods for determining the contributions of true flotation and entrainment during batch flotation tests. In the first method size-by-size recoveries are measured in both the presence and the absence of a collector, a frother being present in both tests. In the second method the mass of solids and water recovered after a chosen time of flotation is varied by changing the rate of froth removal and the depth of the froth. The third method uses a transfer factor to describe the classification of solids and water, and hence the changes in the composition of the pulp, during a single flotation test. Batch flotation tests were carried out with artificial mixtures of pyrite and gangue, the amount of floated material recovered being calculated according to each of the three methods. The discrepancies betweeen the calculated amounts are analysed in terms of the assumptions that are made for the various methods and the most suitable conditions for the application of each method are identified

Dec 1, 1991

By J. Ostwald, L. T. Matthews, C. E. Loo

Australia has large reserves of pisolitic limonite. Mining recently commenced on the Yandicoogina deposit to produce a high-grade sintering ore. The ore contains about 10 wt% combined water and simulated sintering temperature profiles indicate that progressive dehydration of ore particles occurs in the temperature range 300-700 degrees C. Studies by optical microscopy show that although the dehyrdrated ore particles contain numerous cracks, there is no change in the microstructure of the ore because topotactic transformation to haematite results in the formation of compact masses of very fine-grained haematite microcrysts. When the ore is held at around 1 200 degrees C for 1 min significant recrystallisation of these microcrysts occurs, resulting in the formation of optically visible, micrometre sized haematite crystallites. Studies to simulate the behaviour of ore particles during sintering (as nuclear particles surrounded by a standard adhering fines mixture) show that the recrystallisation process occurs much earlier at temperatures of about 900 degrees C. Further studies indicate that CaO in the adhering fines mixture enhances the recrystallisation of the ore nuclei. The results of the investigation indicate that the pseudo-relict haematite in sinters produced from ore blends that contain significant levels of pisolitic limonite consists of dehydrated goethite that has undergone significant recrystallisation and grain growth, a phenomenon that is facilitated by the presence of lime derived from the sintering melt.

Jan 12, 1992

By Tuncel M. Yegulalp, Selamet G. Ergelebi

A description is given of a method of analysing modern mining systems in terms of reliability and their effects on productivity. Non-exponential distributions, such as the Weibull and lognormal distributions, for failure and equipment repair times are also considered. The resulting non-homogeneous Markov process is solved by the method of stages. A longwall mining system is analysed as an example.

Jan 4, 1993

By A. Paulin, A. W. D. Hills

The work has shown that packed-bed behaviour can be predicted from the results of single-particle experiments, total reaction times being predicted somewhat more accurately than gas and solid temperatures and gas compositions. A small laboratory packed-bed reactor was built and used to study the decomposition of beds of specially prepared CaCO3 spheres, steps being taken to minimise the effects exerted by the walls of the bed on processes occurring within the bed. Gas and solid temperatures and gas compositions were measured at various points in the bed and compared with theoretical predictions based on kinetic data determined in previous single-particle experiments. The measured solid temperatures and total reaction times agreed remarkably well with the values predicted theoretically. Gas and solid temperatures measured after the reaction had finished at any point in the bed did not agree with the theory. This was because solid temperatures in the bed rose very rapidly once the reaction was completed and the walls of the bed could not be heated at a sufficient rate for their temperatures to rise as rapidly; thus some loss of heat from the bed to the walls was inevitable, and this could not be accounted for in the theory. In addition, the theory did not allow for the conduction of heat within the bed, and this resulted in some further slight discrepancy between the measured and predicted values, particularly after the reaction was completed. Gas compositions measured in the bed were rather scattered, but, even so, they agreed moderately well with the predictions of the theory.

Dec 1, 1971

By G. E. Pearse

Reports, discussions, a written contribution and two written replies are presented from 11 sessions on: Safety and compressed air; Ground movements; Geotechnical; Channel Tunnel (2 sessions); Machines; Case histories; Transport tunnels; Case studies; Site investigation; and Undersea tunnels

Jun 13, 1905

By K. El-Barawi, Hussein M. Kamal

Chlorination was performed of iron-rich chromite ore from Barramyia, United Arab Republic (UAR), together with its concentrate. The effects of change of grain size, chlorine gas flow rate, time and temperature were studied. The extent and mechanism of chlorination were followed through chemical and structural analyses of the feeds and complete chemical analysis of the chlorination products. By conducting the chlorination process for short periods at 600°C or lower temperatures, products having high Cr-Fe ratios suitable for ferrochrome production can be obtained.

Dec 1, 1971

By C. A. Pickles, S. J. Splinter, J. Cameron

The addition of copper oxide to a borosilicate slag resulted in the breakdown of the silicate network and a dramatic decrease in viscosity. With increasing borax to silica ratio the viscosity was reduced by two mechanisms. First, rising sodium oxide content promoted cleavage of the Si-O bonds. Second, increasing boric oxide (B2O3) content increased the number of trigonal borate units that were converted to tetrahedral borate units by sodium oxide and copper oxide. The BO4(4-) tetrahedra decreased the local silicate symmetry, thus disrupting the silicate network and lowering the viscosity. The activation energy decreased with increasing temperature and increasing copper oxide content

Jun 13, 1905

By Winmill T. F.

(Paper presented at the Institution of Mining Engineers' general meeting held in London on 8th June 1916.) The conclusions reached in this paper may be summarized briefly as follows: (1) The method of estimating moisture in coal by determining the loss in weight of a sample heated to 105°-110° Cent, in an air-bath for an hour is untrustworthy, the results so obtained being too low. (2) Dried coal has a very considerable power of absorbing moisture, and a sample, after being dried, must be protected instantly if it is to remain free from moisture. (3) A fairly accurate estimation may be made by heating the coal in a current of dry air at 105° to 110° Cent., and collecting the moisture evolved. (4) In cases in which it is proposed to use the dried coal for any further experiments, the drying must be done in the absence of oxygen, and this can be done simply and quickly by the vacuum method now described

Dec 1, 1916

By A. W. Fletcher

Report of discussion at February, 1971, IMM general meeting (Chairman: M. J, Cahalan President) of a paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, December, 1970, pp. C247-52, and contributed remarks. Contributions are included from: Cahalan M.J., giving figures related to leaching Cu from pyrite at Rio Tinto 1880-1910; Noakes F.D.L.; Embling P.M.K.; Bradshaw A.V.; Le Roux N.W.; Kelly D.P.; and Tuovinen O.H. Questions were raised regarding impurity removal, effects of light and ultraviolet light on the bacteria, the economics of solvent extraction and the possibilities for other organisms or other metals

Dec 1, 1971

By D. D. Lei, H. Sevim

Long-term production planning in open-pit mines requires the determination of cut-off grade, mining and milling production rates, a mining sequence, mine life and ultimate pit limits. Since these variables interact in a circular fashion, a genuine solution to the problem necessitates their simultaneous determination. A methodology with this capability is described. This comprises a group of heuristic algorithms and an unconventional dynamic programming algorithm. The method is demonstrated using data for a gold deposit in the western USA

Jul 1, 1996

By W. J. Whiten, D. W. Grinsberg

Most cluster analysis techniques are not well suited to the analysis of engineering data as they have been designed for more qualitative data that tend to produce compact clusters. A clustering technique is described which develops and uses local cluster shapes to build clusters that are suitable for use in engineering applications. The technique is finding application in the analysis of many types of data, particularly where multiple trends and outlying points occur in multiple dimensions. Applications of particular interest are the calibration of on-stream analytical equipment and the analysis of data on plant performance. In both cases the multidimensional nature of the data renders manual analysis very difficult

Dec 1, 1991

By Winmill T. F.

Paper presented at the at the Institution of Mining Engineers' general meeting held in London on 8th June 1916: In a previous paper it has been shown that the rate of absorption of oxygen by coal is neither directly proportional to the surface area of the coal exposed nor to the percentage of oxygen in the air. Further experiments are now described supporting this conclusion

Dec 1, 1916

By T. Sharma, T. C. Rao

Laboratory studies have been carried out on acid leaching as a possible route for the extraction of potassium from glauconitic sandstone. Leaching efficiencies with sulphuric, hydrochloric and nitric acids were investigated. The effects on potassium dissolution of temperature, concentration and type of acid, stirring speed and leaching time were also studied. The results show that it is possible to recover 87.5, 93 and 85% potassium with 5 M H2SO4, HCl and HNO3, respectively. During the initial stages of the sulphuric acid leaching process the chemical reaction at the mineral surface is the rate determining step, whereas during the later stages diffusion through the product layer is rate-controlling. Overall, the process follows a mixed-control model that includes both chemical reaction and diffusion. The activation energy for the dissolution of K was found to be in the range 25.79-106 kJ/mol.

Jan 12, 1992

By R. Scheepers, J. E. Misiewicz, A. C. Fitzgerald

Discussion by A.C. Fitzgerald of the paper, published in Trans. IMM A, vol.104, 1995, p.B121-B135, is presented together with the authors' response. Fitzgerald points out a number of problems with the idea of mineralising fluids leaving no trace in the large volumes of rock traversed before depositing all minerals of value in a particular horizon or rock type with which the required isobaric or isothermic surface also coincides. He suggested that in the case of the Rooiberg tin deposits, the Lebowa Granites may be batholiths that reached the surface and were capped by sheets of their own volcanics. The authors agree that they had considered a possible syngenetic origin for the stratabound deposits, explain that no conclusive evidence for this could be found, discuss the relative ages of the sediments and volcanics of the Rooiberg Fragment and explain the role of its low-intensity deformation and flat dip in the coincidence of an isobaric-isothermic surface with the lithological stratification

Jun 18, 1905

By R. N. Pryor, S. H. Shaw, D. L. Dowie, S. H. U. Bowie, M. J. Cahalan, S. F. Gandar

It is concluded that land-based mineral resources will be adequate for most minerals in the immediate future, but in the long term more minerals will come from offshore locations. Because the oceans are international and can transport pollution, international control of offshore workings will be necessary. In the UK and similarly highly developed areas, the working of low-value bulk minerals will create increasing problems in urban development and countryside preservation. Much more information should be published on standards to be adopted and their costs, if emotional social pressures founded on ignorance are to be avoided. The Town and Country Planning Acts have greatly improved the environmental quality in Britain in relation to mineral working. In the long term conservation of some minerals in short supply may be necessary on a national or international basis. Much research is required for the determination of adequate criteria and standards for the preservation of environmental quality in the mineral industry. New local, national and international legislation will be required and the adoption of voluntary standards by trade associations should be encouraged wherever appropriate

Dec 1, 1971