Search Documents

By D. W. Feng

Thiosulfate as an alternative lixiviant for gold has received much attention in recent years due to the growing environmental concerns over the use of cyanide. Cu(II) is used to catalyze the oxidation of gold and ammonia is to stabilize Cu(II) in alkaline solution. However, the presence of Cu(II) enhances the oxidative degradation of thiosulfate. The high consumption of reagents has made thiosulfate leaching uneconomical to date, in comparison with cyanide leaching. Therefore, further investigations are required to leaching under low reagent concentrations over extended periods where reagent consumption is low and gold leaching rate is low as well. It is thus necessary to find additives to enhance gold dissolution in the thiosulfate leaching system. Electrochemical studies using rotating gold disc showed that the oxidation of gold in ammoniacal thiosulfate solution increased significantly in the presence of a small amount of thiourea and the beneficial effect increased with an increase in the thiourea concentration up to 7.2 mM. Thiourea improved gold extraction in the thiosulfate leaching of gold from a sulfide ore under low reagent concentrations. Excessive addition of thiourea inhibited the leaching of the gold ore. The decomposition of thiosulfate was reduced with the presence of thiourea. X-ray Photoelectron Spectroscopy (XPS) results indicated that thiou-rea likely decomposed to sulfide and formed gold sulfide species at the gold surface.

Jan 1, 2014

By Q. X. Li

The state discharge standard for arsenic-containing wastewater which is the first kind of pollution is less than 0.5 mg/L. In fact, in a certain company, the acidic arsenic-containing wastewater in non-ferrous smelting was as high as 860 mg/L, which is far beyond the state discharge standard. Obviously, the direct release of this wastewater without further treatment would result in great hazards to the ecological environment. To aim directly at the characteristics of acidic arsenic-containing wastewater, in this study, two steps of treatment including oxidation-flocculation and removal fluoride by mixing alkaline neutralization were suggested. Through analyzing various influencing factors in treatment effects, the optimum technical conditions were obtained. The sediments after treating were recyclable and the secondary pollutions can be avoided. Moreover, the results also show that, all indexes of the effluent after treating are lower than the First Grade Standard of Integrated Wastewater Discharge (GB 8978-1996). This novel method has advantages of short flow sheet, easy operation and low cost.

Jan 1, 2014

By M. Zolghadri

MIBC and sodium metasilicate are used as a frother and a dispersant in coal flotation respectively. In order to study interaction between them, flotation experiments were performed on fine coal (<150 microns). It was found that if the frother (MIBC) dosage is in excess of a certain limit, it has an activation effect on the gangue minerals associated with coal. In addition, it was found that however sodium metasilicate can disperse clay slimes eliminating slime coating, but in the case of excess dosage, could intensify activation effect of MIBC, which is undesirable in coal flotation. Keywords: coal flotation, sodium silicate, frother, dispersion, activation

Sep 1, 2012

By G. W. Zhang

Ultra-fine Stirred Mill is a kind of high energy efficient equipment for ultra-fine grinding, and has been the mainstream equipment in the submicron powder and slurry industry. This paper mainly describes flow-field numerical simulation of the three popular ultra-fine grinding mills: (respective-ly as) Disc Stirred Mill, Pin Stirred Mill and Spiral Stirred Mill, by means of the software Computational Fluid Dynamics (CFD). In the flow-field numerical simulation, the velocity gradient, shear rate dispersion of the flow-field, the viscosity dissipation rate were analyzed with CFD. It is discovered that Pin Stirred Mill has the highest velocity gradient in circular directions and the most homogeneous distribution of shear rate among the three. Flow-field numerical simulation provides a new way (and means to) for the parameter optimization design and project enlargement of Ultra-fine Stirred Mill. The experiments were also carried out, the results are consistent with the results of the simulation analysis. For example, in GCC grinding experiments under the same conditions, the specific energy consumption of Pin Stirred Mill with 3600L in volume is 15%~17% less, and its processing capability is 13%~15% better than Disc Stirred Mill. Now with its optimized structure and excellent performances, more than ten sets Pin Stirred Mill with 3600L in volume have been used in industrial production in Shandong, Guangdong and Hunan province.

Jan 1, 2014

"This research aims at improving the beneficiation of coals and minerals in fine and ultrafine size fractions. A widely used method for upgrading fine and ultrafine particles is froth flotation, which is generally classified into mechanical flotation and column flotation. The present work is focussed on column flotation. A flotation column equipped with a conventional bubble diffuser/sparger was used with oscillatory air supply generated using a fast-switching solenoid valve. The flotation tests were carried out for coal particles and mineral particles, respectively, and a comparison in flotation performance was made between oscillatory air supply and steady air supply. It was found that use of oscillatory air supply with a proper valve switching frequency and on/off time ratio to replace steady air supply could lead to increased recovery of coals or minerals by more than 14 percentage points and substantial reagent cost savings. The improved flotation performance was attributed to enhanced gas dispersion and flow conditions. This research offers a simple new approach to improving the beneficiation of fine coals and minerals with using flotation columns.INTRODUCTIONFroth flotation has been widely used for the separation and concentration of fine coals and minerals by exploiting the difference in their affinity to air bubbles in aqueous medium. Froth flotation is an effective method for beneficiation of coal and mineral particles in a certain size range. It remains difficult to upgrade ultrafine mineral particles. One of the reasons for the ineffective flotation of fine particles is the low probability of bubble-particle collision in the collection zone (i.e., the pulp zone). According to Reay and Ratcliff (1973) and Yoon and Luttrell (1989), the probability of collision is significantly affected by bubble size and particle size, and the collection zone recovery can be increased by decreasing the bubble size."

Jan 1, 2018

By R. S. Wang, S. Z. Zhou, L. Wan, K. W. Zeng, Z. J. Sun, W. G. Wu, Z. B. Qian, X. R. Zhang, Z. K. Hu, Y. Yu

"In view of the present situation that the traditional environment friendly depressants for galena aren’t very effective in the separation of mixed concentrate including copper sulfide and lead sulfide, this research describes a new environment friendly depressant PD-1 and investigates its effects and mechanism in the separation of chalcopyrite and galena. This study is carried out through flotation tests, analysis of infrared spectra and absorption measurements. It is shown that when O-isopropyl-N-ethyl thionocarbamate (Z200) is used as collector, chalcopyrite and galena can be separated in the presence of PD-1 under appropriate conditions. Therefore, it can be concluded that PD-1 has an excellent depression ability and great selectivity for galena. Meanwhile, analysis of infrared spectra demonstrates that PD-1 can strongly absorb on the galena surface by chemical interaction with Pb2+, while it hardly absorbs on the chalcopyrite surface. In addition, the results of absorption measurements reveal that competitive adsorption occurs on the galena surface between PD-1 and Z200, PD-1 can block the absorption of Z200 on the galena surface. However, PD-1 has a little effect on the absorption of Z200 on the chalcopyrite surface under above conditions. What’s more, the hydrophilic groups of PD-1 molecules can make galena effectively depressed. The results of mechanism analysis are in accordance with those of flotation tests.INTRODUCTION In the processing of copper-lead sulfide ores, the process, copper increase and lead reduction (Zhang et al., 2017) after reagents removal of rough concentrate produced by mixed flotation of chalcopyrite and galena, is usually adopted. However, as a result of tight symbiosis and the similar flotability of chalcopyrite and galena, the separation is difficult (Hu and Feng, 2006). There are 3 kinds of depressants for galena in the separation of chalcopyrite and galena concentrate,including dichromate, sulfite and combined depressants of organic or inorganic reagents (Wei, 2012). As dichromate would cause serious environmental pollution, it is gradually banned to be used in industry (Xu et al., 2017; Lin et al., 2017). what’s more, due to the need of acidic slurry, using sulfite is not conductive to the maintenance of equipment and stable production(Wang, 1999). As for the combined depressants, they also have disadvantages of complex pharmaceutical system and no ideal separation effect (Wei and Sun, 2008). Therefore, the development of new safe and effective depressants for galena is a research focus for researchers in the minerals processing (Chen, 2000). In this paper, a new type of organic depressant PD-1 is applied to the copper-lead separation process of ""copper increase and lead reduction"" using Z200 as the collector. In addition, the performances and mechanism of its depression to galena are studied emphatically."

Jan 1, 2018

By U. M. J. Boin, E. V. Verhoef

Pyrometallurgical reactors constitute a key processing component in the total primary and industrial/recycling resource cycle, being involved both in primary smelting, converting and extraction, as well as the reprocessing of scrap, from aluminium cans to end-of-life automobiles. Therefore the pyrometallurgical reactor?s role in achieving sustainability is the central theme discussed in this paper since optimising their operation minimises waste, residue and offgas (NOx, dioxin, CO2) and maximises product quality and therefore efficiency. To effectively control the overall resource cycle, one needs to take a systems modelling approach of the whole cycle, seeking to also understand the dynamic process behaviour of the individual components of the cycle, and then especially the part that contributes most to the chemical conversion, namely the pyrometallurgical reactor. This paper highlights the role of pyrometallurgical thermodynamics in the whole resource cycle and specifically places equilibrium thermochemistry in the context of process dynamics where large, variable inventories are recycled or maintained within the system. This paper will therefore review the semi-empirical dynamic modelling tools, which are used to model complex systems with the specific goal of developing dynamic predictive models, which also include slag-alloy chemistry, towards controlling the recycling in a feed forward manner. To illustrate the primary production of metals, high carbon ferrochrome and Ni-Cu-matte smelting will be presented as a brief case study. Also fundamental studies in blast furnace and waste incineration kilns will be given. It also will show how the distributed nature of the chemistry of melts in the case of primary extraction, and industrial (recycling) materials such as recycled end-of-life vehicles, have a significant impact on the process outcomes and model predictions. It is therefore argued that the fundamental thermodynamics and kinetics in metallurgical reactors play a final crucial role in modelling the closed material cycle, but only when it is used in conjunction with process systems theory based on reconciled data for parameter estimation and model calibration. System models for aluminium and car recycling will be given as well as a dynamical system model that describes the interconnected material flows for Ag, Au, Bi, Cu, Fe, Ni, Pb, PGM, Sn and Zn for a study on lead-free solder.

Jan 1, 2003

By Bhargav Dhavala, Sristy Raj, Ashok Kumar, Suman Krishna Sit, Adity Ganguly, D. P. Chakraborty

"Tatasteel’s West Bokaro washery#3 is designed to deslime raw coal at 0.5mm; the oversize (+0.5mm) is beneficiated in dense media cyclones (DMC) while the undersize (-0.5mm) is beneficiated in froth flotation (FF) cells. Nearly, 80% of the raw coal feed reports to the DMC circuit consisting of four parallel streams. Presently, the performance of DMCs at washery#3 is interpreted by: (a) comparing the actual plant yield w.r.t the lab predicted yield and (b) misplacement of clean coal to middllings.However, the comparison between actual & lab predicted yield is fallacious given the fact that the lab predicts yield of the borehole sample while the feed received at the plant has different characteristics altogether due to the dilution during mining. To mitigate the said limitations, a quick diagnosis tool using the past data has been developed that will give a prediction of performance of different coal seams in the DMCs, inputs being feed ash to DMCs and stream wise feed specific gravity (coal & magnetite combined).The tool also will help in identifying the root cause on real time basis thereby helping the operator to take necessary corrective actions. The operator can intimate the mining personnel in cases of shale reporting to the feed as a result of dilution during mining. In events of higher standard deviations between the parallel streams w.r.t feed specific gravity, the operator can adjust the parameters accordingly to minimize the yield loss. INTRODUCTION West Bokaro came into existence in 1948, as an independent coal company, managed by M/S Anderson Wright. Tata Steel acquired the Company in 1956 to meet its requirement of metallurgical grade coal for Iron making. Subsequently, in 1976, it was made a division of Tata Steel. In 1974, when coal mines were nationalized, West Bokaro was exempted as it produced coal only for captive consumption of the Steel Works. The first washery of India was set up in West Bokaro. The business objective of the West Bokaro division is to produce clean coal at optimum cost for captive use in the steel plant of Tata Steel at Jamshedpur. The strategy is to reduce ash with minimum loss of yield so that quality of coal improves and yet the cost is beneficial vis-a vis imported coal. The primary product is the metallurgical grade coal for coke ovens, which converts coal into coke for use in the Blast Furnaces."

Jan 1, 2018

By Claudio L. Schneider, Peter R. King, Reiner Neumann

"Predicting the liberation spectra that are produced from breakage of two-phase ores under the random fracture assumption can be accomplished by measuring the conditional, on length, linear grade distribution directly from images obtained from a representative sample of the unbroken texture. The technique tremendously simplifies the prediction problem by avoiding the multiple convolutions that arise from the traditional method based on a description of texture from a measurement of the chord length distributions associated with each phase in the unbroken texture. For a 3-phase system, the phase transition probabilities associated with the textural information make the traditional calculation an almost insurmountable mathematical problem. The direct measurement procedure on the other hand can be expanded to three phases comparatively easily.A coal sample is used here to demonstrate the procedure. It is concluded that the conditional, on length, linear grade distribution can be predicted in the same fashion for multi-phase systems. Accurate stereological conversion is the practical hurdle to be overcome for multi-phase systems, but it is already a reality for 3- phase systems."

Jan 1, 2003

By John Nell, Paul den Hoed

Carbochlorination tests were conducted with matched particle-size fractions of rutile, ilmenite and high-titania slag in a small bubbling fluidized-bed reactor. The effects of temperature, the type and proportion of solid reductant in the charge, and the fraction of Cl2 in the fluidizing gas were investigated. Tests confirm the need for solid carbon in the bed if chlorination is to run at high rates. With solid carbon in the bed, CO supplied with the fluidizing gas does not increase significantly the degree of chlorination after 75 minutes. Ilmenite is chlorinated more quickly than titania slag, which in turn is chlorinated more quickly than rutile. Rates of chlorination at 1100°C and 1000°C are much the same and significantly higher than at 900°C. Chlorination is associated with significant increases in particle porosity (even for rutile), which is brought about by the rapid initial chlorination of FeO and MnO (in ilmenite and slag) and (it is argued) by the chlorination of Ti2O3 which forms at high-energy surface sites. A reaction mechanism is presented; where possible, its validity is demonstrated by the support of empirical observations.

Jan 1, 2003

By F. A. V. Guimarães, A. M. Costa

"The moisture in sintering is a very important parameter for the performance of the process. It allows that the granulation takes pace in an efficient way making the water bridges between the bigger particles used as nucleus and the finer particles that perform the coating of those coarse particles. The formation of the micro pellets is extremely important to prevent loss in permeability of the bed in the sintering grate, avoiding excessive fuel consumption and producing a quality sinter. The aim of this project is to use some of the methodologies for determine the saturation degree on ores and coal to determine the optimal moisture for sintering. In the sinter pot grate series, 3 to 4 assays in a series of 10 are required to determine the optimal moisture for the process. The saturation degree curve test has shown that is really viable to use this technique to skip those tests and go directly to the series to determine productivity and the coke / anthracite consumption. In an industrial scale can be used to adjust the water addition in the conventional mixing methods used in the sintering plants to increase productivity in the process.INTRODUCTION Sintering Sintering is a high temperature agglomeration process in which iron ore fines are partially melted and bonded together using fluxes and a source of fuel, usually coke breeze. The agglomerated product, sinter, has improved metallurgical properties making it an ideal ferrous burden that enable the passage of hot gases in the iron-making blast furnace. The sintering process is normally carried out over three basic stages: granulation, ignition/sintering, and product sizing. In the granulation stage, iron ore fines (usually a blend of selected ores), sinter return fines, fluxes and fuel, and are mixed with water and micro-pelletised in a drum or disc before being introduced in the main granulation circuit. (Wang, Teng, & Wang, 2017)."

Jan 1, 2018

By J. Zou

With the increasing applications of the Chinese metal magnetic liners, the requirement for their technical specifications has become stricter and stricter. It is necessary to deeply analyse the metal magnetic liners in order to improve their reliability and economics. The key issue of metal magnetic liners is magnetic forces: their attractions to mill shell and protection layer. Mathematical models were developed using finite-element analysis software and systematic simulation analyses of the two most critical indexes of magnetic liners were performed to find out the most important parameters and their effect on the liner?s characteristics. The relationships between magnetic forces and installation gaps, thickness of permanent magnets and thickness of protection layer may be used to guide the design of metal magnetic liners for ball mills in order to achieve good economic indexes.

Jan 1, 2014

By H. Deng

Oxidized zinc ores are the main source of zinc metal except sulfides. To have a better understanding about the performance of smithsonite and the main gangue, quartz, in flotation, the aggregation behaviors of smithsonite and quartz in water were confirmed by different techniques (sedimentation tests and optical microscopy). The experimental results show that smithsonite and quartz particles aggregate in the pH range 7.5-11. The results of zeta potential suggest that the aggregation does not correlate with the DLVO theory, when the iso-electric point of smithsonite and quartz is 8.0 and 2 respectively. When the solution pH is less than 8.0, smithsonite has an opposite charge to the quartz particles. Electrostatic adsorption makes effort on these two kinds of particles according to DLVO theory. Whereas, solution chemistry calculation shows the pH range 8-11 corresponds to hydroxide formation, suggesting that this is the species responsible for aggregation. And their concentrations are much higher in sodium hydroxide system than that in sodium carbonate system. Aggregation of smithsonite and quartz due to the flocculation action of zinc hydroxide is proposed.

Sep 1, 2012

By V. V. Morozov, Ganbaatar Zorigt, Delgerbat Lodoy, Y. P. Morozov

"At the processing plant Erdenet, a new facility for advanced ore diagnostics in-stream (at the conveyor), based on optical analyser of mineral composition, was tested. Such systems provide highly accurate in-stream measurements of ore properties. The system provided information on the ore mineralogical composition, the particle size distribution and the impregnation of minerals. A special flatbed facility for optical spectrum-based estimation of fine-crushed ore has been developed, being incorporated into the existing system of ore sampling and analysis. Application of the flatbed facility renders possible a high accuracy of determining ore mineralogical composition. High precision of the optical spectrum-based estimation is achieved using special devices, installed in the sampling and the sample analysis flow sheet, applied by the technical control department. Modern systems for optical spectrum-based estimation of ore grade provide a basis for effective automated control of ore benefication processes, based on the principle of advanced ore grade control. Process management task of grinding and flotation was to choose options that take into account the composition and grade of the ore coming. The calculation data array comprises consumption of reagents, ore processing, grind size etc. The systems implemented at the processing plant contributed to increasing copper and molybdenum recovery. INTRODUCTION In-stream ore grade analysis is a new trend in effective control of ore benefication processes. This is realised based on radiometric measurements in the X-ray and visible spectrum regions, in which mineral components of the initial ore (Sbárbaro and Villar, 2010) or the benefication products become apparent (Hyotyniemi and Ylinen, 1998; Haavisto and Hyötyniemi, 2010). An important advantage of such methods is in-stream measuring ore parameters, including mass fractions of individual minerals, which makes it possible to use the information obtained in the processes of automated control."

Jan 1, 2018

By Jihoe Kwon, Daeyang Lee, Mario Fujimura-Kashiwagui, Heechan Cho

"Calcium carbonate is one of the most widely used mineral in today&apos;s industries such as plastic, paper and pigment. There are many essential physicochemical properties required by each industry field but the most common requisite is size. One way to achieve appropriate size is grinding. Grinding is typically an energy intensive process, consuming about 40% of total energy cost in mineral process. Due to that reason, optimization of grinding process is a critical element to achieve price competitiveness. Two different type of grinding apparatus were hired to find out optimum condition in terms of energy efficiency. Utilizing samples containing 10, 20, 30 and 40% solids concentrations, a 1l batch type attrition mill was operated as the first grinding step at various operating speed with 1? to 5? grinding media in order to study the optimum operating conditions to reach submicron particles. Next, a 0.15l vertical beads mill was tested as next step with 100? to 500? grinding media to study the optimum conditions in the submicron range. Net energy and the specific energy input was measured to reach stated size ranges. Also, using a back-calculation based on the population balance model further operating conditions were studied. There were several competitive combinations which showed significant energy efficiency improvement when compared with the single step grinding."

Jan 1, 2014

By N. J. Bolin

The Aitik copper mine is located in the north of Sweden and the concentrator at the mine started its operation in 1968 with a capacity of 2 Mton ore per year. Since then the operation has expanded several times, and today the capacity is 18 Mton ore per year. A new expansion plan was investigated in 2005, however the building of a new concentrator was found to be a better solution, giving a lower cost, a longer lifetime and more concentrates to the smelter at the coast. Several choices have been evaluated regarding the location of the concentrator?s crushing, grinding, dewatering, process control and water systems. The energy cost comparison has been an important factor when evaluating the various choices. The single most important decision has been in choosing the grinding system. Once again the fully autogenous grinding system, favoured by Boliden, has proven to be the best solution. The location of the mill, high and near the tailing pond, gives lower transportation costs for the ore and tailings, compared to other locations. A new water system will lower the pumping cost, give better control of water circulation to the plant and create fewer problems with permafrost in the tailings disposal area. Molybdenum recovery will be installed in the new plant using a separate circuit. A gold leaching plant was also investigated. Gold leaching is planned for the pyrite concentrate from the chalcopyrite/pyrite separation and the concentrate from the desulphurisation circuit that will be installed on the bulk flotation tailings.

Jan 1, 2014

By Rong Fan, Andrea Gerson

"The small recovery of Ag, often in the order of 50%, by traditional flotation and leaching process strategies is closely related to the complicated and heterogeneous nature of Ag-bearing minerals with Ag typically being associated with numerous minerals within any given ore-body. Moreover, grain sizes may be extremely fine with micron-scale common. In order to design cost-effective Ag-bearing mineral flotation and leach recovery strategies it is firstly necessary to characterise the speciation of Ag and its correlation with other elements, e.g., Cu, As and Sb, within the ore matrix and process streams. The traditional QEM-SCAN analytical approach can prove problematic for some mineralogies due to difficulties in recognising degrees of crystallinity, polymorphs, complex solid solution series, high value trace element mineralogy, very fine grained materials; and the requirement for a comprehensive data base. Moreover, there is difficulty ‘seeing’ either surface films or surface contaminants which can both lead to poor flotation performance. There is therefore clearly a need to develop confirmatory and complementary approaches when these uncertainties arise. Synchrotron X-ray microprobe analysis provides a powerful tool for the mineralogical characterisation of finely segregated heterogeneous Ag-containing materials. These measurements enable comprehensive characterisation of the Ag-bearing components using synchrotron microprobe X-ray fluorescence mapping (µ-XFM), X-ray diffraction (µ-XRD) and X-ray absorption spectroscopy (µ-XAS). Further analytical strength is provided by principal component analysis of laboratory ToF-SIMS data which enables the statistical identification of correlated surface species enabling examination of surface chemical characteristics responsible for mis-reporting of Ag containing components within flotation streams. We describe the application of these techniques to a selected Ag-containing feed and tail and demonstrate how these compliment and extend traditional analytical methodologies."

Jan 1, 2014

By P. Spolaore

In the frame of Bioshale FP6 project, the bioprocessing of a polymetallic and polymineral concentrate produced in an industrial operation in Lubin, Poland, was assessed. Following successful batch culture tests, processing in continuous conditions was tested to determine the main specifications for the application of the stirred-tank technology to this sulphide concentrate from black shale ores. The experimental work was carried out in a laboratory-scale unit consisting of 3 stirred tanks (50L or 20L) using an acidophilic and moderate thermophilic bacterial population. Different configurations of the unit and key operating parameters were tested (nutrient medium composition, solids concentration, rates of agitation and aeration). Scientific and technical approaches, such as bacterial community structure and mineralogical analysis were implemented in order to better understand the chemical and biochemical reactions occurring in the system. Using the data produced during the continuous operation, downstream processing assessment for both copper and silver recovery was also carried out. The best copper recovery obtained in the continuous operation was 92% and a hot brine leaching of the bioleach residue (PLINT process) allowed to recover 92% of the silver. A preliminary tech-no-economic evaluation of Lubin concentrate bioprocessing including bioleaching, copper and silver recoveries demonstrated the potential economic feasibility. Recovery of silver plays an important role in the economy of the process. This study presents promising values to further investigate this bioprocessing option.

Jan 1, 2014

By P. Condori

In spite of the importance of the slurry transport and discharge in autogenous and semiautogen-ous (AG/SAG) mills, it is evident that a more comprehensive and useful model is still required. Semi-empirical models used up to now have many limitations and cannot be used beyond the ranges in which they were developed. The breakage of particles as they are transported along a mill com-plicates the experimental analysis and the modelling of the transport process within the mill. The interaction of the grate discharge and the pulp lifters, with the added issue of backflow from the pulp chamber into the mill, makes the discharge modelling process difficult. In order to overcome these difficulties, a mechanistic approach has been applied. The general transport and discharge model was subdivided into four independent models: Flow through the charge, flow through the grate, flow in the pulp lifter, and flow-back. This paper gives an overall description of the modelling approach and discusses in particular the modelling of transport of fluids through the charge. In order to evaluate and calibrate the model, experimental work was carried out. To evaluate the gradient pressure under different conditions of charge packing and flow rate, a specialised experimental rig with a highly sensitive pressure gauge was used. Preliminary results identify the differences of the charge and grate on the restriction of flow. The existence of a dynamic voidage in our particular system was more evident and as a result, a semi-empirical correlation for the voidage was developed. In general, results show that the me-chanistic model derived from Ergun?s equation for flow through a packed bed can be satisfactorily adapted.

Jan 1, 2014

By L. Filippov

"Nickel is an important metal with the total global consumption of about 2 million tons per year. It is sourced from both sulfide and laterite ore, but currently laterites are becoming more attractive for nickel production due to the depletion of high grade nickel sulfide ores. Laterites are generally processed by hydro or pyro-metallurgy and therefore, pre-concentration of nickel before such processes is very important. In this paper the effect different physical methods (including flotation) on the pre-concentration of nickel in laterite ores will be discussed. The ore used in this study was a laterite from South East Asia. Nickel was upgraded using different methods such as magnetic separation, flotation and sizing. The effect of ore mineralogy on choosing the best strategy to upgrade nickel will be discussed. The findings of this project will help to unlock a substantial volume of nickel with significant value from laterite ores.INTRODUCTION Nickel is an important metal with the total global consumption of about million tons per year which has grown rapidly during last decades (Mackey, 2011). Nickel is sourced from two different types of ores, sulfide and laterite. The majority (about 70%) of the world’s nickel resources occur as laterite ores which are often complex, and low grade, and therefore expensive to treat using conventional methods (Xu et al., 2013). Today, nickel laterites are more attractive for production of nickel as the amount of high grade nickel sulfide ores has diminished (Janwong, 2012). Therefore more economic processes to recover nickel from these resources should be developed.It should be noted that nickel laterite mineralogy is complex, and nickel often presents as ultrafine inclusions in a number of mineral phases. Because of the low nickel concentration and variable distribution in these phases, effective upgrading by physical separation processes would be challenging. Researchers have tried to improve nickel laterite flotation recovery by using a number of feed preparation techniques. A summary of the nickel grades obtained using flotation and magnetic separation as reported in the literature is presented in Table 1. It can be seen that only minor nickel upgrades have been reported. Quast et al. (2015) have concluded that the complex mineralogy of nickel laterite ores makes it difficult to achieve any significant nickel upgrading by physical techniques, including flotation. They achieved 40% increase in the nickel content (from 1.0% to 1.4%) at a nickel recovery of 43% (Quast et al., 2015). Various attempts in USA, New Caledonia, India and Australia, to upgrade nickel in laterite using magnetic separation have not been successful (Quast et al., 2015). A recent comprehensive review on topics influencing nickel laterite flotation has shown that further investigations in the flotation of laterite ores are undoubtedly warranted (Farrokhpay & Filippov, 2016)."

Jan 1, 2018