Search Documents

By S. Q. Zhu

A newly developed coal flotation collector ZFC and its flotation characteristics for five different coals were introduced in this paper. ZFC is an emulsion composed of 27% diesel oil, 70% water and 3% surfactants. The main surfactant is synthesized with oil which is environmental favorable and reproducible. Compared flotation experiments show that, at the same dosage, ZFC give 2%~5% recovery promotion than typical collector with only a slightly ash content increment, but saving 70% diesel oil. Zeta-potential and Wetting heat measurement indicate that the surfactant helps the interactions between oil and coal particles, the industrial application tests in several coal preparation plants demonstrate that ZFC is suitable both in technical and economical aspects.

Jan 1, 2014

By Priyanka Dhar, Kurt Aasly, Hanumantha Rao Kota, Hassan Bouzahzah, Maria Thornhill

The interest in investigating the processing characteristics of mineral deposits in Norway has seen an upsurge in the last decade. One of the major areas of interest is a huge copper deposit, operated by NUSSIR ASA located in the Repparfjord Tectonic Window in the caledonides of west Finnmark. This study reports analysis of ore from the deposit for development and modifications in the flotation flowsheet for the NUSSIR ASA copper ore. The mineralogical characterization for the ore sample was achived by optical microscopy and Zeiss automated mineralogy while grinding characteristics were tested using Bond Index tests. The results confirmed the presence of Cu minerals in the form of chalcocite, chalcopyrite and bornite in the samples, which are mainly liberated in the – 105 µm size range. The majority of non-liberated copper sulphides associated with silica and the carbonates varies from 3 to 28 percent in the –250 µm samples . It is also observed that the copper minerals are uniformly distributed in all size ranges. Selective flotation of NUSSIR copper ore was performed in different size fractions with a motive to identify the correct liberation size and thus to obtain a copper concentrate meeting the quality requirements. The flotation experiments are essentially performed in two stages: the rougher and the cleaner stage. Mass balance calculations were performed showing that approximately 88 percent of copper can be obtained at the end of the process. Ultimately, overall circuit copper recoveries ranged between 83.5 to 88.1 % with a concentrate grade of 35 to 48 % Cu.

Jan 1, 2018

By Güven Önal, Gülay Bulut, Mustafa Özer, Yunus Emre Benkli, Olgaç Kangal, Mustafa Tarkan

There are various types of natural zeolite deposits in Turkey. Naturally occurring zeolites are excluded from many important commercial applications where uniformity and purity are essential. In this paper, the beneficiation of natural zeolite, taken from western part of Turkey, was investigated. According to X-Ray Diffraction (XRD) and mineralogical studies carried out on the representative ore sample, the natural zeolite was found to be in the forms of clinoptilolite and heulandite. Clinoptilolite forms as a devitrification product of volcanic glass in tuffs. Quartz, clay minerals, orthoclase, plagioclase, biotite, seruzite-muskovite and epidote were observed as impurities. Several types of mineral processing methods were performed in order to remove impurities from the natural zeolite sample to produce high purity zeolite. Gravity separation methods such as shaking table and superpanner were carried out for separating heavy minerals, while high intensity dry magnetic separation was used for discarding magnetic minerals.

Jan 1, 2003

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By I. N. Gridasov, T. V. Ignatova, E. V. Shelepov

"Mikhailovskoye Deposit is comprised of oxidized ferruginous quartzites among other minerals with the former widely spread across the ore field and mined along with unoxidized ferruginous quartzites. PJSC Mikhailovsky GOK strategic development is aimed at iron ore product output expansion. The most critical item of the strategic development road map is process design for separation and concentration of hematite contained in oxidized ferruginous quartzites mined as the by-product in the open pit. Laboratory and semi-industrial tests run to design cost-effective, reliable and environmentally friendly process for Mikhailovskoye deposit oxide quartzites processing included the following processes: - pilot tests of reverse anionic flotation which produced concentrate with Fe60.1-62.9% total iron content and 66-69%Fe recovery rate; - combined magnetic separation and flotation (Marubeni Company, 1982) including slime removal, reverse anionic and cationic flotation and high gradient magnetic separation resulting in 48.9% yield, Fe55-57.5%, up to Fe60.5% hematite concentration ( Fe64.1% being the best result achieved),76.2% recovery. - magnetic separation and flotation, including separation in low gradient (1400 Oe) and high gradient (up to 17000-18000 Oe) magnetic field. The results of these pilots tests were the following: 57-59%Fe concentrate, 70%Fe recovery (Mekhanobrchermet, MGOK, 1982-1988): - magnetic roasting in pilot plant of TSGOK (Krivoy Rog) which produced 61.1%Fe concentrate with 81.5% recovery. Major disadvantage of the method is high generation of dust equal to 20% of the initial feed. Based on third-party studies flotation of oxidized ferruginous quartzites process embracing best processing methods was designed by Metalloinvest Management Company LLC and PJSC Mikhailovsky GOK engineers. This paper discusses analysis of studies aimed at intensification of separation processes with application of mechanical slurry agitation (MSA), addition of alkali (NaOH) and elutriation of initial feed. The paper also provides a design solution to implement a lab-scale MSA plant. It includes feasibility evaluation of MSA inclusion in flotation of oxidized ferruginous quartzites process to enable higher yield and hematite recovery in resultant concentrate. Outcomes of the discussed work have significant value for prospective engineering of OFQ concentration process."

Jan 1, 2018

By Edgar Schach, Tom Leistner, Markus Buchmann, Urs A. Peuker, Martin Rudolph, Marius Kern

"In this study, the flotation characteristics of a cassiterite-bearing fine-grained and complex skarn ore from a deposit in the Ore Mountains is investigated. The tests are performed using an oil-assisted column flotation approach to process very fine ore fractions and avoid losses of cassiterite into the tailings. First, process parameters are obtained for a finely ground artificial mixture of quartz, magnetite and cassiterite, simulating the real ore. Thereby, magnetite is used, as iron oxides can have a detrimental effect on the flotation due to a similar flotation behavior. In addition, they can act as a source of multivalent ions, which are known to reduce the concentration of collector molecules, active for flotation. Based on the results, selected parameters are further tested for cassiterite skarn ore from the Hämmerlein deposit including a pre-conditioning and a water exchange step to remove ionic contaminants. The process response is analyzed in detail by XRF (X-ray fluorescence) and MLA (mineral liberation analysis) to get a better understanding of the behavior of the single ore components. Sulfosuccinamate type surfactant is utilized as the collector, emulsifier and to reduce the froth destabilization through nonpolar oil. Sodium hexafluorosilicate is added as the depressant.INTRODUCTION Complex skarn ore deposits containing considerable amounts of tin, indium and other metals are located in the Ore Mountains region (Germany). In this study, a skarn ore from the Hämmerlein deposit was investigated. Due to the finely disseminated nature of this ore, past beneficiation attempts failed, and the ore was considered economically unprocessable. However, increasing resource demands brings it back into focus (Schuppan and Hiller, 2012). Cassiterite is the main tin bearing mineral in this ore. Due to its high density (~7 g/cm³), the predominant beneficiation technique is gravity separation (Angadi et al., 2015). Tin ores from disseminated deposits have to be extensively comminuted to reach a sufficient degree of liberation of the cassiterite grains. As cassiterite has a brittle nature, it is preferable enriched in small size fractions, during comminution (Angadi et al., 2015). Gravity separation methods become more and more inefficient for particles smaller 40 µm (Falcon, 1982), causing tin losses of up to 30 to 40wt.-% (Angadi et al., 2015). Thus, froth flotation of cassiterite was first utilized in Altenberg in the Ore Mountains as an additional processing step to reduce the cassiterite losses into gravity separation tailings (Bulatovic, 2010; Gruner and Bilsing, 1992). Although the reported lower size limits for an effective cassiterite floatability are often smaller compared to other minerals, the flotation performance is in general decreasing for small particle sizes < 10 µm (Trahar and Warren, 1976). Therefore, different approaches have been already investigated for the flotation of such fine cassiterite fractions to overcome the limits in particle size. Bilgen et al. investigated the shear flocculation of cassiterite with a sulfosuccinamate collector (Bilgen et al., 1994). The agglomeration flotation of cassiterite has been tested by Schubert et al. (Schubert et al., 1966), in which the selective coagulation of fine hydrophobic particles and oil droplets leads to an increase of the effective particle size. Recently, Leistner at al. investigated an oil-assisted agglomeration flotation for ultra-fine cassiterite ore fractions (Leistner et al., 2016). However, a poor response due to an increased concentration of Fe and Ca ions, unselective oil/gangue coagulation and froth instability, that is caused by oil/frother interactions, has been observed."

Jan 1, 2018

By I. S. M. K. Ilankoon

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behavior is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. Previous modeling of this system has used equations from oil and ground water flow to model these systems, but the applicability of these models with the larger particles found in typical heaps is suspect as these systems are not necessarily capillary dominated. In particular, as the characteristic particle size goes from below to above a few centimeters, the flow changes from capillary to gravity dominated. This means that typical heap leaching heaps cover this interesting, but complex, transitional fluid flow regime. In this paper a set of experimental studies of this flow, including PEPT (positron emission particle tracking) based tracer experiments, highly accurate liquid holdup measurements and axial dispersion experiments using salt tracers will be presented. In this study, flow through mono-dispersed particle beds was carried out. In particular, the hysteresis in the liquid holdup as the liquid flow rate into the particle bed is varied is investigated, since this hysteresis means that the relationship between flow rate and holdup is history dependent, an effect not included in models currently used to describe fluid flow in heaps. A theoretical model that describes this hysteresis will also be presented. Keywords: heap leaching, hydrometallurgy, modeling

Sep 1, 2012

By N. D. Ilankoon

"The use of thiosulfate as an alternative lixiviant for cyanide to treat complex refractory ores followed by the use of ion exchange resins (IX resins) for gold recovery has become an industrial reality. In this study, polyethylenimine (PEI) coated iron oxide magnetic nanoparticles (MNPs) were used to recover gold from the leaching solutions that consist of calcium thiosulfate, copper and gold. The gold loaded MNPs were easily separated from the solution using an external magnetic field. Proposing a novel adsorbent with characteristically easy solid-liquid separation, to recover gold from synthetic thiosulfate leaching solutions and gold elution and reuse of MNPs were the main objectives of this study. Adsorption isotherm studies revealed that the data fitted both Langmuir and Freundlich isotherm models equally well. The maximum adsorption capacity was 18.5 mg/g at pH 8 and 50?C. According to thermodynamic studies the physisorption process was exothermic and spontaneous. Gold and copper elution, and the regeneration and reuse of the nanoparticles were investigated and promising results were obtained. Different elution systems comprising sulfites, chlorides, glycine, EDTA (ethylenediaminetetraacetic acid) and sodium hydroxide were considered. Among them, EDTA for copper elution and NaOH for gold elution were the most efficient eluants. Regeneration and reuse studies revealed that the MNPs can be used for several cycles without significant performance loss. INTRODUCTION Although cyanidation has been used for gold leaching for more than 100 years, some major drawbacks associated with cyanidation have led to a quest for alternative lixiviants for gold leaching. Cyanide is ineffective in treating carbonaceous refractory ores as gold cyanide complex is adsorbed onto the native carbon in the ore itself known as preg-robbing. On the other hand environmental concerns associated with cyanidation drives the need for environmental friendly alternatives for cyanide. As of today, thiosulfate is known to be the most extensively studied and most promising alternative lixiviant for cyanide in both technical and environmental perspectives (Aylmore and Muir 2001, Oraby 2009)."

Jan 1, 2018

By F. Z. Dong

The paper is mainly about a study on the techniques of separating iron from pyrite cinder of a certain sulfuric acid plant in Shandong province. The main components of the cinder are Fe2O3 and SiO2, and the degree of liberation of iron mineral and gangue is very high. So the iron concentrate with higher degree of iron and lower grade of silicon and sulfur can be achieved by reverse flotation. The iron grade of the concentrate reaches 63% and the recovery of iron is no less than 63%. And the most important influencing factor of the flotation is the temperature of the pulp. A better guideline can be achieved by magnetic separation. The cinder is magnetizing roasted for 15 minutes with temperature of 800?, and the concentrate with the iron grade 64%, sulfur grade 0.2% and iron recovery 85% can be obtained by two stage magnetic separation. A rotary kiln has been built to deal with the pyrite cinder, and the result of the industrial magnetizing experiment and magnetic separation is satisfying.

Jan 1, 2014

By R. C. Miranda

Flotation is an operation widely used in mineral processing because of its aptitude to recover minerals of interest very efficiently. Flotation is often responsible for making possible the exploitation of mineral deposits of low concentration. In flotation various processes phenomena occur, some of which have still not been explained scientifically. Due to this fact, there are no models that can be widely applied in flotation control. Thus, in most cases, the control is done by experienced operators who are able to visually classify the types of foam into different categories and each one of them is associated with an operating actuation. In this situation, image analysis is configured as a solution that has already been employed in several ways. In this paper, a control strategy based on the colour of froth on a direct flotation of a nonferrous metal is presented. Moreover, the paper reveals the theoretical basis of the method, the critical points, difficulties and improvements that can be implemented. Data of grade were collected from the mineral of interest and RGB (red, green and blue) data of final concentrate of the froth. The mineral grade was collected and analysed during one month of operation and RGB was obtained using a camera. It was verified that the red colour showed the same trend of the grade curve in the concentrate. Thus, the use of this online data in optimising control was introduced. The laboratory grade is used to calibrate the colour set point. Therefore, it was possible to monitor in real time the trend of enrichment and depletion of a non-ferrous mineral in a flotation. It was possible to establish an online control strategy based on simple data acquisition. The result was an increase of 10% on production.

Sep 1, 2012

By Leming Ou, Hongqiang Li, Li Zeng, Qiming Feng, Yiping Lu, Guofan Zhang

"The entrainment of sericite, especially in the presence of hydrophobic microcrystalline graphite, leads to the poor flotation selectivity of microcrystalline graphite ore. In this paper, it was attempted to reduce entrainment of sericite, selective flocculation of microcrystalline graphite using polyethylene oxide (PEO) was studied. For the sake of flocculate microcrystalline graphiteselectively, flocculation tests of microcrystalline graphite and sericite single mineral were conducted.To investigate the effect of selectiveflocculation of graphite on entrainment of sericite in microcrystalline graphite flotation, batch flotation tests of graphite single mineral and artificial mixtures were conducted; theflocculationselectivity of PEO of different molecular weight (M.W.) was alsocompared inartificial mixture flotation. Inthe end, the structure of flocs in different particle size was studied by sieve analysis and microscopic observation. The resultsindicated that PEO of molecular weightone million andtwo million could selectivelyflocculate the microcrystalline graphite and reduce the entrainment of sericite at a lower dosage; further increasingof the dosage of PEO(M.W. ?two million) led to hetero-flocculation between graphite and sericiteandmadethe ash content of concentrate increase again."

Jan 1, 2014

By Y. Foucaud, C. Eswaraiah, L. Filippov

Enhanced gravity separators such as Falcon concentrator which uses additional centrifugal force, are the most common gravity concentration techniques used for fine particles processing. Hence, understanding the kinetics and separation mechanisms within these separators is of paramount interest. Recent research yielded a predictive physical model for the Falcon Ultra Fine (UF) which however does not explain some results obtained with industrial ores. This study aims to identify the mechanisms involved in Falcon UF separation with the objective of confirming or rejecting the hypotheses on which the current model is built and suggesting potential points of improvement. The Falcon UF kinetics is investigated through the processing of complex low-grade and fine-grained ores from the Altenberg tin deposit (Germany), the Tabuaço tungsten deposit (Portugal) as well as a synthetic iron ore. Saturation tests are performed on the Falcon UF by controlling the separation efficiency in terms of recovery and enrichment ratio with time or feed mass. Results show an evolution of Falcon UF performance with time in contradiction with the stationary separation hypothesis on which the physical model is based. Observation of the concentrate bed suggests the presence of erosion figures in furrows which may play locally an active role in the separation. In terms of Falcon UF separation timing, three phases can be distinguished. First, upon initial feeding of the bowl, a bed quickly grows unselectively and ultra-fine particles are ejected from the bowl until the bed reaches its final profile. Next, actual separation occurs with selective concentration of dense particles. Finally, capture sites saturate and recovery drops. The evolution of partition curves over time confirms the existence of two separation mechanisms. First, differential particles settling within the flowing film responsible for the ejection of small size particles during the whole separation cycle which is already accounted for in the physical model. The second mechanism involved may be explained by the action of lift force, neglected in the physical model, which acts preferentially on coarse particles deposited at the surface of the bed resulting in coarser particles being rejected in the tailings. Hence, the addition of a lift force component to the existing model is suggested to account for this second separation mechanism.

Jan 1, 2018

By Fengnian Shi

In the current energy-sensitive world, sustainable development in the mineral industry will require new, better and more efficient processes. Novel comminution methods, which offer the prospect of achieving the required outcomes of size reduction and mineral liberation at lower energy consumption, are continually being sought. In the past five years, extensive research using high voltage pulse electrical comminution technology has been carried out at the Julius Kruttschnitt Mineral Research Centre (JKMRC), in collaboration with selFrag AG. The major outcome of this research is the development of the concept of pre-weakening ore particles by electrical comminution procedures to reduce the energy consumption in the downstream grinding circuit. The research has also verified the preferential liberation of valuable minerals by electrical comminution. Given the advantages, several potential applications of electrical comminution in the mineral industry are proposed, including AG/SAG mill feed pre-weakening, pebble treatment, ball mill feed pre-weakening, early recovery of the liberated valuable minerals, crack/micro crack generation for improved leaching, and smelter slag treatment. For the mineral industry to utilize electrical comminution, two emerging issues identified from the research need to be address. They are the energy consumption by electrical comminution in the locked cycle treatment and the facilities scale up necessary to move this technology from the laboratory to the plant. Keywords: high voltage pulses, electrical comminution, energy efficiency, mineral liberation

Sep 1, 2012

By Willis Forsling, Prabhakar Swarna, Hanumantha Rao Kota

The solubility of wollastonite and its Hallimond flotation behavior as a function of dodecylamine concentration and pH are examined. The flotation response is characterized by adsorption and surface energy in the presence of amine. The methods of UV-Visible and FT-IR spectroscopy for adsorption and sessile-drop contact angle for surface energy estimation are employed. The results of wollastonite dissolution clearly showed its non uniform dissolution. The surfaces are depleted with calcium ions and became rich in silicon within 10 min of flotation time. Maximum flotation of wollastonite corresponds to a half monolayer coverage of amine, which is substantiated by the surface energy parameters. A good correlation between flotation, adsorption and surface energy as a function of amine concentration and pH was observed. The sudden increase in wollastonite flotation and amine adsorption at and above 5x10-5 M initial amine concentration is thought to be due to two-dimensional precipitation of amine on surface in accordance with the recent 2D-3D precipitation model of amine adsorption on silicate minerals.

Jan 1, 2003

By J. Drzymala

Ores and raw materials are subjected to mineral processing operations to increase the content of their useful components. Upgrading of these materials can proceed with different selectivity and therefore, there is a need to know and monitor the separation results of the process. The separation results can be evaluated using tables and graphs called upgrading curves. The course of lines in the upgrading curves is usually complex and depends on the graph type and process parameters. The Halbich grade vs. recovery plot is frequently used because is practical and it indicates several characteristic features of separation results. Separations by means of flotation of several different shale, dolomite and sandstone copper ores were performed along with determination of their mineral composition, copper content, liberation degree, and the maximum theoretical copper content in the first concentrate. These data, plotted as the Halbich upgrading curves, allowed to find other characteristic points such as practical maximum copper content in the first concentrate, maximum curvature coexisting with the liberation degree, maximum recovery of ore valuable components, and the slope the recovery-grade line at high recoveries as a measure of liberation. Correlations between theoretical and practical maximum copper contents in the first concentrate as well liberation degree and maximum curvature were also presented. They show that the ore type significantly influences the shape of the Halbich curve and its characteristic points.

Sep 1, 2012

By Dmitriy Makarov

The paper presents the modeling and analysis of oxidation of pyrite copper-zinc ore samples from the Letnee, Yaman-Kasy and Valentorskoye deposits. It is found, that the oxidized samples contain copper and zinc sulfates that are leached under the sample and water contact. It is shown, that sulfide floatability is decreased by the longer-term oxidation.We advise to improve nonferrous metals recovery by joint leaching and ultrasonic treatment of oxidized compounds. Study of the geotechnological processes of non-ferrous metal extraction, on the basis of two copper-zinc ore deposits shows, that heap leaching is of little use for the ores of the Letnee deposit. Leaching results for the Yaman-Kasy ore showed more promise.

Sep 1, 2012

This paper presents a theoretical investigation on the ionic equilibrium of Fe(III)?Ni(II)?H2SO4?H2O system. A non-ideal speciation model is developed to calculate the concentration distribution of iron and nickel species in a mixed ferric and nickel sulphate aqueous solution over the pH range from 0 to 4 and temperature from 25 to 100°C. A series of speciation diagrams for iron and nickel species is plotted with the effects of ionic strength and temperature on the equilibrium constants being taken into account. The ionic strength-dependent equilibrium constant is treated through a semi-empirical Vasil&apos;eV equation, which is based on an extended Debye?Hückel theory. A Helgeson model is applied to extrapolate the equilibrium constant to elevated temperature. The ionic equilibrium reactions are described by a group of numerical equations containing the temperature and ionic strength-dependent equilibrium constants, which are solved by the Newton-Raphson method. The speciation model is also applied to estimate the hydrogen ion activities and corresponding pH values. The calculated pH values are in agreement with the experimentally measured pH, and are compared to literature data and pH values produced by the Visual MINTEQ® program (a computer code for the calculation of chemical equilibrium in natural aqueous system). This investigation provides a deep insight into the ionic equilibrium behavior of a mixed metal sulphate aqueous system which commonly occurs in hydrometallurgical processing. Keywords: speciation, chemical modelling, thermodynamics, iron, nickel

Sep 1, 2012

By A. Koizhanova

Kumistinskoye gold- and silver bearing ores (Republic of Kazakhstan) as well as standardized test solutions containing gold, silver, copper, zinc and iron were studied. The best results in silver and gold recovery from Kumistinskoye gold- and silver bearing ores were achieved through use of complex cyanide-thiosulfate solutions as compared to individual cyanide solutions and thiosulfate solutions. It was found that such complex solutions substantially step up leaching process herewith increasing precious metals recovery rates. Thermodynamics of studied chemical processes was calculated. Reaction order, kinetic constant and activation energy of gold leaching process through use of cyanide-thiosulfate solutions were identified. We managed to prove that the sorption rates and holding capacity in process of gold anions recovery with anionite AM-2B are comparable to sorption characteristics for cyanide solutions. Keywords: gold, silver, copper, zinc, iron, cyanide-thiosulfate solutions, anionite AM-2B

Sep 1, 2012

By Wei Sun, Chengwei Li, Zhiyong Gao, Yuehua Hu

"Grinding for mineral liberation is a prerequisite for a successful flotation separation. Different grinding media produce mineral particles with different morphologies and surface properties. In this study, the surface physicochemical properties of fluorite particles produced by ball and rod mills were systematically investigated through single mineral flotation experiment, wettability measurement, X-ray diffraction (XRD) test and scanning electron microscopy (SEM) observations. The XRD observations reveal that the surface exposure degree for both mill particles follows the order {111} > {110} > {100}. The difference lies in that the rod mill ones have a higher exposure of more reactive {110} and {100} surfaces, leading to a stronger interaction with the collector. The difference also leads to their higher elongation and lower roundness values of rod mill particles which are beneficial for the particle-bubble attachment by shorting the induction time. The wettability and flotation results show that the rod mill ones have a lower critical surface tension and a greater hydrophobicity when treated with the collector solution and accordingly perform a higher flotation recovery. This work, for the first time, revealed the importance of the exposure of crystal surfaces in determine the shape factors and reactivity of the mineral particles and will help provide guidance for optimizing flotation separation and particle surface modification. INTRODUCTIONFluorite (CaF2) is the most important source mineral for producing F-based chemicals and materials which are widely used in industrial, environmental, and medical fields [1, 2]. In ore deposit, there are two kinds of occurrence forms of fluorite mineral. Firstly, the fluorite mainly coexisted with the gangue minerals like calcite (CaCO3) and quartz (SiO2). Because of their similar density and fine-grained dissemination in ore deposit, ball mill grinding before flotation separation has been widely applied to produce relatively fine particles [3]. Secondly, the fluorite is often associated with other valuable minerals with higher relative density such as scheelite (CaWO4) and cassiterite (SnO2). Due to their obvious density differences and coarsely grained distribution in ore deposit, rod mill grinding before gravity separation has been usually used to produce more uniform particles and avoid over-grinding [4-6]. After the gravity separation, a flotation separation is also employed to beneficiate the fluorite [7]."

Jan 1, 2018

By A. Gülmez

The complex ore deposit containing fluorite, barite and bastnaesite minerals is located in Beylikova Region of Sivrihisar town of Eskisehir Province of Turkey. The ore contains 40.80% CaF2; 35.35% BaSO4; 2.01%Ce; 1.5% La; 0.39% Nd and 0.1% Th. Barite recovery from this ore by flotation of the HCl leached tailings is presented in this paper. Rare earths are recovered by leaching. The leached residue (tailings) containing fluorite and barite is subjected to froth flotation to recover barite. The effect of pH and collector concentration on the flotation of barite have been studied in this work.

Sep 1, 2012