Search Documents

By S. M. Bradshaw, C. Dorfling, F. Ngandu

"Selenium removal and platinum group metal (PGM) recovery from copper sulfate leach solutions form an integral part of platinum producers’ base metal refinery operations. Recent studies found that substantially higher PGM recoveries can be achieved if excess thiourea instead of sulfurous acid is used as precipitation reagent; however, the impact of the proposed process on downstream processes was unknown. The objective of the current study was therefore to investigate the effects that excess thiourea and residual selenium present in the rich copper sulfate electrolyte have on copper electrowinning. This was achieved by performing cyclic voltammetry tests using a platinum rotating disk as working electrode, a graphite auxiliary electrode and a saturated calomel reference electrode. A synthetic copper sulfate electrolyte containing 0.01 M Cu2+, 1 M H2SO4 and varying amounts of selenium (20 – 150 mg/L) and thiourea (10 mg/L and 100 – 300 % excess) was used. The results obtained have shown that both thiourea and selenium interact with the cupric ion cathodic reduction reaction. Thiourea polarized the working electrode and lowered the efficiency of the cupric reduction reaction. Tests on the solutions with high selenium concentration showed simultaneous reduction of copper and selenium, which led to copper selenide formation. Nodule formation on the deposit surface also became significant at higher selenium concentrations. Based on these results, it was concluded that precipitation of PGMs from the copper sulfate solution with excess thiourea is not feasible due to the detrimental effect on downstream electrowinning operations.INTRODUCTION During the high pressure oxidative leaching stage in a typical base metal refinery (BMR) circuit, selenium, tellurium and some platinum group metals (PGMs) are dissolved along with the desired copper ions. The impurities (selenium and tellurium) may pass to the copper electrowinning circuit where it can result in the formation of nodular copper electrodeposits or reduced current efficiency. The presence of PGMs in solution, on the other hand, increases the precious metal inventory and potential losses of the operation. Currently, sulfurous acid is widely used for selenium and tellurium precipitation from copper sulfate leach solutions. Sulfurous acid is capable of reducing cupric ions to cuprous ions; the generated cuprous ions then react with Se4+ and Se6+ to precipitate selenium as a copper selenide (Bello, Dorfling, 2014). Recent studies have, however, proposed the use of excess thiourea as a precipitating agent for the removal of selenium and tellurium; it has the advantage of improved PGM recovery in the Se/Te precipitation step (Lottering, Eksteen et al., 2012; Mulwanda, Dorfling, 2015)."

Jan 1, 2018

By A. Morrison, D. Mesa, P. R. Brito-Parada

"Froth flotation is the most widely used mineral separation technique. It is based on the relative hydrophobicity of valuable and gangue particles. In a flotation tank, two distinct zones can be identified: the pulp and the froth. The pulp is a turbulent region in which hydrophobic valuable particles attach to air bubbles while hydrophilic gangue particles remain in the slurry. As the particle-laden bubbles rise, a mineralised froth zone is formed that overflows as a concentrate. Although the process is more than a hundred years old, there remain many aspects that are not completely understood, particularly for the froth zone. Thus, the rules governing the design of flotation tanks tend to focus on pulp zone parameters, which are largely based on operating data. An example of this is the design and operation of impellers. These tend to be designed paying attention to hydrodynamic phenomena in the pulp zone, but their effect on the froth zone has not been completely addressed. The role of impellers in a flotation tank is to break the air bubbles in order to generate smaller ones and to provide an environment that enables the collision between those bubbles and the particles in the slurry. This usually creates turbulent regimes that can affect the pulp-froth interface, destabilising the lower regions of the froth and affecting the overall performance of the process. Different impeller designs and retrofit modifications have been proposed in the past, addressing some of those issues. However, there is no systematic study of the effect of different impeller designs on the bubble size in the pulp and its links to the stability of the froth. This work tested the impact of an impeller designs combined with the use of a stator on the performance of an 87 litres continuously operated laboratory-scale flotation tank, with a focus on bubble size in the pulp and froth stability. The results showed that the implementation of a stator system decreased bubble size and increased froth stability. That resulted in an increase of mass pull, measured as a proxy of metallurgical recovery."

Jan 1, 2018

By Ashok M. Raichur, S. P. Vijayalakshmi

"Recent advances in technology and the growing environmental concern have laid emphasis on the usage of fine clean coal. Coal fines are also generated in large amounts during various coal processing operations and are difficult to be treated, handled and disposed. Since most of the operations use water as the carrying medium, the fines so generated contain lot of moisture. Conventional technique for processing coal fines includes flocculation by a polymeric reagent followed by moisture removal using a rotary drum or a pressure plate filter, which produce a product with more than 30% moisture. Polymeric flocculants though required in small amounts, need high shear mixing for good performance and operate only in a narrow pH range. Moreover they increase the viscosity of the solution by many folds. Hence it becomes imperative to emulate newer methods for efficient fine coal processing. One such method is the novel use of microorganisms in coal processing.The present investigation deals with the utilization of two gram-positive microorganisms, Mycobacterium phlei and Bacillus subtilis, as bio flocculants and dewatering aids in fine coal processing. Preliminary characterization done on J-coal and M.phlei showed that they are negatively charged over most of the pH range. B.subtilis was found to possess positive charge below pH 4.7. The adhesion studies proved the high potential of microorganisms for adsorption to surfaces. Adhesion tests were conducted at various experimental conditions by varying parameters like pH and ionic strength of the suspension. Results obtained showed that adhesion is always higher in the presence of an electrolyte like KNO3 and most of the adhesion takes place in 15 minutes. With change in pH the amount of B.subtilis adhering on to J-coal remained almost constant and for M.phlei it decreased at higher pH values. Increase in ionic strength did not increase the adhesion of bacteria. Flocculation experiments confirmed the ability of the bacteria to act as bio flocculants. It was seen that about 98% of the coal settled in about 2 minutes on the addition of bacteria along with the addition of the electrolyte. The electrolyte was found to be indispensable for efficient flocculation of the coal suspension and for the attainment of a clear supernatant after flocculation. Also the optical micrographs revealed the formation of large, tight flocs when the electrolyte is present along with the bacteria. Further, flocculation tests were done in the pH range of 2-10 and the flocculation efficiency was found to be independent of pH."

Jan 1, 2003

By G. A. Wierink

This paper discusses a new method to increase flotation recovery. As known from literature, fine and coarse particles have different flotation rate constants, hydrodynamic behaviour and require different reagent regimes. The device discussed allows separate processing of finer and coarser slurry by extraction of a third stream, carrying finer slurry, from the flotation cell. By separate treatment of fine and coarse slurry operational conditions and so flotation recovery for both may be optimized more efficiently. Extraction and classification of the third stream is accomplished by low speed centrifugation and Taylor-Couette flow separation. This Dual Outlet Device (DOD) can be installed in a traditional flotation cell without need for equipment replacement. In order to asses different design options for the DOD a transparent laboratory scale model was built. For this scale model Computational Fluid Dynamics (CFD) simulations using the RANS k-e and LES turbulence models were performed. Essential insight in the dominant flow systems relevant to optimal operation of the DOD was obtained from the CFD simulations and flow visualization tests with the laboratory scale model. Based on these findings a number of configurations were investigated at pilot plant scale in a 5 m3 Outokumpu flotation cell. The results of the pilot plant study show that utilization of the DOD provides a method for in-cell control over particle size distribution in the slurry. Use of the DOD in a flotation cell may enhance flotation recovery and decrease flotation reagent consumption significantly, against marginal investment and operation costs.

Jan 1, 2014

By Achilles Dutra, Everton Santos, José Oliveira

The beneficiation of phosphate ores by froth flotation is the most efficient process used to separate apatite from gangue minerals like calcite, dolomite and quartz. However, the similarity of surface properties between apatite and calcite generally lead to non-selective adsorption of reagents, rendering the selective separation of these minerals a worldwide problem. The phosphate deposit of Itataia, State of Ceará, Brazil, studied in the present work, presents a complex mineralogical composition having uranium associated with the apatite mineral. The main gangue minerals are calcite and quartz. The bulk flotation of apatite and calcite with anionic collectors in an alkaline medium followed by the selective flotation of calcite at pH 5.5 using phosphoric acid as well as citric acid as depressant have been suggested for this ore. This paper presents the results of contact angle measurements obtained using jojoba oil, a natural reagent composed mainly of gadoleic acid (C20:1) and long-chain fatty alcohols (eicosenol and docosenol), as an alternative collector for the selective separation of apatite and calcite minerals. The hydrophobicity studies were carried out using a computer controlled contact angle goniometer. Additionally, the collector adsorption was evaluated via electrophoretic mobility and FTIR measurements. The results indicated that a high selectivity can be obtained by using jojoba oil as collector in a slightly acid pH range, without the use of depressant. The best results were achieved with a jojoba oil concentration of 200 mg.L-1 at pH 6.5, where the apatite was fully hydrophilic and calcite showed a high hydrophobicity (? > 60 º).

Jan 1, 2014

By Arkady Senchenko

The application of centrifugal separation methods with the use of gravity concentrators has been assigned high priority while gold-containing minerals processing. The separation proceeds under centrifugal force resulted from the rotor spinning and wash water flow in the concentrators. The high specific gravity particles are retained at the trapping surface of the cone, and the low specific gravity particles are brought in the tailings. The centrifugal field in such concentrators (Knelson, Falcon) is generated by the rotating cone provoking the swirling of the free fed slurry flow. The author investigated the regularities of the separation process in the centrifugal gravity concentrator where a two-phase flow of the separated mineral media is under the pulsed pressure of the fluidization water and air. As a result of the study the possibility of the deeper penetration of the fine heavy fraction into the cone rings, providing the fluctuation of the fluidization water or air flow, was theoretically argued and experimentally proved. This allows the increase of the separation performance at low pulsation costs. The developed mathematical models are in close conformity with the actual process of interest and they enable the prediction of the heavy phase behavior at the isolated process stages in the concentrator. Keywords: gold, centrifugal gravity concentrator, containing, specific gravity, cone ring, pulsation, cost, fluidization water, Knelson centrifugal separator

Sep 1, 2012

By Ghislain Bournival, Seher Ata, Yesenia Saavedra Moreno

"In froth flotation, frothers are commonly added to the pulp to modify the interfacial properties of bubbles. These properties may be modelled using commercial software packages. The volume of fluid (VOF) method was used to track the interface motion during the post-rupture oscillation of the newly formed bubble. The aim of this research was to provide an insight into the modelling of viscoelastic phenomena through the coalescence dynamics of two bubbles in solutions of various surface tensions using a three-dimensional computational study. Different surface tensions were used to simulate changes in methyl isobutyl carbinol (MIBC) concentration. The computational results were evaluated by comparing the oscillatory motion of the newly formed bubble for the different MIBC concentrations. For known MIBC concentrations, the deviations of the computational damping constants from the experiments were quantified, revealing possible deviations in the VOF surface tension model. In addition, the analysis provided insight into the flow patterns of the fluids and the effect of frother concentration on the velocity magnitude in the liquid and air phases. This analysis provided a further understanding of coalescence dynamic and post-rupture oscillation in froth flotation. Such a process is believed to affect the stability of particles at the interface due to the release of surface energy when the bubble surface is reduced.INTRODUCTIONIn froth flotation, bubble coalescence is an important phenomenon that is highly dependent on the interfacial properties of the liquid film between bubbles. It is known that the frother adsorption at the liquid-air interface changes the interfacial properties, resulting in an increase of surface elasticity and reduction of surface energy (Pugh, 2016). However, in a two-phase system, it is the frother type, concentration, frother molecule conformation at the interface and viscoelasticity properties that dictate film stability (Pugh, 2016). The viscoelasticity phenomena can be explained in terms of surface viscosity, which quantifies the energy dissipation at the interface and surface elasticity that represents the energy absorbed at the interface as result of bubble oscillation (Pugh, 2016). In the case of systems stabilized by nonionic frothers, it has been shown that surface forces alone do not account for film stability, but the viscoelasticity represents the ability to damp external disturbances in the thin film separating the bubbles and prevent coalescence (Santini et al., 2007)."

Jan 1, 2018

By I. H. Mukhametshin, E. N. Baranova, I. B. Fadina, E. A. Ashirbaeva

The purpose of the research is the development of a complex of solutions for the maximum extraction of non-ferrous and precious metals from persistent mineral raw materials by heap bioleaching from spent heap leaching (HL) stacks. Methodical recommendations for assessing the suitability of primary and technogenic refractory mineral raw materials for heap bioleaching are developed. Active associations of microorganisms have been created for the conversion from various types of ores to the solution of S, Fe, As, Sb, Cu, Zn, Mn, Ni, Mg, P and other elements, as well as methodologies for their storage, immobilization and preparation of bioreagents in industrial conditions. On a pilot scale, tests were carried out on samples weighing 15-17 thousand tons of refractory gold-sulphide ores (more than 50% of gold is associated with sphalerite), gold-quartz ores with colloidal gold (74% associated with quartz and pyrite) and gold-silver ores with elevated copper and zinc content (1.5 and 3,5%, respectively), as well as man-caused material lying for 4-5 years of spent quarry material of oxidized gold-silver ores. In the pilot-industrial tests of heap bioleaching of gold-sulfide ores, gold recovery of 84-85% and silver was achieved to 89-90%, the possibility of obtaining high-yield solutions of copper and zinc, suitable for hydrometallurgical processing, from gold-silver ores, and the possibility of obtaining waste with a dump content of valuable components, suitable for deep disposal in the construction industry. When comparing two technologies for processing refractory ores after biooxidation under HL conditions, when 1000 tons of ore processed by the bioreagent were re-milled from a size of 40 mm to 0.1 mm and cyanated under the conditions of the factory process, the same results were obtained for gold recovery (85%) and silver (90%), as with the heap version. The copyrights of the development are protected by a patent.

Jan 1, 2018

By Kaioeng Wang, Qi Liu, Yahui Xiang

"In the differential metal sulfide ore flotation it is desirable to replace the toxic inorganic depressants with environmentally benign chemicals. Chitosan, as a natural and non-toxic polymer, has been proven to be an efficient depressant for chalcopyrite while allowing galena to be floated by xanthate collectors. However, the poor solubility of chitosan limits its potential applications as the flotation could only be carried out at about pH 4 where chitosan is soluble. A carboxymethyl derivative of chitosan, named N-carboxymethyl chitosan (N-CMC), was synthesized by substituting the amino groups of chitosan with carboxymethyl groups. The substitution significantly improved the solubility of chitosan. The structure of N-CMC was studied and compared with chitosan via Fourier transform infrared spectroscopy (FTIR). Flotation tests were performed on single minerals and mineral mixtures (with weight ratio of 1:1) with the addition of appropriate amount of potassium ethyl xanthate (KEX) and N-CMC. The solution pH was varied from neutral to alkaline. The flotation concentrates and tailings were collected and analysed for the contents of copper and lead. FTIR measurements showed that new peaks of C=O stretching of -COOH and N-H deformation of -NH- appeared in N-CMC, which indicated that the carboxymethyl groups were introduced and the amino groups were the sites for the substitution. Flotation results indicated that N-CMC could depress either chalcopyrite or galena depending on the pH. The results were not affected by the sequence of KEX and N-CMC addition. Therefore, N-CMC is potentially useful in Cu-Pb sulfide separation following a bulk Cu-Pb flotation. The N-CMC was also found to have surface cleaning functions, and was able to remove contaminating copper ions from galena surfaces. Therefore, its application in sulfide ore flotation is expected to be more robust than the original chitosan."

Jan 1, 2014

By Brochot. Stephane, Manuel Gonzalez Fernandez

"HPGR (High-Pressure Grinding Rolls) is widely used today for grinding of various kinds of ores such as iron ore or base and precious metal ores. It can be used as first stage of grinding replacing tertiary crusher and SAG mill, but also as regrinding stage to enhance mineral liberation. In addition to better energy efficiency, the advantage of HPGR is to produce much more internal particle fractures allowing faster leaching as it has been demonstrated for some gold ores. This grinding mode of compression and fracture generation also promotes mineral liberation without overgrinding. Mineral processing modelling and simulation associated to detailed ore characterization constitute a powerful tool for plant design and optimization. The mathematical models of the units of operations (grinding and separation) have to reproduce the mineral deportment for which the mineral liberation plays a central role. The present paper is focused on the HPGR modelling with the objective of plant optimization or advanced design from pilot plant tests. The traditional approach of the population balance linked to the energy dissipation and the residence time distribution is generalized in association with a mineral liberation model. The effect of the specific HPGR breakage matrix and grinding function on the mineral liberation rate is discussed and compared to the tumbling mill. The implementation of this mathematical model into a plant simulation tool is illustrated by the example of the optimization of an iron ore concentrator."

Jan 1, 2014

By Xingshi Yang, Ghislain Bournival, Seher Ata

"Particle-laden interfaces are a fundamental research topic in froth flotation since the process involves particle-coated bubbles in both the pulp and the froth phase. In most experimental studies the characteristics of the particle layer in multi-bubble systems are poorly defined. An experimental setup has been developed based on a Langmuir-Blodgett (L-B) trough. The modified trough allowed introducing an air bubble beneath the particle monolayer formed at the air-water interface which made the study of the interaction between the bubble and the monolayer under various pH values possible. The monolayer characteristics of the particles were also studied and compared in terms of surface pressure (?-A) isotherms and packing factor. On compression, the particles formed branched structure at high pH whereas a uniform monolayer was formed at lower pH. Observations related to the behavior of particles during compression and expansion cycles, and the coalescence of a bare bubble with the flat particle laden interface were provided and the implication of the results for flotation process was discussed.INTRODUCTIONFroth flotation is known for its versatility and ability to concentrate low-grade, complex ores. It is considered a physico-chemical process in which particles attach to air bubbles, depending on their hydrophobicity as well as other factors, and are carried to the surface to form a froth layer. Reagents are used to stabilize bubbles and the froth layer (Pugh, 1996). However, particles, which are carried by the bubbles or entrained, significantly contribute to the stability of the froth phase (Ata et al., 2003; Zanin et al., 2009; Bournival et al., 2015a). Their relevance in mineral processing has led to a number of fundamental studies on the effect of particles and their properties on the process of froth flotation.Flotation systems are particularly difficult to characterize due to the broad range of properties of particles (e.g. size, liberation, hydrophobicity, etc.) and inconsistent operational conditions (e.g. changes in water quality, reagent addition, etc.). Several studies have made the use of well characterized particles in laboratory conditions. Such studies allowed the finding of an optimal contact angle for the stabilization of the froth phase (Johansson and Pugh, 1992; Ata et al., 2002). Froths have a large number of bubbles so that individual interactions are not observed. The study of two bubbles allows to determine the stability of the bubbles, with particles, and to some extend the stability of the bubble-particle aggregate (Gourram-Badri et al., 1997; Bournival et al., 2015b). The removing of particles between two bubbles may also be studied from a Scheludko cell (Johansson and Pugh, 1992) or by observing a bubble with a flat interface (Sethumadhavan et al., 2002). However, these systems provide limited information on the arrangement of the particles."

Jan 1, 2018

By Narasimha Mangadoddy

The complex nature of multi-phase flow in dense medium cyclones has restricted plant operators and designers to rely on empirical equations for predicting the performance. A number of empirical cyclone models have been developed in the past (Wood, 1990; Dunglison, 2002). In recent years, this subject has been broached with computational fluid dynamics (CFD). Most of the CFD models have not considered the correct rheological behavior of magnetite medium while simulating the medium segregation inside the cyclone. These models mostly predict excessive underflow volumetric flow rates. In this paper simulations of magnetite medium in a dense medium cyclone, were conducted in FLUENT where the particle phases were simulated using the modified Mixture model. The turbulence was resolved using Large Eddy Simulation (LES) model. The rheological behavior of medium was considered in the form of Granular viscosity, Newtonian and Non-Newtonian models corrected with particle loadings and fraction of ultrafines. Multi-phase simulations using granular viscosity option although predict the overall split product medium densities reasonably close to experiments, the mixture viscosity values are restricted to substantially lower values, similar to water viscosity. Simulations using Newtonian viscosity model corrected with particle loading, and fine fraction below 53µm size is predicting overall mixture viscosity levels well over water viscosity levels, but under predicting the under flow the underflow medium density. Multi-phase simulations using Non-Newtonian Herschel-Buckley model, calibrated for superfine magnetite medium measured viscosities, is closely predicting the medium segregation with gamma ray tomography data. Overall predicted product medium densities, underflow volume split are close to the experimental data. This model is can be further used to simulate coal portioning and hence in developing new designs.

Sep 1, 2012

By Di Liu, Yongjun Peng

"It was identified that clay minerals adversely affect fine coal flotation through slime coatings. In the study, it was interesting to find that an anionic polymer dispersant, lignosulfonate, successfully mitigated the negative effect of clay minerals in coal flotation using fresh water, but in saline water, it exacerbated coal flotation.In order to understand the mechanisms underpinning the different behaviour of lignosulfonate in coal flotation using fresh and saline water, the adsorption isotherm, and dynamic light scattering (DLS) measurements were conducted in this study. While DLS monitored the molecular conformation change (swelling or shrinking) of the polymer in fresh and saline water, adsorption isotherms enabled polymer adsorbed amount on clay and coal mineral surfaces to be determined. It was found that lignosulfonate adsorbed on the coal and clay mineral surfaces providing effective electrostatic repulsions and resulting in a mitigation of clay minerals from coal surfaces in deionised water. In the presence of saline water, however, polymer molecular conformation changed. Polymer molecules were compressed and adsorbed in form of aggregates. The adsorption amount of lignosulfonate on clay minerals increased in saline water. A low dosage of lignosulfonate could not provide sufficient electrosteric repulsion to disperse clay minerals. Moreover, the high adsorption amount of the polymer on coal and clay surfaces led to a more hydrophilic coal surface, and coal flotation was therefore depressed in saline water. This study provides a new insight into understanding the role of anionic polymeric dispersants in mineral flotation using different quality water."

Jan 1, 2014

By K. A. Natarajan

"Interaction with microorganisms results in significant surface chemical changes on minerals. For example, chemolithotrophs such as Thiobacillus ferrooxidans and Thiobacillus thiooxidans significantly alter the surface chemistry of several sulfide minerals such as pyrite, chalcopyrite, sphalerite and galena. Heterotrophic bacteria such as Bacillus sp. could alter the electrokinetic properties of oxide minerals such as hematite, alumina, silica, kaolinite and calcite. Microbe-mineral interactions could thus be beneficially utilised in mineral beneficiation as different from bioleaching. Microbially induced mineral beneficiation unlike bioleaching deals with interfacial phenomena at mineral-solution-bacteria interfaces and surface chemical changes are brought about at very rapid rates amounting to a few minutes resulting in mineral separations in an aqueous medium.In this paper, the role of acidophilic chemolithotrophs such as Thiobacillus thiooxidans and neutrophilic heterotrophs such as Bacillus polymyxa in the beneficiation of sulfide and oxide minerals is illustrated. Mechanisms of bacterial attachment on various sulfide and oxide minerals are outlined with respect to the influence of bacterial interaction in bringing about mineral surface hydrophobicity or hydrophilicity. The role of bacterial cells as well as metabolic products such as bioproteins and exopolysaccharides in significantly altering the surface chemistry of sulfide minerals such as sphalerite and galena and oxides such as hematite, alumina, silica and calcite is discussed with probable mechanisms. Possibilities of generating mineralspecific bioreagents are outlined with respect to bacterial adaptation to mineral substrates."

Jan 1, 2003

By Egbert Burchardt

"Some of the challenges faced by the mineral industry in the future are the need to process low grade ores at the lowest operating cost, to deal with elevated energy cost and to address scarce water resources in some regions of the world. These challenges will increase the demand to develop highly energy-efficient and less water-consuming mineral processing systems. Experience from other industries suggests that HPGRs could help to achieve these goals, due to their high energy efficiency and their ability to be used as dry grinding systems. Historically, HPGRs have been used mainly as tertiary crushers in mineral applications for the production of ball mill feed. In the cement industry, however, HPGR systems have been successfully applied for grinding limestone, clinker and slag to a final product fineness (p80) of between 30 and 90 µm without the need of downstream ball milling. The total energy consumption of HPGR finish grinding systems in the cement industry has been found to be 30 to 50 % lower than in ball mill systems. This leads to the question of whether the same methodology can be adopted in the mineral industry. Such a step would require the use of dry rather than wet grinding systems. Traditionally, dry grinding systems have been only an exception in mineral processing, since most post grinding processes are wet. However, there are successful - mainly ball mill based - dry grinding examples in gold, nickel or iron ore. Experience from some of these dry grinding references are summarized in this paper. In addition, this paper explores two future-orientated questions: What opportunities does HPGR finish grinding offer the mineral industry? What are general conditions and challenges for adopting this technology for mineral applications?"

Jan 1, 2014

By Alexander E. Sobolev

The kinetics of oxidative dissolution of lead sulfide in solutions of nitric acid and sodium hypochlorite was studied using the rotating disk method and the factor experiment design. The dependences of the PbS dissolution rate on concentration of oxidant (HNO3 or NaOCl), temperature, disk rotation frequency, and duration of interaction were determined. The adequate kinetic models allowing calculating the specific dissolution rate at any combination of values of the influencing factors were obtained. As a result of the complex analysis of kinetic parameters, the modes of the each process proceeding were established, their macromechanisms were determined, and the limiting stages of the oxidative dissolution processes were revealed. The dissolution kinetics of lead sulfide in solutions of nitric acid was found to have several regimes. At HNO3 concentrations below 0.5 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled. It is caused by low oxidative activity of HNO3 and considerable diffusional diffuculties at this acid concentration range. At the nitric acid concentrations more than 0.5 mol/L and less than 6.0 mol/L, the process was found to be kinetically controlled. The limiting stage of the interaction is the surface chemical reaction. The observed relatively high order of the dissolution rate with respect to the concentration of HNO3 was explained by the autocatalytic action of the acid reduction products. At nitric acid concentrations exceeding 6 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled, and the dissolution rate sharply decreased that was explained by a decrease in the solubility of reaction products. When lead sulfide is dissolved in sodium hypochlorite solutions, at first time the amount of PbS transferred into solution remains close to zero. Gradually, as time goes, this amount begins to increase sharply. The dissolution rate rises and reaches the maximum value, further remaining constant. At the steady-state regime, the dissolution rate is independent of the duration of interaction and disk rotation frequency. The process was found to be kinetically controlled. The limiting stage is likely to be chemical reaction on the surface of solid lead sulfide. The obtained kinetic characteristics enlarge the database on hydrochemical oxidation kinetics of sulfides and can be used for the elaboration of the recommendations for the effective comprehensive exploitation of lead-bearing ores and concentrates. Keywords: lead sulfide, nitric acid, sodium hypochlorite, hydrochemical oxidation, dissolution kinetics

Sep 1, 2012

By Luís Marcelo Tavares, Juliana Segura

Comminution is one of the most energy consuming stages in a mineral processing plant. This consumption is not only related to the power supplied to equipment, but also to the indirect or embodied energy, mainly associated to materials that are worn during operation, including grinding media and liners. Until recently, preparation of iron ores in Brazil did not use comminution intensively, given that plants mainly produced sinter feed, natural pellet fines, besides lump ore. However, with decreasing ore grades, size reduction now occupies a centre stage in nearly all new plants. Technologies used up to date for processing low-grade iron ores in Brazil, in particular itabirites, have consisted of three or four stages of crushing followed by ball milling. A number of new plants are either being built or are currently being designed that will process the same type of ore, so that engineers are investigating alternative comminution routes. The paper analyses comparatively four comminution routes for processing a particular itabirite ore, many of which using technologies and layouts that have not yet been used in such application. Using data from bench scale and/or pilot-plant tests, the different routes are compared on the basis of sustainability principles in accordance to the Brazilian energy matrix, which is quite particular. It is concluded that if the sustainability criterion is used, then the optimal route would correspond to a circuit that uses HPGR technology with truncated feed followed by ball milling. Given the particular case of itabirite iron ores and specially to the one in the present work and the source of Brazilian energy, it is evident that indirect energy expenditure in comminution plays a significant role in greenhouse gas emissions when compared to direct energy, being the reason for the great attractiveness of HPGR technology. Evidently that these will have to be balanced against CAPEX, OPEX, NPV and other qualitative criteria, which can certainly lead to a different optimal circuit.

Jan 1, 2014

By Y. S. Sun, P. Gao

Compared with conventional roasting and magnetic separation processes, higher reduction temperatures and stronger reducing atmospheres are used in reduction technologies to reduce iron oxides to metallic iron, which is often liberated during reduction and amenable to magnetic separation. Reduction and magnetic separation of an Australian refractory iron ore was therefore studied as a function of reduction temperature, time, coal addition, feed thickness and size of Australia iron ore. It was found that during reduction, the particle size of the reduced iron increased with reduction temperature and time. Subsequent magnetic separation tests were further conducted on the reduction products. A reduced iron powder with a Fe grade of 85.67% was obtained at a Fe recovery of 87.82% under optimum reduction conditions where a metallization rate of 85.82% was achieved. The mechanism involved in reduction is discussed based on XRD and SEM examinations. And the results indicated that theiron minerals such as hematite and limonite in the Australian iron ore were reduced as follows: Fe2O3?Fe3O4?FeO?Fe. Furthermore, the metallic iron particles produced by reduction increased in size with longer reduction times.

Jan 1, 2014

By Hongchun Lou, Yan Zhang, Xianjun Lu

"The potential of Fe(NO3)3 modified attapulgite was assessed for the adsorption of phosphorous removal from aqueous solutions. Natural attapulgite was modified by Fe(NO3)3, and thus the composite adsorption materials could be obtained. Also phosphorous adsorption characterization on the iron-coated attapulgite was investigated in this research. Taken overall the results suggested that phosphorous adsorption capacity could be improved markedly by adopting ferric modified-attapulgite. The optimum phosphorous adsorption were developed in the experimental conditions of the solid-to-liquid Ratio 1g/L, the initial phosphorous concentration 5 mol•L-1, reaction time 120 min, temperature 25 ? and pH=4.0, the removal efficiency is 92.28% for the modified attapulgite. In comparison of batch experimental results of phosphorous adsorption onto natural and iron-coated attapulgite, it has provided much more likely the same change trend. On the other hand, the outcomes of this analysis indicated that ferric modified adsorbent was notably influenced by adsorption element over natural attapulgite. The Freundlich isotherm adequately described the adsorption course of phosphorous onto ferric modified-attapulgite with the correlation coefficient R2 goodness of fit of 0.9690."

Jan 1, 2014

By S. Kelebek, A. Khan, J. Caceres, D. Beckett

"Pyrrhotite in nickel-copper sulphide ores is nickeliferrous and intimately associated with pentlandite. Due to its low nickel content, pyrrhotite rejection is an important step in processing of these ores. In our laboratory, various reagents were investigated for their effect on pyrrhotite depression. Among these, a combined use of triethylenetetramine and sodium metabisulphite was found highly promising.The work described in this paper has two parts. The firs part is a summary of results obtained on process samples from the pyrrhotite rejection circuit at Falconbridge’s Strathcona Mill. The second part involves simulation of the circuit performance based on the reagent conditions used in the experimental work and the concept of split factors.Two sets of reagent conditions were evaluated. The first one involved baseline conditions, simulating the current reagent performance. The second one simulated the impact these new reagents can have on the circuit performance.The simulation results obtained under baseline conditions indicated a good agreement with the current circuit performance (Figure 1). The simulation results suggest that at practically the same pentlandite recovery and tailing grades, the circuit concentrate nickel grade can be doubled through effective pyrrhotite rejection by these new reagents (Figure 2)."

Jan 1, 2003