Search Documents

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even where possible, equilibrium data with a suitable Henry.s law constant are seldom available.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, KGa values can be calculated for the pilot plant and then scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance."

Jan 1, 2003

By Z. T. Yuan, S. L. Qi, Q. Y. Meng, G. X. Zou, L. X. Li, J. W. Lu

"The selective separation of pentlandite from serpentine was investigated using the magnetic coating-magnetic separation by conditioning slurry pH value, stirring speed, magnetic field intensity and controlling dosages of sodium hexametaphosphate (SHMP) and sodium oleate (SO). The optimal conditions were obtained as follows: the natural pH of 6.8-7.2, stirring speed of 2300 rpm, magnetic field intensity of 200 kA m-1, SHMP of 60 mg L-1, and SO of 400 mg L-1. Results showed that the Ni grade was 21.4% with the Ni recovery of 81.4% and MgO content of 3.8%. FTIR indicated that coagulant of SO preferentially adsorbed onto pentlandite and magnetite particles while hardly adsorbing onto serpentine particles when dispersant of SHMP was used. Thus, the selective magnetic coating of magnetite on pentlandite surfaces could be formed due to the formation of hydrophobic surfaces on pentlandite and magnetite particles. Calculations of DLVO (Derjaguin-Landau-Verwey-Overbeek) confirmed that interactions between magnetite and pentlandite particles were much stronger than that between magnetite and serpentine due to the existence of hydrophobic interactions with the addition of SO. Consequently, the pentlandite was successfully separated from serpentine. Therefore, this study exhibits the potential to separate pentlandite from serpentine minerals for practical applications and thus deserves further study.INTRODUCTION It has been well known that the separation of pentlandite from serpentine is a worldwide challenging issue in the processing of sulphide nickel-copper ores. Because the serpentine mainly causes the high pulp viscosity and slime coating on the pentlandite, which interferes with the flotation process of pentlandite (Cao et al., 2016; Feng et al., 2012). The fibrous mineral of serpentine preferentially attaches to the air bubble, forming bubble-macrofibers aggregates, which are easily floated into the nickel concentrates, resulting in the decline of Ni grade (Alvarez-Silva et al., 2016; Kusuma et al., 2014). In addition, the serpentine adheres to the pentlandite as hetero-aggregation or slime coating via the electrical interaction between a positively charged serpentine and a negatively charged pentlandite, which decreases the hydrophobicity of pentlandite and reduces the collector adsorption (Feng et al., 2013). In other words, the presence of serpentine or the occurrence of aggregates (including slime coating and bubble-macrofibers aggregates) seriously affects the flotation process and deteriorates the flotation of pentlandite. Therefore, we propose magnetic separation to recover pentlandite from serpentine with the magnetic coating technology, which is different from forth flotation."

Jan 1, 2018

By Dietmar Freyhammer

Grinding is the last stage of the comminution process. In the grinding process the particles size are reduced by impact and attrition stresses. The fine grinding of ores is nowadays finding increased application due to depletion of coarse grained, easily processed ore bodies and the increased need to process distributed fine grained deposits, such fine ground iron ore powder is the basis for the pelletisation process. Depending on the ore type and the project environment different approaches to comminution are requested to provide an adequate ground iron ore for the pelletisation process. Currently the ball mill is the most used equipment in grinding iron ore for pellet feed. Based on the various examination and investigation of minerals on grind ability related to the throughput, to the resulting sieve characteristics and necessary energy consumption, the mill circuit can be: Open dry circuit. Closed dry circuit Open wet circuit Closed wet circuit. CEMTEC GmbH is a renowned name worldwide and offers tailor made solutions to cope these issues.

Sep 1, 2012

By H. Araneda

Throughout Chile?s history, mining has consistently been a leading industry in the country. The 1990s marked the beginning of a boom in Chile?s mining industry, especially in copper mining, due to both foreign and local direct investment in the sector. Mining?s contribution to the GDP was 15.6% at current prices in 2009, and it accounts for 56% of the country?s exports. Chile?s copper market share reached 35% in 2009. The investment portfolio in mining in Chile for the coming decade has been estimated at 90 billion US dollars. The acute scarcity of human resources currently experienced by the mining sector in Chile will be accentuated in the coming decade as a result of this scenario of investments. The situation is, additionally, similar to the one confronted by other countries involved in the mining industry such as Australia, South Africa, Canada, and in Latin America includes, Peru, Colombia and Brazil. A study carried out by Fundacion Chile, ¨Labor Force in the Chile Mining Industry, Diagnostic and Recommendations, 2011-2020? shows the projected labor shortage for the operation of projects in the development stage, considering only the requirements of the process of extraction, processing, and maintenance. The demand, accumulated incrementally, will be around 115,000 technically skilled workers, professionals, and qualified workers. This figure refers to the operational work force, and does not include the human resources that will be required for the prior stage of the engineering and construction of the projects (brownfield and greenfield). The demand for technically skilled workers and professions for the stages of engineering and construction of the projects that have already received investments is estimated to be 190,000 people for the period 2012-2020. The peak of the demand for engineering is 2012, with a figure that surpasses the 12,000 professionals for all of the engineering specialties. The analysis of the formation of human resources at the tertiary level (where tertiary includes technical/vocational and academic degrees at the undergraduate level) for mining and related majors demonstrates that the programs are scarce with a bias toward theoretical contents and that they are excessively long (40% longer than comparable programs in Australia, Canada, and in OECD countries). The completion rates are low, especially in the technical-vocational programs, which have a completion rate of only around 30%. Finally, the rates of attraction of technically skilled labor and professionals towards careers in mining are insufficient to reduce the identified skill gaps. In the case of university professionals such as geologists, mining engineers and engineers in metallurgy, 80-90% will work in mining. In the case of graduates of relevant majors, that cover skills also utilized by other industries, not only mining?such as maintenance workers, operators of fixed and mobile equipment, etc.?the mining sector appears to be unattractive for reasons such as shift schedules, geographical location of work sites, and other factors. On the basis of the available diagnosis a strategy for the sector has been developed (Workforce Development and Skills Strategy) whose objective is (i) to define a Mining Qualifications Framework to identify the critical roles to be filled (ii) to start, with public resources, a ¨fast-track? training program to assure the availability of at least 28,000 operators (machinery operators, truck drivers, etc.) and maintenance specialists in 2015 (iii) to promote the development of training hubs for mining with learning technologies to train technical labor and professionals on the basis of world class standards (iv) to design and implement a campaign oriented toward the perception of mining as an attractive field of employment opportunity (v) to develop curricular innovations for tertiary education programs, on the basis of international benchmarks. Keynotes: Chile, mining, copper mining, skilled human resources

Sep 1, 2012

By Chuanyao Sun, Yang Yu, Zhen Guo Song, Wei. Ming’An

"Carbonate minerals are very important mineral source of extracting metal, radioactive element and rare earth elements. Furthermore,some carbonate minerals, such as calcite and dolomite, are common and important components of sediments and sedimentary rocks. Many flotation processes involve the separation of valuable minerals with carbonate minerals. So it is of great significance to the flotation theory and industrial practice to investigate the flotation behaviors of carbonate minerals. As regulators, metal ions play a major role in minerals flotation. The study of influence law of metal ions on minerals flotation is helpful to eliminate or utilize the effect of metal ions. In this study, calcite and smithsonite laboratory scale flotation, surface analysis and zeta potential determination in the presence of Fe(II) ion were performed to investigate the effect of Fe(II) on carbonate flotation. The results show that Fe(?) depresses the flotation of calcite and smithsonite. The depression effect of Fe species on calcite and calamine flotation can be improved with the increase of Fe(?) concentration. The zeta potential measurements and surface analysis show the existence of iron hydroxide products on mineral surface, which may be link to carbonate site instead of exchanging with calcium on the mineral surface. Fe species on the mineral surface inhibit the interaction between the reagents and calcite/smithsonite through the formation of surface precipitation coating on the calcite/smithsonite surface when the Fe(?) concentration is higher."

Jan 1, 2014

By Khoi Nguyen, Keeney. Luke

An outcome of geometallurgical mapping and modeling is the generation of continuous down hole profiles of quantitative geometallurgical attributes at assay scale. These attributes vary from traditional routine data collection methods such as assays and geotechnical logging (e.g. RQD, Fracture Frequency), to new measurements including petrophysical attributes, EQUOtip hardness data and modelled estimates of metallurgical performance indices (e.g. A*b, BMWi). Highly variable continuous geometallurgical data with high spatial resolution can make it difficult to identify spatially continuous domains. An automated method based on the well known time series analysis technique of cumulative summation (CuSum) has been developed which uses statistical analysis to identify domain boundaries in down hole profiles. A bootstrap analysis automatically identifies potential domain boundary locations with associated confidence levels and a series of t-tests determine the significance of defined populations. A hierarchical clustering algorithm is applied to results to enable data sensitivity to be taken into account. The method produces statistically significant populations and is suitable for application on either single or multiple drill hole datasets. Domains defined preserve the inherent variability of the continuous down hole data and provide a method for scaling up variability data (i.e. assay interval scale) to mine scale (i.e. bench scale, block model). A major advantage of the method is its ability to provide suitable input parameters for use in spatial modeling of non-additive and non-linear geometallurgical attributes through conditional simulation techniques.

Jan 1, 2014

By S. Gaydardzhiev

Laboratory batch tests having preliminary and orientation character aiming at improvement of the molybdenum flotation at Ellatzite copper processing plant in Bulgaria have been conducted. The following technological parameters have been screened to study their influence on the grade and recovery of copper and molybdenum during the rougher flotation stage: flotation pulp density, pH, addition of secondary collector and replacement of MIBC by pine oil as a frother. The results have shown that slightly better grade/recovery figures could be obtained for both copper and molybdenum at lower flotation pulp densities. The addition of kerosene has improved the recovery of molybdenum however, on the expense of that of copper. The effects from pH variation and the replacement of MIBC by pine oil as a frother have been almost negligible.

Sep 1, 2012

By M. Naymanbayev

The characteristics of the mineral composition of ores and valuable set of components: the technology of processing depending on the type of mineralization, the nature of the impregnation of ore minerals and their composition have been considered. There have been given technological schemes for processing concrete objects. The analysis of fitness fields for industrial development (degree of scrutiny, the effectiveness of developed enrichment and hydrometallurgy technology) has been provided.

Sep 1, 2012

By Gurubasayya Swamy

This paper presents the performance study of sag mill in the processing of gold ore. Deterioting ore grade and high demand of metals has tremendously influenced the SAG mills. Today?s high capacity Semi-autogenous grinding (SAG) mills expand vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. Semi-autogenous (SAG) mill performance is influenced by ball charge, feed properties, shell, grate, and pulp lifter design. In the performance study of SAG mill, based on the results obtained it can be observed that SAG mill performed better at feed size +4 inch and grinding media consumption 0.90kg/mt. In the present study the effect of crusher bypass on SAG mill performance, an immediate drop of throughput ranging from 10-20tph is observed. Keywords: sag mill, pulp lifters, grinding media, energy, consumption, throughput

Sep 1, 2012

By Takashi Furuyama, Sukeyuki Mori, Tetsuo Ikejiri, Abel Bissombolo, Yoshitsugu Koga, Masamichi Hata

In Japan, the increasing number of automobiles newly put into circulation is followed by a larger amount of end-of-life vehicles from which valuable metals are being recovered in shredder and related plants. Nevertheless, the processing of these scrapped automobiles which has reach a recycling rate of about 75%, generates a huge volume of waste, locally known as .shredder dust., which is commonly dumped on landfills. The saturation and depletion of valuable disposal sites in the near future, as well as the social and environmental problems related to the accumulation of these residues disposals are a major challenge for the automobile shredding industry. To promote an alternative way for the management of these disposals, the authors have initiated and developed a system for their processing, on the basis that more than 90% of these residues are combustible materials that could be used as refuses derived fuel. The developed processing system points out the mechanical/physical separation of shredded automobiles residues into two streams by means of an ascending airflow passing through a vertical zigzag separator and, the compaction of the light-density fraction of materials (that is about 60% of auto shredder residue recovered as float products and mainly composed of cotton, sponges and light plastics) to form a refuse derived fuel (RDF), the density, calorific value and ignition loss of which are 1.19 g/cm3, 4470 kcal/kg and 60.7%, respectively.

Jan 1, 2003

By S. S. Indi, D. Santhiya, S. Subramanian, K. A. Natarajan

The interaction of sphalerite- and galena-adapted Bacillus polymyxa (B. polymyxa) cells with sphalerite and galena has been investigated through adsorption, electrokinetic and flotation studies. The amount of sphalerite-adapted cells adsorbed onto sphalerite and galena is found to decrease with increase in pH. On the other hand, the adsorption density of galena-adapted cells onto galena shows a feeble maximum around pH 8, and the amount adsorbed is marginally higher in the pH range of 8 . 11.5. In the case of sphalerite the amount adsorbed is higher in the pH range of 5 to 7. The adsorption density of both the adapted cells is higher for galena vis-à-vis sphalerite. Electrokinetic studies indicate significant surface chemical changes on the chosen sulphide minerals and the bacterial cells, consequent to microbe-mineral interactions. Selective flotation tests on a synthetic mixture of galena and sphalerite confirm that sphalerite could be preferentially floated from galena, using galena-adapted cells, but not with the sphalerite-adapted cells. The cells adapted to galena assay a higher polysaccharide content and are more hydrophilic, while the sphalerite-adapted cells have a higher protein content and possess greater hydrophobicity. Transmission electron microscopic studies have provided evidence in support of the differences between the cell surface characteristics of sphaleriteand galena-adapted cells. Possible mechanisms of interaction between the minerals and the bacterial cells are discussed.

Jan 1, 2003

By Olli Haavisto, Heikki Häkkänen, Tommi Kauppinen, Navid Khajehzadeh

Raman analysis is a well-established method for finding the abundant minerals in an ore sample. In this study, Raman spectroscopy is tested as a method for rapid and contactless on-line mineral analysis. Rapidness might enable on-site analysis of rock drillcore, which in turn would lead to more cost-efficient solutions in mineral exploration. This paper discusses the use of Raman analysis to identify minerals and to measure their concentration. The sample set under study consists of rock drillcore collected from Agnico-Eagle Kittilä Mine, Finland. Selected parts of the sample set are measured by Raman spectroscopy and the minerals are identified using reference spectra from a public source. Moreover, the direct measurement of concentration of different minerals with the help of Non-negative least squares (NNLS) optimisation algorithm is considered. The optimisation algorithm was constructed to form a linear combination of reference spectra which best represent the measured spectrum, or an average of measured spectra, from an ore sample. The results show that NNLS can identify abundant minerals in a given sample. Also through this method of analysis the results of a traditional point-count method can be expanded: It was observed that, due to grain size, multiple minerals consistently appear in the spectra measured over an area, which means that point-count method is not a proper way to interpret the spectra. This can be seen as a new result, as formerly the discussion has attended to other methods.

Jan 1, 2014

By Francesco Vegliò, Luigi Toro, Francesca Beolchini, Francesca Pagnanelli, Stefano Ubaldini

"Biosorption is an innovative technology used to remove heavy metals from aqueous solutions from mining waters and other industrial wastes. A wider application of this alternative process is strictly dependent on the understanding of the chemico-physical aspects involved, in order to optimize the operating conditions. Mechanistic models are the most useful tools used for understanding purposes, even if the empirical models are still widely applied for their simplicity.In this paper especially propagated biomasses of Sphaerotilus natans, calcium alginate and some waste materials were tested as adsorbents for single and binary solutions containing heavy metals at different pH. The equilibrium experimental results were fitted according to empirical and physical models with growing complexity outlining the inadequacy of the predictive models; in fact, the non-ideal interactions among metals require the insertion of additional correction parameters."

Jan 1, 2003

By M. Gonzalez Fernandez

"Commercially introduced in 2004, the SAGDesign™ test has today proved its efficiency for sizing SAG mills for a wide variety of ores, from very soft to very hard ones. The interest of building a model using the SAGDesign™ test specific energy is the introduction of such a model into a complete process simulator making it possible to predict a complete material balance. The developed model compares the required specific energy with the energy provided by the mill. This energy calculation is derived from the Austin Power Formula. The specific energy provided by the test is corrected, using various parameters, such as the Ball Mill Work Index, to take into account the true operating conditions, the feed and product sizes. The core of this model allows the determination of the product d80 using the mill geometry, its operating conditions and of course the SAGDesign™ test results. To be included in a simulator, the model must also predict the overall size distribution of the SAG mill discharge. Assumptions to answer this point are presented here. The model has been implemented in the USIM PAC simulator. It is used either to predict the product size distribution for a given SAG mill, but also to size a SAG mill for getting a required reduction ratio. INTRODUCTION Over the last few years several types of new comminution machines have been introduced in the market. The most notable newcomer was the HPGR (Morley, 2006). But, even when these machines have some advantages, they have not earned the trust of the mining industry. That is why the established technologies still being the first choice. And, in comminution, that first choice are SAG and ball mills. The design of ball mills has been well understood for a long time. The Bond Ball Mill Work Index is the standard test which helps to describe the ore in terms of energy requirements for milling. Unfortunately, the development of an equivalent test to characterize the ore subject to SAG milling has taken some time. As of today, several tests are available in the market, like the MacPherson test, the MinnovEX SAG Power Index (SPI™), the JK Drop Weight Test, the SMC Test® and the SAGDesign™ test (Verret et al., 2011). The SAGDesign™ test, developed by John Starkey in Canada in the early 2000s (Starkey et al., 2008, 2015), has become one of the standards to assess the grindability of an ore in a SAG mill. One of its advantages is the reduced sample mass needed to perform it, hence, the reduced cost. The second one is that the output of the test is straightforward, it is the energy required to grind the ore between two sizes. Because of this energetic approach, the results provided by the test can be directly applied to size a new mill or to assess the performance of an existing mill."

Jan 1, 2018

By R. Hejazi, Saghaeian. M., H. Abedini

Continuous vacuum belt filters mainly carry out an important duty in the solid-liquid separation processes such as iron ore concentrate dewatering. However as the particles become finer, the resistance to filtration and dewatering would increase and as the result cake moisture content tends to increase. So in recent decades, using additives in order to improve the filtration performance has been considered by many researchers. In the present study, the effect of several surfactants on the filtration rate and cake moisture content of Chadormalu iron ore concentrate (80% =40 micron) was investigated using a laboratory scale vacuum filter. The results of several tests indicated that a non-ionic surfactant (Lauryl Alcohol Ethoxylated, LAE) has the best performance on reducing the moisture content of the cake and reducing the cake formation time. The optimum dose of LAE was found to be 300 g/ton which reduced the concentrate cake moisture content from 13.76 to 11.28% (wet weight base). Some industrial filtration tests were performed in Chadormalu iron ore concentrate plant to prove the effectiveness of this surfactant. The surfactant is mixed with water and added to the concentrate slurry before distributing on the vacuum belt filter. The industrial and experimental results were almost similar, so that adding about 300 g/ton of LAE would reduce the final cake moisture content from 12.87 to 10.76%.

Jan 1, 2014

By E. V. Mezentseva, S. M. Okunev

"In the article there is set forth a development experience of JSC LEBEDINSKY GOK Beneficiation Plant concerning the plan of increase in the production volumes of the iron ore concentrate with Fe content more than 69.5%. There are considered the issues regarding implementation of the updated process scheme of the concentrate beneficiation using fine screening operation, its industrial tests have shown an exploitability of this development direction. There are described the issues relating to the ceramic filters for dehydration of the additionally-beneficiated concentrate, there are given the production and process figures achieved during the exploitation. The methods of the research. In the paper there have been used the following scientific research methods: the methods of system analysis, mathematical statistics, classification, comparison, modelling, observance, experiment. INTRODUCTION JSC LEBEDINSKY GOK is the largest leading enterprise for iron ore beneficiation and the unique RF producer of the merchant hot briquetted sponge iron (HBI) highly demanded by the consumers. Raw materials for hot briquetted iron production are fluxed pellets produced from iron ore concentrate with Fe content more than 69.5% (additionally-beneficiated concentrate). Strategic program of the plant’s development foresees expansion of production of the highly demanded products that imposes a necessity of expending capacity of the enterprise and implementation in production of modern processes and equipment having low resource intensity and ensuring in addition a high efficiency. Construction of the third stage of the HBI Plant became one of directions for the strategic development of JSC LEBEDINSKY GOK implemented in 2017 that caused a demand in the production volumes and filtration of the iron ore concentrate with Fe content more than 69.5%. Purpose of the work – to develop and to provide a rationalization for efficiency of the production process and filtration of the iron ore concentrate with Fe content more than 69.5% ensuring increase of production volumes and its prime cost."

Jan 1, 2018

By Milind Chikhale, Yogesh Reja, Keshav Tyagi

"Using computer models for process design is a well-established practice in the mineral industry. In recent years, there has been emphasis on modeling of processing plant as a whole. This paper covers development of a model for iron ore processing plant. Basic purpose of this model is to use simulation for efficient plant design and help in minimizing risk at the very initial stage of project. Feed to the plant is Hematite iron ore from a deposit located in Eastern India. Major processes in plant include multi-stage crushing, screening, grinding, classification, gravity and magnetic separation. Models for different process equipment were developed using METSIM and Bruno simulation software. Customized black box models and known mathematical models were used for predicting behaviour of processes. Data needed was identified based on the model type. The required data was arranged as per project requirement and processed for development and validation of model. Equipment models were developed and validated on the basis of process design basis, theoretical and empirical data from technical references, and bench scale and pilot scale testwork results. Validated process circuits were assembled to simulate and represent the entire plant process. The result shows expected variation in plant output as a result of variation in the feed. Study concludes by discussing potential applications of the model in plant design."

Jan 1, 2014

By A. R. Videla, P. R. Brito-Parada, I. Mackay

"Linking results from laboratory scale experiments to industrial flotation behaviour is challenging. Typically, such experiments involve batch tests in which the system does not operate at steady-state, making it difficult to infer the effects that operating conditions have on flotation performance. In order to overcome this limitation a 4-litre recirculating tank was previously developed at Imperial College London. This tank is capable of reaching, and operating at, steady-state by recycling overflowing concentrate back into the feed. As well as instruments to control operating conditions, it is fitted with a system of sensors that allow the surface of the froth to be dynamically monitored. From this information, it is possible to measure the air recovery—a proxy for froth stability. Thus, this bench-scale tank can be used to understand the effect of differing operating conditions on flotation performance at steady state. However, so far, this cell has only been used to investigate idealised systems with only one or two species.Reprocessing of tailings dams is not only environmentally desirable but also increasingly economically feasible due to the declining head grades of primary deposits. There is also the added benefit of no further milling being required prior to flotation. However, the effects of fine and ultrafine particles on froth stability are not yet fully understood. In this work, the bench-scale continuous tank has been used for the first time to determine the flotation response of a complex feed, consisting of samples from a copper tailings dam, to changes in operating conditions. It was shown that the froth stability in the system is comparable to that of previous work and industrial tests, with a peak in air recovery being found at a superficial gas velocity of 1.13 cm/s. There is scope to optimize the froth stability of tailings flotation for enhanced metallurgical performance."

Jan 1, 2018

By Gabriel C. Aguilera, Juan Arismendy

"The effect of rheological factors inside of a hydrocyclone is very relevant for the fluid mechanics and for the classification of materials on suspension, since parameters such viscosity and thixotropy are intrinsic variables that depend of the particulate system and the continuous phase; they determine the efficiency of classification. Nevertheless, the exact knowledge of the main characteristics and magnitudes of them inside the hydrocyclone is very difficult because of the geometry of the hydrocyclone, even more if the hydrocyclone is of small diameter. Hence is not possible to make a hydrodynamic study with effects over classification regarding these variables. This work studies the rheological variables inside a small diameter hydrocyclone that works at high pressures, using the information given by a model of Computational Fluid Dynamics (CFD). The model used includes the Reynolds Stress Model (RSM) for the evaluation of turbulence, and the Volume of Fluid (VOF) to study the interaction between water and air, which is very important to obtain regarding the effect of the air core over the performance of the equipment. The validation of the CFD model was done with a kaolin suspension at several conditions of solids contents below the critical volume fraction, without chemical additive aid. These conditions are representative of current work parameters on plant. As result it could be established the ranges of evaluation of rheological variables on specific regions inside the hydrocyclone, and through a rheometric study, based on the mechanic characteristics previously obtained, the main rheological characteristics of the mineral suspensions were determined."

Jan 1, 2014

By Kyle P. Flynn, Frank J. Hrach, James D. Bittner

ST Equipment & Technology, LLC (STET) has developed a processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles greater than 75µm in size, the triboelectric belt separator is ideally suited for separation of very fine (<1µm) to moderately coarse (300µm) particles with very high throughput. The high efficiency multi-stage separation through internal charging/recharging and recycle results in far superior separations that can be achieved with a conventional single-stage free-fall tribo-electrostatic separator. The triboelectric belt separator technology has been used to separate a wide range of materials including mixtures of glassy aluminosilicates/carbon, calcite/quartz, talc/magnesite, and barite/quartz. An economic comparison of using the tribo-electrostatic belt separation versus conventional flotation for barite / quartz separation illustrates the advantages of dry processing for minerals.

Jan 1, 2014