Search Documents

By T. Wang

A new kind of mixed chelate collector was prepared in order to separate gangue (mainly quartz) and iron minerals efficiently during room temperature. The collector was was composed of two chelate collectors DES and DA. Floatation tests were carried out under 28?C with mixed magnetic concentrates of Donganshan sintering plant, and optimal test conditions were obtained, in which a direct floatation was undertaken and then a close circuit reverse floatation tests ( one roughing, one cleaning, and two scavenging), and a result of Fe grade of siderite concentrate 36.49%, Fe recovery of siderite concentrate 10.65%, Fe grade of final concentrate 66.27%, Fe recovery of final concentrate 78.25%, and Fe grade of tailing 16.22% was gained. Fourier Transform Infrared (FTIR) Spectra and Zeta potential of siderite and quartz adsorbed the DES and DA collectors before and after were measured in order to analyze the reaction between the collector and minerals. Furthermore, Molecule electronegativity of DES and DA was calculated by Electronegativity Proportionality Principle (EPP). Results showed that DES molecules have five active adsorbing sites and their molecule electronegativity was stronger while DA molecules have three active adsorbing sites, which all make the mixed collector has efficiently collecting performance. Zeta potential results of Quartz and siderite showed that at pH 11.5 both kinds of particles charged negative and at this pH value the mixed collector were mainly anionic collectors which indicate that electrostatic adsorption does not exist at this situation. FTIR results showed that characteristic peaks of the mixed collector changed before and after adsorption with the minerals, which means that there exists chemical adsorption or hydrogen bonding.

Jan 1, 2014

By K. Sasaki, H. Miki, Y. Muta, T. Hirajima, G. P. W. Suyantara

"Selective flotation of chalcopyrite and molybdenite is continuing problem since its selectivity is not perfect and current NaHS process needs closed system flotation plant because of hydrogen sulfide emission on acidic condition. Some alternative additives investigated as chalcopyrite became hydrophilic and molybdenite kept hydrophobic. XPS analysis indicated chalcopyrite became hydrophilic since iron and copper sulphate, hydroxide was covered on the surface whereas molybdenite kept hydrophobic since only molybdenite can be seen. Flotation experiments of chalcopyrite and molybdenite mixture sample indicated excellent separation that 95% of molybdenite can be recovered as froth and 93% of chalcopyrite can be recovered as sink. Flotation experiments with real bulk flotation concentration indicated similar separation result compared with current NaHS additive system. Possible mechanisms and detailed phenomenon were investigated based on the surface analysis and thermodynamic calculation etc. this alternative additive is easy to handle compared with NaHS since it does not emit effluent gas and commercially preferable.INTRODUCTIONMany copper mine often associates molybdenite (MoS2) as trace mineral. It is important to separate molybdenite and copper mineral efficiently since molybdenite is valuable mineral and also contamination of molybdenite into copper concentrate decrease concentrate value. Conventional separation of copper sulfide and molybdenite has been achieved with sulfide bulk flotation followed by selective molybdenite flotation with NaHS addition since NaHS works as a depressant for copper sulfide (Bulatovic, 2010; Ansari and Pawlik, 2007b). However, this current process shows imperfect molybdenite recovery (Liu et al., 2012, Zanin et al., 2009) and depressant such as NaHS needs to be used under specific flotation plant since it might be environmental contaminant (Ansari and Pawlik, 2007a). there are still unknown on the effect of depressant NaHS, but one of the theory is NaHS reductant effect. It is worth to investigate the effect of other reductant as depressant on chalcopyrite. On this research, typical reductant, Na2SO3 are added to utilize for selective flotation of chalcopyrite and molybdenite."

Jan 1, 2018

By S. Banisi, Seyyed Omid Mousavi, Alireza Ghasemi

Discrete Element Method (DEM) is extensively used to simulate the behaviour of particles in various processing units. This method is based on modelling the forces acting between particles in any contact and consequently calculating the new position of particles. The high number of elements and numerous equations needed have made the required computation time very long even using computers with very fast processors. The required computation time mainly depends on the time step. If the time step is chosen very short, the computation time will significantly increase. On the other hand, if the time step is chosen very long, the simulation will be in error due to not fully observing the contacts. In DEM calculations, the time step is chosen as a fraction of the collision time. In this research, a relationship was proposed between the contact time fraction and the error of simulation. In other words, to select the time step in addition to physical parameters, the accuracy of the simulation was also accommodated in the frequently-used relationships. The simulation error was defined as the relative difference between the initial restitution coefficient and the restitution coefficient obtained after simulation. The required time steps to arrive at the simulation error of 5% were calculated for two common contact force models namely, Hertz-Mindlin and linear spring-dashpot. The simulation was performed for two particles with radius of 3 cm, elasticity modulus of 210 GPa, Poisson's ratio of 0.3 and relative velocity of 0.5 m/s. The required time steps were found to be 2.3 and 0.19 µs for the Hertz-Mindlin and the linear spring-dashpot contact force models, respectively. Results showed that with a scaling-down the modulus from 210 GPa to 2.1 MPa, the required time steps for the Hertz-Mindlin and the linear spring-dashpot contact force models, with an equal simulation error, increased by 100 and 316 times, respectively.

Jan 1, 2014

By Trevor Saldanha, Stephen Grano

A key uncertainty in flotation modelling is determining, a priori, the proportion of each mineral which will develop a certain rate constant for different feeds of variable liberation and hydrophobicity. First and foremost is the ability to predict the proportion of minerals that will not be recovered, even at very long flotation times, and which therefore report to the tailing stream as the non-floatable fraction (i.e., having a zero rate constant). Recent empirical evidence has shown there are at least two factors which contribute to heterogeneity in flotation rates and, in particular, the appearance of a non-floatable fraction - heterogeneity in the distribution of adsorbed collector amount on a particle-by-particle basis, even for the same liberated mineral in the same size fraction, and the existence of a critical contact angle below which the bubble-particle union is unstable. In this paper, inferred measures of the critical contact angle for liberated particles are compared with stability model calculations. This has demonstrated that the dependency of the critical contact angle with particle size and mineral specific gravity are explicable by bubble-particle stability considerations. This argument is further extended to the flotation behaviour of composite particles, as a function of liberation class, in which the wetting perimeter of the attached bubble on the composite particle surface is constrained by the presence of a surrounding hydrophilic domain for the case of simple binary composites. Reasons for the different flotation behaviour of composite particles having different textures, as noted in the literature, are also discussed in terms of the stability of the bubble-particle union.

Jan 1, 2014

By Kirsten Corin, Margreth Tadie, Michael Nicol, Cyril O’Connor, Jenny Wiese

"The recovery of base metal sulfides has been emphasized in the study of the flotation of platinum group minerals (PGMs). However, in some ore bodies such as the Platreef of the Bushveld Complex, sulfide minerals do not make up the majority of the more significant PGM mineralization. It is therefore important to develop a fundamental understanding of how non-sulfide and sulfide PGMs respond respectively to the current reagents being used in the flotation of these minerals. The interactions between platinum and palladium sulfides and tellurides with the thiol collectors, ethyl xanthate and diethyl dithiophosphate, have been studied using the electrochemical techniques of mineral rest potential and voltammetry measurements. The differences in the interaction between the two types of minerals with these reagents were of key interest. Rest potential measurements indicated stronger electrochemical interactions of the minerals with ethyl xanthate than diethyl dithiophosphate. These measurements also indicated that there are different forms of oxidized collector present on the mineral surfaces after interaction with ethyl xanthates. Voltammetry measurements support these observations and suggest differences of adsorption on Pt and Pd sulfides than on Pt and Pd tellurides. Voltammetry also showed that there was minimal electrochemical interaction between the Pt and Pd minerals and diethyl dithiophosphate."

Jan 1, 2014

By A. Morrison, P. Brito-Parada

"The separation of valuable and gangue minerals according to their surface hydrophobicity in a froth flotation tank occurs in both its pulp and froth phases. In the pulp phase, hydrophobic particles must be brought into contact with rising bubbles introduced at or near the bottom of the tank. In a mechanical froth flotation tank, this is primarily achieved through the agitation of the pulp by an impeller or by a rotor-stator system. However, the turbulent and mixing effects of such an impeller or rotor-stator system, necessary to promote bubble-particle interactions in the pulp, are not confined to the pulp zone, but are transmitted into the froth zone at the pulp-froth interface. This impeller-induced turbulence at the pulp-froth interface is compounded by the impulse of buoyant bubbles entering the base of the froth phase, reducing the stability, and thus separation performance, of the resulting froth. Hence, turbulence improves separation performance if it occurs deep in the pulp phase, but diminishes it if it occurs close to the pulp-froth interface. For this work, a performance-enhancing pulp phase insert was designed to isolate the impeller-induced turbulence from the pulp-froth interface in a laboratory-scale, continuously-operated froth flotation tank. The result was a shifted grade-recovery curve that allows the insert to be designed to maximize the recovery from the system without sacrificing the grade of the concentrate, or vice versa, along a spectrum of improved performance. This paper will present the insert design and development process that resulted in this improved grade-recovery curve, as well as a set of heuristics that could be used to design a similar insert for pilotand industrial-scale validation and deployment.INTRODUCTIONAn almost ubiquitous design feature of commercial flotation tanks is the enclosure of the impeller to create a concentrated turbulent zone (Mavros, 1992). These turbulent zone enclosures are varied-- from the rotor-stator design of, for instance, Outotec cells, to the air disperser design of Wemco cells-- but all share the same rationale: that turbulence is desirable to promote bubble-particle interactions (Ralston, 1999), and to produce smaller bubbles (Wills, 2006), but also undesirable because it promotes the detachment of valuable mineral particles from bubbles, and exacerbates entrainment-inducing mixing at the pulp-froth interface (Jameson, 2010)."

Jan 1, 2018

By Lina Chica, Arturo Barrientos, O. Bustamante

Hydrocyclone is a device commonly used in mineral processing industry. Underflow control plays a fundamental role in hydrocyclone operation. This affirmation supports the fact that hydrocyclone underflow has effect in some aspects of separation performance like capacity, split ratio, cut size and bypass. Hydrocyclone operation state is associated to underflow characteristics: air core formation and discharge shape. Many studies attempt to understand size separation phenomenon and the discharge influence but none of them has taken an energy point of view. This work presents the results of a mechanical energy dissipation for hydrocyclone operation from a mechanical energy balance. The experimental results related to Newtonian suspensions show that underflow energy dissipation does not control the operation because this magnitude is small compared to interior energy dissipation. However, discharge energy dissipation provides enough information to describe underflow conditions and its influence in separation conditions. In the modelling non dimensional parameters have been considered for hydrodynamic description and for geometrical and operation hydrocyclone characteristics. Energy dissipation from the continua media approximation results into a relevant concept to understand the hydrocyclone performance and improve industrial installations.

Jan 1, 2014

By H. Palza, C. Ihle, S. Contreras

"Processing of minerals, particularly treatment of tailings, has been increasingly challenged by the presence of clays in the feed of thickeners. This occurrence is expected to become increasingly important given the nature of ore deposits currently being exploited and those that have been recently discovered. In sedimentation operations (solid-liquid separation), industrial flocculants often fail to coagulate clay-containing fines, generating supernatants with high levels of turbidity, thus implying operational problems. Recently, it has been reported that graphene oxide (GO), a graphite derivative with high oxygen-containing groups, could enhance the flocculation of clay systems, due to the interaction between clays and GO functional groups. In the present work, we investigated the effect of doping industrial flocculants (commercial polyacrylamide) with GO on the floculation of kaolinite suspensions in a solid-liquid separation stage. Separation performance was evaluated by studying flocculation kinetics using a focused beam reflectance measurement (FBRM) instrument, in a set of batch tests. A statistical analysis of the flocculation kinetics and floc population distribution was further carried out. Our results suggest the existence of a synergistic effect between the studied flocculants and GO. This effect is observed as a decrease of clay fine contents in the supernatant, thus improving solid-liquid separation eficiency for high clay containing tailings. INTRODUCTION Copper, given its mechanical, physical and chemical characteristics, is a critical material for the progress of society and so has been from early stages of mankind. Demand for this metal has increased due to the growth of cities and the technological explosion, leading to increase current mining production and reinforce the efforts in exploration for new deposits (Elshkaki et al. 2016). As copper-rich deposits are being depleted, it has been necessary to develop proper technology to mine deposits of lower grades and more complex mineralogies, keeping in mind that the economic window that allows the exploitation of them is reduced by the increase on operating costs (Crowson 2012 and Northey et al. 2014). High clay bearing minerals are found in many of those low-grade copper deposits, and they induce problems in all stages of the mineral processing route (Taner and Onen 2016). Particularly, in the solid-liquid separation stage, the flocculation process fails to remove the clay fraction from suspension and it leads to operational issues such as filter damage, overconsumption of reagents and the need to add an extra clarifying step for the recovered process water. Those problematics pose an interesting challenge."

Jan 1, 2018

By S. Gomez, P. A. Bebswa, A. N. Mwale

"The research aimed at improving the way screen performance analysis is conducted using a model that accounts for most feed and design parameters in its formulation. Thus, the aim was to validate the fine screen model that was developed at the Centre for Minerals Research (CMR) unit at the University of Cape Town. Fine wet screening is increasingly becoming an important application in fine grinding operations. Minera Saucito, a lead-zinc Mexican mine has replaced hydrocyclones with eight stacks of five decker derrick screens to close the ball mill in their concentrator plant. The five decker stacks have improved the overall plant throughput by 20% and have had the ball mill circulating load reduced considerably. As a continuous plant optimization process, a number of surveys were carried out to assess the performance of the 75 µm panel aperture installed screens. The surveys were conducted at seven different feed rates to the entire nest of screens to collect performance data. Using the fine screen model to analyze the results, it is found that as the feed rate increase, the sharpness of separation reduces. The CMR fine screen model was fitted to these results. The model fits the plant data with good accuracy. Simulated results based on this model are also presented.INTRODUCTION The potential of high frequency vibrating screens has long been identified as an alternative to hydrocyclones in grinding applications (Rogers and Brame, 1985). However, high frequency vibrating screens have had two main disadvantages, low capacity and high wear rates (Kelley and Mckeon, 2005; Teknikk, 2009). Current vibrating screen technology overcomes these challenges by multiple deck screen design and use of wear resistant urethane materials for panel construction (Kelley, 2007; Valine and Wennen, 2002). For a example, the Derrick screen’s material of construction is a tensionable urethane that provide high open area ranging between 35 to 45% with considerably reduced blinding (Valine and Wennen, 2002). Thus, there has been an increased uptake by the mining industry in the use of wet fine vibrating screens closing the ball mill as the final classification stage in the comminution circuit (Barkhuysen et al., 2010; Frausto, Ballantyne et al. 2017; Pelevin and Lazebnaya, 2009; Teknikk, 2009). Even though there is a number of models in existence, none of these models adequately predict the performance of high frequency vibrating screens (Karra, 1979; Rogers, 1982; Subasinghe et al., 1990; Trumic and Magdalinovic, 2011). Recently Mwale et al., (2016) developed a model for predicting the performance of high frequency vibrating screens using the partition curve properties. The input parameters of the model include screen open area (??) in m2, tonnage feed rate (????) (tph) and the weight fraction of solids (??) in the feed for a given panel aperture size. The model was developed based on data collected from a single deck industrial size derrick screen, in a pilot setup. The work presented in this paper is an attempt to test this model using data collected from Minera Saucito concentrator, an industrial plant whose comminution circuit is shown in Figure."

Jan 1, 2018

By Anuttam Patra, Romain Bordes, Andreas Fredriksson, Tommy Karlkvist, Krister Holmberg, Kota Hanumantha Rao

The present investigation aims to develop and distinguish mineral specific reagents with two functional groups for use in flotation of calcium containing minerals. For this purpose, a series of dicarboxylate-based surfactants with varying length between the carboxylate groups (one, two or three methylene groups) were synthesized. As reference, a surfactant with the same alkyl chain length but with only one carboxylate group in the polar part was synthesized. The adsorption behavior of these new reagents on pure apatite and calcite mineral surfaces was studied using Hallimond tube flotation, FTIR and ? potential measurements. The relation between the adsorption behavior of a given surfactant on a specific mineral surface and its molecular structure over a range of concentration and pH values, as well as the region of maximum recovery were established. It was found that one of the reagents, with a specific distance between the carboxylate groups, was much more selective for a particular mineral surface than the other homologues synthesized. This selective adsorption of a given surfactant to a particular mineral surface relative to other mineral surfaces as evidenced in flotation studies is substantiated by ? potential and infra-red spectroscopy data.

Jan 1, 2014

By J. Sachweh

The last few years have shown a significant increase in the demands for fine products, which means everything under 10µm. There are more and more applications requesting extremely fine ground powders leading to the development of several milling machines which are better adapted to the new products. Cost saving machinery is important for the worldwide competition. Especially the energy consumption is extremely important for any fine ground product. A worthwhile field for mechanical engineering companies is the dry milling machinery as there are not as many solutions available compared with wet milling applications. In many cases wet mil-ling is the only solution to reach the requested quality, but there are also a lot of applications which can be performed in a dry way on the premise that the right mill and classifier are available. Dry milling permits to save energy and allows to influence the particle size distribution more easily, as a classifier can be used in that case. This will significantly reduce production costs and can enable the production of new products with better properties. The Tower Mill is well-known already in the field of wet grinding. Recent research work and end user reports have shown clearly that this mill has a lot of advantages compared to a ball mill. Up to now this advantage is limited to wet grinding as only few mills have been used for dry grinding. There is no doubt about the efficiency of dry grinding, but new and improved feeding and discharg-ing systems have to be developed in order to enable the full range of its advantages. Especially the high production capacities are a challenge for mill and classifier designers. The Tower Mill with its special grinding mechanism allows to cope with very high feed rates, because machines with more than 1 MW are available. Improved grinding efficiency will decrease the circulation load through the classifier and also lead to smaller classifier sizes. Together with im-proved mills the classifier can work more efficiently because the feed material is finer. Results of a test center plant production will be shown together with a comparison between stan-dard machinery and the MaxxMill®. Preferential applications for each mill will be explained.

Jan 1, 2014

By Megan Becker, Cyril O’Connor, Jenny Wiese, Gaynor Yorath

The effect of particle shape on true flotation has been widely reported. The present paper presents results obtained in investigating the effect of particle shape on the entrainment of particles during the flotation process. Different hydrophilic minerals with particles of varying aspect ratios were used and their shape determined using rheological tests and QEMSCAN. Their entrainment properties showed a close relationship to their shape with the recovery due to entrainment increasing as the aspect ratio of the particles increased. The effect of surface charge, by changing pH, and size of particles showed that the effect of shape was sustained at different pHs and particle sizes. Proposals are made to explain these observations in terms of the known relationships between drag coefficients and terminal velocities and shape. Since it has been previously reported that different milling procedures can affect particle shape, these results indicate that it is possible that such different procedures may result in increased entrainment of hydrophilic minerals.

Jan 1, 2014

By H. Gallardo, J. Yianatos

Flotation is a separation process in which mineral recovery depends on the particle surface properties. The selective collection of particles by air bubbles requires hydrophobic mineral surfaces. Hydrophobicity can be selectively induced on a valuable mineral surface by means of reagents. For this purpose, it is required that mineral grains in the ore become physically liberated or exposed in the particle surface after grinding. The grinding process generates three types of particles according their exposed surface in the floatable mineral: locked particles (0-10%), associated particles (10-90%) and liberated particles (90-100%). Locked particles have low floatability, and they typically show low recovery (<20%), while liberated particles have a high floatability and can be easily recovered (98-100%) at different particle sizes (10-150 µm). The main challenge in the flotation process is the recovery of associated particles. These particles typically have recoveries of 20-80%, but strongly depend on the particle size, particle surface liberation and collector dosage. Recent studies on particle floatability by size-liberation have significantly contributed to improving the characterization of flotation processes. In this work, a study of flotation recovery of associated particles of 10-90% liberation is presented for particle sizes (10-150 µm) and collector dosages (5-40 g/ton). In this work historical data on galena recovery based on particle cross-section composition of galena was used, assuming they represent an acceptable estimate of particle surface composition, as shown by some previous researchers. The results showed that galena recovery can be well represented by a model consisting of the interaction of a linear function and a Gamma distribution function to account for the liberation and the particle size effects. Consequently, an alternative approach for modelling the recovery of associated mineral (10-90% liberation), with a reduced number of parameters, was developed and validated.

Jan 1, 2018

By F. Xie

Low gold and silver leaching kinetics has been commonly observed in traditional gold-silver cyanidation process, especially in those heap-leaching operations. The reactivity and availability of oxidant was believed to be the critical limitation for gold and silver dissolution. The occurrence of silver sulfide such as acanthite (Ag2S) in the ore may also result in low overall silver extraction. Leaching of gold and silver sulfide in the ferricyanide-cyanide solution has been investigated through rotating disc tests and the assistant effect of ferricyanide on increasing the dissolution rate of gold and silver was noticed. The potential use of ferricyanide as an auxiliary oxidant in gold/silver cyanidation process was proposed based on the results of leaching of gold-silver ores.

Jan 1, 2014

By M. H. Moys, H. Dong

"Discrete Element Method (DEM) has become a standard tool to simulate grinding mills in order to gain information about load behaviour, power drawn, etc. However, parameters necessary to run a simulation are not always readily available. For example, the coefficient of restitution used in DEM simulation from the literature ranges from 0.1 to 0.9 due to lack of accurate values. The lack of correct input parameters results in the fact that some simulation parameters are adjusted to match the simulation prediction with the experimental results. It is inappropriate to tune one single parameter arbitrarily in order to fit the prediction with experimental results. The correct value of parameters for DEM simulation should be established, and rigorous validation on simulation results by DEM needs to be done.The objectives of the ongoing project are to measure the coefficient of restitution at conditions analogous to grinding practice. Equipment has been built to measure the coefficient of restitution. A typical case of impact test showing the vertical position of a ball as a function of time is presented in Figure 1. The coefficient of restitution between steel ball of different sizes and the targets including steel liner (e = 0.91), mild steel block (e = 0.57) and rubber liner (e = 0.7) have been measured. The coefficient of restitution reduces to 0.38-0.52 when there is a layer of coal particles (1-2 mm) on the steel liner. The effects of ball size, drop height on coefficient of restitution are investigated. Then a DEM code is developed of several contact models to simulate the impact process. This code can reveal details on velocities (translational and rotational) and forces (normal and tangential) during the brief impact interval. Figure 2 is a comparison of the rebound rotational velocity between experiment and prediction by different models. The results can be used as DEM input and to assess contact models."

Jan 1, 2003

By Ashton M. Swartbooi, Robert van Hille, Alison E. Lewis

"Nickel production by precipitation using hydrogen reduction generates an ammonium sulphate solution containing approximately 2g/L of nickel, and 1g/L of cobalt as an impurity of the process. Sulphide precipitation is an effective method for heavy metal removal, especially when compared to hydroxide processes: metals can be removed from solution at relatively low pH levels, small quantities of sludge are formed, and due to the high reactivity of sulphides the reactor retention time is reduced. However, the low solubility of sulphide species can lead to spontaneous nucleation of fines (due to higher supersaturation levels which are difficult to separate from solution, leading to reduced process efficiency. Using a fluidised bed reactor, fines formation can be minimised as the pellets provide a large surface area and promote heterogeneous nucleation.A synthetic nickel-cobalt ammonium sulphate solution was reacted with two forms of sulphide reagent: (a) a liquid sulphide solution and (b) gaseous hydrogen sulphide. A range of factors (including pH, reagent concentrations, metal to sulphide molar ratio, flow rates and recirculation rates) influencing the efficiency of the precipitation reaction have been studied. The efficiency of the precipitation reaction was measured using both metal recovery and fines formation as indicators.Figure 1 shows the effect of decreasing the metal:sulphide ratio (at constant SS = 2.725e+17), on the metal removal for liquid sulphide. By decreasing the metal:sulphide ratio, up to 99% removal of both nickel and cobalt could be achieved.These results also indicate that the precipitates that formed were polysulphides, since no sulphide was present in solution after the experiment. This would also indicate that a lower metal:sulphide ratio would be more favourable. However, decreasing this ratio (at constant metal concentrations) would lead to an increase in the fines concentration, because of increased supersaturation levels induced by the higher sulphide concentrations. To decrease the supersaturation, dilute solutions of either reagent would be employed."

Jan 1, 2003

By P. Saha, D. M. Chakrabarti, National Metallurgical Laboratory, P. Bhattacharyya, B. R. Sarkhel

The estimated reserve of the phosphatic soils at the Sukulu hills region of Uganda upto a depth of 60 meters is of the order of 200 million tonnes and analyses 10-12% P2O5. A 5-tonne sample of the phosphatic soil was received at the National Metallurgical Laboratory (NML), India for beneficiation studies. The ore occurred as a naturally degraded soil deposit and the slime contained earthy lateritic minerals which made it extremely sticky. Microscopic examination revealed the presence of limonite, magnetite (martitised), hematite and goethite as major minerals along with apatite and quartz. Presence of clay was indicated by earthy smell on moistening the sample. It was observed that getting rid of the slime was as important for adequate beneficiation of the ore, as it was difficult. Earlier studies on samples of the same ore at the NML and abroad established that it was necessary to pass the ore through a series of three stages of desliming, each consisting of a step of rigorous attrition scrubbing followed by hydrocycloning, for effective elimination of the sticky slimy coating which stubbornly adhered to mineral grains. Studies were carried out at the NML in two phases to develop a flowsheet for beneficiation of the phosphatic soil. In the first phase, reproducibility of the results obtained by employing a flowsheet developed abroad was confirmed along with suggesting some modifications of the flowsheet. Then 200 kg. of concentrate was produced following the recommended flowsheet for evaluation of its suitability for production of fertilisers. To remove the limonitic slimy coating, which stubbornly adheres to the other mineral grains, it was necessary to subject the ROM ore, after screening out the +840 micron size fraction which contained only 1.75% P2O5 , to three stages of hydrocycloning each preceded by attrition scrubbing. Then only conventional beneficiation techniques could be effectively employed to upgrade the ore.

Jan 1, 2003

By Peter J. Coghill, Michael J. Millen, Brian D. Sowerby, Kirby D. Cunningham

"CSIRO Minerals has developed an integrated particle size analysis system for deployment in the grinding circuits of minerals processing plants. The system includes a slurry sampling station, a de-aeration tank and an ultrasonic particle size analyser (UltraPS). The UltraPS analyser is based on ultrasonic attenuation and velocity spectrometry combined with gamma-ray transmission. The technology is applicable to the measurement of 0.1 to 1000 µm diameter particles directly in highly concentrated slurries without dilution. The analyser incorporates a gamma-ray transmission gauge utilising an ultra-low activity radioisotope source that is exempt from International Atomic Energy Agency (IAEA) and Australian licensing regulations.The UltraPS analyser consists of a submersible probe and an electronics package. The probe can be immersed directly in a minerals processing plant stream if the aeration level in the stream is low. For applications where a de-aerated slurry stream is not available, CSIRO has developed an integrated system that includes a sampling station, a de-aeration tank as well as the UltraPS analyser itself. A schematic drawing of the continuous flow gravity fed system is shown in the figure. A commercial sampling system is used to supply slurry at a rate of 2.5m3/hr to the deaeration tank. The aim of the de-aeration tank is to remove air in the slurry to a level where meaningful particle size measurements can be performed. The tank volume is about 0.2m3, thus giving the slurry flowing through the tank a mean residence time in the tank of approximately five minutes. Tests at a number of concentrators have shown that five minutes is sufficient time for slurry to de-aerate to a level where ultrasonic measurements can be made. The tank incorporates an ultrasonic level detection sensor and flow to the deaeration tank is adjusted based on the level of slurry within the tank. The UltraPS probe is mounted through a flanged section of duct, which is bolted to the bottom of the de-aeration tank."

Jan 1, 2003

By Fu Ping-Hao, Sergio Mauricio Vianna, Ewen Silvester, Emmy V. Manlapig

"Over the last 5 years, an ambitious project has been undertaken at the Julius Kruttschnitt Mineral Research Centre (JKMRC) aiming to isolate, study and, if possible, model the effect of particle size, liberation and collector adsorption density on the floatability of mineral particles. As part of this project, we have conducted highly controlled flotation test-work, combined with state-of-the-art solution and surface analytical techniques such as High Performance Liquid Chromatography (HPLC), Time of Flight Secondary Ion Mass Spectroscopy (TOF-SIMS) and detailed mineralogical analysis to fully characterize the flotation behavior of a natural ore.The flotation tests were undertaken using a high-grade lead-zinc ore from BHP-Billiton’s Cannington mine (Australia) in a specially designed continuously operated laboratory scale flotation rig. Solution and adsorbed collector concentrations were measured independently during the course of the flotation tests using HPLC based ex-situ techniques. Liberation studies were performed using the JKMRC Mineral Liberation Analyser (MLA) on selected size intervals of different streams to estimate the specific surface area of galena. These results were used to calculate the collector adsorption density (collector coverage) on galena particles, with the eventual aim of developing a mathematical model describing the relationship between pulp chemistry, feed mineralogy, and floatability of galena particles."

Jan 1, 2003

By B. McFadzean, J. Taguta

The enthalpy of immersion is the heat change arising from the replacement of the solid-gas interface with the solid-liquid interface when a solid surface is immersed in a liquid. Although immersion calorimetry has been established as a valuable and reliable means of determining solid surface properties such as wettability, it has seldom been applied in mineral processing research. In this study, precision solution calorimetry was employed to measure the enthalpies of immersion of different minerals in water. The enthalpies of immersion were then related to the first-order flotation rate constant as determined by the microflotation technique. The same measurements were also made on sulphide minerals whose surfaces were modified to different degrees of hydrophobicity using different percentage coverages of amyl xanthate collector. The enthalpy of immersion technique was capable of distinguishing and ranking minerals according to their wettability. All mineral types and collector-treated minerals conformed to the same relationship that was found between the enthalpy of immersion and the flotation rate constant. This conformed, empirically, to a power law equation. As the enthalpy of immersion decreased, there were large increases in flotation response for very small changes in hydrophobicity. In addition, a critical enthalpy of immersion (CEI) was found, above which no flotation could occur. The scatter in the data points could be corrected for by adjusting the rate constant using the density of the minerals to produce a robust relationship between the rate constant and enthalpy of immersion. These results have shown that the enthalpy of immersion is able to indicate both the natural mineral hydrophobicity and the extent to which collectors can render a mineral hydrophobic. This technique has considerable potential to be used as a sensitive and accurate measure of mineral surface wettability in order to predict flotation performance.

Jan 1, 2018