Search Documents

By C. E. Baltzer

This is the fourth in a series of coal technology reviews being prepared. in accordance with a recommendation voted by the Coal Division C.I.M. in session at the Jubilee Meeting, Vancouver, 1948, that the Department of Mines and Resources be requested to arrange for publication by the proper Government authority of a Quarterly Review of Coal Technology for distribution among those concerned in the production and use of coal in Canada. Copies of the first review, which appeared in the November, 1948, BULLETIN, pp. 612-614, of the second review in the June, 1949, BULLETIN, pp. 272-275, and of the third review in April, 1950, BUL-LETIN, pp. 1,9?3-196 (also, respectively, in Transactions, Vol. LI, 1948, pp. 262-264 Vol. LU, 1949, pp. 117-120, and Vol: LIU, 1950, pp. 133-136), were distributed by the Dominion Coal Board and are still available on request. In this review, the first in the series in the field of combustion, development and trends during the period approximately from World War II to the present time are described and therefore the presentation is general. Later reviews will particularize developments in relation to the range of coals available in Canada.-ED. INTRODUCTION THE utilization of coal in heat and power producing equipment has become of paramount importance to the coal industry in maintaining stable and profitable markets. In the past, the chief concern was with mining, transportation, and overall supply problems, but modern conditions demand interest in and knowledge of all phases of the product, from coal in situ to its ultimate disappearance in the form of products of combustion. Even the last mentoined factor has caused complications, as is shown by current widespread activity in the field of smoke abatement

Jan 1, 1951

By Brigitte J. Dejou

The Red Dog sediment-hosted zinc-lead deposit is located in the Brooks Range thrust belt in northwest Alaska, approximately 1000 km northwest of Anchorage. The mine constitutes the primary deposit in a 400 square kilometre district, which hosts several other mineral occurrences. All the known mineralisation is hosted by the Mississippian Ikalukrok Member, deep basinal shale of the Kuna Formation, part of a Devonian to Cretaceous sedimentary sequence. The rocks underwent intense deformation during the Brookian Orogeny in Middle Cretaceous time. Several thrust faults juxtapose the stratigraphy. The Red Dog mine is composed of four deposits which together contain 105 Mt in resources and reserves for a total resource exceeding 18 Mt of Zn metal. The mine is an open pit with 25 foot high benches. The biggest challenge is not the Arctic conditions, but metal extraction, due to the fine grained nature of the mineralisation and the variability of the ore. The mine produces Zn and Pb-Ag concentrates that are shipped to smelters around the world from the Red Dog port facilities during the short summer period. Ore mineralogy is generally simple and consists of sphalerite, pyrite, galena and marcasite. The deposits are generally overlain by decametre thick exhalative barite horizons and exhibit strong silicification, which locally obliterates the original textures. Although described as a world class Sedex-type deposit, a large portion of the mineralisation exhibits sub-surface replacement textures. Moreover, unlike most other Sedex deposits, the reconstruction of the basin is made difficult by the structural complexity of the district. To assist exploration in the district, several assumptions are made regarding the deposit settings relative to metal source, growth faults or crustal extension.

May 1, 2006

By Bill Mercer

The Triggers for PDAC Involvement in H&S ??Increase in serious accidents in mineral exploration in past few years ??Increasing junior role in exploration ?? Impression that there were few H&S protocols in place in smaller companies ??Lack of national benchmarking ?? The attitude that H&S is a provincial responsibility ??Corporate Social Responsibility initiative What is the issue in exploration? ??Mining?s reputation as ?dirty and dangerous? ??In public?s and media?s minds exploration employees are ?miners? ??In Canada, regulators often do not distinguish between ?exploration? and ?mining?. ??How does exploration compare to mining from a H&S point of view?

May 1, 2008

By P. G. Claridge, R. A. Tenbergen

"Pipe Open Pit ore is delivered by rail to the Thompson Mill at a rate of 34,000 tons per week. Ore is milled at a rate of 220 tons per hour.Characteristics of the serpentinised peridotite host rock are such that significant deviations from hitherto experienced milling practice became a necessity because of coagulation of the gangue upon cominution.Extensive development work was done in the grinding and classification circuits to better understand the ore characteristics and optimize operating parameters and the use of available equipment. This work ultimately resulted in the change from 30 to 20-inch diameter cyclones.Coagulation of the ore slurry and the characterstics of the sulfide minerals necessitated an ""unconventional approach"" in processing as compared with the beneficiation of Thompson Mine ore.Recent changes in ore characteristics led to testing of antistatic agents to reduce tailing losses."

Jan 1, 1975

By Marc C. Bétournay

A mine production locomotive, the world?s first applied industrial fuelcell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuelcell vehicles. The locomotive?s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuelcell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery-powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuelcell vehicles, and cost-benefit aspects. This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable and efficient power plant which fulfilled its design objectives, including longer productivity time for a given vehicle fill-up.

May 1, 2003

By K. V. Konigsmann

"Mattagami Lake Mines Ltd operate a zinc-copper mine with an annual output of about 200,000 tons of zinc and 30,000 tons of copper concentrates. Zinc concentrates arc shipped to a company owned smelter in Valleyfield (a distance of 690 miles), for Export to Quebec City and also to Josephtown, Pennsylvania (1,060 miles, Figure 1.)The protection of concentrates in open gondola rail shipments has been a matter of concern since operations commenced. Considerable financial losses did occur at times because of wind erosion. Operating difficulties were also encountered by customers because of excessive moisture accummulation in the concentrates. Test shipments made in 1969 established the magnitude of losses in open cars. The results and subsequent investigations at our mines and elsewhere confirmed that load protection is an economic necessity.Many types of covers were experimented with, more or less successfully. In 1972 we agreed on a joint program with Dupont of Canada Limited. A new type of cover was developed by early 1973. It has been in use since, undergoing several improvements as experience accumulates."

Jan 1, 1975

By Peter A. Oshust

The EKATI Diamond Mine has successfully completed the development and commissioning of the Panda Underground Project to extract the ore below the Panda open pit. The dominant kimberlite domain of the Panda Underground, intermixed olivine-rich and mud-rich resedimented volcaniclastic kimberlite (RVK), is very similar to the kimberlite domain characterizing the open pit portion of the pipe. A sublevel retreat mining method is in operation underground at Panda; near-vertical blast rings are drilled and blasted into an open void. Broken ore is mucked with load, haul and dump trucks (LHD?s), sized underground then moved to surface through a conveyor system to the process plant. An advanced feasibility study is in progress at the Koala Underground Project. The Koala pipe is geologically more complex than Panda. The pipe below the open pit is comprised of at least five distinct kimberlite domains. There is a 100 m thick zone of incompetent low-grade mud-rich RVK between the open pit and the stable high-grade olivine-rich primary volcaniclastic kimberlite where mining will be initiated. As a result, it is proposed that Koala will employ sublevel caving; each blast ring shot would be confined and mucked in sequence to maintain the cave of the over-lying low-grade RVK ore. The sublevel cave method seeks to safely defer the mucking of the low grade ore to the latter part of the mine life.

May 1, 2006

By G. K. Quainoo

In the automotive industry, the awareness to meet Corporate Average Fuel Efficiency (CAFE) standards has evolved the need to reduce vehicular weight in new automobile designs, with the overall goal of reducing gas emissions into the atmosphere (Kyoto protocol), One efficient method has been to use lighter materials such as aluminum in outer body panels, Heat treatable AA6111 is one of the materials employed due to its unique combination of formability, paint bake strengthening and superior corrosion resistance characteristics, Researchers have applied various thermo-mechanical processes on 6000 series aluminum alloys and have found an improvement in the mechanical properties of these alloys, For a formed and painted automobile panel, the final mechanical properties involve a combination of strength components arising from cold work, strain aging and precipitation minus recovery. In this study, the evolution of microstructure resulting from the interaction of cold work and precipitation in AA6111 has been studied by means of transmission electron microscopy (TEM) after subjecting samples to various heat treatments, tensile testing and differential scanning calorimetry (DSC), This has been done to understand the evolution of microstructure and its influence on the properties of the alloy, The results show a considerable improvement in strength with a corresponding increase in strengthening precipitates with increasing level of cold work in the alloy. DSC results following the application of various levels of cold work also show acceleration in the precipitate phase formation, as precipitates are observed to form at lower temperatures, with increasing level of cold work/

Jan 1, 2005

By M. W. Lewis

A mine's inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine ’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By M. W. Lewis, B. Sambirsky, J. Werner

A mine’s inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By Frank G. Wickert

One key to maintaining successful mining operations in today?s global economy is in having the ability to access real-time machine operating data ([1] G. Brown, B. Ebacher, W. Koellner,2000)([2] Brochure of Siemens E&A, Order Number 141000-1). With recent and ongoing advances in mining equipment systems it is imperative that mine managers have full knowledge of the status of their equipment at any given point in time. This knowledge is critical to ensuring that the productivity of each and every machine is maximized. Knowledge of machine status is only the first step, however, in controlling and optimizing a piece of mining equipment. Computer based diagnostic systems, traditionally offered on mining equipment, have provided a link for collecting data and trouble-shooting problems as they occur. One problem existed, though, that those systems stopped short of providing full drive systems access. A maintenance technician could see the data but to make critical adjustments or make repairs the technician needed to be on the machine. In extreme cases the machine would be down until OEM assistance could reach the mine site. The key then to reducing down-time and maximizing machine productivity was creating a system that could not only monitor drive systems but also provide remote access to those systems. Essentially a link needed to be created through which a technician could gain drive access remotely then make adjustments or repairs without being on the piece of equipment. This paper will introduce AccessDirectTM, a new remote diagnostic system for Bucyrus mining shovels and draglines. AccessDirectTM combines all three important elements of remote diagnostics: ? Vital Signs and Production Monitoring (SiRAS-M) ? Automatic analysis (SiRAS-A) of faults, and tracking of trends for preventive and reliability centered maintenance , and ? Fast, direct Intervention (SiRAS ? I) for troubleshooting support, repairs, and system optimization.

May 1, 2002

By Yves Breau, François Robichaud, Jacques McMullen, Pierre Pelletie

"The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.INTRODUCTIONThe East-Malartic mill is located close to the town of Malartic in North Western Quebec, Canada. The mill was first commissioned in 1938. The flowsheet at that time was a straight cyanidation circuit. The original mill operated in that mode up to the discovery of the Bousquet 2 orebody in 1989 which consisted of a massive copper sulphide ore averaging 0.7% copper and 7 g/mt of gold. Bousquet 2 ore processing required a mill retrofit. Grinding capacity, gravity and copper flotation circuits were inserted prior to the cyanidation circuit in order to achieve 3,200 mtpd capacity at expected recoveries.In 1993, control of the flotation circuit was deemed critical in order to maintain the flotation performance and to reduce cyanide consumption since the copper sulphide contained in the Bousquet 2 ore is a high cyanide consumer (50% bornite). (McMullen, 1999) As a result, the implementation of advanced control strategies in order to increase the metallurgical profitability of the plant and to reduce the operating variability between operators was the most rational alternative. In 1994, Corem was chosen to perform the plant audit and to write the first set of rules. The on-line control strategy was started up in 1995. In 1996 and 1997 the Expert System was shutdown because of an extreme change in the ore coming from the milling of Bousquet #1 ore and the departure of the projects engineer. In 1998, the system was restarted and the results were impressive. Furthermore in May of 2001 a patent was issued for the control strategy. (Breau, 2001)"

Jan 1, 2002

By Jose R. Hernandez-Aguilar

"Three models to predict the effect of bubble size (Db) on metallurgical response were tested in a pilot-scale flotation column at Teck Highland Valley Copper mine. The column was fed with slurry collected from the Cu/Mo separation circuit. The first model was the one developed by Gorain et al. (1997), which assumes that the collection zone rate constant (kc) is inversely proportional to Db. The second model was the one proposed by Hernandez-Aguilar et al. (2010), which considers kc as an inverse square function of Db. The third model was the one developed by Yoon and Luttrell (1989) which provides expressions to describe the efficiency of particle collection (E) based on first principles. The results showed a significant bias between experimental and predicted data using the model of Gorain et al. (1997), possibly reflecting the model’s inability to explain the impact of bubble size, bubble rise velocity and flow regime on E. The model of Hernandez-Aguilar et al. (2010) well described the experimental evidence. The model of Yoon and Luttrell gave accurate and unbiased predictions. However, Yoon and Luttrell’s approach calls for a criterion to determine whether the flow regime is potential or intermediate, a subject that requires more fundamental research.INTRODUCTIONParticle collection, i.e., bubble-particle collision followed by attachment, is the basis of flotation. In a quiescent environment (such as the one observed in a column, or away from the impeller in a mechanical cell), a collision event can take place as long as the “degree of turbulence” caused by the rising bubble does not prevent particle and bubble to flow in close proximity. Upon collision, the particle slides on the bubble surface for a period of time. If the particle is hydrophobic, attachment occurs when the “sliding time” is longer than the “induction time”, which is the time required to thin and rupture the intervening liquid (usually water) film forming a three-phase contact angle. While the induction time is largely influenced by the degree of hydrophobicity of the particle, the degree of turbulence is governed by the bubble size. Generally, direct control of bubble size is not exercised by most mineral processing practitioners, in spite of its obvious importance. Studies to model the effect of bubble size on particle collection using fundamental approaches have been conducted (e.g., Anfruns and Kitchener, 1977; Webber and Paddock, 1983; Yoon and Luttrell, 1989; Dai et al., 1999). However, these models have been validated under highly idealized laboratory conditions (micro-scale experiments using single minerals and uni-sized bubbles), far from resembling those existing in practical industrial applications. Fundamental studies to interpret the effect of bubble size on particle collection in industrial environments are largely absent in the literature. Partly because of this lack of practical knowledge, many mineral processing practitioners perceive laboratory “bubble size” studies to be valuable academic exercises, but not something that can be directly applied to daily production issues."

Jan 1, 2011

By Gordon F. Scott

This paper considers a recently completed hoist project for IAMGOLD. Called the Westwood project, this mine utilises some of the largest drum hoists supplied to the North American Market in recent times. This project is an example of where many of the design features discussed the associated paper, (Robotham, 2011) were incorporated. Director of sales and marketing, Gordon Scott has worked at DavyMarkham for over 30 years in a variety of roles starting as a mechanical design engineer, moving to project management before joining the sales department. Gordon has an honours degree in mechanical engineering from Leeds University.

May 1, 2011

By Éric Létoumeau, Julie Fournier, Sylvain Caron, Yves Breau, Martin Plante, Dominique Girard, Luc Tardif, François Robichaud

"Since 1999, COREM (formerly the Centre de Recherche Minérale) has conducted and coordinated research and development activities for a consortium of mining companies that uses the benefits and advantages of collaborative pre-competitive research. In particular, COREM’s “In Situ Optimization Group” is involved in the development and implementation of modem information technologies related to process optimization and control.The POP Project was launched in order to increase and consolidate the use of such technologies applied to mineralurgical and metallurgical processes. To ensure a successful transfer to the industry, there are a number of essential activities that have to be undertaken. These activities have been identified by COREM’s members and are grouped into three main modules:- R&D Module: research and development in universities and research centres;-Technology Transfer Module: integration of new tools into the POP Software, industrial applications and technical support;- Training Module: education of new engineers in universities and continuing education of plant personnel through on-site workshops.This paper outlines the opportunities that led to the definition of the POP Project, presents its main objectives and describes its main modules. The main features of the POP Software are outlined, the first applications at COREM’s member plants are presented and, finally, future developments are discussed."

Jan 1, 2002

By Mark Rebagliati, John Payne, Jim Oliver

The Campo Morado precious-metal-bearing, volcanogenic massive sul?de deposits occurin a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt inthe Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic ?ows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sand-stone. The Reforma and El Rey massive sul?de deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sul?de deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sul?de occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, andCu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite,chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Goldand Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sul?de for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic foot-wall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sul?dation, volcanogenic massive sul?de system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By Mark Rebagliati, John Payne, Jim Oliver

Abstract-The Campo Morado precious-metal-bearing, volcanogenic massive sulfide deposits occur in a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt in the Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic flows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sandstone. The Reforma and El Rey massive sulfide deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sulfide deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sulfide occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, and Cu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite, chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Gold and Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sulfide for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic footwall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sulfidation, volcanogenic massive sulfide system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By K. Wyper

"Gulf Minerals (Canada) Limited' s Rabbit Lake Uranium Operation is located in the northern portion of Saskatchewan, 198 miles southeast of Uranium City and 134 miles northwest of Lynn Lake Manitoba.This paper describes flow sheet changes to solve operating problems and briefly describes future changes to accommodate the new ""B"" Zone ore.The Rabbit Lake mill was designed to process 1600 dry tons per day of uranium ore, with an average grade of 0.370 percent u3o8. In 1981, the mill processed 2040 tons per day at a grade of 0.231 percent u3o8 . The process modifications and flow sheet changes that allowed this increase in tonnage will be discussed in relative chronological order. Mill feed was introduced on June 10, 1975, the original equipment consisted of an Ingersoll Rand hydraulic breaker mounted over a 24"" square grizzly. The - 24"" ore was fed to a 2011 X 6"" seflli autogenous grate discharge mill close circuited with 20"" cyclones, the mill discharge was screened on a tyler double deck screen with the undersize (8 rnesh) reporting to the cyclones, the screen oversize was returned by conveyor belt to the mill feed chute.The cyclone overflow (28 mesh) was thickened in a 100' diameter thickener to obtain 55 percent solids for the leach circuit.The leach circuit consisted of two slurry holding tanks and five leach tanks."

Jan 1, 1982

By J. D. Jorgenson

?? U.S. domestic production peaked at 120 Mt during years of the Korean Conflict120 Conflict ?? Pellet production increased, as highPellet high-grade ores decreasedores decreased ?? Until 1982 recession, most U.S. iron ore mines owned by steel companiesmines companies ?? Large Canadian iron ore mines brought into production after 1950into 1950

May 1, 2011

By R. H. Beaton

"About 1905, a plant was constructed at C1ayburn, in the Lower Fraser valley, 4'5 miles east of Vancouver, to process shales from Sumas mountain into heavy clay products. In time, mining operations were found to be more favourable on the opposite side of the mountain, and by 1913 a plant, which soon became the centre of activities, was completed at Kilgard. Destroyed by fire in 1949, the plant was rebuilt on modern lines, and a second plant was established at Abbotsford, six miles to the west. The Company, from its beginning, has grown with development of the Province. In recent years, operations have kept abreast of latest developments, particularly in materials handling. Latest innovation has been the complete conversion of fuel from Bunker C oil to natural gas. In 1957 the Company became associated with Harbison Walker Refractories, Limited, a leader in its field in the United States, and its title was changed from Clayburn Company, Limited, to Clayburn-Harbison, Limited. Currently, the Kilgard plant produces sewer pipe, agricultural tile, and flue liner; the Abbotsford plant, refractories and facebrick. Improvement of products and development of new ones are tasks of a recently-completed testing and research laboratory.Almost all ware produced is marketed in Western Canada or Washing-ton State. The Vancouver area absorbs the bulk of structural clay products."

Jan 1, 1959