Search Documents

By B. A. Watters, G. A. Parslow, F. H. Mcdougall

Carbonate-rich rocks occur at several localities within the Flin Flon volcanic sequence of the eastern Amisk Lake area. The rocks occur in two areas: as a group of small occurrences on islands within Amisk Lake and as two much larger linear belts running parallel to the regional structure east of Amisk Lake. Mineralogically, the rocks consist of talc and Ca-poor ankerite with occasional graphite. Segregation of these minerals and colour variation impart a well-defined planar fabric to the rocks and where the units are fairly continuous (e.g. Mosher Lake), their trend and attitude suggests a concordant relationship to the volcanics. Major and trace analysis of22 samples confirms the presence of two types, with one type being represented in each of the two areas. Most of the elements studied can be used to characterize the two groups, but three elements in particular give a clear separation: Mg, AI and Ni. Recalculation of the major element analyses, on a water and carbonate-f ree basis, indicates that one group (large concordant bodies with high MgO, high Ni and low AI20.J is altered ultrabasic material of peridotitic or dunitic composition. Because no relict igneous material is observed, and the contacts are apparently very sharp, it is possible that the hydration-carbonization process occurred simultaneously with intrusion, .in a closed system. The other group (small occurrences with relatively low MgO, low Ni and high AI203J represents alteration of basaltic rocks. AIthough some analyses suggest the introduction of calcium, as carbonate, along with the volatiles, the major oxides have remained remarkably stable during the alteration process(es).

Jan 1, 1981

By G. R. Sadowski

"Large subhorizontal joints have been found in the foundation excavations in basalt and granite of Brazilian Dams. Some spread for hundreds of square meters showed slickensides—polished surfaces plus striations—and laminations interpreted as related to shear displacement, what substantially reduced their shear strength and imposed special reinforcement measures against the potential sliding of overlying concrete structures. The geological characteristics of these discontinuities have raised speculations related to their origin, be it related to mechanisms of bulging, cambering or to some tectonic or primary geological event.Several geologists and engineers from the northern hemisphere including Terzaghi already showed to be concerned with their role in granite foundations while in the southern regions Brazilian authors have found similar occurrences but also affecting individual lava flows of continental flood basalts in the foundations of major dams of the Parana Basin, which they designated under the particular name of “fault-joints”. This double-standard designation is self-explanatory of the difficulties involving their origin and related geomechanical properties: faults or just shear joints?Recently, similar features were encountered in the foundations of large dam constructions in anorogenic granites inserted in the realm of the Brazilian Amazon, where some of these discontinuities exhibit features common to tectonic thrusting combined with deep tropical weathering.The evidence of preshearing along the surfaces of such fractures, also associated to products of deep weathering, reduces their geomechanical strength substantially, suggesting values of ultimate phi spanning 12 to 28°. The detection of these descontinuities during initial investigation phases continues to be a major complex task in geological risk evaluations surveys. Trenching associated to some geophysical exploration techniques, although considered to be very basic exploration techniques are still the suggested methods for their forecast and previous determination."

Jan 1, 2015

By R. J. Mitchell

"Centrifuge modelling of earth structures is a well-proven technique for evaluating the performance of prototype structures using physical models. The applications of this technique have increased dramatically during the last decade such that even the modelling of dynamic responses in structures has been accomplished.This paper presents the first model test results used to design a mine backfill. The models were tested using a 3 m radius 30 g-tonne geotechnical centrifuge which was constructed at Queen's University specifically for model studies on mine backfill stability and subsidence. The models represent the first production blast-hole stope to be mined at Westmin Resources Ltd. 's H. ~ Mine on Vancouver Island. This paper includes photographs of:model failures in the centrifuge and correlations of model test results with analyses based on unconfined and triaxial test data.IntroductionDuring the feasibility study and development stages for the H.W. Mine, Westmin Resources Ltd. conducted a comprehensive rock mechanics and backfill engineering program. The results of these studies indicated the need for assurance of backfill stability during pillar recovery on the initial blast-hole mining block. The cemented tailings backfill had to be free standing for heights up to 25 m and the potential for surcharge loading from a weak hanging wall zone, the potential for fill block sliding down-dip and the potential for seismic loading had to be considered in the design of the fill strength. The basic questions to be answered were: what cement content is required and will the resulting backfill costs be economic relative to the proposed mining method and sequence? Figure I shows a typical cross-section through the first mining block . The up-dip stope is to be mined first and backfilled with cemented tailings . The down-dip stope would then be mined and filled. Depending on ground conditions encountered, the complete intervening pillar could be recovered and the void backfilled with uncemented tailings or it could be recovered in small sections by exposing limited back and wall areas, backfilling with waste rock and I or cemented tailings . This latter method is commonly referred to as the Avoca method"

Jan 1, 1987

By A. L. Holloway, N. M. Soonawala, L. S. Collett

"Since the late 1970s, a major R&D program has been under way in Canada to assess the concept of disposing of nuclear fuel wastes in deep plutonic rock. Atomic Energy of Canada Ltd . (AECL), a federally-owned corporation, has been given the responsibility of directing this research (Rummery et al., 1983).The Underground Research Laboratory (URL), constructed in a granite pluton 15 km east of Lac du Bonnet, Manitoba (Fig. 1) is a major component of the Canadian Nuclear Fuel Waste Management Program. A diverse geotechnical experimental program is being carried out during both the construction and operating phases of the URL. This program involves detailed geological mapping, rock mechanics and hydrogeology studies, and geophysical surveying, to characterize the rock mass surrounding the shaft, and it has been described by Simmons et al. (1983). As part of the construction-phase program, ground-penetrating radar (GPR) surveys are being carried out during excavation, in an attempt to delineate fractures both ahead of the excavation and behind the walls of the excavation. This paper presents the results of surveys performed during shaft excavation and describes a procedure for plotting the data.Ulricksen (1982) cites examples of radar surveys to evaluate surficial deposits, such as peat, sands and gravels, and cavity detection in subsurface hard rock. Fowler (1981) used radar for fracture and clay vein detection in coal seams.In Canada, pioneering work in GPR has been done by Annan and Davis since the mid-seventies (Annan and Davies, 1976). Their work concentrated on problems relating to permafrost in the Arctic ."

Jan 1, 1986

By P. K. Chatterjee

"The operations of a large-scale open-cut mine are simulated to produce a user-oriented interactive digital model. SIMULA is chosen as the programming language and a sophisticated data base system is designed to consider the complex information network of large mines. The main features of the program are the mine planning and mine evaluation modules. These modules are responsible for the computation of truck-shovel performance and other equipment details in a mine. Stochastic methods are employed to generate event times. The use of a Data Base Management System and the data base provide an efficient method of information storage and retrieval. Truck allocation techniques have been examined in detail and comparisons between random dispatching and conventional methods are made. The model is intended for mine operators and engineers and the program is well structured and very readable. It is hoped that these features will make the model readily acceptable.IntroductionThe Department of Mining and Metallurgical Engineering at the University of Queensland has been conducting research into computer simulation methods in mining since 1972. The research has been mainly applied to actual operations, with both open-cut and underground mining being equally emphasized. The results of the research to date have not only strengthened the methodology of the approach to complex mining problems, but have also increased confidence in the use of modelling and computer simulation technique s in mining.The model described in this paper translates a complex LHD situation into a user-oriented interactive digital model using SIMULA. The present methods of evaluating truck dispatching and trolley assist are tedious and laborious. This model provide s the engineer with readily acceptable means of rapidly assessing the relative merits of these techniques in a large-scale open-pit operation. Poor utilization figures in many current operations (for example, 40% for trucks, 70% for shovels) are of serious concern to mine officials and computer-controlled dynamic truck dispatching systems have been considered by some of these mines to improve equipment utilization ."

Jan 1, 1981

By P. W. Udo Graefe

"An interactive computer model of a dragline, windrow and spoil pile has been developed for modelling oil sands mining operations. The model is to be used in conj unction with models of other oil sands mining equipment, such as bucket-wheel excavators and reclaimers, conveyors, hoppers, bins, trucks and shovels, to study mining operations on a minute-by-minute basis. From the orebody description and mining selectivity, layers of ore and reject are determined and mined by the dragline. Reject is dumped on the pit floor; ore is either dumped on a windrow for later removal by a bucket-wheel reclaimer or directly dumped into a hopper feeding a conveyor. The model allows for the presence of pads as a dragline base, key cuts and a number of interruptions to the mining operation such as shift changes, boom checks, engineering services, repairs, delays, preventative maintenance, etc. A CRT display keeps the model operator informed about equipment status and performance. The model operator can direct the course of the simulation by issuing commands to the model at any time during the simulation.IntroductionThis paper describes an interactive computer model of a dragline, windrow and spoil pile. The model was designed by the author based on information and specifications provided by Canstar Oil Sands Ltd. The model design was implemented and tested on Petro-Canda's IBM computer system by DMR and Associates Ltd. of Calgary, Alberta.The model was designed to form three components of an oil sands mining operations model, described in reference I. Figure 1 shows the interaction of those components with the remainder of the oil sands mining model.An ""Ore/Waste Body"" data base provides information to the dragline model about the location and composition of or e and waste in the mine. The dragline model is used to simulate mining this ore/waste body, to build up spoil piles for center reject (waste) and to dump ore onto windrows or hoppers (situated over conveyors) to deliver the ore to the extraction plant. The windrow model component provides a data base which will be used by a model of a bucket-wheel reclaimer which simulates the loading of ore from the windrow on to a conveyor via a bridge."

Jan 1, 1982

By J. E. Dutrizac

A pyritic Zn-Pb-Cu ore waspercolation leached with acidified ferric sulphate solutions; zinc and copper were leached, lead was oxidized, but not dissolved, and pyrtte was essentially unattacked. High zinc extractions were achieved after a few months leaching, and substantial zinc solution concentrations could be produced by recycle of the oxidized solution. The leaching rate was generally controlled by the transport of the ferric sulphate oxidant. Zinc extractions increased with increasingferric ion concentration or flow rate, but were essentially independent of the concentrations of sulphuric acid, ferrous sulphate, cupric sulphate or chloride ion. The leaching rates were insensitive to the height of the ore column once a minimum height had been exceeded (0.8-1.0 m). Elemental sulphur was the principal sulphidic reaction product, but variations in the ratio of sulphur to sulphate produced anomalous temperature effects.

Jan 1, 1979

By J. M. Beeckmans, S. G. Butcher, M. Goransson

"The counter-current fluidized cascade is a novel and potentially efficient pneumatic gravity separation device. Data are presented on over 150 runs of cleaning Alberta thermal coals, covering several size ranges. The coarser sizes of coal were processed in admixture with a fluidizing medium consisting of 0.5-by 0.1-mm hematite (or magnetite) and limestone particles. The partition curves for coal particles larger than about 3 mm, mixed with fluidizing medium, showed that the sharpness of separation achievable with the cascade approaches that of wet heavy medium processes, whereas with particles in the size range of 3 by 0.6 mm the sharpness of separation was comparable to that of a Baum jig. Useful cleaning was also achieved with particles smaller than 0.6 mm , Throughput rates of up to 11 tonnes per metre width of cascade per hour were achieved, with no indication of a deterioration in performance.IntroductionPneumatic coal beneficiation has steadily lost ground vis-a-vis hydraulic beneficiation during the past quarter century, primarily because of the sharper separations achievable with the latter methods. Nevertheless, there are certain inherent advantages of pneumatic separation methods which would give them an advantage in the market place were it possible to increase their efficiency to be technically competitive with those of hydraulic processes. These advantages are a dry product, resulting in a higher calorific value per ton, and avoidance of the problems associated with treatment and storage of process waste waters. Also, although it may be necessary to dry the raw coal prior to pneumatic processing, the dry rejects produced constitute an ideal fuel for a fluidized-bed combustor, which could provide heat both for drying the coal and for other purposes."

Jan 1, 1982

By H. A. Kishawy, S. Kannan, M. Balazinski

Metal Matrix Composites (MMCs) are new generation engineering materials that possess superior physical and mechanical properties compared to nonreinforced alloys. However, the presence of abrasive ceramic reinforcements in the ductile matrix causes severe tool wear and premature tool failure. Flank wear was found to be the dominant wear mode while the main wear mechanism was abrasion. Analysis of the cutting tools using scanning electron microscopy has shown that both two body and three body abrasion are operational during machining MMCs. A methodology for predicting the tool flank wear progression during bar turning ofMMCs was presented in an earlier paper [1]. In the proposed model, the wear volume due to two body and three body abrasion mechanisms was formulated. Then, the flank wear rate was quantified by considering the tool geometry in 3D turning. The main objective of this paper is to investigate the contribution of two body and three body abrasion towards the tool wear volume during cutting MMCs.

Jan 1, 2006

By E. Poiate, P. A. L. P. Firme, D. Roehl, M. A. Carrion, A. M. Costa

Drilling high-pressure/high-temperature wells in salt rock formations is still a challenge for the energy industry. Creep and solubility is part of the salt rock physical-chemical behaviour, which must be considered in the design of the wells. The stress redistribution caused by drilling, in addition to thermallyactivated processes, triggers creep deformation, leading to borehole closure and the imposition of loads on the casing. The drilling fluid is designed by computer modeling in order to control the creep strain rate to a limit which allows the drilling operations and the casing setting. Depending upon the composition of the drilling fluid, chemical reactions on the salt wall may occur, especially in case of water-based fluids in highly soluble salt rocks. In those cases, cavities by dissolution (washouts) can be generated and the casing column remains uncovered by the cementation and laterally unconfined along the cavity length. This scenario is propitious to the loss of integrity of the casing due to phenomena such as plastic collapse, buckling and non-uniform loading on the casing provoked by the closure of salt formation around it. The casing should remain intact during the wellbore life-time. In this work, a section of a typical well crossing salt formation composed by halite and carnallite is considered. An idealized-cylindrical washout cavity inside a highly soluble salt layer is assumed. The purpose here is to evaluate the effect of the dimensions of the cavity on the integrity of the casing. Several typical diameters and lengths of the cavity are adopted. Numerical analyses are carried out with an in-house finite-element system composed by the pre-processor MTOOL 3D®, the simulator ANVEC 3D® and the post-processor POS 3D®. Salt rocks are modeled as visco-elastic materials. Creep is simulated by the Double Mechanism Creep Law, widely employed in Brazilian salt rock mechanics research. Cement and casing (steel) are modeled as elasto-plastic materials described by the Mohr-Coulomb and the von Mises criteria, respectively. Casing integrity is evaluated with respect to vertical and horizontal displacements. Vertical displacements imposed to the casing can provoke the failure of the column by plastic collapse or by buckling. Besides that, horizontal displacements of salt due to creep closure shall lead to the undesirable contact with the casing. Failure envelopes based on displacements are generated. The results of the simulations have shown that the casing failure by plastic collapse occurs preferentially in short columns, as well as buckling occurs in long and slender columns. The occurrence of both failure modes is more frequent in large-diameter cavities. Additionally, failure caused by contact between salt and casing occurs preferentially in short-diameter cavities.

Jan 1, 2015

By Frank Baczek, R. Q. Honaker, D. P. Patil, B. K. Parekh

Fine refuse slurry impoundment is a requirement for the coal industry to dispose the fines. Impoundment maintenance is an on going problem for the coal industry and its breakage creates environmental as well as financial problems. Deep Cone thickener technology which has been successfully applied in the alumina industry to dewater red mud was evaluated for fine refuse slurry. Preliminary obtained in a pilot-plant test showed that properly flocculated conventional thickener underflow slurry could be thickened to about 52.5 wt % solids and could replace belt filter press. The Deep Cone thickener was also found to dewater clean coal slurry to about 70 wt % solids. Further testing of the unit at other coal preparation plant is in progress.

Jan 1, 2004

By J. Xie

In underground coal mining, the potential for an outburst of coal and gas is considered to be one of the major hazards. As such, considerable emphasis is given to understanding and preventing such events. A number of indices are used in the prediction of the outburst in a coal mine. The main indices include initial gas desorption rate, gas pressure, gas content, coal strength, gas flowrate from a borehole drilled in a coal seam, and combinations of the above. Some of these indices are considered to be inadequate, inappropriate or impractical for some coal seam conditions, such as those with soft and friable coal. The Huainan Mining Group (Huainan) in China and the Commonwealth Scientific and Industrial Research Organisation (CSIRO) in Australia have been jointly developing gas content based technologies to predict the risk of the outbursts. One of the major progressive achievements is a new method for determination of outburst gas content threshold values. The method utilizes empirical analyses, numerical modeling, and seam-specific knowledge . This paper describes the method and its application for the #11 Seam at Guqiao mine, Huainan.

Aug 1, 2013

By W. A. Alexander

Introduction In the course of a programme of research on beryllium in progress in these laboratories, knowledge of the recrystallization temperature became necessary. As the information is not available in the literature, the determination of this temperature for metallic beryllium was undertaken. By the reduction of grain size through working and recrystallization and the probable simultaneous induction of preferred orientation, it was hoped to improve the working properties of beryllium at lower temperatures. The recrystallization temperature is usually determined by observing the lowest temperature of annealing at which new crystals are formed in severely cold-worked metal or alloys. This temperature is profoundly influenced by the following factors: the purity of the metal, in the case of an element, or the composition of the alloy; the degree of straining or working; the temperature of straining; the original grain size; and the time held at the annealing temperature. The observed temperature is lowered by higher purity, more severe straining, lower temperature of working, smaller original grain size, and longer time of annealing. Beryllium presents special difficulties in that the percent elongation in tension is effectively zero, so that ordinary squeezing or rolling was not possible. A possible means of straining was suggested by the fact that indentation hardness tests could be made. It was known from earlier work that the metal could be worked at elevated temperatures, so that working at the lowest feasible temperature and quenching might also be a means of producing strain. The purity of the metal is also a point of some uncertainty in the case of beryllium. Losano has prepared 99.96% Be which appears to be the best reported. Distilled metal used in the present work approached this purity. However, by analogy with other metals, residual impurities may have a pronounced effect on the recrystallization. Further purification of beryllium would evidently entail considerable difficulties due to the highly reactive nature of the metal, and was not attempted.

Jan 1, 1947

By R. R. Rogers

Introduction The subject of cathodic protection is not new. In 1824 Sir Humphry Davy, in publishing the results of his investigations for the British navy, pointed out that copper could be protected from sea-water corrosion by connecting it electrically with zinc or iron. Since that time much work has been clone in this field, particularly in the protection of metals from the action of sea water, neutral brines, and treated and untreated waters. Special mention should be made of the successful protection of underground pipe-lines which formerly were badly corroded by the water in the ground. So far, magnesium alloy and zinc anodes have been the most popular. However, fairly recent work has indicated that aluminium anodes will give good service under certain conditions. The principle of cathodic protection has been applied extensively in coating steel articles with zinc and in cladding aluminium alloy sheet with pure aluminium. A valuable discussion of the fundamentals and applications of cathodic protection recently was presented in the Corrosion Handbook. A useful list of references was included in the article.

Jan 1, 1949

By Y. Chino

Cross-rolling, in which the roll axis is tilted by 7.5 degrees against the transverse direction, was carried out on a commercial magnesium alloy. The (0002) texture intensity of the cross-rolled specimen was lower than that of the unidirectionally rolled specimen. Also, the grain size of the cross-rolled specimen was smaller than that of the unidirectionally rolled specimen. As a result of the Erichsen tests at 433 ? 493 K, the press formability of the cross-rolled specimen was higher than that of the unidirectionally rolled specimen. The high formability of the cross-rolled specimen is attributed to both the reduction in (0002) texture intensity and the enhancement of grain refinement by the cross-rolling.

Jan 1, 2006

By Ken Woloschuk

??Owners?Perspective ??Owners?Challenges ??EcoNomics?Delivery Model ??Projects ??Project Outcomes ??Questions ??Balancing the triple bottom line initiative: ?shareholders expectations of economic costs and benefit; ?stakeholders expectations of social and environmental costs and benefits; ?deciding what is sustainable and which design alternatives are the most sustainable. ?? Delivering required project outcomes

May 1, 2008

By K. P. Plucknett, Z. Memarrashidi

WC-Co ‘hard metals’ are widely used in a variety of industrial applications due to their resistance to abrasive wear, in addition to their high hardness and toughness. However, in contrast to their mechanical properties, the corrosion response of these materials is relatively poor. In the current work the corrosion mechanisms of two WC-Co cermets are analysed, with 10 and 30 vol. % of the Co metal binder, in a 3.5 wt.% NaCl aqueous solution. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential, potentiodynamic polarisation and cyclic polarisation, together with systematic analysis of the post-corrosion solution chemistries using inductively coupled plasma optical emission spectroscopy. The corrosion potential and current density were determined, following Tafel extrapolation, allowing the calculation of the corrosion rates. It is demonstrated that continuous dissolution of the cobalt phase occurs during corrosion, which is a result of poor cermet passivation behaviour, and this response increases with the amount of binder in the cermet.

Jan 1, 2015

By B. W. Brooks

"After an extensive period of University research and field trials, large scale reclamation of the Waite Amulet tailings discharge areas commenced in the spring of 1978. The Noranda program consists principally of sampling the complete dam to determine the vegetation potential of the various areas, addition of the required amelioration materials, and the use of good agricultural practices. This paper describes the development work that led to the establishment of the Noranda-Guelph Contract and the subsequent findings concerning the revegetation of tailings dams. Current revegetation procedures are presented. INTRODUCTIONThe Amulet Mine Ltd. was staked in 1924 and by 1930 had constructed a small 300 ton per day flotation plant. During the late twenties and early thirties, Noranda Mines Ltd. increased its equity in the company to gain a sixty percent share of this small mine. In 1933 the mine was amalgamated with another small producer, the Waite Ackerman Montgomery Mine Ltd., which was more than eighty per cent controlled by Noranda to form the Waite Amulet Mines Ltd.An interesting historical side point to the story of the Waite Ackerman Montgomery property is that a concentrator was never constructed. In fact, the first ore to go through the Horne mill of Noranda Mines Ltd., built in 1928, was not from the famous upper H and L ore bodies but custom shipments from the Waite."

Jan 1, 1981

By T. A. Apelt, B. J. Elliot

"In September 1993, the flash furnace at Kalgoorlie Nickel Smelter, KNS, was brought off line after almost 12 years of operation. This is a record campaign life for a flash furnace. The furnace was' totally rebuilt and the capacity of the plant increased from 540 000 tpo to 750 000 tpa of concentrate throughput. The throughput increase was' achieved through the construction of a 525 t/day oxygen plant and upgrading of various plant ancillaries. A number of significant design modifications were also built into the flash furnace and oxygen enrichment was implemented in the operation of the Peirce-Smith converters.This paper discusses the rebuilding of the flash furnace and design modifications made to furnace equipment and ancillary plant. Some preliminary post-startup operating data are presented.IntroductionIn September 1993, Campaign 6 of the flash furnace was concluded and the furnace brought off line for rebuilding. The campaign length was almost 12 years and set a new record for campaign length. Planning for the rebuild took place over the last five years of the campaign. A number of modifications to the design of the furnace and the ancillary plant were planned to coincide with the furnace rebuild. The furnace was rebuilt and recommissioned in 70 days. The increased plant capacity of 750000 tpa has been achieved by the construction of a 525 t/day oxygen plant and modifications made to ancillary plant which centred around increased p~ control, efficiency and hygiene. This paper examines the development and implementation of the modifications made to the furnace and ancillary plant. Preliminary post-shutdown performance data are presented."

Jan 1, 1995

By Å. Partapuoli, M. Henriksson, P. Wikström, J. Worth, G. Adolfsson

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB’s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012