Search Documents

By Neda Zangeneh

Production efficiency from low permeability gas shales require techniques to optimize hydraulic fracture completions. One completion strategy involves the simultaneous or near simultaneous hydraulic fracturing of multiple horizontal wells to maximize the fracture network area and stimulated reservoir volume. However, changes to the in-situ stress field caused by an earlier hydrofrac on subsequent hydraulic fractures are not accounted for in traditional hydrofrac design calculations. Presented here are the results from a set of transient, coupled hydro-mechanical simulations of a rock mass containing two wellbores using the discontinuum-based distinct-element method. The results demonstrate the influence of stress-shadows generated by a hydraulic fracture on the development of subsequent hydrofracs from an adjacent well. It is shown here that these interactions have the potential to change the size and effectiveness of the hydraulic fracture stimulation by changing the extent of the hydraulic fracture around the secondary well.

Jun 1, 2012

By Gerald Sanders

Presentation Topics ? We?re Going to the Moon Again? ? What is Lunar Mining ? In-Situ Resource Utilization? ? What Are The Challenges to Lunar Mining? ? What is NASA Currently Doing?

May 1, 2009

By F. Q. Barnes

"Uranium, thorium and yttrium have been recovered, since the 1950s, from pyritic quartz-pebble conglomerates occurring in the basal sediments of the Quirke syncline at Elliot Lake. Gold, an element of interest in similar type deposits occurring worldwide, is a very minor constituent of the Elliot Lake conglomerates because the provenance area of the sediments had few gold-bearing rocks.Uranium, thorium and rare elements are found in resistate and diagenetic minerals occurring in the matrix of the conglomerates. The valuable elements are recovered from the acid soluble minerals during the milling process.Large uranium reserves occur in mines found on both limbs of the Quirke syncline. Major reserves are being developed on the South Limb of the syncline, where the Stanleigh Mine, among four past-producers, has been reactivated.IntroductionUranium and thorium commonly occur in anomalous amounts in coarse basal sediments. Radioactivity in basal conglomeratic sediments is generally attributable to resistate minerals, that rarely occur in concentrations high enough to be of economic significance. One type of basal conglomerate found worldwide, in Precambrian cratonic basins, has uranium or uranium and gold concentrations large enough to be of economic interest. Principal among the occurrences are the pyritic quartz-pebble conglomerates of the Huronian in Canada, of the Witwatersrand in South Africa and at Jacobina in Brazil.The uranium and gold mineralization of these conglomerates was derived from provenance areas where both elements occurred and were later concentrated through source degradation and deposition in placers in a reducing environment. Only the Huronian conglomerates, generally much richer in uranium but with negligible gold, have been exploited solely for their uranium content.The uraniferous conglomerates of the Huronian at Elliot Lake, 500 km north of Toronto, continue to represent a major world source and supply of uranium concentrate."

Jan 1, 1986

By K. Sakaguchi, T. Yokoyama

"In-situ rock stress measurement was carried out in the Kamaishi mine of Iwate Prefecture to quantify the variation of the shallow crustal stress field associated with the 2011 Tohoku-oki earthquake. Stress measurement was conducted by the Compact Conical ended Borehole Overcoring (CCBO) technique, which is one of the stress relief method. The CCBO technique is the one of the suggested method of ISRM. Measurement period is from 1991 to 2014. Main results obtained in this study can be summarized as follows.The direction of the maximum principal stress did not change much before and after the earthquake. However, the directions of the intermediate principal stress and the minimum principal stress of one year after the earthquake changed from those of before earthquake. Namely, the direction of intermediate principal stress was East-West horizontally, and the direction of minimum principal stress was vertically. This state of stress is reverse fault type and was maintained for three years after the earthquake.The magnitudes of principal stresses and the vertical stress of one year after the earthquake became more than the double before the earthquake. However, the magnitudes of the maximum principal of two year after the earthquake became smaller comparing with those of one year after the earthquake. Furthermore, the magnitudes of the intermediate principal stress and the minimum principal stress of two year after the earthquake became almost same as those before earthquake, and the vertical stress of two year after the earthquake became almost equal with the overburden pressure. And the magnitudes of three principal stresses of three year after the earthquake became the same level before the earthquake."

Jan 1, 2015

By SangHyeok Han

Selecting the best possible cranes and identifying spatial conflict-free locations on sites can result in productivity and safety improvements for large-scale industrial construction projects. In the current practice, experienced lift engineers select cranes based on the heaviest lift and/or the largest lifting radius of the identified crane. This practice is relatively time-consuming, and optimization of the crane?s use and location is also difficult. There are many factors which need to be considered during the crane selection process, a reality which further complicates the process. This paper presents a framework which aims at developing a decision support system to enhance the crane selection process and collision-free path planning for large-scale construction projects. This paper utilizes an innovative crane selection matrix in order to establish a process for optimized crane selection for construction projects. The study considers more than 40 different factors in order to reduce time and improve safety for crane operations. Following finalization of crane type (mobile crane versus tower crane), a visualization model to simulate crane operation and identify collision-free crane operation paths is proposed. This process can assist project managers to plan the lifting process more effectively and efficiently. A case study-based approach was utilized to demonstrate the proposed methodology. The methodology was tested in the planning and construction process for boiler house structures in Mannheim, Germany. The project entailed numerous challenges: one of the major tasks was to lift a 102-ton load on the top of the boiler structure through crane collaboration; space limitations on site also presented several challenges related to crane selection, location, and operation processes. Based on the project constraints, the proposed crane selection framework, and the visualization models, two tower cranes were selected and successfully implemented in the case study.

Aug 1, 2013

By C J. Coveney

This paper, after a brief introduction to the mineralization and structure in the mine area, outlines the methods now being employed for grade control at Bethlehem Copper Corporation. Sampling, subgrade drilling, blasting and the actual outlining of the ore are among the topics covered. The paper concludes with a summary of the results obtained, showing a reduction in dilution and an improvement in the grade of the copper ore going to the mill. Introduction T HE Bethlehem property is located in southern British Columbia in the Highland Valley about 30 miles southeast of the town of Ashcroft. The property is located within the Guichon batholith. The rock comprising the batholith is a massive, coarse-textured diorite, which, at Bethlehem, has been intruded by a younger quartz diorite, porphyries and breccia, referred to as the "Younger Complex." Mineralization, consisting of chalcopyrite and bornite with minor pyrite and molybdenite, occurs as disseminations, fracture fillings and coarse blebs. The ore zone lies close to the Guichon -Younger Complex contact where, prior to the development of the breccia, the rocks were shattered and jointed. Subsequent mineral

Jan 1, 1965

By Baisheng Nie, Longlong Yang, Tao Yang, Wenjie Jia

"Gas adsorption in coal is an exothermic and physical process. Temperature might change during the dynamical process. In order to get the temperature variation of gas adsorption process, the experiment system which can test the temperature variation and analyze the thermal effect was established. Gas adsorption experiments under different conditions were done by using the test system. The results show that temperature increases during the adsorption process. It is an exothermic reaction process. Also, the temperature variation and the variation gradient increase with the increasing of equilibrium pressure. The temperature variation value is smaller if the experiment temperature is higher. The paper will provide basic experimental data for explaining gas adsorption mechanism better.INTRODUCTIONChina is the largest coal producer in the world while it also has the most serious coal mine disasters. According to the statistics, there are nearly a thousand coal mines in China including more than 110 the key state-owned mines risking to happen coal and gas outburst. Hundreds of coal and gas outburst occur each year which often causes serious casualties and economic losses (State Administration of Work Safety, 2007). With the continuing exploitation of the coal resources, the depth of the Chinese coal mines increases about 100 meters every year which causes the situation of gas accident becoming more and more serious (Xie et al., 2006).At present, the real mechanism of gas adsorption, desorption and the diffusion process in coal and the influence factor of it are not so clear. And because of the limit of prediction method and the technological level caused gas accident prevention theory and technology not so valid."

Jan 1, 2015

By J. Bardinas

"The use of autogenous mills has become widespread, owing to their capacity and favorable capital and operating costs. Optimal operation of these systems is critical, given their high energy consumption and effect on downstream processing. A considerable effort has been spent over the years in the development of advanced control systems to achieve a better performance in this regard. However, despite significant advances, the problem still remains challenging, owing to the nonlinear behaviour of the system with respect to the mill variables, and, the unmeasured ore variability come from the mine.The mill load, in particular, can be seen as a state variable of the mill, which could be important for; modelling and control, and, important insights into the mill behaviour. In this investigation, time series cluster analysis was performed using online mill load measurements in order to identify the different control states of the mill. More specifically, this time series was divided into short non-overlapping segments. A distance matrix was set up for each segment and the information was captured by means of textural features, similar to that used in multivariate image analysis. These wavelet and grey level cooccurrence matrix features could subsequently be used to rapidly identify the normal operating conditions from the feed disturbances in the mill.In principle, the methods and models presented here, once suitably validated and calibrated, could be used in online process monitoring of autogenous mills. They also could serve as a foundation for developing more advanced process control models."

Jan 1, 2016

By S. Z. R. Pinkney

Positron Emission Tomography (PET) is a medical technique that produces three dimensional images of the body, commonly to aid diagnosis and treatment of tumours. PET has been developed by the University of Birmingham in order to track particles in an opaque system which is known as Positron Emission Particle Tracking (PEPT). The object to be tracked is irradiated. As the radionuclide decays positrons are produced; when these collide with electrons a pair of concurrent parallel back-to-back gamma waves are emitted and detected, from which the position of the object can be calculated. Stirred media mills are used for particle size reduction. The mill is usually operated at high solids loading with grinding media and has a polyurethane or polyurethane-lined steel pot and is thus opaque. For this study grinding media has been directly irradiated and tracked using the PET camera during the grind. The stirred media mill can be divided into cells of equal volume known as voxels. The fraction of the total time the irradiated media spend in each voxel can be shown in an occupancy diagram. The mean velocity and kinetic energy of the media for each voxel are calculated and also plotted. In occupancy and kinetic energy plots colour indicates the value of the voxel, in dimensionless time and Joules respectively. The arrow in velocity plots shows direction and length of arrow indicates magnitude of the mean velocity for the voxel. From these diagrams and further data analysis a detailed understanding of the flow patterns, media behaviour and high energy areas of the mill can be developed. Variables considered were the tip speed of the impeller and density of the grinding media. It was found that the grinder has three distinct regions: above, at and below the impeller with each region having its own flow patterns and velocity and kinetic energy profiles. These are different for each variable and so are used to characterise the grind. Tip speed and density of the grinding media were shown to both affect the velocity of the media and the proportion of time spent in the each region of the grinder.

Aug 1, 2013

By Nathan Deisman

Coupled reservoir geomechanical simulations have become a key component of caprock integrity assessments for SAGD operations. This work demonstrates the differences of stress evolution when considering coupled versus uncoupled reservoir simulation. Coupled simulation involves the use of a reservoir and a geomechanical simulator with feedback to each simulator to update reservoir or geomechanical variable (permeability, porosity, relative permeability, pressure, temperature, saturations). Uncoupled simulation only passes the pressure and temperature to the geomechanical simulation with no reservoir simulator updating. Therefore, it is possible to complete uncoupled simulations exclusively with no knowledge of geomechanical flow property evolution. However, it is important to understand the differences between the stress evolution in each model for caprock integrity analysis. A single geological model was selected and parametric analysis was completed while varying the geomechanical the production injection pressures (1600 kPa, 1900 kPa, 2200 kPa) for a reservoir with an initial pressure at the injector of 1300 kPa. The results of the six uncoupled and coupled models are compared through the changes in mean stress, shear stress, and strength with focus on geomechanical assessment of caprock integrity.

Jun 1, 2012

By B. B. Adhikari, S. Alam, Ohto Kawakita, Abe Pangeni

Effective recovery of gold was investigated by using adsorption gels prepared from pure cellulose, cotton and paper by treating with concentrated sulfuric acid. Only gold was adsorbed with extraordinary high loading capacity from varying concentrations of hydrochloric acid separated from other precious metals and base metals. The formation of fine powders of metallic gold was visually observed, which is attributable to the selective reduction of gold (III) ion to metallic gold clue to its high oxidation-reduction potential. Recovery of gold from the leach liquor of hydrochloric acid of circuit boards from spent mobile phones was attempted using pure cellulose gel.

Jan 1, 2011

By J. F. Wright

Introduction Previous to 1924 the mining fields of Manitoba and adjoining territory had not been prospected in detail, and the reports of the exploration of the mineral discoveries to that date had been discouraging. As a result of the apparent failure of all the mining operations, some considered that geological conditions in the country westward from lake Superior extending across western Ontario, eastern and northern Manitoba, and northern Saskatchewan, were different from those in the northeastern part of Ontario, where large gold mines had been developed. Discoveries of importance thus were necessary to renew interest in the mining possibilities of this part of the Canadian Shield, and the successful operations at Flin Flon and Howey in large part were responsible for the beginning of the present activity in what may be described as the part of the pre-Cambrian Shield within central Canada. In Manitoba, the more important developments at present are in the Central Manitoba, Gods Lake, and Knee Lake fields. The large area from west of Flin Flon east to Herb Lake, also, is being explored carefully for gold deposits of merit. A number of properties in Red Lake, Woman Lake, and Pickle Crow areas are being drilled and explored underground. Many of the mines of the Lake of the Woods area, that were producing gold 30 years ago, are re-opened, and new prospects in this field and in the country to the east are being explored. The recent development of Little Long Lac mine in an area near the railway, and considered by some to have been thoroughly prospected years ago, has stimulated interest in the areas formerly prospected. In the autumn of 1934, the belts of greenstone and sediments in the country east of lake Nipigon were staked, and deposits in these fields will be explored in detail this year. This paper is presented to discuss the general features of the geology and gold deposits of the various prospecting fields in Manitoba and adjoining territory. Details of a number of the areas and mines will be presented at this meeting in papers by Barton on Little Long Lac, Tanton on Sturgeon River, Baker on Gods Lake, and Brownell and Kinkel on Flin Flon. Although mining was not active in most of this territory previous to 1930, geologists of the various government departments continued field studies and interesting reports were issued.

Jan 1, 1935

By S. A. Ghoreishi-Madiseh

Underground mines, with their relatively high ground temperature and their extensive backfilled stopes provide a great opportunity for producing geothermal heat. The novel idea of installing a network of heat exchange tubes into stopes prior to backfill placement converts each mine stope into a heat producing battery. In this system, backfill plays the role of the heat exchange medium conducting heat from the surrounding rockwalls to the heat exchange tubes. This geothermal heat can be used for heating: mine facilities and buildings, the intake air, a close-by mineral processing plant, or even nearby communities. This paper investigates the possibility of extracting renewable geothermal energy from backfilled mine stopes by means of closed-loop geothermal cycles. To simulate realistic operational conditions a heat transfer model is developed and solved numerically. To evaluate the numerical results, a small scale physical model is constructed and the experimental results are compared with the simulation results. The study estimates the sustainable rate at which heat can be extracted from a typical underground mine stope, the resulting outlet temperature and performance of the geothermal system. The results show that mine stopes are capable of sustainably producing geothermal heat not only when the mine is active, but also after the depletion of the ore body. Therefore, an underground mine will no longer be perceived as an enduring economic liability, but as a long-lasting source of clean, renewable, and inexpensive low-grade geothermal heat.

Aug 1, 2013

By M. Duncan

Lightweight, high-pressure cylinders for compressed hydrogen storage are essential components for fuel cell vehicles. Storage volume and mass are two key considerations. Current on-board hydrogen storage systems are based on a maximum pressure of 350 bar. While 350 bar systems are excellent solutions for many applications, some situations require higher storage densities due to space restrictions. As a result, significant research and development work has been expended by cylinder manufacturers, systems providers, testing agencies and automotive manufacturers to develop 700 bar systems with reduced storage volumes. Dynetek Industries Ltd. has proactively developed several 700 bar storage cylinders based on a seamless aluminum liner over wrapped with a carbon fiber composite. This paper presents the challenges and processes involved in the design, testing and certification for Dynetek Industries Ltd. 700 bar cylinders. This paper also provides reasoning for further volume and mass optimization of compressed hydrogen cylinders through the establishment of realistic cylinder usage parameters in standards. In particular, the overly conservative fill life requirement for cylinders is examined.

Jan 1, 2005

By H. Higuchi

The Sumitomo Metal Mining Company Ltd. (SMM) started to produce electrolytic nickel at the Niihama Nickel Refinery in 1939. In 1992, the conventional matte electrorefining process was converted to the matte chlorine leach electrowinning (MCLE) process, which is currently in practice. SMM has mainly used two kinds of nickel matte as the raw material for the MCLE process. Treatment of new raw materials, which have different impurity contents from the original nickel matte, has become mandatory because of changes in the market. Therefore, the MCLE process has been required to increase its flexibility to treat the different impurity contents in the new raw materials. An increase in the capacity for iron removal is included in such requirements. A new iron removal circuit in the MCLE process, based on a process development study, was recently installed. The iron removal circuit is in operation, and efforts are currently underway to optimize the performance of the circuit by changing the present operating parameters. In addition to the removal of the iron, the application is also expected to improve the nickel recovery. The outline of the new circuit and the current iron balance in the MCLE process are described in this paper, together with the effect of the circuit on iron treatment capacity.

Jan 1, 2006

By J. A. Finch, R. R. Cunningham

The amount of foam volume generated in relation to the gas flowrate has long been used to define the foaminess of a solution and to characterize surfactants. The vessel geometry and gas flowrate range can affect the foam volume results. A fixed area column was tested alongside a variable area conical vessel with two surfactants. It was found that the fixed area vessel will cause foam volume to expand or contract which masks the effect of the surfactant. The conical vessel showed two regimes of foam volume production dependant on gas flowrate. The low gas flowrate regime revealed the physiochemical nature of the surfactant while a high gas flowrate revealed kinematic properties. Foaming properties of a surfactant is best determined with a variable area vessel at low gas flowrate.

Jan 1, 2009

By Siavash Zamiran, Abdolreza Osouli

"One of the most concerns of room and pillar mining system is subsidence of the ground surface due to coal mining particularly in room and pillar mines. Subsidence of ground surface is a result of floor, pillar, or roof failure of the mine. At the same, due to many difficulties associated with surface disposal facilities of coal refuse, some mining companies are trying to use underground space as a disposal storage place. In this study, stability and subsidence analyses of an underground coal mine located in the Illinois Basin are conducted. This room and pillar mine was abandoned and later on was used as a storage place to accommodate the coal fine refuse with slurry backfilling method. The geological stratigrophy and geomechanical properties of the mine floor and roof were collected. Floor and pillar stability analyses were conducted for areas with various extraction ratios. The stability of the mine was evaluated both prior and after slurry backfilling. The floor and pillar stability analyses results of the mine due to moisture exposure after slurry backfilling are discussed. The subsidence potential due to mine failure is also evaluated.INTRODUCTIONA typical lithology of coal seams in the Illinois Basin consists of weak underclay stratum. The immediate weak underclay causes frequent floor instability problems in Illinois underground coal mines. There are two different stages in assessing floor stability of the mines where slurry backfilling is planned. The first stage is during the mining operation when weak underclay layer squeezes under pillar stress and results in punching or bearing capacity failure. The second stage is after slurry backfilling. During this stage, the slurry material soaks non-durable floor layers and causes strength reduction in floor material. Pillar stability conditions should also be taken into account during both the operational period and after the slurry backfilling."

Jan 1, 2015

By P. J. Finnis

This paper describes the use of wire rope on open-pit mining equipment, giving specifications and examples of the performance achieved. Installation methods are also discussed, making the paper of considerable practical use to mine operators.

Jan 1, 1973

By J. Someehneshin

Nowadays along with population growth, industry development, consumption of mineral resources and the fact that the reserves on hand are running out, the depth of surface and underground mines for further exploitation are increasing. During recent years, in underground mining, the block caving method for low-grade and large-scale deposits has shown a growing rate of application. This method is very cost effective and economically affordable. The dimensions of blocks are one of the most important parameters which should be taken into account since it has been proved to have a great deal of effect on technical issues such as commencement of caving and mine design. Proper calculation of the length and width for a block in this method leads to proper caving and discharging which are the most important stages. Therefore, in this method, the calculation of the optimized dimensions (length and width) of blocks is not only important but also directly helps the productivity of extraction. In this study, firstly for the purpose of facilitation, some assumptions were considered and having used these assumptions for estimation of optimized length and width of block, a relationship based on rock mechanics and physics was explored. Furthermore, some necessary details were added to the said relationship and finally, it was transformed into an inequality. Solving this inequality provides us with the optimized length and width of the block. The explored relationship was analyzed with MATLAB software and the graphs thereof were drawn. In these graphs, each time one of the input parameters has been drawn up in a logical range so that it could be compared with previous states.

Aug 1, 2013

By Jaeheon Lee

"Biooxidation of gold ores or concentrates could be a very attractive alternative to pressure oxidation (POX) or roasting to liberate the gold grains from various sulfides. Crushed heap bioleaching was successful in US and many operations using tank bioleaching of gold concentrate are currently running around the world. Many parameters need to be considered during the project of sulfidic refractory gold ore process. Capital and operation costs are among the most important ones. Run-of-mine heap biooxidation could be very inexpensive and the smaller the crush size (particle size), the more expensive the capital and operating costs for biooxidation application are expected. The capital cost of biooxidation could be a fraction of the cost for building POX plant or roaster and the operating cost could be 1/3 of POX or roasting depending on the method utilized. A new biooxidation process, Sand Farming, is introduced as an alternative to POX and tank biooxidation process. A relatively coarser particle size (P80 = 650 µm) of the process benefits the low cost of grinding against the conventional grinding size (P80 = 75 µm) for other options. The cost of Sand Farming is less than 40% of that of pressure oxidation with comparable gold recovery from the downstream process. This paper will review the laboratory scale testwork for various biooxidation process of sulfidic refractory gold ores and concentrates and provide the economic evaluation showing the biooxidation could be the most economic method without much sacrificing the overall gold recovery. INTRODUCTIONThe decreased availability and lower grade of raw materials has motivated industries to consider recovering values utilizing low cost process options. The process may treat high grade concentrates or submill grade ores that cannot be processed economically by conventional milling-flotation or leaching. Sulfidic refractory gold ores/concentrates have been economically processed by roasting, pressure oxidation, and biooxidation in stirred tank reactor. The process selection is based on a series of studies including multi-year long ore characterization and metallurgical investigations."

Jan 1, 2016