Search Documents

By J. H. Baek, D. W. Lee, B. K. Kim

Nanostructured Cu-Al203 composite powders were synthesized by thermochemical process for an electrode application. The synthesis procedures are 1) preparation of precursor powder by spray drying of solution made from copper and aluminum nitrates, 2) heat treatments to evaporate volatile components in the precursor powder and synthesis of nanostructured CuO+Al2O3, and 3) CuO reduction by hydrogen into Cu. The suggested procedures stimulated the formation of the gamma-Al2O3. The mean particle size of the final composite powders was 20nm, and the electrical conductivity and hardness in the hot-extruded bulk were competitive with Cu/Al2O3 composite by the conventional internal oxidation process.

Jan 1, 2004

By Lucas van Latum

A Model for Safety Swiss cheese metaphor of safety layers Image »Multiple layers with independent, often transient failure modes »For a loss to occur, all layers must fail independently and simultaneously ??Latent? failures are due to inherent system flaws ??Active? failures are due to unsafe acts

May 1, 2011

By Antonio Fontana

"Environmental problems encountered with the use of diesel equipment in underground mining operations are discussed. The concept and procedure o implementing the Health Effects Index equation as a means of quantitatively assessing an underground working environment is outlined and sample calculations are present ed. Advantages and disadvantages of utilizing this method are also discussed.IntroductionWith the introduction of diesel-powered mining equipment in the 1960s there arose several question s for the environmental engineer to consider. These included: 1. What are the constituents of diesel exhaust and how can they be detected and evaluated?2. What are the toxicities and long-term health effects of these constituents?3. What is the ventilating volume required to maintain the concentration of these constituents below toxic levels?Diesel engines are a class of reciprocating, internal combustion engines in which relatively high compression ratios are used to generate high air-charge temperatures, which cause ignition of fuel to occur spontaneously. Ideally, perfect combustion of the fuel would produce an exhaust consisting solely of nitrogen (N2), water (H2O), carbon dioxide (CO2) and oxygen (O2). However, because no combustion process is perfect, relatively small quantities of imperfect-combustion products, or pollutants, are also generated. These include hydrocarbons (HC), carbon monoxide (CO), nitric oxide (NO), nitrogen dioxide (NO2), carbon (C) or soot, and sulphur dioxide (SO2).Currently, the Regulations for Mines and Mining Plants, made under the Occupational Health and Safety Act (Section 176), stipulate that weekly tests shall be made to determine the carbon monoxide (CO) concentration in the undiluted exhaust and at the operator's position, and the nitrogent dioxide (NO2) concentration at the operator's position. Also, the aldehyde (as HCHO) concentration in the atmosphere, at the operator's position, is to be measured at least every three months. Threshold limit values (TLVs) have been established for each of the three combustion products, and each is regarded as a separate entity. Consequently, this does not allow for consideration of interactions and possible synergistic effects between the various exhaust components."

Jan 1, 1982

By D. Eriksen

Zero Emission Gas power, ZEG, is a novel concept where a high temperature solid oxide fuel cell (SOFC) is integrated with a reforming reactor producing hydrogen from natural gas through Sorption Enhanced Steam Methane Reforming (SESMR). The SOFC is used as a high temperature heat source for regeneration of the CO2-absorbent. Moreover, by using part of the produced hydrogen as fuel for the SOFC, the waste heat of the process is considerably reduced. Thus, the process has a very high thermal efficiency and produces both electricity and hydrogen from natural gas. In addition, a stream of pure CO2 is produced in the regeneration step and can be deposited or used commercially. Initial cost estimates indicate a cost of electricity and a cost of hydrogen well below today's prices. A small (1kWel + 1kW H2) demonstration set-up is under construction and experimental results and related research will be presented. This set-up comprises one 2.5kWth H2 SESMR-reactor (about 0.85 Nm3/h H2) operating batchwise with dolomite as the CO2-sorbent. The reactor developed is designed like a parallel plate heat exchanger where the mixture of sorbent and reforming catalyst is packed between the heat exchanging plates. The demonstration set-up includes a 1kW SOFC operating in a continuous mode. The set¬up will therefore demonstrate continuous simultaneous hydrogen- and electricity production, but cannot demonstrate simultanuous electricity- and CO2-production. The set?up is well equipped for on-line monitoring of gas composition, flows and temperatures. This important part of the demonstration set-up is developed and provided by Christian Michelsen Research (CMR). A minor part of the project is the development of a continuous circulating fluidized bed SESMR-reactor system and in another related project the focus is on the development of more suitable sorbents. In these two projects co-operation with University of British Columbia and Lousianna State University, respectively, is highly appreciated.

Jan 1, 2005

By John Hughes

1. De Beers, Diamonds and Canada 1.1. De Beers was founded long ago (1888, the same time that Canada became a country) in a rural mining village in South Africa. Today, we employ 22,000 people across 19 countries and have 14 mines including open pits, shafts, beach-sands and seabed. 1.2. Last year our sales were US$5.7 billion and our total production amounted to 47 million carats which means a 40% global market share. For the Kyoto buffs in the audience, the company consumes 66 million cubic metres of water per annum, 210 million litres of hydrocarbon fuel and 1,600 GWh of electricity. Stats are good, but aren?t as expressive as a movie. This one is 2 minutes long, which is quicker than I could elaborate. (Video 1 - 2 minutes) 2. De Beers in Botswana is the leading source of diamonds 2.1 Today Botswana is the Jewell in the Crown. There are three big open pits that enjoy economies of scale that make them the lowest cost producers. Last year 60 million tonnes of overburden and 30 million tonnes of ore were moved in Botswana alone. Botswana produced 31 million carats, compared to 14 million carats in South Africa and 2 million very high quality carats inn Namibia. 3. Diamond Mines provide feedstock? ?.to jewellery stores

Apr 1, 2005

By Zhibao Li, Lanmu Zeng

The behavior of dicalcium silicate in NaOH-NaAl(OH)4-Na2CO3 solution is of significance for controlling the silica level in the production of alumina via the sintering process. Dicalcium silicate samples were obtained through a twostep approach: coprecipitation of calcium and silicate from CaCl2-Na2SiO3-NaOH solutions; and calcination of the hydrated precursor at 1200°C for 4 hours. The optimization of the synthesis parameters including temperature, solution concentrations and aging time was also investigated. Xray diffraction (XRD) and chemical analysis show that the calcined solids include dicalcium silicate with trace amounts of wollastonite. The solubility of the synthesized dicalcium silicate in HCl, NaOH, mixed NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was determined. It was found that the solubility increases with increasing HCl and NaOH concentration. The effect of temperature on the solubility in HCl solutions is limited, but the solubility decreases with increasing temperature in NaOH solutions. The solubility of dicalcium silicate in NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was shown to increase with increased temperature, Al(OH)3 and Na2CO3 concentration. The BromleyZemaitis model for the aqueous electrolyte system was selected to predict the solubility of dicalcium silicate. The model’s predictions yielded certain success compared with experimental solubility data.

Jan 1, 2014

By Norm Clegg

The Plant Engineering and Maintenance Association of Canada PEMAC is a national, not-for-profit industry association for plant and facility maintenance, engineering and physical asset management in all industry sectors in Canada. Our mission is to provide professional development for our members and the profession in Canada

Feb 1, 2008

By L Mariani, G. Mendoza-Suarez

In this investigation, TiH2 powders were coated with copper and nickel by electroless plating to delay hydrogen evolution. Copper-coated samples were found to have a mixed acicular (2D growth) and cauliflower (3D growth) morphology whereas the nickel-coated samples had a cauliflower morphology. Examinations of the coated powder cross-sections revealed that the coating thickness ranges from 0.2 µm to 4 µm. Uncoated areas on the powder surface and coating flakes unattached to TiH2 particles suggest poor adhesion between the coating and the substrate. The phase transformation undergone by the TiH2 during dehydrogenation was studied in samples taken at intermediary points in the heating cycles and examined by XRD. The findings reveal that as the powder is heated from room temperature to 800°C, it changes from TiH1.971 to Tiu and to aTi. Differential Thermal Analysis (DTA) was performed to study the effects of the coatings on the temperature of hydrogen release. It was found that increasing the number of plating iterations, and therefore the thickness of the coating, creates a significant shift in the temperature of gas release.

Jan 1, 2006

By K. Feindel

The distribution of water in operating fuel cells must be carefully managed to optimize the performance, durability, and functionality of the system. For example, the ionic conductivity of polymer electrolyte membranes decreases as membrane hydration is reduced. Flooding at the cathode inhibits mass transport, and it can lead to failure of materials. Build up of liquid water in the gas flow channels of a fuel cell stack will create a non-uniform distribution of pressure drops across the individual cells. We will discuss the application of 1H NMR microscopy to investigate in situ the production and distribution of water throughout an operating H2/O2 polymer electrolyte membrane fuel cell. Polymer electrolyte direct methanol fuel cells posses high theoretical storage capacities as power systems for portable electronic devices. There are, however, two long-standing hurdles to development of practical methanol fuel cell systems. First, the electro oxidation of methanol at the anode of the fuel cell is poisoned by absorbed carbon monoxide, an intermediate in methanol electro oxidation. Second, methanol readily crosses over from the anode to the cathode of the fuel cell. This methanol crossover wastes fuel, and it poisons the electro reduction of oxygen at the cathode. We are investigating use of 2-propanol as an alternative to methanol as a fuel. 2-Propanol is less toxic than methanol, and it is less prone to crossover from the anode to the cathode. More significant, however, is that the electro oxidation of 2-propanol to acetone is faster than the electro oxidation of methanol because it avoids formation of adsorbed carbon monoxide. We will present active catalyst systems for the electro oxidation of 2¬propanol to acetone in fuel cells. We will also present methods to convert the resulting acetone back into 2-propanol, possibly leading towards rechargeable portable fuel cell systems.

Jan 1, 2005

An Attractive Investment ?Near term low cost and secure PGM producer ?restricted supply legislated demand ?strong pipeline of resource development ?Building Canada?s largest undeveloped PGM-Cu resource ?All work (resource, reserves, DFS, EA) is NI43-101 compliant ?Strong balance sheet: over $8 m in cash with no debt

May 1, 2010

By Bian Xue, Wu Wenyuan

High quality, mono-dispersed, hollow CeO2 microspheres with high surface area were produced by a spray pyrolysis method at 700oC. CeCl3 was used as the raw material of the process rather than Ce(NO3)3 because the latter is relatively difficult to obtain in industrial quantities. X-ray diffraction and electron microscopy results confirm the high quality synthesis of hollow CeO2 microspheres with narrow size distribution, good mono-disperse, and good reproducibility. The process of the formation of mono-dispersive CeO2 microspheres was investigated by chemical dynamics and a possible mechanism is proposed. This simple method for synthesis of CeO2 microspheres is easily scaled up to fabricate other metal oxide nanostructured materials at industrial scale.

Jan 1, 2014

By Chih-Huey Lin

The Au/?-Al2O3 catalyst prepared by AuCl3 impregnation is subjected to the influence of residual chlorine after an oven drying. A post-impregnation NH4OH treatment was able to eliminate chlorine, and to reduce the cluster size of Au moiety. However, the CO oxidation activity was not increased by this post-impregnation NH4OH treatment. This suggests that certain metal-support interaction (MSI) is the determining factor for the activity of Au catalysts. Thermal treatment under H2, O2 or He was attempted to increase MSI of the prepared catalyst with or without the post-impregnation NH4OH treatment. No significant activity enhancement was found but the TPD analysis suggests that a H2 treatment has a higher chance to induce MSI.

Oct 1, 2003

By S. Kodama, G. Sasaki, K. Matsugi, K. Sugio, Y. B. Choi

"Pure aluminum (Al) matrix composites with changing the volume fraction of TiB2 particle content from 10 to 30% was fabricated by spark plasma sintering (SPS) process. Then the microstructure, density, dispersibility and thermal conductivity of the composites was estimated. As increasing TiB2 content, the dispersibility of particles and the density of the composites degraded slightly. And, the effect of the dispersibility of TiB2 particles on the thermal conductivity was quite little. The thermal conductivity of the composites was less than the theoretical value calculated by Maxwell-Eucken equation considering the effect of the density. It is due the influence of the interface heat transfer rate, because these composites have many small sized particles and have high interface density.INTRODUCTION Recently, metal matrix composites (MMCs) have been used widely in electric / electronic components, architectural materials, transportation equipment, aerospace and a precision instruments, because it’s superior properties have been greatly watched. Demand of MMC for industrial use has been increasing gradually. Furthermore, multifunction properties are required for the composites strongly. By integrating the dissimilar materials, the composites have various properties that we cannot get from monolithic materials. On the other hand, the response to the thermal management is required for materials, recently, and the need for the structural material controlling the thermal conductivity has been increasing. Especially, superior thermal conductivity and good mechanical properties from room temperature to high temperature are required for heat sink and heat exchanger at the same time. In late years, a study on the composites combining carbon materials and aluminum and copper has been developing, and actually the composites with high thermal conductivity which is not provided in the conventional materials is developed. On the other hand, non-oxide ceramics particles such as SiC and AlN, TiB2 have good thermal conductivity. Particularly, as TiB2 has good electrical conductivity, TiB2 containing MMCs is expected as innovative materials used as electric/ electronic components. Furthermore, as TiB2 has low density, high melting point, low thermal expansion and good deformation resistance, the development of high performance composites with multi-functional properties is expected. As thermal conductivity of pure Al and TiB2 are 225 and 66.4 W/mK, respectively, it is expected that the degradation of thermal conductivity by adding dispersant in Al matrix is suppressed. The authors have carried out a thermal conductivity, electrical conductivity, mechanical properties of 20 vol.% TiB2 dispersed Al composites (Sugio, 2016, Sasaki, 2016). In this study, the influence of quantity of addition of TiB2 on microstructure, thermal conductivity was studied minutely."

Jan 1, 2018

By Chun-Sheng Liao, Chun-Hua Yan, Sheng Wu, Fu-Xiang Cheng

"INTRODUCTIONChina is providing more than 90% of the rare earth products consumed in the whole world. Acidic extractants are commonly used in the extraction separation of rare earths. Saponification of the acidic extractants by basic substances is usually necessary for the purpose of increasing and stabilizing their extraction capacity, and meanwhile inorganic acids are required for both scrubbing and stripping. Thus acids and bases are the main consumed chemicals, and the resulting salts are the main pollutants generated by rare earth separation processes. Currently, due to increasing environmental concerns in China, rare earth solvent extraction separation techniques are being developed to reduce both consumption and emission of chemicals, which is driving the developments on both theories and processes for solvent extraction separations.In the 1970s Prof. Xu et al. developed the Theory of Countercurrent Extraction (Xu, Li, & Yian, 1985). In recent years, the development of novel processes for rare earth separation has moved beyond the earlier theory. One rare earth separation process, the so-called hyperlink process, has been developed in the past decade and proven in industrial practice to dramatically reduce both the consumption and emission of chemicals during multi-component solvent extraction separations, and therefore is now widely used in the Chinese rare earth separation industry (Liao, Wu, Cheng, Wang, Liu, Zhang, & Yan, 2013). The present article will give a brief review of the development of the theory of the hyperlink processes, and the hyperlink separation flowsheets for typical rare earth mines in China designed using the theory.HYPERLINK PROCESSES (LIAO et al., 2013)A flowsheet of multiple-component separation consists of a couple of separation units. The units of a conventional flowsheet separately consume chemicals for saponification and scrubbing and discharge wastewater with resulting salts. In contrast, the separation units in a hyperlink process are hyperlinked and thereby the chemical demands of the whole flowsheet are decreased. For a feed containing t components of A1, A2, …, and At, it has been proved in theory that the separation mode of (AtAt-1…A2)/(At-1At-2…A1) is preferred in a single separation unit. The hyperlinking between separation units can have two forms. The link between two units locating at a same separation level, such as between (A4A3)/(A3A2) and (A3A2)/(A2A1), is known as horizontal hyperlinking. The link between two units located on different levels, such as between (A4A3A2)/(A3A2A1) and (A3A2)/(A2A1), is known as vertical hyperlinking. Both the hyperlinking forms have been proven to save chemical usage and consequently to lower the pollution emissions in industrial practices as well as in theory."

Jan 1, 2016

By W. L. Single

"LET ME FIRST OF ALL thank you for sending this invitation to me to participate in this Annual Meeting of The Mining Society of Nova Scotia. As an engineer, although I don't get an opportunity to practice very much engineering these days, I am, of course, always pleased to be able to meet with my fellow engineers to exchange views, but I must admit that today I feel a little bit out of place in the midst of all the experts that are here today. Let me make one thing clear - I'm a generalist! Your program states that I am to make a keynote address. I have always thought that a keynote speech is one that says something that has not been said before - announces some new program or policy, or says something startling. I am sure you will understand when I tell you that keynote addresses are made by politicians and that civil servants speaking publicly are usually expected to give an account of what is, or what is likely, to happen as a result of policies that have been announced in keynote speeches by politicians. I am reminded of a statement by a distinguished parliamentarian who said, ""However exalted a civil servant may be, he is not above the elected officials."" So today I will confine myself to giving you an overview with particular emphasis on the development side of oil and gas. The theme of ""Oil and Gas"" is a topical one these days. I suppose it's because of all the copy that is being generated by the media on the U.S. energy crisis, the Mid-East situation, the fact that most of the world's proven oil reserves are in Arab hands and, of course, the accelerated exploration activity that is taking place in the North Sea, in the Arctic, and off the coast of Newfoundland and Nova Scotia."

Jan 1, 1973

By K. Regl, J. Berneder

"AMAG investigated different aspects to improve the resistance against grain coarsening in aerospace alloys during recrystallization and was successful in finding several opportunities to minimize this effect. The studies show that one aspect to counteract grain coarsening is the chemical composition and subsequently all phases that are formed during homogenization. Starting with a fine grain (~ 50 µm) can lead to a final grain size of few mm. On the other hand with a coarse initial grain size (approximately 150 µm) and the right chemical composition the grain size can stay almost constant despite different deformation steps. Additional we investigated different sequences for the component production to eliminate the problem of grain coarsening as a coarse grain has a detrimental effect on product performance.INTRODUCTION In the aircraft industry, aluminium sheets are most commonly deformed in their soft state, followed by solution heat treatment and natural or artificial aging. If the preceding deformation is in a critical amount, during the recrystallization at solution heat treatment grain coarsening can occur. A subsequent deformation to this condition leads to an orange peel surface, which requires additional polishing. Next to this extra effort the coarse grain size produces a drop in the mechanical properties, often below specification limits. If there is no subsequent deformation, this effect is not visible and without destructive testing there is no possibility to detect the error. As mentioned before, this effect occurs during recrystallization, which is a process that is driven by the stored energy in the microstructure. The two most important aspects for an increase of the stored energy are the increase of the grain boundaries fraction (smaller grain size) and the increase of the dislocation density caused by deformation. The increase in dislocation density during the deformation arise from trapping of existing dislocations and from the generation of new dislocations. During recrystallization all grains are built completely new, so all dislocations are removed (Humphreys & Hatherly, 2004). There are three requirements for recrystallization:"

Jan 1, 2018

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-ehalcopyrite core interlayered pyrite-sphalerite-galena (pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyritequartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone I) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (II and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone I, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F, fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By A. Kobzhanov, S. Saparova, S. Brochot, D. A. Mango

KATCO (an ORANO Mining and Kazatomprom joint venture) is the largest in-situ leach uranium mining operation in the world, exploiting the Muyunkum and Tortkuduk uranium deposits in southern Kazakhstan. After extraction from the deposits, uranium is then transported via a hydraulic network to be purified in three processing plants located near these deposits. Within KATCO, with the support of ORANO Mining and CASPEO, in 2018 and 2019, a large project that had as its main objective to improve the uranium accounting system was implemented. The objective of this paper is to describe this project and all the changes that it entailed. At KATCO plants, a black-box approach was previously used for uranium accounting. However, it is recommended to use all the available measurements and to deploy a data reconciliation model (between well-fields and plant) as the reconciliation uncertainty is overall lower and it provides a more accurate uranium balance. During the deployment of this project, the rules and algorithms to generate the uranium accounting report, the associated flow diagrams (for uranium accounting), the streams, units of operation, stocks, reporting and Key Performance Indicators calculation rules were re-defined.

Jan 1, 2020

By J. A. Russell

"UNTIL the last few years, the collieries of the Dominion Coal Company, Limited, while highly mechanized as to the cutting and transportation of the coal, still relied on the hand-loading of coal from the seam onto face conveyors. In these circumstances it was possible to assure that no large proportion of extraneous materials would be loaded with the coal, and the product could be quite well cleaned for the market by screening and hand-picking.Within the past few years, however, the Company has introduced an intensive programme of mechanization which will result in the virtual elimination of hand-loading .of coal. It has been the experience of other producers that mechanical loading inevitably leads to a very large increase in the amount of impurities in the product. This is occasioned by the fact that, at least up to the present, all types of loading machines have relied on the coal being broken from the seam by under-cutting and shooting. In this operation, a certain amount of roof and pavement material inevitably becomes mixed with the coal and, since selective loading is impossible with a loading machine, all this foreign material is loaded out with the product."

Jan 1, 1952

By Robert B. Parsons

"In all likelihood, Canada's mining industry would be adversely affected by corporate tax reform proposals actively being considered by the Department of Finance in Ottawa. When the next set of proposals for lax reform is released later this year as promised by Finance, the mining industry had better be prepared 10 take a hard look.IntroductionTwo federal budgets ago, in May 1985, Finance Minister Wilson tabled budget papers that were more massive in terms of volume than most federal budgets. Buried in this mass of documentation is a discussion paper entitled ""The Corporate Income Tax System-A Direction For Change"". When the discussion paper was tabled over one year ago, reaction from the business sector was almost nonexistent. By and large, the paper was regarded as nothing more than one more federal publication of mild academic interest.But, recent events suggest that this discussion paper for corporate tax reform could be the cornerstone for a series of changes to the tax laws which would have more profound and widespread effects for all sectors of the economy than any reform since 1971 . No industry in Canada can afford to ignore the movement afoot in Ottawa for corporate tax reform."

Jan 1, 1986