Search Documents

By Katsutoshi Saibara

Network communication note is a cloud system for an earthwork project. It enables backhoe operators and dump truck drivers to monitor their own works in progress currently and performed up to the present, and to have opportunity to reflect on their own bearings in the earthwork operations, and then could increase their situational awareness to the actual work conditions. First, this paper presents problems and purpose. Secondly, the configuration of the network communication note is reported. Thirdly, examples of communications enhanced by the network communication note are shown. Finally, remarks are described.

Aug 1, 2013

By J. L. Gartshore

PRACTICALLY all of Quebec's chrysotile asbestos production derives from twelve mining and milling operations located in the "Eastern Townships" area of the province. The annual output of these twelve operations exceeds one million tons of chrysotile asbestos, valued at over one hundred million dollars, and is shipped to manufacturers spread over all six continental areas of the world. A total of approximately twenty million ton of asbestos ore yearly, or about seventy-five thousand tons a day, is mined. Individually, the operations vary in size from about two thousand tons to thirty thousand tons per day. Removal of waste rock and overburden to develop these ore tonnages varies greatly from one mine to another, but would probably average out at about a one to one ratio.

Jan 1, 1962

By P. G. Hallof

The exploration staff of Campbell-Chibougamau Mines Limited has used past experience to delineate several areas of geologic interest under Lake. Chibougamau. Du• ring the winter of 1964-65, a reconnaissance induced polarization survey was carried out on the lake. First, several lines were surveyed over the known mu1.erahza-tion at the Henderson mine; the grid was then extended into the areas of interest. Several anomalous zones were located and drilled; one, of these proved to be of economic interest.

Jan 1, 1967

By Y. Y. Yemelyanov, S. S. Gudkov, A. V. Boldyrev, A. V. Bogorodskiy, S. V. Balikov

"A series of tests to optimize pressure oxidation- carbon-in-leach process (POX-CIL) of goldbearing flotation concentrate with the addition of sodium chloride and activated carbon were carried out. Flotation concentrate which was generated during primary ores concentration from a large Russian deposit was used for these tests. The tests were performed with different concentrations of sodium chloride. It was found that the required sodium chloride concentration for gold leaching was 5 g/L. The tests performed with different additions of activated carbon showed that the amount of activated carbon should be at least 6% of the concentrate mass. The rate of sulfides oxidation was 67.7–99.8 %. The highest gold recovery was 98.6 %.INTRODUCTIONThe majority of gold-bearing ores are recommended to classify as amenable to cyanidation and refractory. Processes at elevated pressures and temperatures have become increasingly important in base metals hydrometallurgy (Lodeischikov, 1999, 2007; Naboichenko, Shneerson, Kalashnikova, & Chugaev, 2009; Thomas, 2005).Current pressure autoclaves – cyanidation flow sheets are capital intensive due to numerous circuits and the use of environmentally-unfriendly sodium cyanide. The use of halide-based lixiviants during pressure oxidation of precious metals can be a promising technique for refractory sulfide goldbearing mineral raw material hydrometallurgical processing (Fleming, 2002, 2007, Kotlyar, Meretukov, & Strizhko, 2005).In this paper, we presented the results of the research on finding the optimum process parameters of pressure oxidation using an adsorbent for a refractory gold-bearing concentrate. A proposed flow sheet involves (Bogorodsky, Yelelianov, & Balikov, 2012):1. Gold-bearing sulfides oxidation followed by precious metals dissolution and the formation of gold and silver chloride complex;2. Reaction of the precious metals chloride complex with a carbon-based adsorbent;3. Precipitation of precious metals onto the adsorbent by EW and smelting of cathode precipitates into Dore bullions.This process allows POX of gold-bearing sulfides, precious metals dissolution and their precipitation on the adsorbent to be executed in one single vessel. This study found that the most suitable lixiviant was sodium chloride. Fleming (2002) suggested that in the presence of a halide-based reagent (e.g. chlorine- ion reaction), the dissolution of gold during POX is achieved according to reaction 1:"

Jan 1, 2016

By K. Thuro, H. Käsling, F. Menschik

"With increasing data volume, due to enhancing requirements for ground investigation programs for large construction projects, the demand for more efficient filing systems is more and more growing. Depending on the project we also have to use flexible systems to cope with varying data out of different lab and field tests.The chair for Engineering Geology at TUM is developing a web-based database solution to handle all project relevant data in a more appropriate way. We aim to optimize our data management to achieve a fast and easy way of collecting, documenting and analyzing our gained data. The second objective is to provide an easy access to our data for project partners across broadly distributed locations.This Database system consists of a PHP web interface and a MySQL database core. The current setup allows an online access via Internet (www). We are able to grant and constrain access to all data or only arrays of data with our user management system to guarantee the safety of project data and respect all rights and proprietorship. The database system is of modular design and consists of the following three base modules: module of general project data, module of laboratory data and user management module. At the current stage we are able to save and work with all usually generated specific values from unconfined compressive strength tests, brazilian tensile strength tests, point load tests, CERCHAR and LCPC abrasivity tests and ultrasonic tests. The user is able to perform a simple statistical analysis within our database (e.g. average calculation of one sample) and export data as csv or xls files for further analysis.For specific questions within projects we are able to deploy and integrate further modules in our database system. At this moment, we are developing an add on to use this database for different drill test analyses. One of the tools correlates drilling performance and drill head wear measured in the field with rock mechanical properties, and extrapolates the data to estimate the performance and wear in new projects. Today we are managing 90 projects with 550 samples and almost 1350 lab tests with the base module.In our contribution we aim to demonstrate an efficient way of data structuring using a relational database for laboratory and field testing data."

Jan 1, 2015

By T. Grammatikopoulos, K. Gibbs, H. De Souza, C. Gunning

The mineralogy of any ore body is a key factor in defining ore zones and predicting minerals/metals behaviour during processing. The determination of forms of gold, defined as the different chemical states in which gold is encountered in ore deposits, is critical. The most commonly known form is that of gold minerals and alloys, while other forms of gold have been collectively described in the literature as submicroscopic gold (i.e., less than 1 µm in diameter). Gold mining operations generally deal with very low-grade ores, in the order of a few g/t, in which gold displays complex mineralogy. These difficulties complicate the mineralogical studies and pose challenges for processing and recovering the gold. A comprehensive understanding of the chemical forms of gold is necessary to define gold mineralization and optimize gold metallurgy. SGS Canada Inc. has been using QEMSCANTM and a Tescan automated SEM that are automated mineralogical techniques that provide vast amounts of data for microscopic Au. The data in conjunction with other physical and chemical methods provide a comprehensive delineation of the ore composition and behaviour.

Jan 1, 2011

By K. Buxmann

Climate change is a subject of growing concern. Based on the International Energy Agency, about 19% of man made greenhouse gas emissions globally are generated by the transport sector. This paper will focus on the environmental aspects of the light-weighting in transport and the resulting savings of fuel and electricity. Aluminium is an option for lightweight applications in transport, with very high benefits not only in the use stage, but also in the stage of vehicle recycling. Life cycle assessment is used to quantify the relative benefits of light-weighting specific components of cars, commercial road vehicles, buses, ships and trains. A vehicle consists of many components, which are produced by different processes and undergo different types of end-of-life operations. This document does not intend to compare a generic aluminium vehicle with a generic "heavy materials" vehicle. It rather tries to use a pragmatic approach based on specific examples of components where aluminium is used and can be used in the design of new vehicles, also taking into account future developments. The case studies in this paper are based on real cases where aluminium was used. For each component, sensitivity analyses are applied to see the impact of specific parameters such as the end-of-life recycling rate and the use stage driving distance. Significant greenhouse gas savings by the use of aluminium are demonstrated for cars and even higher ones for trucks, buses, trains and ships. In addition, the total potential benefits of light-weighting with aluminium are shown on the global level.

Jan 1, 2007

By C. Klinkenberg, G. Zhu, K. Hulka, S. V. Subramanian

A quantitative model based on strain accumulation in multi-pass rolling is developed to overcome a large critical strain for dynamic recrystallisation in a Nb microalloyed steel with high Mn content (HTP steel). The larger the critical strain for dynamic recrystallisation, the finer is the dynamically recrystallised grain size. The initial mill trial showed that it is feasible to achieve ultra-fine grain size by dynamic recrystallisation but the prevention of static recrystallisation in between passes is identified as an essential condition to suppress mixed grain size. The data-base on static softening kinetics at short interpass time was experimentally determined on WUMSI and incorporated in the model. The model is used to optimise the strip rolling schedule to prevent static recrystallisation in the interpass time. The rolling simulation of strip rolling schedule has validated the model prediction that it is possible to obtain a uniform ultra-fine ferrite grain size of about 1-2 micrometer diameter in final ferrite microstructure for industrial rolling parameters. A user friendly software package has been developed to apply the model for off-line control of mill processing parameters, i.e., time-temperature-deformation schedule of finish rolling in order to accumulate large strain to overcome a large critical strain for dynamic recrystallisation. The model is a powerful predictive tool for grain size control in multi-pass rolling.

Jan 1, 2004

By Bennett McLaughlin

AGNICO-EAGLE started sinking the Penna Shaft in 1995 with a hoisting plant capable of hoisting 1,800 tonnes per day from a 2,240 metre deep shaft. Exploration success lead to the installation of a hoisting plant capable of extracting 4,500 tonnes of ore and 1,800 tonnes of waste per day from a depth of 2,210 metres. The introduction of a new rope selection factor, permitting a safety factor of 4.0, represented the breakthrough required for a cost-effective project. This paper describes the process taken to introduce the new rope selection factor and its impact on the original plant.

May 1, 2001

By R. Harrisson, K. Esmaieli

Brunswick mine employs an ore and waste pass system for material transfer. This paper reviews the evolution and performance of ore pass systems at the mine. It presents the range of selected configurations, inclination, dimensions, etc. Select case studies are used to address the influence of structure, stress and materials handling on the longevity of the employed ore passes.

Jan 1, 2008

By S. K. Sharma, Sanket Bacchuwar, Prabal Kumar Agrwal, G. V. Rao

"Iron ore processing industries play a vital role in the Indian economy. At present Iron ore of around +64% Fe is used for production of Iron through blast furnace. To produce +64% Fe from low/medium grade ores, crushing & beneficiation is compulsory. But during these processes, large amount of slime is generated. It is estimated that 18% -25% of tailing is generated during the processing of iron ore. The iron ore slime is discarded because of its particle size and chemical composition not being suitable as feed to the blast furnace. Although the fines/slimes can be agglomerated to larger particle, the alumina to silica ratio which is normally more than one pose serious problem during sintering process and subsequent smelting in blast furnace. The alumina content in the slime needs to be reduced for it to be used as the feed for blast furnace. The sample assayed 61.40% Fe, 7.68% SiO2, and 1.52% Al2O3, LOI 2.63% and all other elements were found in critical limit. A series of 27 tests were conducted by using a spiral for optimisation of process parameters to produce a pellet grade concentrate from the stacked slimes obtained from Kirandul. This paper deals with the optimisation studies of various parameters of a spiral concentrator and helps to utilize the fines from tailing ponds.INTRODUCTIONReserves of high-grade iron ores are diminishing all over the world at an alarming rate. As a result, alternative ways of augmenting and conserving precious and non - renewable natural resources are being seriously considered. One such attractive option is the recovery of metal values from slimes / tailings. Iron ore tailings containing around 48 - 60% Fe are generated from the iron ore washing plants and are disposed into tailing ponds without any further utility. These tailings in the form of slimes are not suitable in iron and steel making due to the presence of higher amount of gangue constituents. Several beneficiation techniques have been tried from time to time to reduce the gangue so that the beneficiated products could be effectively used."

Jan 1, 2016

By R. H. Watson

A paper read by J. A. H. Church before the Northern Alberta Branch last February described a method of working thick inclined coal-seams from the dip upwards, with the view to preventing fire risk by using water for the stowage of waste workings, and extinguishing a conflagration should such break out, was favorably received; but there was some doubt as to the cost of such a method, as it involves a retreating system, which might prove too expensive for practical adoption. Let us consider a typical leasehold such as we are familiar with in the Rocky Mountains. The leasehold is crossed at one end by a mountain river, which is cut by the outcrop of a seam of coal, 30 feet in thickness, pitching as shown on the drawing herewith, which also shows the general line of the outcrop in elevation through the leasehold, which is two and a half miles long and contains 1,500 acres. The average lift is about 600 feet above river level and drilling has proved that the coalseam can be tapped at a depth of 1,500 feet, 2,000 feet down the pitch from the outcrop in the river, all as shown in the illustration, which is typical enough of our mountain conditions to serve the purposes of comparison of methods. We take up the leasehold and invest $30,000 to pay for drilling and prospecting; $30,000 more for the price of the lease to locator or holder, and say $100,000 to pay for a railway spur (it might cost twice this sum, but we are only comparing two methods in the same location) and "now we are ready to consider equipment and the cost of development.

Jan 1, 1924

By Ken Hester, Bruce Arthur

"Introduction""Pebble milling"" is a term used to describe secondary grinding done with rock pebbles rather than steel balls or other steel or metal shapes. This paper discusses pebble milling with particular attention being paid to uranium grinding circuits.Pebble milling is typically employed:a. where the cost of steel balls becomes exorbitant, as may be the case in an isolated area.b. where the extra steel added from steel ball consumption may be detrimental to further processing.c. where the over-all economics favour the use of pebbles rather than ball.Pebble milling differs from autogenous and semi-autogenous grinding in that a sized product has been removed from some part of the primary comminution circuit, and it is this sized product which is added as grinding media to the pebble milling stage. The pebbles do not necessarily have to be produced from the ore- ""foreign"" pebbles can be used. Also, pebble milling generally refers to grinding from a fine size, below about 6 mesh (3360 micron), with relatively small media, that is, secondary grinding. In South Africa, however, primary pebble mills are sometimes used to grind crusher house product, and thus function in place of rod mills. Pebbles for this service are large and heavy as they must weigh as much as balls used in similar service.The first large applications of pebble milling were in South Africa(n. ""Tube milling"" with pebbles started in 1904. The tube mill was simply a tumbling mill with a length to diameter ratio over two. A ""typical"" early tube mill was 5.5 ft. (1.7 m) in diameter and 16 ft. (4.9 m) in length. Diameters increased steadily. King(n mentions 8-ft. (2.4 m) units in his 1949 book. By 1961, the largest units discussed by Jackson('' were 12ft. (3. 7 m) in diameter."

Jan 1, 1989

By M. Abumiya, N. Onodera

Stabilization of arsenic via the precipitation of large-sized scorodite (FeAsO4·2H2O) particles usually involves the use of expensive autoclave systems operated under high temperature and pressure conditions. Alternatively, DOWA developed a novel scorodite synthesis process (DMSP®) wherein the Fe(II) ions in solution containing As(V) ions were oxidized by O2 gas under atmospheric pressure. In this process, crystalline scorodite particles were formed via the formation of a gel-like precursor containing Fe(II). Based on this concept, in this study, we have demonstrated the synthesis of scorodite particles by the addition of Fe(III)-containing solution to the experimental solution containing Fe(II) and As(V) ions, without the O2 gas oxidation process. Ferric sulfate (Fe2(SO4)3) was used as the source of Fe(III) ions. Results indicate the precipitation of scorodite particles, comparable to that of the O2 gas oxidation method.

Jan 1, 2014

By Arthur Notman

Since addressing the Institute a year ago on The Future of the Copper Industry (l), many things have happened, most of them bad. It has been a hard year for profits and prophets. It was, therefore, with consider-able perturbation that I accepted the gracious invitation of your Committee to reappear. On reviewing my remarks of a year ago, I. have wondered whether, under pressure of more important matters, the Committee had neglected to make a note of them, or whether they felt that further explanations from me were in order. In either event, I am glad that I am here and welcome the opportunity to make any contribution I can to a clearer understanding of the problems of copper to those concerned. The English-speaking nations own 80 per cent of the present world-production of the metal. Col. P. E. Barbour, Secretary of the Mining and Metallurgical Society of America, and I recently completed an estimate of the known world resources of copper. We placed the figure, in round numbers, at 100,000,000 tons of metal. Of this amount, about one-third lies in the United States, one-third in the British Empire, and one-third in South America; and all but 4 per cent of this is owned by British Empire and United States capital. Our figures do not include any estimates for Russia, Japan, or Europe, on which there are no available data. It is true, consequently, that the British Empire and the United States are the ones concerned. It seems to me to be a matter of great importance to the world at large, and of even greater importance to those nations themselves, that the known sources of supply of this metal, so essential both in peace and war, rest so strongly in their hands. I cannot believe that in the long run they will neglect their responsibilities in the wise administration of these resources.

Jan 1, 1932

By Zhen Lei

In Alberta, Canada, heavy industrial projects are constructed using a prefabrication approach: spools and pipes are produced in the factory, and are assembled into modules that are transported to the industrial plants for installation by mobile cranes. Planning the onsite mobile crane operations is critical to the project budget and schedule. However, due to the large magnitude of industrial projects, manual heavy lift planning is tedious, and the results are not particularly responsive to site changes. This paper introduces an integrated mobile crane management system developed by PCL Industrial Management Inc., in collaboration with the University of Alberta, which investigates crane location selection and path checking for field module assembly. The project information is stored in a database, and the proposed system retrieves data, performs the calculations, and records the results back to the database; the calculations involve automatically selecting locations for the mobile crane, considering the crane capacity, lifting range and utilization. Lift paths for modules are checked for feasibility based on selected locations, satisfying the site and crane configuration constraints, and crane walking paths are planned if needed. The designed system is tested in an industrial project to validate the effectiveness of the system.

Aug 1, 2013

By A. L. Mular

This paper provides a worthwhile contribution to the knowledge needed for calculating and using mathematical models of grinding circuits. The computer search algorithm proposed should remove much of the guesswork as well as reduce computer processing costs and improve the accuracy of estimated parameter values for grinding mill models.

Jan 1, 1970

By K. Hanumantha Rao, A. Javadi

Our recent studies revealed that the sulfide minerals in contact with water during grinding produced hydrogen peroxide (H2O2) where the amount of H2O2 production by the minerals found to be in the order of pyrite > chalcopyrite > sphalerite > galena. The H2O2 effect on the oxidation of pulp components and its influence on the concentrate grade and recovery in flotation have been studied and the results have been presented and discussed in this paper. Studies have also been carried out to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp and as well of controlling the formation of these species through known chemical means for depressing the generation of the oxidant. Flotation tests using a complex sulfide ore with the same reagent scheme that is being used at Boliden concentrator in Sweden but with the addition of i) collector and depressant, ii) Na2S reductant and iii) inorganic (EDTA) and organic (TETA) surface modifiers, during grinding stage have been performed to judge the beneficial or detrimental role of H2O2 on the selective flotation of sulfides. The results demonstrate that the selectivity of metal sulfides against pyrite increases with increasing generation of H2O2 in the pulp liquid. H2O2 is also found to be a better oxidant in chalcopyrite-galena flotation separation than the commonly used K2Cr2O7.

Jan 1, 2016

By C. Hu

A MOS capacitor hydrogen sensor array is reported for hydrogen gas distribution mapping. Si(100) was used as substrate for film deposition. After silicon oxide growing on the silicon surface with dry thermal oxidation, palladium film was sputtered on silicon oxide as hydrogen-sensitive gate material in MOS structure. The 3x3 sensor array was patterned on silicon substrate and packaged in one chip. Sensors' response was test with impedance analyzer. The sensors in array were calibrated in the hydrogen concentration range from 10ppm to 10000ppm. The 2D hydrogen concentration distribution was obtained with the calibrated sensor array.

Jan 1, 2005

By L. Veleva, Garcia. A., G. Perez

Aluminum is a metal used for the transmission of electricity of high voltage, in the construction industry and other areas. In atmospheric conditions aluminum forms an oxide layer (Alz03'H20) as a result of its corrosion, entering the passive state. The oxide layer can be destroyed by the presence of ions (Cr, SOx-n) developing localized (non uniform) corrosion attack by pitting, difficult for evaluation. The concepts of fractals and self-similarity were used in this study for the characterization of the development of localized corrosion. Images obtained with a scanning electron microscope (SEM) of samples of electrolytic aluminum wire that have been exposed during one year in ruralurban and marine-coastal environments of the humid tropical climate of Mexico, have been processed. The development of pitting has been studied as a function of time, making a statistics of the frequency of appearance of pits versus the area occupied by them. The data show that the distribution of the pits follows a power law. Therefore, the concept of self-similarity can be applied for the study of the phenomenon of localized corrosion, describing their development with time.

Jan 1, 2006