Search Documents

"A method is described for determining the viability of hard rock orebody extraction by block caving. Using a very limited amount of geotechnical data, the procedure enhances Laubscher’s empirical stability graph method by using the complex structural modelling system (ChaSM) to assess cavability and block cave tonnages.IntroductionIn considering the selection of suitable mining methods, block caving has gained popularity over other extraction systems in recent years (Butcher, 1999). This has been ascribed to the fact that block caving is the lowest cost per ton mining method, with orebodies that were in the past considered unsuitable for caving, now being successfully mined. However, even though all orebodies will cave, a problem exists in the evaluation of economic viability — it is necessary to be able to predict both when the orebody will cave and what will be the sizes of the initial ore fragments (and the associated tonnages) that report to the drawpoints. This problem is compounded by the fact that, during the scoping study phase of a project, only limited geotechnical data may exist on which to base an assessment of whether block caving is viable or not. Empirical and numerical methods of cavability assessment do not account for the full effects of geological discontinuity trace lengths, nor for the stress regime. Those require significant geotechnical data to be available. The result is that uncertainty may exist as to whether block caving is an economic option. This uncertainty is complicated by the fact that limited experience exists with the caving of more competent orebodies.This paper describes a method for assessing cavability, and for predicting the size of initial ore fragments and the tonnages reporting to block cave drawpoints, using only the level of data normally available during a scoping study. Fragment size and tonnages are assessed by identifying potentially unstable blocks and wedges in the undercut back using statistical joint data. The effects of lateral confining stresses are accounted for by comparing the in situ stress orientations with the joint orientations. To evaluate the accuracy of the method, a back analysis exercise was conducted to predict cavability and initial tonnage for a mine in which the actual behaviour is known. The method is then applied to cavability and tonnage predictions for a hard rock orebody."

Jan 1, 2002

By W. E. Oching, M. M. Ghomshei

"Collaboration among Ventilation Engineers, Mine Inspectors, worker representatives, health and safety officers and management is key to an effective operational mine ventilation management. Mine ventilation training, ventilation survey reports for mine stakeholders and interaction with mine frontline workers and management concerning safety, energy saving, assets management and maintenance are effective tools in implementing best industry practices and significant reduction of ventilation operating costs without compromising safety. These approaches may not be new to well established mining companies but the real dilemma is how to implement them effectively and this is what this paper will address.INTRODUCTIONManaging an effective mine ventilation system is becoming increasingly challenging, especially during tough economic times in the mining industry. Management strives for more production while frontline miners work hard to surpass the production targets, thus improving their incentives and above all aiming to enhance the prospects of their job security when the mining industry is facing challenging times. Taking shortcuts by not fully following the safety regulations or industry best practices are often notable, resulting in the rise of Workers Compensation Board claims and temporary shutdowns of active workings, compromising productivity and increasing the operating costs.In accordance with the Mines regulations in various jurisdictions in Canada and the US, it is evident that companies adhere to establishing basic ventilation management systems through the provision of the code of practice, procedures, work practices and standards/guidelines. This is aimed at ensuring the health and safety of underground workers (de Souza, 2017). However, the challenge to many operations is the improper implementation of the mine ventilation regulations including some managers showing reckless disregard for workers safety by focusing on production and not worrying to address ventilation problems (Steven & O'Keefe, 2010). Other challenges facing effective ventilation management include inadequate training of frontline workers on ventilation system and hazards associated with poor ventilation systems such as toxic gases, dust, heat, and underground explosions (Mufson et al., 2010; Suvar et al., 2017); friction between mine managers and the mine inspectors (Mufson et al., 2010), improper maintenance of ventilation system and inventory management, among others."

Jan 1, 2019

In most instances, the preferred mining methods in steeply dipping narrow vein deposits are selective methods such as cut and fill or shrinkage. The main advantage of these methods lies in the higher degree of control over dilution that can be achieved. However, where ore body geometry lends itself to it, high yield bulk methods can also be attractive. Higher productivity (and the associated lower costs) and lower worker exposure are some of the significant advantages that have made such methods so popular. The Lapa gold mine located in North-Western Quebec uses the long hole mining method (with cemented rock fill) very successfully despite challenging ground conditions. This paper focuses on the experience of the mine with regards to drilling and blasting practices. Firstly, the reasons that prompted the selection of this mining method at Lapa are examined. Secondly, the challenges that the difficult ground conditions found at Lapa pose to drilling and blasting are discussed. Finally, the results of trials of different drilling and blasting strategies that were performed at the mine are presented with particular emphasis on the lessons learned.

Aug 1, 2013

By Philip W. Johnson, Charles D. Haynes

"Abstract - The coalbed methane industry has become a prominent source of domestic natural gas, with its technology having evolved over the past 30 years. Whereas most coalbed methane wells are able to produce without major interruption over their economic lives, wells operating in an underground mining area are subject to being mined-through. If mine-through occurs, the productivity of the well is at least compromised, and may even be terminated. The economic consequences of mine-through may be relatively simple if mineral ownership and extraction rights are common for the coal and coalbed methane. However, if ownership is not common and a superior coalbed methane lease exists, the coalbed methane ownership must be compensated for lost production caused by mine-through. This paper presents a relatively straightforward method to calculate the value of the lost production caused by the mine-through. It uses technology from mining and petroleum engineering, as well as simple economics and financial management techniques.Sommaire - L’industrie de la production de méthane houiller est aujourd’hui une source importante de gaz naturel domestique dont la technologie a considérablement évolué au cours des trente dernières années. Bien que la plupart des puits de méthane houiller peuvent être mis en production durant l’entièreté de leur vie utile sans interruption majeure, les puits implantés en périphérie de mines souterraines sont sujets à être recoupés par ces dernières. Un tel recoupement peut compromettre, ou même mettre fin à la production d'un tel puits. Les conséquences économiques du recoupement par une mine souterraine peuvent être relativement simples quand les droits miniers et les droits d’extraction sont détenus en commun pour le charbon et le méthane houiller. Si toutefois ces droits ne sont pas détenus en commun et qu’il y a eu octroi d’une concession de méthane houiller de qualité supérieure, les détenteurs du méthane houiller doivent être compensés pour la perte de production résultant du recoupement par une mine souterraine. Cet article présente une méthode relativement simple pour calculer la valeur des pertes de production suite au recoupement par une mine souterraine. Cette méthode fait appel aux technologies de l’industrie minière et pétrolière ainsi qu’à des techniques simples d’économie et de gestion financière."

Jan 1, 2006

By W. M. G. Heeley

In the province of Alberta the coal measures dip at so many different angles, between the horizontal and the vertical, that many different systems of haulage are in use. I will, however, only touch briefly upon the general -systems in use, and devote the major portion of this paper to a discussion of endless-rope haulage and its adaptibility to various conditions in coal mines; dealing in particular with the endless-rope haulage that was installed at Brule during the month of August 1923. In coal seams that are approximately level, and newly opened, hand-putting or tramming from the face is the cheapest, but when the mine is further developed tramming is out of the question, and the use of ponies is the next consideration. The time arrives, however, when mining reaches a point where the economical haulage of coal by horses cannot be done profitably, and then some system of mechanical haulage must be installed. The installation of any system should be carefully considered before any particular type of haulage is adopted, because a great deal depends upon the grade or dip of the seam. Motor haulage is impossible to operate profitably on a grade of over 6 per cent and, while it is possible to use ponies, on short runs, up to 9 per cent, some other means of main and secondary haulage must be installed when a 9 per cent grade, is exceeded. I will, therefore, deal first with secondary haulage, because even though a main haulage is established, secondary haulage can be used to feed the main haulage.

Jan 1, 1925

By W. L. Murphy

The Star Lake property, located 115 km northeast of La Ronge, Saskatchewan is underlain by metamorphosed andesitic tuffs and flows which have been intruded by the dioritic to granitic Star Lake Pluton. Gold mineralization on the Star Lake property was first discovered at Ru h Lake by E. Beveridge in 1959 and by M. and E. Hird in 1961. In 1960 E. Partridge discovered Kahn 18 and Kahn 28. In 1982 the SMDC-Starrex joint venture completed geophysical and geochemical urveys including magnetics, VLF, IP/Resistivity, vegetation, bulk till and oil sampling, followed by drill testing of pecific targets. To date the most ignificant depo it is the 21 Zone which contain drill indicated reserves of 230,000 tons grading 0.5 oz/ton Au . The 21 Zone con ists of quartz with 5-10% (locally > 30%) drusy pyrite, minor chalcopyrite and trace amounts of scheelite, chalcocite and arsenopyrite. The 21 Zone is enclosed by a 25-50 m wide band of mylonitized monzonite. The mylonite occurs in the central portion of a 300 m wide northeasterly trending zone of brittle deformation .

Jan 1, 1986

By Olanrewaju A. Ojo, Xu Wang, Jian Xin Dong, Lina Zhang, Jerzy A. Szpunar

"The influence of crystallographic orientation on the pitting corrosion behavior of Ni-Fe-Cr alloy 028 was studied by a combination of X-ray diffraction (XRD), electron backscatter diffraction (EBSD), potentiodynamic polarization technique and atomic force microscopy (AFM). The results show that there is anisotropy of pitting corrosion that strongly depends on crystallographic orientation of surface planes. The distribution of pits frequency in standard stereographic triangle shows that the crystallographic planes close to {100} are more prone to pitting corrosion compared to planes of {110} and {111}. The calculation of surface energy (001) and (111) shows that the planes of high packing density of atoms have low surface energy with concomitant strong resistance to pitting corrosion. A correlation function between crystallographic orientation and pitting corrosion susceptibility suggests a method not only to predict the pitting resistance of a known textured materials, but also to improve corrosion resistance by controlling materials texture.INTRODUCTIONNickel-iron-chromium(Ni-Fe-Cr) alloys are widely used in various industries and engineering sectors due to their combination of good mechanical properties and high corrosion resistance(Hibner, 2001; Thomas, 2006; Ghosh, 2005).Ni-Fe-Cr alloy 028 (alloy 028)has such important characteristics worth mentioning. Alloy 028 contains high amounts of nickel, copper and molybdenum which improve its resistant to corrosion attack in reducing medium, and presence of high level of chromium makes it more resistant to oxidizing species. Moreover, alloy 028 is less expensive because of higher amount of iron compared to other similar alloys. Currently, alloy 028 is manufactured as evaporator tubes applied in the phosphoric acid production; production tubing and casing used in deep and sour gas wells; heat exchangers employed in nuclear power plants, and seawater-carrying piping and seawater-cooled heat exchangers (Bankiewicz, 2012; Kivisäkk, 2003; Gómez, 2003; Xian, 2012; Bellezze, 2004)"

Jan 1, 2017

By Sunil S. Gandhi

"Uranium occurrences are widely distributed in tuffaceous-argillaceous beds and abundant rhyolitic volcanic rocks of the upper Aillik group, which is more than 3 km thick and over 125 km by 40 km in areal extent. They include partially developed Kitts and Michelin deposits, containing 1560 and 7366 t U respectively.Uranium occurs mainly as disseminated fine pitchblende grains in beds and lenticular stratabound zones, and rarely as coarse pitchblende aggregates and thin veinlets. The Kitts deposit and ten other occurrences are in the argillaceous-tuffaceous beds within a steeply dipping stratigraphic zone, less than 50 m thick and over 20 km long, at the base of the upper Aillik group. The occurrences hosted by the rhyolitic rocks, numbering over fifty and including the Michelin deposit, are in elongate structural-stratigraphic belts or zones, and are characterized by a pronounced enrichment of soda and depletion of potash associated with mineralization. The mineralized zones are affected to a varying degree by Hudsonian deformation, metamorphism and granitic intrusions.The uranium mineralization is interpreted as genetically related to the felsic volcanism, involving syngenetic deposition in argillaceous-tuffaceous beds and epigenetic emplacement in rhyolites. The volcanic activity occurred 1855 ± 5 Ma ago according to a preliminary U-Pb zircon date on porphyritic rhyolite. Pitchblendesfrom the Kitts and Michelin deposits and a few other occurrences in rhyolites have yielded nearly concordant dates in 1810 to 1730 Ma range. They reflect resetting of isotopic equilibrium at the time of Hudsonian deformation. Other isotopic data on pitchblendes and galena from veins and aggregates .in the south near the 'Grenville Front' indicate local redistribution of uranium and radiogenic lead at the time of Grenville Orogeny approximately 1100 Ma ago."

Jan 1, 1986

By R. A. Wyman

A comparison of the amount of minus-28-mesh product produced by a standard grinding test procedure is provided for 45 non-metallic materials. The percentage of product, the weight of product per unit of energy used and the weight of product per mill revolution are shown. The results exhibited excellent reproducibility and demonstrated an accurate comparison of grindability for non-metallic materials.

Jan 1, 1977

By N. Novikov, M. Jastrzebski, N. Kryzhanovskaya, D. Shevchenko, I. Kapran, N. V. Novikov, T. Koehler, B. Zaporozhets

"The PFK FeNi Smelter was re-commissioned by Solway Resources in 2002, ending a long period of economic decline in the adjacent town. In 2009 Hatch was retained to design, supply and install a custom furnace crucible that would accommodate a capacity increase from 34 MW to 40 MW and increase campaign life through binding and cooling technologies, as part of ongoing improvement efforts. The involvement of PFK personnel was critical to the successful integration of the new furnace technology with the existing process and operational practice. The furnace upgrade project was completed in 18 months during 2010 – 2011. Since start-up, the furnace has exceeded production expectations, operating successfully at 42 MW.INTRODUCTIONAfter ceasing operations in the 1990’s, the Pobuzhsky Ferronickel Combine (PFK), located in central Ukraine, was stripped of useful equipment and deteriorated while dormant. The surrounding town experienced a period of economic decline throughout the 1990’s. Solway Industries purchased the complex in 2002 and began a systematic incremental program to re-commission the smelter using both local expertise and specialists from other parts of the former Soviet Union. This led to the re-birth of PFK as a successful toll-smelting complex, and a renaissance for the surrounding economy.As part of the continuing improvement program, PFK approached Hatch in 2009 to study the possibility of a capacity expansion from 34 MW to 40 MW. It was decided, based on the results of the study, to design and install a custom furnace crucible integrating the unique PFK FeNi process with modern Hatch furnace technology. This novel approach had many benefits, including: maximum re-use of existing furnace components (off-gas, feed equipment and transformers), minimal impact on upstream and downstream equipment and building structure, and the retention of a familiar operating regime. The latter was a key factor in the success of the project, as it allowed the extensive operating expertise of the PFK staff to remain highly relevant to the upgraded furnace. This led to minimized capital investment, a rapid start-up and no significant operational challenges switching over to the new equipment incorporating Hatch furnace technology."

Jan 1, 2012

By F. F. Roberto, E. Kirby, A. R. Marchbank

The application of biologically assisted methods for metal extraction in the mining industry has a long history, but development of modern techniques has been relatively slow. There is, however, a resurgence of interest in the industry with the recent development of methods to successfully treat base metals concentrates. Two major pilot plant programs for treatment of chalcopyrite concentrates have been initiated in the past year and results from one are beginning to be released. This paper provides an overview of methods that have been applied in the past, from the earliest deliberate applications of the technology, through the copper and uranium heap and dump leach applications, the more highly engineered agitated tank leach gold applications and the developments currently taking place in the industry.

Jan 1, 2003

By J. van Huyssteen, M. Cantor

Newmont Ghana Gold Limited's Ahafo Operation has matured from its project ramp up stage into steady state operations after three years of operation. Management focus has shifted from addressing construction and commissioning problems to optimization and improvement. This focus change has coincided with the introduction by Newmont of a Continuous Improvement (CI) program across the company which provided a project management methodology that can be used in the execution of smaller scale projects. This paper focuses on the application of CI principles at the Ahafo Plant through the discussion of several case studies that demonstrate how these principles are applied.

Jan 1, 2011

By Tyler J. Irving

"In June, 2018 Lalor Mine experienced a catastrophic blade failure of its No. 2 main exhaust fan. Over the following weeks several key changes were made to the auxiliary ventilation system to allow for continued production while the exhaust fans were repaired. Issues encountered during the period of reduced ventilation, and how they were addressed, are analyzed. The suspected causes of the exhaust fan blade failure and how risk was mitigated during the reconstruction are discussed. Key findings and lessons learned are summarized.INTRODUCTIONLalor Mine, owned and operated by Hudbay is an underground zinc, gold, and copper mine located in northern Manitoba. The mine workings extend to a depth of 1090 metres below surface and is ventilated using a push-pull system. The mine exhausts through the main exhaust raise; equipped with two, 2,500 HP fans and upcasts through a portal located at the neighboring mine, Chisel North. Air is supplied to Lalor Mine through four intake fans: The Production Shaft Downcast (two, 250 HP), Lalor Downcast (one, 400 HP), and Chisel Downcast (one, 600 HP) fans (Figure 1). In June 2018, Lalor was scheduled to produce approximately 4,000 tpd.On June 20, 2018 at 2:52 pm Lalor Mine experienced a fault on the Variable Frequency Drive (VFD) for Exhaust Fan No. 1. Time would be needed to complete the necessary repairs. The No. 2 exhaust fan was ramped up from 525 rpm to 800 rpm, 90% of its capacity, in order to maintain underground ventilation. At 4:46 pm, approximately two hours after the rpm was increased, exhaust fan No. 2 experienced a catastrophic blade failure. The forces from the blade failure resulted in the top half of the fan housing being thrown 50 metres from where it was installed; with several large sections of fan blade being thrown further (Figure 2)."

Jan 1, 2019

By Boyd Davis, Brook Zaback

"Among the first published papers from Prof. Torstein Utigard was work on imaging the aluminum electrolysis process and in-situ measurements of aluminum in cryolite melts. He and Prof. Jim Toguri used an x-ray radiographic technique to measure interfacial tension of aluminum drops. Publications using this equipment for aluminum electrolysis spanned from 1985 to 2006. As well, other methods were used to better understand electrolysis in molten salts, including hot-stage microscopy, direct observations from above the bath and water modeling techniques. For chloride systems (for magnesium and lithium), it is possible to see side-on the electrolysis using a quartz cell. In honour of Prof. Utigard’s contribution to this field, this paper presents a summary of work on visualization of molten salt electrolysis, including work done at the authors’ labs and others around the world. The paper will summarize key findings and their possible impact on molten salt electrolysis."

Jan 1, 2015

By H. L. Martin

A joint federal-provincial approach in gathering basic information from industry on mine production, concentrator operations and ore reserves, initiated during 1978, is a major step toward the goal of achieving better government-industry communication through a common data base. Information from questionnaires sent out by provincial governments is shared with the federal government; correct interpretation is ensured by mine visits conducted jointly by provincial and federal representatives. Initial focus is on nonferrous metal mines. The federal Department of Energy, Mines and Resources (EMR) is responsible for a national analysis that is aimed at the early detection of worrisome developments-and their reasons-in the flow from resources to reserves and from reserves to supply of these metals. The heart of the national analysis is the annual construction of a "monitoring curve", showing each metal's aggregated mine production as it would decrease over time if no new reserves and production capacity were to be added from the year of analysis. For a given metal, a comparison of monitoring curves from year to year can reveal early signs of supply stagnation. In anyone year, a monitoring curve in conjunction with foreseen needs for Canadian mine output will show the production gap that would have to be filled from reserves and production capacity yet to be developed. The production gaps for copper, nickel, zinc and lead, the four leading base metals mined in Canada, are shown for the 20-year period ahead, in the context of production achieved during the past 20 years. It is shown that reserve levels commensurate with likely future production levels would require that average annual reserve additions during 1978-98 exceed the average annual additions during the preceding 20 years. Reserve levels of all four metals have declined in recent years. A review of significant discoveries in the last five years suggests that this fall in reserves is not the result of a lack of exploration successes, but of stagnation in development for various economic reasons.

Jan 1, 1979

By F. T. Mooney

Introduction The Flin Flon mine of the Hudson Bay Mining and Smelting Company, Limited, is on the interprovincial boundary between Manitoba and Saskatchewan, about four hundred miles north of the Canada-United States boundary. The orebodies are gold, silver, zinc, and copper replacement deposits occurring as irregular lenses of massive sulphides, arranged en echelon, and irregular masses of disseminated copper sulphides in chlorite. The country rocks are of Precambrian age, dominantly lava flows. Development of the Mine The mine is opened by two vertical main shafts- the North Main and South Main shafts- 3,800 feet apart. The North Main shaft has a depth of 2,210 feet and the South Main shaft is completed for stoping operations to the 3,250-foot level (see Figure 1). These shafts are connected by main haulages driven, on the footwall side of the orebodies, at 520-foot intervals down to the 2,210-foot level. No. 3 (subsidiary) shaft is on the footwall side of the orebodies at a point between the North Main and South Main shafts, 2,400 feet south of the former. It has a depth of 3,250 feet and connects with all main haulage levels- with both Main shafts down to the 2,210-foot level and with the South Main shaft on the 2,750-, 3,000-, and 3,250-foot levels. Other openings tO the mine include B North fan raise, the opening due to the recovery of the open pit sill pillar, and several back-fill raises.

Jan 1, 1949

By Peter A. Bevan

"In massive and semi-massive deposits, it is essential to take samples continuously for specific gravity determination as well as for assays of the various metals of interest. Failure to use specific gravity in mixed deposits of high density contrast will result in incorrect determinations of the average grade.Graphs and linear equations of specific gravity against the grade of one metal are not considered accurate enough in a multi-mineral deposit, but appear to be very satisfactory in a theoretical one-sulphide/gangue mix. Specific gravities based on base-metal values only in massive sulphide deposits will result in underestimating the effect of low grade areas on the average grade and also cause a reduction in the calculated tonnage.IntroductionBy definition, a base-metal assay is the percentage of metal by weight contained in a sample, whether it be a soil or silt sample, a grab, chip or channel sample, or a section of diamond drill core.In those cases where there is a series of contiguous samples, say in diamond-drill core, the average grade may be required of the various assays that are above a desired or required cutoff grade.Internal low grade or waste can be included if the assays one side or the other are used to ""carry"" the lower grade material and the resulting average grade is above the cut-off grade. To determine the average grade, the individual assays are ""weighted"" by multiplying these values by their respective lengths, adding up the cumulative assay times length and dividing by the total length. This method is essentially a weighting by volume, because the core diameter is constant and is common to all the samples being considered for estimating the average grade . If some of the core samples have much higher specific gravities than others, and the specific gravities are not used in the weighting process, the resultant average grade will be over-estimated or underestimated, depending on the grade of the heavier sections. When core assays of approximately the same specific gravity or weight are averaged by length, the error in the weighted estimation of the average grade is negligible."

Jan 1, 1993

By M. Zavvari

Flotation, as with most engineering disciplines, involves testwork. Commonly this means going from lab scale to pilot scale to industrial scale. It is important to conduct tests to identify key parameters and to optimize even at the lab scale. To reduce the number of tests while maximizing the information, it is necessary to use Design of Experiment and Statistical Analysis. In this communication Fractional Factorial Design was used to identify the effect of 7 main factors on barite flotation recovery from jig gravity tailings at the Dorrin Kashan operation. The factors include: pH, collector and depressant dosage, impeller speed (RPM), pulp dilution, particle size and flotation time. By analysis of the output with Minitab software all factors were shown to have an effect. Among the factors, pH and flotation time have an interaction effect but the others have wise effect as an interaction effect and main effect. Finally, reliability tests at pH= 9, RPM= 1000, collector 1 000g/ton, depressant l 750g/ton, particle size 90 µm, flotation time 90 s, pulp dilution 23 % solids, the optimum level of each factor, were done. At the optimum level a barite concentrate with average specific gravity 4.308 g/cm3, average grade 93.72% and average recovery 90.04% was produced from the jig tail.

Jan 1, 2009

Arsenic bearing minerals such as enargite (Cu3AsS4) and tennantite (Cu12As4S13), which may associate with major copper minerals such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and bomite (Cu2FeS4), usually report to the copper concentrate in conventional flotation due to their similar flotation properties. Arsenic in a copper concentrate causes environmental problems and also problems in the subsequent pyrometallurgical process. Voltammetric studies were carried out to investigate the oxidation characteristics of enargite, tennantite, chalcopyrite, chalcocite and bomite. Contact angle measurements and micro-flotation tests were conducted to examine the flotation characteristics of enargite and chalcopyrite under controlled pulp potentials. Selective flotation of enargite from chalcopyrite under varied pulp potentials was conducted to investigate the feasibility of arsenic removal from a copper concentrate. The test results indicate that the non-arsenic bearing copper minerals ( chalcopyrite, chalcocite and bornite) were easier to oxidise than arsenic bearing minerals ( enargite and tennantite) in an alkaline solution. Enargite floated well at a potential as high as +0.45 V vs. SCE while chalcopyrite was completely depressed at a potential higher than +0.43 V vs. SCE. Selective flotation revealed that enargite can be successfully removed from chalcopyrite through controlling the pulp potential at +0.30 ~ +0.50 V vs. SCE.

Jan 1, 2007

By S. Gaulocher

Gearless mill drives (GMDs) are the workhorse in the mineral processing industries, more specifically when it comes to grinding crushed ore and cement (in various production stages) in semiautogenous (SAG) mills and large ball mills. They are renowned for their excellent reliability and robustness, long lifespan, and little need for maintenance, and thus yield a low total cost of ownership (TCO). A GMD represents a major investment for a mineral processing plant, and its availability is pivotal for the grinding process. As a basic rule, shut-down periods are to be minimized, but even much more important is that unscheduled shut-downs be avoided. In this contribution, we will present a portfolio of innovative remote diagnostic that consist of the following three key components: 1. Trouble shooting is a form of corrective maintenance and is based on state-of-the art remote access technology, thus enabling highly skilled engineers to access the current sensor readings anytime and from anywhere in order to resolve urgent problems together with the GMD user. 2. Periodic maintenance reports are a form of preventive and predictive maintenance and aim at continuous improvement based on long-term historical records and analyses of multiple measured signals. These detailed reports highlight the health and operational status of the GMD and are periodically (e.g. 3 months) submitted to the customer. 3. Remote condition monitoring spans across preventive and predictive maintenance and is based on continuous recording and automatic analyses of relevant signals using advanced algorithms. The main issue is how to handle the enormous flood of data in an intelligent manner. The results of these analyses are made available to both the GMD user and supplier in real time in order to increase the availability and reliability of the GMD. In this paper, we consider various parts of the GMD, e.g. the cycloconverter, the ring motor, the auxiliary devices (e.g. cooling and lubrication systems), and also phenomena related to the mill itself (e.g. state and quantity of charge). The signal analysis techniques range from simple threshold-based analyses to complex time and frequency domain analyses. We will illustrate the benefits of the proposed approaches with some selected examples.

Jan 1, 2012