Search Documents

Data collected from payload management systems at a number of surface mining operations show significant variance. Heavily loaded trucks travel slower up ramps than lightly loaded trucks. Faster trucks are slowed by the presence of slower trucks, resulting in 'bunching' and production losses. A stochastic model was constructed to simulate a truck haulage return cycle of 12.5 km at a large open pit gold mine in the USA. For a fleet of 35 trucks, the best estimate of the benefit achieved by a sustained reduction in payload variance of 25 per cent is a throughput increase of 1.6 per cent, within a possible error range of 0.6 to 3.2 per cent. This potential benefit is worthy of further investigation by Continuous Improvement teams at large open pit mines. The model also indicates that, under the right circumstances, provision of an overtaking lane can provide throughput benefits of up to ten per cent, The feasibility of providing unidirectional haulage circuits within large open pit mines should be examined.

May 1, 2010

By McQuade C. V

Mining is an activity which has, in the past, been regarded as often leaving land in a condition unfit for further use. As the need for development that is both economic and ecologically sustainable has grown, so the issue of re-use of land after mining has become significant. During operation it is usual that mine environmental conditions which minimise unnecessary or avoidable environmental impact are agreed with the regulatory authorities . These conditions are usually set down in such a way that they can be interpreted reasonably well by both miners and regulators. However, the conditions to be met by a mining company before it can be absolved of responsibility of a site are often less clear. The close-out criteria by which the success of rehabilitation programs will be judged have received little attention in the past. These conditions are now growing in importance as the costs of rehabilitation of a mine site to an agreed post-mining land use assume greater significance in the economics of mining. This paper briefly describes the status of close-out criteria presently being applied across Australia. A comparison is made with similar guidelines from other countries.

Jan 1, 1994

Hydraulic backfill is generally retained in stopes using permeable barricades. Mitchell et al (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et al (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading conditions. This paper discusses the circumstances that led to these incidents and analyses the modes of failure. The standards for the safe operating of hydraulic backfill systems are reviewed along with requirements for ongoing management and control. The design requirements of barricade construction are analysed and some appropriate guidelines introduced.

Jan 1, 1998

By T Baumgartl, T Huynh, K Tungpalan, E Wightman, M Edraki, M Tayebi-Khorami, L Huang, S Palaniandy, E Manlapig

With the increasing rate of tailing production worldwide there is a growing concern about the hazards of tailings storage facilities (TSF). Past and current mining, processing and waste disposal strategies that focus on the extraction of the valuable minerals, and an economic assessment only, are no longer suitable. Social implications and environmental legacies must be included for effective evaluation. This is possible by using an integrated assessment framework to evaluate more alternatives, including the production of additional saleable and benign streams, alternative tailings treatment and disposal as well as options for reuse, recycling and preprocessing of existing tailings. Tailings are not viewed as a final waste product but as part of the resource. From the sustainability perspective the models developed in integrated research programs will contribute to more effective methods for assessing different scenarios and potential processes and lead to better environmental management, increased production of benign tailings and improved efficiency of water and energy use and thus more responsible resource stewardship of the ore resource.This paper presents preliminary results from a multiyear research program on integrated tailings management at the Sustainable Minerals Institute (SMI), The University of Queensland, called ‘Designer Tailings’. The project involves the gathering of experimental and observational information on tailings biogeochemical processes to design and modify the range of activities within mineral processing plants, upstream characterisation ore and gangue, and downstream tailings management for desired tailings properties and outcomes. This information will assist the development of new total integrated value chain CITATION:Edraki, M, Huynh, T, Baumgartl, T, Huang, L, Andrusiewicz, M, Tungpalan, K, Tayebi-Khorami, M, Wightman, E, Palaniandy, S, Manlapig, E, Evans, C, Farrokhpay, S, Bradshaw, D and Vink, S, 2014. Designer tailings – an integrated model for tailings management, in Proceedings Life-of-Mine 2014 , pp 599–608 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By R Valenta, J Owen, D Kemp, E Lebre, G Corder

Copper plays an essential role in our society. It is one of the key materials supporting economic growth and human development in emerging economies, for its common use in construction, power generation and transmission. It is also a critical metal for the transition to a low carbon future, particularly for its uses in renewable energy and electric vehicles. As a result, global demand for copper has been increasing steadily and is predicted to continue in the future. The demand-supply gap is currently growing, and new mines will be needed to fill it. This project observes the current pipeline of copper mining projects, which are characterised by technical complexity (lower grades, deeper deposits, complex mineralogy etc.) but also environmental, social and governance (ESG) complexities. A common assumption in the mining industry is that a rise in copper prices will unlock these deposits. However, while most technical complexities are price sensitive and are likely to be overcome in favourable economic conditions, the influence of ESG complexities is more difficult to evaluate. CITATION: Lebre, E, Valenta, R, Kemp, D, Owen, J and Corder, G, 2018. Accounting for social and environmental complexities in mining project developments: the case of copper, in Proceedings Complex Orebodies Conference 2018, pp 39–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By R C. Morris

Secondary microplaty haematite in its variety of styles and generations is the defining component of the high-grade banded iron-formation (BIF)-hosted iron ores of the world that are dominated by martite (M; - haematite pseudomorphs after magnetite). The term microplaty haematite (mplH) was introduced during the CSIRO-AMIRA 1976-1994 iron ore program, and was used to differentiate the then main export martite-microplaty haematite (M-mpl H) ore types of Tom Price-Whaleback and Paraburdoo (Paleoproterozoic), from the newly exploited, more prolific supergene martite-goethite (M-G) ores (Mesozoic-Paleocene) of the Hamersley Province that are now the major Hamersley iron ore exports.Morris (1980, 1985) suggested that the most important genetic factor that distinguishes the two main ore types was regional metamorphism of Paleoproterozoic M-G ores at temperatures normally related to diagenesis (ca 80 - 100°C). As temperatures increased, mplH grew in goethite both spontaneously as well as by nucleating on martite and other pre-existing haematite. Because the conversion of goethite to haematite involves a ~27 per cent reduction in volume, the crystals probably grew within microvoids of their own creation, with iron transfer through water resulting from the process itself, a local hydrothermal process requiring no introduced hypogene fluids.Barley et al (1999) and Taylor et al (2001) concluded instead that oxidation of introduced siderite in hydrothermally metasomatised BIF ‘protore’ resulted in mplH + ankerite by reaction with heated meteoric fl uids. This postulated ‘protore’, still preserved locally at Mt Tom Price, was described during the CSIRO-AMIRA program as local post-ore BIF metasomatic residuals. These new hypogene-meteoric concepts for M-mpl H genesis have formed the basis for a range of varying local and international models that currently dominate the literature of iron ore.No valid petrographic data supporting the hypogene-supergene modelling was found but petrographic images of goethite-related mplH growth in a range of different environments are shown.

Jul 11, 2011

The United StatesÆ reporting standard for the mining industry for securities purposes is contained in the Security and Exchange CommissionÆs Industry Guide 7. It defines proven and probable Reserves using its own definitions, and prohibits the disclosure of quantitative estimates, for all mineralisation other than those two Reserve categories (though disclosure of Measured and Indicated Resources as quantitative mineralised material estimates is now informally allowed). Similarly, it restricts disclosure of value estimates to Reserves only, which SEC policy generally requires to be on an historic cost accounting basis. The SEC does not maintain a formal Competent or Qualified Person policy. In March 1999, the US-based Society of Mining, Metallurgy and Exploration (SME) released an update of its 1991 guidelines for definitions to be used in reporting of Mineral Resources, Reserves and Exploration Information, closely abiding by the 1997 CMMI recommendations. However, without SEC recognition, reporting under the SME and CMMI definitions is effectively barred for US companies. The SEC intends to adopt the International Financial Reporting Standards (IFRS) of the International Accounting Standards Board (IASB). This will occur within just a few years, when the convergence project for development of the IFRS has reached a satisfactory point. The US is the largest financial supporter and participator in IASB. The Extractive Industries Standard of the IFRS will likely terminate Industry Guide 7. However, the effect of this international replacement will likely be equally restrictive. This could possibly neutralise the benefit of a CMMI-based global reporting standard. SME, the US society encompassing the widest range of mining industry professionals, does not have a Code of Ethics. It has no mechanism for requiring members to abide by a professional standard. SME is presently looking into possible solutions for this deficiency. US-based professional societies that do have a binding Code of Ethics, generally cater to a single profession, and are not just mining industry related. The American Institute of Professional Geologists (AIPG) and the American Institute of Minerals Appraisers (AIMA) are examples. The SME is considering creating a subsidiary body with an enforceable Code of Ethics. To support a CMMI-based global reporting standard, competent persons will need to work across international borders. A standardised mechanism for qualifying and registering competent persons will be needed. National rules and laws must allow competent persons to easily enter countries to perform their work. State issued licenses are increasingly required for much of the work performed in the US mining industry by engineers, geologists and minerals appraisers (valuers). Such licenses are not required by the SEC for Reserve reporting in the US, may not be required for valuation of mineral properties under certain circumstances, and except for real property valuer licenses, they generally do not have a binding code of conduct. However, state licensing of professionals forms a substantial and increasing barrier to interstate trade in professional services, and can be a prohibitive barrier to professionals from outside the US. Any rationalisation of this confusing patchwork of regulations confronting US minerals industry practitioners will only occur as part of larger, national change, hopefully aimed at compliance with international standards and protocols. The US does not have a valuation standard aimed specifically at the mining industry. The Uniform Standards of Professional Appraisal Practice, the national valuation standards, often must be applied to mineral property valuation, but contains no specific instructions for minerals. The author has campaigned against development of minerals valuation standards proposed by US minerals institutes. Instead he encourages the mining industry worldwide to place its support behind the initiative of the International Valuation Standards Committee (IVSC) to include an extractive industries section in its International Valuation Standards (IVS). This should provide a global set of valuation standards for the mining and petroleum industry within two years. This addition to IVS will provide essential valuation standards reference support for the extractive industries financial reporting standard of the International Accounting Standards Board. The IVS has achieved a high level of acceptance in the developed and lesser developed countries of the world. It provides a comprehensive framework of Generally Accepted Valuation Principles for the valuation profession internationally, for valuation of all property or asset types. IVSC is effectively a sister organisation to IASB. The IASBÆs International Financial Reporting Standards (IFRS), previously known as the International Accounting Standards (IAS), reference and quote IVS in some instructions for determination of fair value. IVSC is a non-governmental organisation (NGO) member of the United Nations and maintains liaison with many important international economic, accounting and financial agencies, such as the OECD, IMF and WTO.

Jan 1, 2002

By Lewis RW, Tullemans FJ, Gallo JB

Gold mineralization at Kidston occurs in a semicontinuous zone near the margin of a large, late Palaeozoic breccia pipe. The pipe is ovoid in plan, funnel-shaped in cross section and straddles a contact between Proterozoic metamorphic and granitoid rocks which are intruded by a swarm of late Palaeozoic acid dykes. Rock fragments within the breccia pipe reflect the enclosing country rocks and mix in various proportions to form gradational lithological domains. Most of the gold is free and is located in the breccia matrix and in a set of inwardly dipping sheeted quartz veins which kink around the pipe margin. Sulphide minerals, dominantly pyrite, occur as disseminations in the breccia matrix and as aggregates in the cores of quartz veins. Hydrothermal altLration is pervasive within the breccia and is most intense in areas with the highest percentage of acid dyke fragments. Sericite and carbonate are the main alteration minerals. An empirically developed genetic theory for the formation of the breccia pipe and attendant mineralization involves magmatic and post-magmatic processes associated with the intrusion of a granitoid body to a shallow level in the crust. Economic evaluation of the deposit relied heavily on the results of diamond drilling. Both polygonal and geostatistical reserves were calculated and found to be in close agreement. Geostatistical reserves are considered to more closely reflect the tonnes and grade achievable during mining. Daily geological mine routine is strongly biased towards grade control allied with the practical aspects of open-pit mining. Tonnage/ grade correlations between ore blocks geostat- istically generated from exploration diamond core results and ore blocks generated from high

Jan 1, 1986

By F Shi, W Valery

WMC Fertilizers (WMCF) operates a Beneficiation Plant at Phosphate Hill in Queensland, Australia. The plant consists of two-stages of crushing, followed by a wet scrubbing and desliming circuit. Ore is then fed to a tertiary crusher and a milling/classification circuit, with the final product going to a swing-lift thickener and storage tanks. From the slurry storage tanks, the phosphate rock is fed to a horizontal belt filters which dewater the phosphate rock ahead of a hemi-hydrate phosphoric acid plant. The water soluble recovery of phosphate in the phosphoric acid plant is dependent on the moisture content in the filter cake, as this governs the wash water addition to the hemi-hydrate filters. Since commencement of operation, the moisture content of the filter cake fed to the phosphoric acid plant has been higher than design reducing the phosphoric acid plant recovery and at times reducing the throughput through the phosphoric acid plant. The moisture content in the filter cake can be decreased by reducing the generation of fines in the milling and classification circuit (classified as û38 micron material). This paper identifies the causes of fines generation in the Phosphate Hill beneficiation plant. It discusses the options that were assessed to minimise fines generation, and outlines the results to date of circuit changes undertaken at Phosphate Hill.

Jan 1, 2003

The Henty Gold Mine is a good example of a situation where conditional simulation and optimisation techniques may have useful impact on modelling of mineralisation distribution and ore definition. Much of the gold mineralisation at Henty is concentrated within an alteration zone which is both physically discontinuous and forms only a small fraction of the overall mineralised volume. The alteration units are mappable from diamond drill core and underground workings. Conditional simulation and optimisation techniques for ore definition have found considerable success in the open pit gold mining environment. For many reasons including computational efficiency, lack of consistent geological information, and lack of familiarity with ideas and methods among mine geologists, implementations of these methods in open pit mining have been comparatively simplistic. Modelling is commonly reduced to treating the sample data as a single geologic population. This paper discusses the application of the MP method (a particular implementation of conditional simulation and optimisation) to modelling the distribution of potential ore blocks in the Henty gold mineralisation. The approach allows the mine geologist to model both the spatial geometry of the alteration types and the gold grades associated with each alteration type in a single process. Options allow the geologist to include or exclude underground geological mapping and face sampling depending mainly on the abundance of drill hole sampling and the quality of the face sampling. An optimisation algorithm based on maximisation of profit from mining is used to assist in ore definition.

Jan 1, 2000

By Riley S. J

Ranger Uranium Mine is located within the Alligator Rivers Region of the Northern Territory of Australia and surrounded by the World Heritage listed Kakadu National Park (Figure 1). The mining operation is currently producing about 1500 tonnes of uranium oxide annually, as well as considerable volumes of waste rock, low grade ore and tailings. The rehabilitation of the project should ensure that the radioactive mill tailings and other contaminants remain contained for at least 200 years, as required by the existing guidelines (Commonwealth of Australia, 1987). The present uranium mining operation is regulated by the Northern Territory Department of Mines and Energy who must refer to the Environmental Requirements when considering regulatory options. These Environmental Requirements were agreed by the

Jan 1, 1994

The perception of New Zealand as an exploration destination has improved compared with other countries. There has been a realisation that New Zealand's potential is greater than previously thought. Other countries are not as attractive as before, and explorers are looking at alternatives that are geologically prospective and politically stable.   New Zealand is regarded as geologically prospective, especially for gold, with potential for world class deposits. It is also prospective for other metals, coal and industrial minerals. New Zealand is politically stable, and has an economy that is attractive to overseas investors. It is one of the least corrupt countries in the world, which overseas companies see as providing a high degree of certainty for investment.   New Zealand has good opportunities for investment in gold exploration at present. Otago has been the focus for new companies and is the favoured exploration location. Otago is regarded as very prospective, and hosts New Zealand's largest gold deposit at Macraes. There is potential for other similar deposits elsewhere in Otago.   The mineral industry previously had an excessively pessimistic view of New Zealand, which has resulted in little new investment in New Zealand for some years. Previous pessimism is turning to optimism, and there is increasing interest in New Zealand as an exploration destination by overseas explorers.

Jan 1, 1997

By P Tobar

The development plan (long-term plan) of El Teniente Mine, Codelco-Chile, includes 100 per cent primary ore, located at increasing depths, which may involve several difficulties related to the application of the current panel caving method, such as a high seismicity level, a coarse fragmentation and ore pass damage. Therefore, it is a strategic priority for the El Teniente mine, to design and to test alternative mining methods, at similar or lower costs to ensure an efficient and safe ore extraction. In this context, the Macrotrench method is developed, as a competitive alternative to the current method. The document describes the panel caving method, the experience achieved in the primary ore exploitation from the geomechanical point of view. It also describes the æmacrotrenchÆ method as an alternative to the current exploitation method. Finally, the comparative advantages of macrotrench in relation to panel caving are presented. The results obtained during the engineering stage include the following aspects:the mining design, the material handling, a geomechanical evaluation of the method, and a comparative analysis.

Jan 1, 2000

By A J. Cornah

"The mine geologist’s role in classifying ore from waste during grade control represents a critical link in the mining value chain. Any improvement in the ore/waste selection success rate (thus reduction in misclassification) which can be delivered by the mine geologist represents a value proposition. Improvement achieved without additional operating cost (for example extra drilling and sampling) will directly and immediately add value to the mining operation and therefore clearly must be pursued. Such improvement may be leveraged from existing resource drilling data which are typically less numerous but better quality than the grade control data. They are usually excluded from grade control estimates (termed the ‘base case’ approach here) because of the differences in quality.Various specialised geostatistical tools are available to account for differences in precision and accuracy between data sources during spatial estimation. This paper uses a conditional simulation (CS) case study to assess the benefit of integrating resource data into grade control estimates through ordinary kriging (OK) of pooled data sets, cokriging (CK), and ordinary kriging with variance of measurement error (OKVME) when the grade control data are:unbiased but increasingly imprecisebiased and increasingly imprecise. The premise assumed is that the resource data are unbiased and precise.The paper demonstrates that, if appropriately handled, resource data may be used to improve grade control estimates and thus improve ore/waste selection success without additional operating cost. Where grade control data are imprecise but unbiased it is recommended to integrate resource data using OKVME. This re-appropriates kriging weights from less precise to more precise data locations and improves the grade control estimation precision compared to the base case; it consequently provides an improvement in the grade control selection success rate. If grade control data are associated with significant bias, integration through CK is recommended as the biased data are zero sum weighted. CK consequently provides an unbiased estimate with some improvement in estimation precision compared to the base case and consequently improvement in the ore/waste selection success rate.CITATION:Cornah, A J, 2014. Incremental improvement of grade control models using resource data, in Proceedings Ninth International Mining Geology Conference 2014 , pp 387–396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

As the surrounding environment continues to change and evolve, mine managers face a changing climate of expectations. TodayÆs mine managers must juggle competing pressures to deliver sound social, environmental and economic results. Leadership is a fundamental tool for the effective mine manager. Whilst mine managers require solid technical and operational skills, importantly the manager must be able to engage a workforce, build and retain employees and seize opportunity for growth and development when presented. An important tool for engaging employees in the business at Rio Tinto Aluminium is the business improvement programme. At Rio Tinto AluminiumÆs Weipa mine, the business improvement methodology Six Sigma is used to deliver measurable, sustainable outcomes for the business. The next step in Rio Tinto AluminiumÆs improvement journey is to implement Lean Manufacturing at all managed operations. The operating environment for mine managers continuously evolves and effective mine managers must be flexible and adaptive to meet challenges. Governance and regulation constantly change in an environment of commodity cycles and finite resources. This increases pressure on the economic return achieved by the operation. As such, effective mine managers must be aware of and manage the operating environment û the broader, issues-based environment not just the immediate day-to-day responsibility of mine managing. This includes delivering on safety, community and environmental priorities. At Rio Tinto Aluminium, part of managing the business is via investment in the area of social partnerships to engage employees and the broader community in Rio Tinto AluminiumÆs commitment to sustainability. The Future Reef partnership entered with the Great Barrier Reef Research Foundation in 2005 forms an important part of Rio Tinto AluminiumÆs climate change strategy. This four-year, A$1 million investment funds programmes looking at the effect of ocean acidification on the Great Barrier Reef. The partnership is a unique example of industry and science working together on an area of mutual and national concern. Modern mine managers require a broad set of skills to effectively deliver outcomes. TodayÆs mine managers must make innovative and courageous responses to determine todayÆs strategy for tomorrowÆs future.

Jan 1, 2006

By C Woodfull, S Munroe

Geological uncertainty is reduced by improved understanding of the relationship between regional-scale geological basement features (structure, composition, depth) and known local structural risk (such as recognised structural hazards at the mine). Coal mining and exploration entities can be more efficient and effective in managing geological risk at a range of scales. A more efficient and effective performance in forward interpreting and managing geological risk will result in a more efficient and effective exploration and also incremental or even significant mining cost improvements. In order to improve the understanding of basement features, a new 4D regional structural/basin framework for the Sydney Basin and the eastern part of the Gunnedah Basin has been constructed to provide primarily coal exploration and mining with a more integrated geological framework for ongoing subregional to mine-scale geological risk based studies. The model has been developed from a range of available regional geophysical and geological datasets, of variable detail and reliability, which have been brought together to generate a more robust structural and tectonic model than could be generated with any one single dataset. An initial regional structural model for the Sydney Basin was constructed in 2003 and an update to the model was released in 2005 (SRK Consulting, 2003; 2005). The development and ongoing refinement of the model was undertaken with financial and data support from a number of coal mining industry, gas exploration and government organisations. Prior to, and following the development of the regional structural/basin model and associated Information Base, a number of more area-specific studies have been completed, using the æbasement upÆ assessment approach. The methodology for developing comprehensive structural models, from the basement up, is outlined. The approach can be applied at a country-wide, regional or lease area scale. Case examples of where this approach has been used as an effective and efficient method in improving geological certainty and as a predictive tool to help manage geological risk are also presented.

Jan 1, 2006

This paper discusses the potential role of underground space and tunnelling in urban planning in Australia. The paper gives examples of the infrastructure and commercial applications of underground space which have been effectively used overseas but have been slow to be considered as a part of urban planning in Australia. In particular, the paper looks at underground quarrying and underground commercial development and their potential use in the urban environment. Existing sites and potential sites for quarrying and/or commercial use have been classified using a system developed by the author. Underground quarrying may provide some solutions for planning problems involving sand and aggregate supplies, waste disposal and other uses. Commercial development involving underground excavation may be accepted if the cost of underground commercial development can be shown to be equivalent to the cost of above ground development. The paper concludes that one role of the underground construction industry is to promote tunnelling and underground space amongst architects, town planners and planning decision-makers. The Australian Underground Construction and Tunnelling Association (AUCTA) and the Australian Society for Trenchless Technology (ASTT) should be instrumental in actively promoting the use of underground space in society.

Jan 1, 1999

By A J LYNCH

It was Harold McMillan, Prime Minister of England 30 years ago, who used the phrase "The Wind of Change" to describe political events in Africa in his day. So well did this phrase capture the spirit of the time that it echoed around the world, and the echo has never stopped. Change is the constant factor in the society in which we live and everyone of us has had experience of the effect which it has had on our professional and personal lives. Change will not stop, it will continue at an increasing rate and the questions we must answer are how do we prepare ourselves to meet the challenge of future change and how do we take advantage of the opportunities which it will bring? It is these questions which I wish to discuss in this address.

Jan 1, 1989

By M I. Pownceby, J Manuel, S Suthers, A Poliakov, E Donskoi, N Ware

"The mining industry is constantly seeking methods for optimising the exploitation of mineral resources, such as iron ore, in a sustainable and eco-efficient manner for economic and social benefit. When faced with resources that have mineralogical or textural complexity, poorer grades or geological variability, it is particularly important to apply a comprehensive geometallurgical approach to the development of the mining operation, from resource definition through to processed product. Integral to this approach is the quantitative characterisation of representative samples across the whole orebody.A key factor that associates the geological characteristics of iron ores to their processing response is ore texture. While the classification of samples on the basis of chemical or physical properties alone is often not sufficient to predict their processing behaviour, classification and quantification of texture types can be effectively correlated to metallurgical performance in processes such as blending, beneficiation, pellet making, sintering and ironmaking. This paper describes some of the research conducted by CSIRO pertaining to the design and rationale of a texture-based classification system for Australian iron ores; some of the tools developed and used to apply such classification; and the application of the generated data to quantifying, modelling and predicting sintering behaviour and performance in the blast furnace.CITATION:Suthers, S, Pownceby, M I, Manuel, J, Ware, N, Donskoi, E and Poliakov, A, 2016. Geometallurgical Characterisation of Australian Iron Ores – from Ore to Processed Product, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 351–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S Walters

The emerging discipline of ‘geometallurgy’ is not new but is becoming increasingly recognised as a discrete and high-value activity. Geometallurgy involves a quantified and spatially constrained approach to ore characterisation in terms of relationships to critical processing performance behaviours. A key outcome is enhanced economic optimisation of mining and improved risk management tools.Industry recognition of the need for large-scale, integrated research to support this emerging area resulted in commencement of a major ongoing initiative in mid-2005. The AMIRA International P843 ‘GeMIII’ project (Geometallurgical Mapping and Mine Modelling) is a cross-discipline collaboration involving a number of world-class research organisations supported by over 20 industry sponsors.The project is delivering integrated tools and methods which link intrinsic rock characteristics to prediction of mineral processing performance. These indices must be capable of spatial distribution in 3D resource models and incorporation into mine planning and optimisation. A key aspect is provision of new cost-effective tools and methods which can provide the large numbers of measured and estimated data points required to undertake effective modelling and spatial distribution. The integrated methodology and enabling technologies being developed through the ongoing AMIRA GeMIII project are outlined, together with implications for supporting industry best practice.

Sep 5, 2011