Search Documents

Three key areas of C.I.P. plant design, viz. leach- ing time, adsorption and the gold loading on the carbon, are discussed and illustrated with examples. The need for accurate pilot plant data for use in assessing and optimising design is emphasized. This approach should minimize capital and maximise return on capital. It is demonstrated that, as regards adsorption, economics favours short retention time, high gold loadings and mechanically agitated, draft tube reactors. INTRODUCTION Little attempt appears to have been made in Australia to design the present generation of C.I.P. plants to achieve an economic optimum. Most would, seem to have been based on pre- liminary leaching data, gold extraction and value and rule of thumb which, in general, has led to over design and over capitalisation. An essential step to effective economic design is a comprehensive pilot plant study to establish definitive operating parameters, yields and reagent costs. In most cases the cost of developing this data will be more than offset against capital savings in plant; the operating profit should be increased substantially, and profit is maximised for known

Jan 1, 1982

During the past 18 months a rock mechanics project has been in operation at Renison Limited. The project was established to identify and investigate key problem areas that would affect future production at the Renison mine. An in-house approach was adopted, using shall compact equignent, to investigate ground behaviour. Information on the rock stress field was considered to be particularly important for an understanding of ground behaviour. A high horizontal stress component exists, which enables large flat dipping spans of hanging wall to be opened up, with support being provided by post pillars. The amount of support provided by these post pillars has been found to be low.

Jan 1, 1982

By Sen G

An amount of explosives, whether it be cylindrical, spherical, etc in configuration, with a hollow cavity in one face or end is known as a hollow or shaped charge. When this charge is initiated, a focussing of explosive energy will occur within this cavity. This focussing, or concentration of detonation products creates an intense localised force greater than just the simple detonation of a conventional explosive, (without a hollow cavity). If this hollow cavity explosive is directed against a target material this concentrated force is capable of creating a deeper penetration than the same amount of explosive without the hollow cavity. If a metallic liner material is used in the hollow cavity, upon detonation of the explosive this liner will form into a high velocity penetrating jet. Depending on the explosive type and the liner material's configuration the jet tip can travel up to 10 km/s. Linear shaped charges were developed using the abovementioned shaped charge concept but instead of being formed about an axis, they are elongated and constructed along the principal axis. Therefore instead of creating a narrow circular penetration jet, it forms a thicker planar cutting jet ideal for linear cutting purposes. Using Linear Shaped Charges (LSC) for pre-splitting is expected to result in more accurate directional fracture propagation, while minimising lateral micro fractures in the surrounding rock mass which is required to remain undamaged.

Jan 1, 1995

INDEX OF CONTENTSComposition of the Brown CoalsIntroductionComposition as minedComposition from drilling explorations:Latrobe Valley Area, East Gippsland, Welshpool-Alberton West Area, Altona-Bacchus Marsh Area, Lal Lal Area, Dean's Marsh Area. The Coal Constituents:Vitrain, fusain, detrital coal, resin, Sulphur, types, distribution, Ash, composition, sulphur, phosphorus, chlorine,,titanium, vanadium, distribution in seam, fusibility, source, mineral ash, chemical ash Bitumen, tar. Factors causing Variation in Composition:Pressure of overburden, moisture content, carbon, hydrogen, nitrogen, oxygen, calorific power, density, compression by warping, abnormal moisture, initial differences in vegetation, conditions of sedimentation, weathering before re-burial.Summary and AcknowledgmentsList of References

Jan 1, 1945

By Anderson K

In 1991, the first horizontal raise drill hole in Australia was successfully completed by Australian Raise Drilling Pty Ltd (ARD) at the Perseverance nickel mine of Western Mining Corporation's (WMC's) Leinster Nickel Operations in Western Australia. At that time, WMC were experiencing considerable difficulties in developing the horizontal drill drives through the orebody using conventional drill and blast techniques. Following the success of the initial hole, a further two holes were drilled as part of the evaluation program. The technique has proved so successful that it has been accepted by WMC for on-going development of drill drives at Perseverance.This paper describes the program. It relates how the project evolved, the modifications that were required to the equipment used, the performance experienced during the program and the future of the method in this and other applications.

Jan 1, 1993

The Tick Hill Gold Mine is situated approximately 110 kilometres south of Mount Isa, and 14 kilometres north of the township of The Monument. It was discovered in October 1989 by Mount Isa Mines Exploration in an area which had been targeted as high in potential for copper-gold mineralization.A mining lease application was made in March 1990. Mining, and the construction of the plant and infrastructure, began'in early August 1991 after the lease was granted on 20 June of that year. Commissioning of the plant began in December 1991, and the first gold was poured on site on 31 December 1991.The development of the underground mining operation commenced in January 1992 with the drilling of the ventilation shaft. The access decline was started in March of the same year, with the first ore produced from underground in August.

Jan 1, 1993

The originally estimated mine life at Kidston (starting 1984) was 12 years. Through a continuing process of re-evaluation and improvement in the operation and by expanding the geological knowledge in the region, the mine life has been considerably extended. With falling grades and harder ore, the additional reserves have come with increasing risk - not only in an economic sense associated with diminishing profit margins but also operationally, requiring innovative milling technology and geotechnical designs to provide a lower cost environment for continued profitable mine production.

Jan 1, 1994

By Granholm S

The current emphasis within the mining industry to reduce the cost of production has stimulated interest in the field of maintenance and operational reliability of capital intensive mining equipuent. The failure consequences of these machines have major safety and economic implications for a mine operator. The reliability centered maintenance (RCM) approach has been found cost effective for equipment maintenance and for achieving high level system perform- ance by many organizations such as airline, military, chemical, process and manufac- turing industries. In this paper an attempt has been made to describe in brief the basic concepts of a RCM approach, the methods of RCM analysis and its cost effectiveness for maintenance of equipment. Since this approach is comparatively new for the mining industry, suitable examples are given to illustrate the case.

Jan 1, 1988

LESLIE BRADFORD GOLDEN JUBILEE ORATION "Not only a metallurgist but a scientist of the highest order" Leslie Bradford and the Australian Metallurgical Industry

Jan 1, 1987

By Sehic O. A

Geology can be the root of evil or a source of bliss; there is a choice; to ignore geology is at a mine's peril.Risk can be minimised and profitability maximised by the application of a detailed understanding of geology, alteration, structure, mineralogy, chemistry, fabric and texture.Geology is dynamic, not static.The impact of geology is pervasive.The integration of ore quality control with grade control is one strategy for improving the utilisation of both the mineable reserves and existing plant and equipment. Grade maintenance is but one constraint on the problem of how best to blend the ore. Other ore characteristics such as mineralogy, hardness for grinding, and pulp fluidity or density for slurry size classification can be included to explore alternative blending Strategies.

Jan 1, 1993

By Wiechers HNS

In China the hydrogeological type of solid mineral deposits can be divided into A. Mineral deposits with fissure water; B. Mineral deposits with pore water; and C. Mineral deposits with karst water. The hydrogeological conditions of mineral deposits with fissure water are relatively simple with the exception of a few cases. Mineral deposits with pore water are few but great amounts of ground water can be encountered in the mine accompanied by floating sand or slope failure during the exploitation. Mineral deposits with karst water are complex in their hydrogeological conditions. Enormous inrushes occur frequently in the mines of north China; Karst collapses are a serious matter in the mines of the south; Subterranean river and conduit systems are often encountered in the southwest. This paper will give full discussion on these features and put forward a way of combating and controlling the groundwater problem in accordance with type and feature.

Jan 1, 1988

By Chappel R. A, Fishburn B. R

The Eastern Distributor Tunnels - the first major road tunnel project in Australia - are the preferred solution to traffic congestion problems, when compared with alternatives, in this inner urban environment. This is because of the reduced impact on residential housing, the improvement of the existing environment, less restrictions on future developments, and a reduction in noise and pollution. Developments leading to a tunnelled solution, traffic needs and reasons for route location are discussed. Criteria for design of tunnel alignments and geometry are described, including the restraints imposed by surface connections on profiles and grades resulting in low rock cover at tunnel portals. The main geotechnical restraints are a major weathered dyke at the shallow large span underground fork and the weathered Ashfield Shale capping the Hawkesbury Sandstone at a portal. Rock cuttability and excavation methods are discussed. Roadheader machines are the most suitable for the varying shallow arched cross sections required and the tunnel lengths involved but the use of blasting in special situations cannot be ruled out. Initial support for the major tunnel lengths will be provided by rock reinforcement in conjunction with shotcrete. Steel ribs are proposed in areas of low cover and weak ground. Final support will comprise an insitu concrete lining. Construction concepts and special tunnelling methods required at the shallow underground forks and tunnels are described.

Jan 1, 1987

By Thomas CG, Armstrong GJ, Lynch KS

A small glass walled pot grate has been used to simulate drying of iron ore pellets in a travelling grate plant. This equipment has enabled the effect of decreasing grind and de- creasing pellet bulk density on plant production to be quantitatively predicted. These predic- tions are compared with plant experience. The use of the laboratory simulator in comparing the effect of various additives on plant production is also described and substantial improvements in both the goethite and free-water drying periods are predicted.

Jan 1, 1972

Acupan is considered to be an intrusive centre as several igneous phases have been emplaced in the vicinity of the mine over the past 8 Ma. They include the Lucbuban gabbro, Virac granodiorite, Ampucao dacite porphyry (ADP), Hartwell plug, Itogon plug and the multi-phase Balatoc diatreme. These intrusives have high-K calc-alkaline affinities and are grouped together as the Virac Complex.Porphyry-style mineralisation formed during the final crystallization of the ADP in the late Pliocene, with the deposition of two vein stages from high-temperature hypersaline magmatic-hydrothermal fluids. K-silicate alteration halos surround the first stage of veinlets (stage I); they are surrounded in turn by a propylitic assemblage. White sericite and/or intense propylitic halos envelop the second stage of veinlets (stage II) and grade into a weak nrnnvlitir accPmht o

Jan 1, 1990

In early 1985, Bougainville Copper Limited commissioned an automatic truck despatch system to control its fleet of 44 trucks and 9 shovels. Productivity gains in the past have been the result of increasing equipment size then improving availabilities. The emphasis now is on improving the use of that availability and in particular for trucks, in reducing non-productive truck movement. A batch allocation computer based truck control system had been in operation since 1978, so to achieve the desired improvements it was necessary to move to an automatic dynamic control system. A description of the system installed is given, together with a review of how the project was engineered, the problems encountered and the results achieved to Date.

Jan 1, 1986

As a result of high fuel prices and substantial haul distances or vertical lift from pits, the development of large inpit crushing and conveying systems at many open pit operations has occurred over the last decade.The basic criteria that has to be met is that the material is reduced in size to be conveyable. Generally this requires a top size of less than 300 mm.

Jan 1, 1992

Kidston Gold Mines Limited (70 per cent Placer Pacific and 30 per cent Public Shareholders) has been mining the Wises Hill Pit since late-1984. The Wises Hill Deposit is a large low grade gold deposit and as such is highly sensitive to economic parameters. The uniformity of the orebody has allowed a bulk mining method to be used, with minimal dilution. Total reserves defined to-date are 64 160 OOOT at a grade of 1.60 g/t gold. Mineable reserves remaining as of January 1992 are 36 357 OOOT at a grade of 1.28 g/t gold.Mining investigations to reduce the impact of lower gold prices, the effect of decreasing headgrade and increasing mining costs have focused on wall steepening.

Jan 1, 1992

By Umar N

Traditional exploration has been undertaken by both local and overseas experts to discover tin deposits in Indonesia over almost 300 years. Indonesia is part of a tin belt which runs from Myanmar in the north through Malaysia to Singkep, Bangka, and Belitung islands in Indonesia in the south. The discovery of alluvial tin deposits is becoming harder as the more obvious geological targets are exhausted and topographical conditions become more difficult. New approaches are required to sustain successful exploration. There are indications that tin deposits can be found at depth on-shore as well as off-shore. These deposits are found associated with tough clays. On-shore tin exploration is hampered by swampy areas, while the off-shore search is often affected by difficult sea conditions. These factors lead to increases in the cost of exploration as well as the cost of subsequent production. Tin price fluctuations and environmental issues are also of major concern in the planning of the future operation of tin mining in Indonesia.

Jan 1, 1996

By Wygralk A, Hallenstein CP

On a world scale, many Mid-Proterozoic fluvial sediments are prospective for low grade, large-tonnage gold deposits. A significant area of the Northern Territory is covered by such Mid-Proterozoic sediments, the gold potential of which has been barely tested. The geological knowledge of these sediments is summarised. The Westmoreland Conglomerate, the basal Mid-Proterozoic formation of the McArthur Basin, has been subjected to detailed sedimentological studies in order to determine the paleoenvironments and to assess the possibility of paleoplacer occurrences. The results indicate that the sandstones and conglomerates of the formation were deposited by braided rivers and debris flows as an alluvial fan which originated in source areas to the north east. The formation contains several upward-fining cycles of sedimentation, which are related to repeated periods of uplift in the source areas. The formation of placer-type gold occurrences is possible in such depositional environments. Very limited heavy mineral sampling has indicated a cassiterite- wolframite-gold suite in the sediments of the Westmoreland Conglomerate. Disconformities at the base of sedimentation cycles are deemed to be the most likely sites for large-tonnage paleoplacer concentrations.

Jan 1, 1984

Many stress measuring instruments use overcoring stress-relief principles but adopt different sensing techniques. Every technique is subject to certain limitations of rock types and conditions. To investigate the performance and reliability of the instruments in field measurement, a simple and practical approach has been developed to allow comparable laboratory results to be obtained which simulate in-situ rock and stress conditions. Four commonly used devices, the USBM deformation gauge, the CSIRO HI cell,the CSIR triaxial cell and the UNSW SI cell were thoroughly tested in the laboratory. Some conclusions have been drawn as to their suitability and reliability in different field conditions. Recommendations are provided for the choice of an appropriate technique for a given rock type and condition. A new thin-wall cell that overcomes the disadvantages of earlier devices has been developed and tested. Its laboratory performance shows that it has good prospects.

Jan 1, 1990