Search Documents

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and*pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anortho- site layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spinel-bearing meta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the Goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, Ni, etc. liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

By Erceg MM

The Waft River gold deposit is hosted by low grade metasediments which have been intruded by a dacite/andesite porphyry complex. Wafi River is classified as a high sulphur, epithermal type gold deposit having: a high sulphur content, a close association with calc-alkalic igneous rocks, zoned advanced argillic and argillic alteration, and enargite group minerals. Gold occurs as minute inclusions in pyrite and pyrrhotite within intermediate dickite/kaohnite - interlayered illitic clay alteration zones. Central leached silicic, alunite and pyrophyllite zones and peripheral chloritic zones are low in gold. The gold mineralisation at Wafi is interpreted to have been predominantly caused by mixing of hot upwelling acidic magmatic mineralised fluids with cool, neutral meteoric/hydrothermal fluids within permeable sediments. Locallised high grade breccia zones are encountered within the porphyry. An initial resource in excess of I million ounces Au has been defined.

Jan 1, 1990

By J Boland

Polycrystalline diamond compacts (PDC) have been widely used as cutting elements in the drilling tools for the oil, gas, civil and mining industries because of their faster penetration rates and longer bit life. US Department of Energy reports that PDC bits account for more than one-third of the total footage drilled worldwide (US Department of Energy, 2004). However, non-thermally-stable diamond composites (NTSDC) have seldom been applied to geothermal drilling, since premature failures of such PDC cutters have been observed in hard rock formations. Several factors need to be considered to prevent premature failure of cutters and improve cutting performance when using PDC-based bits and other rock cutting tools. The first set of factors consists of the strength, density, stiffness, toughness and thermal resistance of the PDC and the rock. A second set relates to the complex behaviour of the bonding between the PDC cutter and the bit matrix, or the pick and the pick holder, which is vital in maintaining stable, reliable and durable adhesion of the cutters to their hubs. Finally, based on a better understanding of the cutting processes, the formulation of a predictive model would assist in further development of cutter design.

Jan 1, 2004

By Taylor G. H

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopical techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relat- ing their inherent properties to properties such as volatile- matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used coimierciallyti,

Jan 1, 1969

By Bowra N

Working capital is best described as money that must be supplied from a company's treasury to buy inventories for raw materials and finished products and to provide credit to customers who have not yet paid for delivered products. Working Capital requirements for resource projects are to a large extent, dependent on specific characteristics of the projects concerned. Important variables are the nature of the project and speed with which sales can be realised. The project's location is also important as this will influence inventory levels. Working capital requirements have a time profile, the present value of which can represent a significant portion of a projects overall capital needs. A significant component of a project's working capital is not readily recoverable or able to be reassigned should the project fail or be deferred.

Jan 1, 1986

By C Pypno, P Nowakowski, T Opasiak, C

Belt conveyors are machines for continuous transport with most applications in mining industry in Poland. This is a result of simple construction and cheap operating costs. But conveying materials by belt conveyors are often in the powder state (eg small coal, gypsum, etc) and during the transport there is a possibility of polluting the environment around conveyor route. A good solution for this problem is the pipe conveyor, where a belt is closed on the route in circular shape and flat on unloading point. Another problem which is indicated in the paper is dusting on the belt conveyor boosters. In Poland a new solution of booster has been designed, whereby dustiness of transportation powder materials is reduced by up to about 90 per cent.

Jan 1, 2003

By R Piper

The Yabulu Nickel Refinery commissioned in 1974, processes lateritic ore via a modified Caron process to produce high quality nickel and cobalt products. The Greenvale orebody provided the sole source of feed to the plant until 1990 and with well-blended mineralogy, it resulted in stable and predictable plant performance, allowing the operating focus to be on reducing energy consumption and increasing ore throughput. This approach provided better economics than pursuing increased reduction efficiency. From 1990, increasing quantities of lateritic ore were imported from Indonesia, Philippines and New Caledonia. This introduced considerable variation in ore blends and instability in plant operation but also provided the opportunity to treat higher grade ore blends which yielded higher reduction efficiencies. Ore reduction is conducted using 12 Herreshoff multiple hearth reduction furnaces, using heavy fuel oil as reductant. The æROASTERÆ Project was approved in November 2000 with the primary objective of improving Nickel reduction efficiency by: Stabilising Roaster Operation via a structured program including focused maintenance efforts, capital equipment upgrades, new process measurements, process re-design and improvements to operating skills and process troubleshooting. A structured technical program including laboratory and plant studies using one plant furnace as a pilot unit to develop improved knowledge of how the reduction process proceeds in the Herreshoff furnace. Armed with this knowledge, optimised process conditions and a reduction process model were developed contributing to a significant demonstrated reduction efficiency improvement. Technical input to the project was provided by QNI with Hatch providing the engineering and project management for the $8.5 M capital work. Execution of the work included extensive consultation with the plant operators and close cooperation between the Hatch project team and QNI operations personnel ensuring installations were completed with minimal production disruption. A strong focus on safety management resulted in a number of brownfields project relevant safety initiatives being implemented resulting in project completion without a serious injury.

Jan 1, 2002

By A Tomsett, J Rutter

Ore control systems at Ridgeway have been designed to deliver gold and copper metal production through focussing on the ore characteristics that impact on mine and mill performance and ultimately metal delivery. This is achieved using data collection and management systems which allow data to be collected digitally with æat captureÆ validation routines. This data forms the basis of forecasting systems which aim to accurately assess local in situ and drawn ore characteristics. Physical attributes of ore such as draw characteristics, brow conditions and visual grade estimation are rountinely recorded. Ore tracking and accounting systems monitor gold and copper grade, copper mineralogy, host lithology and ore sizing. These have material impacts on concentrator throughput and metal recovery. Routine reconcilation and check sampling allow calibration of these systems.

Jan 1, 2002

By Okura T, Hino J

Coal utilization for copper flash smelting in Japan was initiated due to the sudden upheaval in the price of oil in the last ten years. A major portion of the heavy fuel oil has already been replaced by coal resulting in a corresponding decrease in energy costs. In addition to energy cost savings, an interesting metallurgical phenomenon was observed in flash smelting operations. Unlike oil combustion, coal is not burned completely in the shaft. A considerable fraction of coal particles remain on the surface of slag and are burned at the settler. Chemical investigation has shown that oxygen potentials at the settler have consequently decreased, bringing the slag and matte phases into reducing conditions, thus oxidation and reduction can coexist in one flash smelting unit. As a result, a decrease in magnetite and copper contents in the slag, elimination of furnace hearth build-up and dissolution of intermediate layer between matte and slag have been observed. In general, these led to improvements of furnace operations. However, thermodynamic investigations have shown that some minor elements such as As, Sb, Bi and Pb concentrate from slag to matte. Results evaluated on the basis of thermodynamic data relatively agree with practical observa- tions. Consequently, for coal utilization in flash smelting operations it will be necessary to control oxygen potentials from the stand- points of copper loss in slag and minor element Distributions.

Jan 1, 1987

Epicentres of recent shallow earthquakes in the region (3-12¦S, 126-150`E) were plotted to identify the various plate boundaries in the region, in particular the southernmost one marking the northern edge of the Australian plate. New and published fault plane solutions were examined to determine the style of faulting and state of stress along the Australian plate boundary. From east to west the boundary is first a subduction zone along the Solomon Islands, then a spreading centre across the Solomon Sea, a zone of compression and left lateral strike slip along the Papua Peninsula, almost pure thrusting across the centre of New Guinea and lastly left lateral strike silo through Irian Taya to the outer Banda Arc. The principal stress is very consistent, trending NW to NNW in a near horizontal plane, from the triple junction of the Pacific, Solomon Sea and Australian plates in the east to the Banda Sea in the west. Only along southern Solomon Sea plate margin which is a divergent boundary, is the stress different in type and direction.

Jan 1, 1987

By Thompson AG, Cadby GW

The New Austrian Tunnelling Method (NATM) is a proven concept for the safe and economic construction of underground facilities. This is especially true for tunnelling activity where changing ground conditions are often encountered. However, the principles central to the NATM have gained only limited use within Australia, presumably due to the measurement process inter- fering with tunnel driving and the cost associated with instrumentation and interpre- tation expertise. The design and operating principles of two basic instruments are explained together with laboratory simulated test results and suggest- ions for use in an integrated NATM style approach to underground excavation and construc- tion. The two instruments monitor load in rock reinforcement and deformation in rock or primary and secondary linings. The instruments may be fitted with a miniature display module which outputs the measured parameter in engineering units directly. The design of the sensing components allows the instruments to be installed in various configurations suitable for routine performance monitoring, quality control, support element testing or detailed investigations. The display module which reduces the need for instrumenta- tion expertise should suit contractors and allow performance data to be obtained which quickly may be used to modify support procedures to suit ground conditions. When complemented by convergence measurements the devices enable most facets of the NATM to be implemented.

Jan 1, 1987

The Northwest Territories (NWT) of Canada has emerged as a major new province for diamond mineralisation in less than three years. This is primarily the product of a diligent search in the form of a scientifically based exploration effort. However other factors, including positive aspects of the business and the legal environment have also been identified as assisting the exploration process. In my view these have increased the likelihood of diamond mining becoming a major new industry for Canada. The supportive role of various government agencies has been important. In addition, the character of many of the joint venture deals that have been done has provided an attractive setting for the capital intensive evaluation and development work that is now required to bring the diamond discoveries into production. Perhaps of equal importance is that with the recognition that is being given to the success of the NWT diamond ventures, Canadian explorers are continuing to attract new risk capital for further exploration. This paper attempts to model and quantify the probability of exploration success translating into successful mine development.

Jan 1, 1994

Current problems in predicting sub-surface strata movement and fracture development due to longwall mining have highlighted the need for more accurate, dependable methods of physical modelling of rock mechanics problems which are beyond the capabilities of current mathematical techniques. Physical model studies of the caved zone above the working faces up to the base of a water source are of importance in attempting to understand changes in mass permeability due to induced fracture zones and the resulting ground water conditions. Turkey's most important supplies of coking coals are to be found within the hard coal resources of the Black Sea coast. Coal seams up to 9 metres thick, dipping at angles as steep as 90 degrees are being successfully mined at the Kozlu Mine. Since 1956, mining operations have been carried out under the sea in dry conditions. The undersea mining conditions of the Kozlu Mine have been investigated using scaled physical models constructed from artificial materials which satisfied necessary scaling requirements. Models representing the in-situ conditions were tested and the following extraction sequence was employed: 1. The Sulu Seam extraction 2. The Acilik Seam extraction (as two slices) 3. The Piric Seam extraction. The displacement of the fixed reference points were subsequently measured using a high precision photogrammetric technique and induced horizontal and vertical strains were calculated.

Jan 1, 1988

AT Broken Hill, N.S.W., where flotation is tbe final stage in concentration, the gangue minerals are discharged as an aqueous pulp, and water recovery from the pulp being essential, provision must be made for the clisposal of the solids and for the return of the clear water to the cemcentrating mill circuit. This water also contains an appreciable quantity of flotation reagents, and is more effective for flotation than supply water.In the development of a scheme for the disposal of large quantities of residues, several of the more important factors for consideration are:(a) Tonnage to be handled.(b) Grain size of residues and pulp density.(c) Dewatering of residues and return of clear water to mill circuit.(d) Possible uses of residues.-A varying proportion of sand residues is used for underground filling, and to a limited extent for yoncrete making and other engineering work.(e) Choice of a suitable dumping area. - Before deciding upon this area consideration will be given to possible future operations so that the dump will not be likely to interfere with any development which may be necessary. Again, residues dumped at the present time as worthless or...

Jan 1, 1927

By Yamada K, Abe H

Magnetic scanning type mass spectrometers have been given improved sensitivity with a large dynamic range and considerable resolution by the addition of a computer-controlled electric equipment. A mass spectrometer equipped with this newly developed electric system was applied to studies of the activities of liquid iron-silicon alloys and of liquid iron-phosphorus alloys at 1600¦C. The range of silicon concentration was 5.8at%-51.1 Si= at%, and values of ySi -3.1+0.15 and es 11.5 +1.5 were obtained. The concentration range of phosphorus was 1.3at%-5.7at% and a value of eP=7.3+0.1 was obtained.

Jan 1, 1980

By Chapman RL

A new process has been developed to remove the impurities copper, cadmium, cobalt and nickel from a zinc plant electrolyte by cementation on zinc dust. The process has been tested in the laboratory and in a continuously operated pilot plant. It has been found that cadmium, in the presence of small amounts of antimony in solution, assists the removal of cobalt. Cementation is conducted in two stages: the first stage for removal of copper with a small excess of zinc dust to produce a relatively high grade product, the second stage for removal of cadmium, cobalt and nickel by addition of zinc dust in the presence of anti- mony. The excess zinc and the cadmium present in the second stage cementate can be selective- ly recovered by slow leaching in spent electrolyte. Zinc dust processes in use elsewhere are described and compared with the present system for use in the Risdon circuit.

Jan 1, 1984

Following unprecedented high market prices for tin and gold in 1980, significant advances in both mining technology and geological knowledge took place in northeast Queensland. These led to a rapid growth in mining activity. Production of these traditional metals reached levels comparable to those of the heyday of mining activity at the turn of the century.Although tin and tungsten prices have since collapsed, the geological knowledge gained and significant discoveries made during the boom, have created a potential for mine development when prices rise again. For other discoveries which are not workable because of treatment problems, future technological advances are required to raise their potential.

Jan 1, 1990

By Miller J. D

The mechanism of adsorption of gold from alkaline cyanide solutions by carbon has been the subject of much research over the past decade. In this paper, the nature of the gold cyanide adsorption phenomenon is investigated, particularly with respect to carbon substrates and associated surface adsorp- tion sites.

Jan 1, 1991

Stressed steel cables, similar to those used in pre-stressed concrete, have been used for rock mass reinforcement, in civil engineering, for many years. This type of reinforcement has been attempted for open pit wall support, on several occasions, but has never gained wide acceptance as a practical approach because of high cost and complexity of installation in a mining environment. On the other hand, untensioned, fully grouted cable dowels (cable bolts) have gained wide acceptance for ground support in underground mining and it is perhaps surprising that this technique has not been used to a greater degree in open pit mining. The first systematic application of this technique in Australia was at the Mary Kathleen uranium mine in 1976, where it was spectacularly successful in maintaining steep stable walls in a jointed rock mass with unfavourably dipping structures. Cable bolting, and other techniques, are now being used to an increasing degree for wall support in both small and large open pits, for two basic applications: 1. stabilisation of potentially unstable sections of a wall, or 2. to allow steeper walls and reduce waste stripping volumes. In virtually every situation, wall rein- forcement has significant economic as well as technical advantages. The paper describes the development of the techniques, the mechanisms of wall support, the methods used, and discusses several case histories of its application to Australian open pit mines.

Jan 1, 1986

The Pike River Coalfield is located on the West Coast of the South Island of New Zealand near the top of the Paparoa Range approximately 45 km north east of the coastal town of Greymouth. The Pike River Coal Company Ltd (PRCC) is owned jointly by New Zealand Oil & Gas Limited (NZOG) and private investors.   The project has followed a long and difficult road towards project implementation which is now a reality with mine construction scheduled to commence in November 2005. The first stage of the project, the consent and land access process has been the most difficult. Resource consents for the project were first applied for, granted and appealed in 1998. A second round of modified resources consents followed a similar path in 2001. Following consultation with a range of parties including local and central government as well as the Department of Conservation, in March 2004 the Minister of Conservation granted PRCC access through Department of Conservation land. In October 2004, the Environment Court issued a Memorandum of Consent granting resource consents with conditions that had been negotiated between PRCC and the appellants.   The second stage of the project, investigation and design, commenced in December 2004 and was completed in June 2005 with the PRCC board ratifying the project capital and operating budgets. While the investigation and design work was proceeding, PRCC were also engaged in securing private equity and bank debt funding for the project. Formal Board approval to proceed with project construction was granted in September 2005 following completion of fund raising.   The project consists of a number of significant construction activities, namely: +        10.5 km of mine access road through previous logged and virgin rain forest; +        2.2 km of tunnel through metamorphic rock; +        a coal preparation plant about 8.3 km from the mine portal; +        an underground coal preparation plant; and +        a major slurry pump station, high and low pressure underground water supply systems to support hydraulic mining units and underground coal transport respectively.   Project construction is expected to be completed in April 2007 with completion of the ventilation shaft. Mine production will commence in December 2006 with coal from pit bottom development which will be carried out by the mine owner.

Jan 1, 2005