Search Documents

By A M. Mueller

St Helena tunnel is the centrepiece of the Pacific Highway upgrade from Tintenbar to Ewingsdale, abbreviated and commonly known as T2E. At the deepest point the twin tunnels run 45 m below the ridge line of St Helena Hill, located about 5 km west of Byron Bay. The tunnel breakthrough was achieved early in 2014 and the works for permanent lining will be completed in early 2015.Once the project will be handed over to the public in 2015, T2E will deliver a safer highway and uninterrupted traffic flow between New South Wales and Queensland. The design speed in the project area has been set to 110 km/h by the client Roads and Maritime Services (RMS), which will reduce the travel times between Brisbane and Ballina to just over two hours.The two tubes of the tunnel have been designed to accommodate three lanes in each direction with shoulders and walkways on either side of the carriageway. These requirements result in a huge cross-section of about 20 m width and an excavated area of about 210 m2.With the tunnel alignment being situated in basaltic rock, St Helena tunnel is conventionally driven. The selected excavation method was predominantly drill-and-blast with temporary support being installed immediately after the excavation. Despite the wide span of the tunnel, the geology allowed the tunnel perimeter to be supported by only rock bolts and a layer of shotcrete over the majority of its length.Due to environmental reasons one of the approval criteria of the project was that the tunnel must not have a detrimental long-term impact on the groundwater system within St Helena Hill. Consequently the tunnel has been designed as a fully tanked structure with a waterproofing sheet membrane installed on the temporary shotcrete.The permanent structure of the tunnel has to meet a 100-year design life and it is designed as a cast in situ concrete lining. Considering the water pressure on the lining the concrete is reinforced with a significant amount of bar reinforcement.The presented paper provides a more detailed explanation of the geology and the consequential temporary and permanent support measures together with the waterproofing system.CITATION:Mueller, A M, 2014. Pacific Highway upgrade from Tintenbar to Ewingsdale (T2E), St Helena Tunnel, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 419–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Ralph AM, Deakin JJ

A quantitative knowledge of underground mine ventilation requirements and conditions has become increasingly important, both to meet statutory requirements and to ensure high levels of safety and productivity within mines. The ACIRL Mine Ventilation System MINVENT was designed to provide a flexible means of analysing the behaviour of an underground mine ventilation system under a variety of conditions. It is not sufficient to rely solely on the analytical tools such as ventilation network analysis computer programs - these must be supported by the expertise necessary to conduct an accurate underground ventilation survey as well as experience of typical conditions to be expected in the evaluation of proposed extensions to a new or existing mine. When planning a new mine, the ventilation engineer can use the program to draw on a set of typical ventilation parameters, seam and proposed mining methods. These have been assembled as a result of numerous ventilation surveys conducted by ACIRL in New South Wales and Queensland.

Jan 1, 1983

Obtaining correct assays for gold determinations relies on the correct methods being chosen and the assayer being made aware of the mineralogy of the sample and its general origin. Usually when a geologist or metallurgist obtains "incorrect" gold assays the problem can be traced to poor communication between the geologist or metallurgist and the assayer.

Jan 1, 1986

Since 1969, a substantial number of geophysical methods have been applied in the search for porphyry copper and mesothermal type -sulpha-de deposits. These have assisted with geological mapping as well as the definition of various sulphide depos-its. The application of these methods at the Frieda-Nena deposits, Papua New Guinea, can be used as a case study for exploration in other parts of New Guinea.In 1993, Highlands Gold Limited carried out an intensive geophysical program over the Nena deposit. The methods employed included, CSAMT (controlled-source audio magneto-tellurics), airborne and ground elect-romagnetics, IP/resistivity and ground magnetics. The magnetic method was used as a regional mapping tool as well as a way of mapping alteration zones over both the Nena and Frieda River copper deposits. Electromagnetics, in part-icular FLAIRTEM, is a rapid reconn-aissance tool as well as a detailed mapping tool for the location of Nena-style massive sulphide deposits. IP/ resistivity is an expensive but most useful tool for mapping out Frieda porphyry copper style disseminated sulphides as well as Nena style deposits. It can be used to define drill targets in areas of difficult Access.a

Jan 1, 1994

By English W, Poppit I

COALEX Pry Limited operates two underground steaming coal mines on the western edge of the Sydney Basin near Lithgow, New South Wales. Baal Bone Colliery uses longwall technology for an output of over two million tonne/year while Clarence Colliery currently uses continuous miners and breaker line supports for an output of two million tonnelyear.A computerised geological database and modelling system has been implemented to service these mines routinely, as well as several outlying prospects. The database is constantly upgraded for drillhole information, surveyed spot levels on the surface and underground, quality sampling details, surveyed mine workings and geological mapping. This information is edited on a routine basis, allowing dynamic modelling of key aspects of geology for ongoing operations.

Jan 1, 1991

Separating Particles by Horizontal Deflection in a Paramagnetic Fluid This paper describes the horizontal deflection behavior of particles in paramagnetic fluids under a high-gradient superconducting magnetic field. Movements of single particle were observed experimentally and indicated that they could be deflected to different positions. Based on these results, the behavior of groups of particles from ore samples was examined in the superconducting magnetic. It was found that these particles could be deflected and settled at a certain position due to the combination of gravity and magneto-Archimedes forces as well as a lateral buoyancy (displacement) force. Mineral particles with different susceptibilities and/or densities could be deflected to different positions, thus producing groupings of similar types of particles. The work described here, although in its infancy, could form the basis of new approach to separating particles based on a combination of susceptibility and density.  

Sep 13, 2010

Nickel laterite HPAL circuits are known for their complexity and have presented a large number of challenges to process engineers worldwide. An attitude commonly encountered by the author is that the beneficiation of the ore is relatively simple and that the difficult problems are in the realms of hydrometallurgy. On a number of occasions beneficiation has become the 'poor cousin' in the process design phase. Another common theme is that significant difficulties are encountered when beneficiation circuits are started up, invariably slowing the ramp-up of the remainder of the circuit. In some cases the problems impact on throughput for a long period and can require major rectification capital. The HPAL Ni laterite projects encountered each have their own set of beneficiation problems that need to be understood before an appropriate circuit can be designed. This paper will discuss a range of design issues including geometallurgy, ore characterisation through laboratory testing, the application of appropriate sizing and analytical procedures, the selection of appropriate unit operations, materials handling of plant feed and products and setting meaningful plant design requirements.

Jan 1, 2008

By Caress ME, Knight MD

The eruption 75,000 y ago of the Younger Toba Tuff ignimbrite and associated ash-fall ranks as the greatest known volcanic event of the past million years. The ignimbrite is known to cover 21,000 km2 (it may extend farther under alluvium of the coastal plain) and forms a low-angle depositional shield centered on the Lake Toba caldera. The ignimbrite is largely nonwelded and shows systematic outward decreases in lithic and crystal contents and clast sizes. Coarse lithic lag breccias that occur at places 85 km apart point to two or more vents on a fissure having this length. The extensive associated ash-fall traceable as far as Malaysia and India is evidently a co-ignimbrite ash but could have a phreatomag-matic component. The Lake Toba caldera measures95 x 35 km and is >1 kn deep. It is not a single caldera but comprises several contiguous depressions and grabens diversified by two re-surgent domes. Earlier parts of the caldera are related to at least two earlier ignimbrites including the Older Toba Tuff dated by Chesner at 0.5 Ma. The caldera is elongated parallel to, and is only 25 km from, the great Sumatra strike-slip fault, and it can be considered almost certain that the caldera is in part a kind of pull-apart structure. The ignimbrites are very crystal-rich. There is no reason to think basaltic magma was involved in their emplacement. Together with ash-falls they have a total volume of several thousand cubic kilometers. They can be categorized as originating from partially crystallized granitic magmas that erupted because tectonic pull-apart occurred several times across the pluton. Small rhyolitic lava domes on fault-lines comprise the youngest volcanic products.

Jan 1, 1990

The carbon-in-pulp (CIP) process is now well established in the South African gold industry, with a total of over I million metric tons of material being treated each month in six large plants. This tonnage is derived from ground ore, from filtered pulp, from calcine, and from reclaimed sand-tailings dumps. With this new process and the new large plants, those concerned with CIP are experiencing a learning process, since each new plant presents a different set of problems to be overcome. The knowledge and experience gained from these plants is being shared, and will be of benefit in the design and operation of new plants. The CIP process can be subdivided into the following unit operations: prescreening at a fine size, adsorption, acid-washing and elution, reactivation, and electrowinning. Results concerning each of these unit operations, which were obtained from pilot plants and from large-scale CIP plants in South Africa, are presented. The latest developments in each of these areas is summarized. Tables that are included as an appendix contain some information concerning the equipment in these new CIP plants plus operating results from some plants.

Jan 1, 1982

By Weatherstone N

Ironstone outcrops on the Savage River were discovered by State Government Surveyor C. P. Sprent in 1877. The limonitic outcrops were initially regarded as the surface expressions of pos- sible tin-bearing lodes, the tin deposits at Mt. Bischoff to the east having been found in 1871. By the turn of the century, shafts, adits and trenches had been developed on the deposits in the unsuccessful quest for gold, silver and base metals. The deposits were first reported as a possible source of iron ore by Tasmania Department of Mines (TDM) geologists in 1919. Modern exploration began in 1956 with the area registering the best magnetic response during an aeromagnetic survey of North- western Tasmania by the Bureau of Mineral Resources (BMR). The area had previously been reserved by TDM in anticipation of the lifting of the iron ore embargo. Reconnaissance Geologi- cal mapping (TDM) and grid-based magnetometer surveys (BMR) indicated that resources of iron-bearing material could approach hundreds of millions of tons. This provided the incentive for two diamond drill holes funded by TDM which demonstrated iron mineralisation in substantial tonnages, suitable grades and, fol

Jan 1, 1988

By Kesser Z, Vincze T

The Western Mining Corporation mining lease on the Bendigo Goldfield measures 5krri x 18km with more than 20 anticlinal folds parallelling th long north-south boundaries. Numerous closely spaced shafts and extensive underground workings on the reef lines along the folds flooded with groundwater following the progressive abandonment of the field. Preliminary water sampling and assessment demonstrated that a major dewatering programme and acceptable disposal methods were necessary to dewater interconnected old workings in areas of interest prior to any underground work taking place. A field wide geohydolic investigation was undertaken to establish geohydraulic parameters, groundwater recharge rates and water qualities. Data from the field investigation together with estimates of the volume geometry of the submerged workings as obtained from old mine plans, production history, and limited pump testing results were used with an appropriate analytical model to obtain estimates of water discharge rates required to reach various dewatering targets. Water disposal options were limited by relatively high salinities, arsenic levels, contained hydrogen sulphide, and the mine locations within the urban areas surrounding Bendigo. Direct disposal to the surface drainage system could not be considered, treatment to acceptable discharge standards was not economically feasible, and it was necessary to adopt a strategy of collection, containment, and evaporation.

Jan 1, 1988

By H Jones

The paper outlines the adoption and evolution of ‘sustainable development’ as a concept in tailings management practices in the mining industry over the last 30 years. Over 500 lives have been lost in tailings facility accidents since World War 2. The paper outlines commonalities in many of these accidents, particularly the role of excess water. It considers the role effective tailings management can play in enhancing the social acceptability of mining in the future.Tailings management is a major operating cost at many mines while the cost of successfully closing tailings facilities is also very high. Current tailings management practices in the industry are outlined. The technical and engineering challenges of reducing potential risks associated with tailings by reducing water entrainment are described. The successful development of practical techniques to better manage tailings and reduce water consumption and wastage are described. For example, water removal in the alumina industry to produce a paste for dry stacking is now a reality.The future adoption of these new risk reducing techniques by the industry is discussed and the implications of the adoption or non-adoption of these techniques on the industry’s future ‘social licence’ is considered.

Nov 22, 2011

The Barra Mine was the most significant mine of Australia's earliest mining era, which took place in South Australia between 1841 and 1851, the decade prior to discovery of gold in eastern Australia. Between 1845 and 1860, Barra was the largest metalliferous mine in Australia and employed up to 1000 men and boys, most of them Cornish.""Today the site is also important in a physical and archaeological sense as it contains extensive remains of mining and processing operations of the period 1850 - 70. Most significant are three cnginchouses which housed Cornish beam engines.

Jan 1, 1993

By Tonks E. E

The earliest discovery and mining of coal in the northern area of the Greta Coal Measures at Anvil Creek in 1862 was by William Farthing, however, some official records attribute the discovery to Thomas Frost in 1864. Frost's discovery was examined by William Keen, government examiner of coalfields, and further prospecting was carried out. This was followed by the pioneering work of C S Wilkinson, government geologist in 1884. Subsequently in 1886 C S Wilkinson entrusted a detailed survey of the coalfield to the then geological surveyor, T W Edgeworth David.The outcrop of the Greta Coal Measures around the Lochinvar dome was mapped by Edgeworth David and as soon as he reported his discovery, the Department of Mines reserved in the interests of coal mining an area of 23700 acres, which extended between what became the South Greta and Abermain No I Collieries.

Jan 1, 1993

The movements of the major continental cratons and the distribution of the principal tectonostratigraphic terranes are reviewed in the Circum-Pacific region during Phanerozoic time. It is concluded that major periods of orogeny and consolidation of accreted terranes in the Circum-Pacific region is best correlated with periods of advance of cratonic blocks over the Pacific Ocean basin combined with relative convergent to transpressive motions between the cratons and the Pacific Ocean plates. Continental collisions and collision of terranes with continental margins has not been a significant geodynamic process in Circum-Pacific tectonic evolution. The permanency of the Pacific Ocean basin throughout 500 MA is remarkable. It appears no continental block or large continental fragment has ever entered or crossed the Pacific Ocean basin since early Paleozoic time. This area where no continent has entered for 500 MA is almost coincident with the present Pacific Ocean basin and seems associated with the 25 to 100 meter geoid high which dominates the present-day figure of the Earth.

Jan 1, 1990

By Niemann G

The paper addresses certain mining provisions of the Aboriginal Land Rights (Northern Territory) Act 1976 and the development of Mining agreements negotiated pursuant to Section 43 of the Act. Difficulties for miners and Land Councils alike arising out of the operation of the Land Rights Act will be discussed. Possible scenarios for the resolution of these difficulties will be proposed.

Jan 1, 1984

By Szwedzicki T, Jiang J

The acoustic emission (AE) technique has found wide application in rock engineering. Generally, acoustic emission, which is produced by a rapid microcrack growth, is an ubiquitous phenomenon associated with brittle fractures and can provide information on the failure process in rocks. The sudden release of stored energy in the form of an elastic stress wave that travels from the point of origin within the material to a boundary is called an AE signal or a discrete AE event. Based on a number of experiments and analysis, the correlations among the rock type, the complete stress-strain behaviour, mode of failure and AE properties are investigated and the AE pattern has been classified as four types: single-peak AE, double-peak AE, continuous AE and absent AE. Each type of AE pattern corresponds to a certain type of rock and is largely related to the internal structure and imperfection of a rock. Applications of the AE technique in stability monitoring, in situ stress assessment and seismic source location are also discussed.

Jan 1, 1995

The introduction of many new hydraulic ally and pneumatically powered impact breakers over the past few years demonstrates the growing interest in this technique of breaking rocklike material. The most practical method yet devised to increase the blow energy range of hammer type impactors without incurring weight penalities, is to cushion the impact of the hammer on the tool. This has been achieved in one impact breaker by means of replenisible fluid cushions between the tool and the hammer, and blow energies up to 27,000 joule (20,000 ft. lbs.) have been achieved. Impact rock breaking is becoming an important alternative to the use of explosives in the mining and the construction industry. The design of impactors is discussed and manufacturers data is presented for most of the machines now available. A review of the research and mechanics of breaking rocks with impactors is presented and the benefits of high energy impactors are discussed. The relative merits of three impactor design types are explored with regard to achieving high blow energy.

Jan 1, 1978

By Duniam P

Sequencing of large underground firings is a critical aspect of blast performance. Using theory developed in open cut operations, where blast results are easier to quantify, a new technique for sequencing underground mass blasts has been developed. The basis for the technique is to identify timing regimes to control fragmentation and relief then apply non-electrics to fit these criteria. The use of computer software to graphically interpret delay statistics enables the evaluation of designs in a realistic manner.

Jan 1, 1995

By Mostyn G. R

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992