Search Documents

By S Jayakumari, E Ringdalen, V Canaguier

Silicomanganese (SiMn), containing approximately 16–30 per cent Si, is produced in submerged arc furnaces using various Mn sources and quartz as the primary raw materials, along with fluxes and reductants. In the high-temperature zone known as the coke bed, a silica-rich slag is formed. SiMn is produced through the reduction of SiO2 from the slag. Dissolution of quartz into slags with different compositions, the primary slag formed from the Mn sources and flux before any MnO reduction occurred, representing conditions at the top of the coke bed, and dissolution of quartz into a partially reduced slag to simulate conditions inside the coke bed has been investigated. Experimental investigations were carried out to study the dissolution of quartz particles of varying sizes, 5 mm and 25 mm in synthetic slags with different compositions at temperatures between 1400°C and 1600°C, with varying holding times. Observed results are compared with liquidus compositions and equilibrium phases for original and formed slags. Particle size has been shown to be of little importance for the dissolution. Quartz dissolved more easily in slag at top of the coke bed than slag in the coke bed. Complete dissolution was observed after 30 mins at 1600°C in all cases, but not after 0 mins.

Jun 19, 2024

By G King, Q Shu, W Cao, F Gyakwaa, H Singh, S Wang, M Huttula, T Fabritius

Metallurgical slag, such as refining slag, is essential to enhance or promote steel cleanliness. The CaO–MgO–Al2O3–SiO2 system is the primary source of oxides-based inclusions. It plays a vital role in applications in various pyrometallurgical processes. Numerous thermodynamic databases and physicochemical properties of slag studies mainly focus on quenched samples and measurements at room temperature. Consequently, the present study explored the physicochemical, structural properties and crystallisation evolution for CaO–MgO–Al2O3–SiO2 glassy slags via in situ hightemperature Raman spectroscopy and synchrotron X-ray diffraction. The study was carried out by synthesising CaO–MgO–Al2O3–SiO2 slag with varying Al2O3/SiO2 ratios. The results from the in situ high-temperature measurement demonstrated a pattern showing a transformation of a broad peak from the glassy matrix to crystalline peaks. The study showed crystallisation of dominant phases such as Ca2SiO4, Ca2Al2SiO7 and CaAl2O4 that correspond and are attributable to changes of structural units during in situ high-temperature measurements. The results further showed a correlation between an increase and transformation in crystalline phases observed from the spectra obtained from non-isothermal heating of the samples.

Jun 19, 2024

By J Ferreira

To speed up multivariate geostatistical simulation it is common to transform the set of attributes into spatially uncorrelated factors that can be simulated independently. One decorrelation method is the method of minimum/maximum autocorrelation factors (MAF), where a two structure linear model of coregionalisation is assumed. The transformation decorrelates the theoretical model exactly, but the actual data are only approximately decorrelated. The MAF transformation can therefore be seen as a special case of a non-orthogonal approximate diagonaliser of a set of symmetric matrices. A more general approach for approximate joint diagonalisation (AJD) has been developed in the context of blind source separation. For these AJD algorithms no assumptions are made beyond symmetry of the individual matrices and so they can be applied to a family of experimental semivariogram matrices. In their application there are no restrictions on the number of structures in the linear model of coregionalisation (LMC) thus removing one of the conditions placed on the subsequent modelling of the spatial structure of the factors. In this paper the general background for the U-WEDGE AJD method is presented. It is shown that the U-WEDGE method achieves better spatial decorrelation than the MAF method. The factors derived from U-WEDGE are simulated using conditional turning bands simulation and then backtransformed to attribute space.

Sep 26, 2011

By B Besa, E K. Chanda

It has long been recognised that narrow vein mining needs innovative approaches to mine access and mining methods in order to improve the economics of this vital part of the mining industry. The mining equipment used currently requires large openings in narrow vein-type deposits making mining operations uneconomical. In view of this and other shortcomings of the current mining practices, a study was initiated to investigate the potential of using low profile electric loader with mounted conveyor in conjunction with the electric monorail haulage system (EMTS) to load and haul the blasted material, particularly in decline development and main haulages. Computer simulation based on the General Purpose Simulation System/Henrikson (GPSS/H) is used to model the system and evaluate its performance. The results are compared with those for conventional mining using trucks and loaders. The EMTS provides competitive haulage rates in substantially smaller excavations than is currently achievable. According to simulation results, the electric loader in conjunction with the EMTS had the same number of blasts as the conventional system and hence the same advance rate of 3.33 m per 12 hour shift. Furthermore, the total drill-blast-load-haul cycle time was less than the conventional system by one hour.CITATION:Besa, B and Chanda, E K, 2012. Evaluation of low profile electric loader in conjunction with electric monorail haulage system in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 221-228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By R Cox, S Pandey

The coal seam gas (CSG) industry is expanding rapidly in the Surat and Bowen basins. CSG production involves pumping water from the coal seams to release the gas adsorbed to coal particles. The reduction in water pressure in the coal seams will cause some reductions in water pressure in overlying and underlying aquifers because there will always be some interconnectivity between the formations. The Surat Basin is a sub-basin of the Great Artesian Basin, which contains aquifers of high economic, environmental and cultural value. The Condamine Alluvium is also an important water resource, which overlies parts of the eastern margin of the Surat Basin.Under the Queensland (Qld) regulatory framework, an area of intensive CSG development involving multiple CSG operators can be declared to be a cumulative management area. For such areas the Office of Groundwater Impact Assessment develops assessments of future impacts on aquifer water pressures and develops and manages arrangements. The results are published in underground water impact reports.The Surat underground water impact report (QWC, 2012) was approved in December 2012. This paper summarises the place of the report in the Queensland regulatory framework, the content of the report and progress in its implementation.CITATION:Cox, R and Pandey, S, 2013. Managing groundwater impacts in the Surat Basin, in Proceedings Water in Mining 2013 , pp 169-174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

The mining industry is quite often faced with declining selling prices for its products in the face of rising prices for the input cost resources that it uses. Blasting is a key activity within the mining system and has a vital role to play within the Mine to MillTM concept. It is therefore important that blasting makes a positive contribution to mine profit and productivity. There are several variables involved in considering the profitability and productivity of blasting. The rock types and structures, the bench height, the blast hole drill rig specifications, hole diameter, spacing and burden, explosive loading and initiation and blast size fragmentation. Productivity accounting is a methodology which is used elsewhere to give additional insights into the productivity and pricing factors that drive the financial performance of a business. Miners know intuitively that productivity and pricing influence costs and profit, but only with productivity accounting can the dollars involved be calculated. Drilling and blasting are part of a chain of unit operations in a mine. For an owner-miner, drilling and blasting would be considered as cost centres and a productivity accounting cost model approach would be relevant. On the other hand a contractor is likely to consider drilling and blasting as a profit centre, in which case a productivity accounting profit model approach would be appropriate. Both of these will be explained. The paper provides a basic outline of deterministic productivity accounting and demonstrates its application to blasting. Drilling and blasting data from a mine was obtained for a two-month period. The change in productivity and prices was calculated to obtain the dollar contributions from them towards the change in cost. It was determined that although there had been productivity dollar gains these were offset by larger pricing dollar losses, the net effect being that total drilling and blasting costs increased. The productivity accounting analysis gives the facts and the mine is in a position to establish priorities based on knowing the dollar contributions of each input used.

Jan 1, 2001

By R R. Lovel, G J. Sparrow

Currently there are large reserves of good quality iron ore near to existing infrastructure that are not being developed because the phosphorous levels are above acceptable market specifications. Since the high phosphorous content is considered to be mainly associated with the goethite fractions of the ore, attempts were made to leach the phosphorous from the ore after a heat treatment to dehydroxylate the goethite. Heating the ore and leaching with 40 g/L NaOH lowered the phosphorous levels from 0.145 wt per cent P to 0.075 wt per cent P or lower, but a heating temperature over 800¦C was required to achieve this reduction in phosphorous levels. However, when sodium hydroxide was added to the iron ore before the heat treatment, similar phosphorous removal was achieved with a heating temperature of 300 - 350¦C. It was considered that dehydroxylation of the goethite in the presence of the hydroxide makes the phosphorous available for removal with a water leach. As well, 50 per cent of the silica and 60 per cent of the alumina in the ore were also removed in the leach, but some sodium remained in the leach product. Further work is required to remove the residual sodium to produce a marketable product.

Jan 1, 2009

By J Tickner, Y Van Haarlem, G Roach, D Abernethy, M Smith, J OÆDwyer

The development of novel technologies capable of real-time, high-accuracy, automated analysis of gold, other precious metals and mineralogy, both in ore samples and directly on process streams is reported.X-ray fluorescence (XRF) analysis is widely used for process stream monitoring of base metals. However, detection limits are generally a few parts-per-million (ppm) or larger, precluding the use of this method for monitoring precious metals. Complex interferences with other elements also limit accuracy. An XRF slurry analyser that uses advanced data-analysis techniques to resolve overlapping fluorescence lines, achieving detection limits in the parts-per-billion (ppb) range has been developed. This allows feed, concentrate and tailings streams in precious metal applications to be monitored in real-time. An extended trial of our technology in a platinum group element concentrator and laboratory tests on gold process slurries in the 0.1 - 2.0 ppm concentration range is discussed.Analysis of process stream mineralogy can provide useful information to supplement conventional elemental data. An on-stream X-ray diffraction analysis technique that provide real-time mineral and elemental measurement of process slurry streams has been developed. Both X-ray techniques can be combined into a single on-stream analyser to provide simultaneous elemental and mineralogical information. The successful trial of a combined XRDF (X-ray diffraction and fluorescence) slurry analyser is also reported.It is widely recognised that rapid, accurate analysis of grade is an essential prerequisite for optimising the efficiency of exploration, mining and processing of metals ores. The low grades of precious metals ores, such as gold and the platinum group elements, have led to fire assay becoming the predominant analysis technique. Significant drawbacks of fire assay include long turn-around times, limited absolute accuracy, high costs and requirement for skilled operating staff. For rapid measurement of gold samples, a technique that allows the gold content of large samples to be determined absolutely with high accuracy in less than two minutes using activation with high-energy X-rays has been developed. The method is non-destructive, has detection limits in the low ppb range, is capable of measuring slurries, ground or crushed solids with minimal preparation and can be made fully automatic. Initial results from laboratory trials are presented.CITATION:Roach, G, Abernethy, D, OÆDwyer, J, Smith, M, Tickner, J and Van Haarlem, Y, 2013. Advanced instrumentation for analysis of exploration, mining and process materials, in Proceedings World Gold 2013 , pp 277-282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

This paper investigates the adequacy of current gas monitoring techniques to adequately detect spontaneous combustion in underground coalmines. Despite being in the 21st century spontaneous combustion continues to occur in underground coalmines sometimes being detected only at a very advanced stage. Control of the incident is often then very expensive and time consuming. The adequacy needs to be assessed not only from the point of view of the analysis technique be it tube bundle, gas chromatograph or real time sensor but also the number, location and sampling frequency of the monitoring locations. Recommendations are made to optimise monitoring processes and recognise limitations of current techniques.

Jan 1, 2005

By J Rostami, T Afshar, M Sharifzadeh

Accurate estimation of rock load and selection of types of ground reinforcement to match post-failure behaviour of rock mass are important issues to assure tunnel stability. This paper focuses on the main factors affecting rock load to evaluate the capabilities of the existing models for prediction of rock load. Rock mass properties, project features and excavation method, as well as ground conditions and stress condition were found to be the key factors affecting the magnitude of rock load. Field data from tunnels of about 37.5?km driven in several geological structures in non-squeezing ground was used in this study. An in depth statistical analysis was performed on data to find correlations between the input parameters and measured/observed rock load. A weighting system was proposed to obtain the proper contribution of each factor for estimation of rock load in tunnelling through various ground conditions. The new classification system offered predicted values for rock load that were in a good agreement with the actual field measurements. The high disturbance factor (D>0.4) was the prime factor which controlled the rock load. Rock mass quality was the second key factor influencing rock load, which could be estimated by GSI, GSIresidual , especially when combined with tunnel depth.CITATION:Afshar, T, Sharifzadeh, M and Rostami, J, 2014. Estimation of rock load for tunnels with different disturbance factors, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Woodley, N C. Kunz

A mine site water balance is important for communicating information to interested stakeholders, for reporting on water performance and for anticipating and mitigating water-related risks through water use/demand forecasting. Gaining accuracy over the water balance is therefore crucial for sites to achieve best practice water management and to maintain their social license to operate. For sites that are located in high rainfall environments the water received to storage dams through run-off can represent a large proportion of the overall inputs to site; inaccuracies in these flows can therefore lead to inaccuracies in the overall site water balance.Hydrological models that estimate run-off flows are often incorporated into simulation models used for water use/demand forecasting. The Australian Water Balance Model (AWBM) is one example that has been widely applied in the Australian context. However, the calibration of AWBM in a mining context can be challenging. Through a detailed case study, we outline an approach that was used to calibrate and validate AWBM at a mine site. Commencing with a data set of monitored dam levels, a mass balance approach was used to generate an observed run-off sequence. By incorporating a portion of this observed data set into the calibration routine, we achieved a closer fit between the observed versus simulated data set compared with the base case. We conclude by highlighting opportunities for future research to improve the calibration fit through improving the quality of the input data set. This will ultimately lead to better models for run-off prediction and thereby improve the accuracy of mine site water balances.CITATION:Kunz, N C and Woodley, A, 2013. Improving the accuracy of mine site water balances through improved estimation of run-off volumes, in Proceedings Water in Mining 2013 , pp 267-272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Y Cao, J C. Tien

Occupational health and safety is essential in modern mining workplaces and in China it is often not given enough emphasis due to a lack of knowledge and/or appreciation. Although many health and safety regulations have been passed over the years, serious and relevant laws and regulations on mine health and safety are of recent history (since 2002), the level of stringent enforcement is still inconsistent and accurate field data are scant and not readily available. As of year-end 2006 there were 676 562 recorded cases of occupational diseases in China, of which 616 442 or 91 per cent were miners’ pneumoconiosis. Of these, 146 195 (23 per cent) have died, and an average of 10 000 new cases were added every year between 1991 and 2006. Another report shows that 93.18 per cent of miners have never had a contract with their companies, which means their cases were not even part of China’s official statistics. This study attempts to examine the prevalence of occupational diseases in the Chinese mining industry during 2000–2013, compiled from government annual reports and academic studies. The research will review the correlational analysis among occupational diseases, ventilation practices, protection devices and legislation.CITATION:Cao, Y and Tien, J C, 2015. Occupational diseases in China, with the emphasis on its occurrence in Chinese mine workers, in Proceedings The Australian Mine Ventilation Conference, pp 155–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By C Li

Removal of gangue minerals from ilmenite concentrates can be accomplished by relatively low temperature roasting in controlled gas atmospheres to selectively enhance the magnetic separation characteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphere roasts were characterised by combining elemental analyses with quantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

By Rashleigh C

The selection and application of an effect- ive firing system first require a clear under- standing of the initiating abilities of the com- ponents in such systems. The conditions under which charges can be prematurely initiated by a detonating cord downline must be appreciated. This is a principal consideration in the design of a successful downline/'Anodet'/primer assembly. The advantages and limitations of an electric and several non-electric initiating systems are explained. The factors which in- fluenced selection of the two most suitable systems for use at Isa Mine (viz. downline/ 'Anodet'/primer assemblies and the reinforced long-lead 'Anodet'-type delay system) are dis- cussed. Blasts are detailed in which each of these has been applied. The initiating design for a hypothetical 2 x 106 tonne blast using electric short delay detonators and multi-channel exploders is presented. In this design, charges in remote blastholes are activated after the detonation of earlier firing charges by protecting the firing lines with sandbags.

Jan 1, 1978

By Snowden D. V, Standing C. A, Ryba A, Bywater A

McKinnons open pit gold mine, located within the Cobar Basin in New South Wales, is characterised by complex mineralisation controlled by the intersection of steep faults in the hinge zone of an anticline. Resource estimation using indicator variography and indicator kriging was based on RC drilling on 25 in sections together with grade control RC drilling on 12 in by 12 in and 6 m by 6 in patterns. Rigorous sampling and checking procedures were used to verify the reliability of the drill hole data. Blast hole data was used to assist grade control in defining ore block boundaries.

Jan 1, 1997

By G J JAMESON

The flotation cell has undergone a number of changes since the process was first introduced in Broken Hill in the early years of this century. The development of the mechanical flotation cell is reviewed, followed by a discussion of more recent developments such as the flotation column, the air-sparged hydrocyclone, the Wemco-Leeds cell, the Bahr and Deister columns and the Jameson cell.

Jan 1, 1992

In November 1986 the Australian Minerals and Energy Council (AMEC) endorsed an "Australian Code for Reporting Identified Coal Resources and Reserves" for use by the Federal and all State Governments. Before this endorsement there were six different coal codes in use in Australia. The code is broad in nature to accommodate the wide range of coal deposits in terms of rank, quality and geological environment, that are present in Australia. In the code, Resources refer to all of the coal in situ which may have potential for use and the various categories indicate the level of confidence of the assessment. Reserves are those Resources which are planned to be mined and for which such planning has been undertaken. Only minimum guidelines are set by the code and the onus is on the estimator to state clearly the criteria used in any Assessment.

Jan 1, 1987

Vertical flow systems (SAPS, vertical flow wetlands) are increasingly used for passive treatment of mine drainage that is net acid. Data on 30 systems in eastern US show that well designed systems typically add about 40 g/d/m2 of alkalinity to influent net acid water. If they are designed with a conservative loading rate of 25 g/d/m2 and carefully constructed, they produce net alkaline water. Alkalinity added depends on influent acidity, Fe, pH, and retention time, and ranges widely, from 7 to 484 mg/L, so this is not a useful design criterion. Some waters may benefit from retention times longer than the conventional 12 - 16 hours, but the design must be partly based on cost-benefit considerations. Systems with fine limestone added to the compost layer perform better than average, perhaps to an alkalinity generation rate of 80 g/m2/d. A variety of problems are noted in the 30 systems and others reported in the literature. Systems with high influent Fe (> ~75 mg/L, varying with pH) tend to gradually decrease in flow rate because of precipitation and settling of Fe hydroxides on top of the compost layer. Some high-Fe systems precipitate Fe in the limestone layer, suggesting inadequate compost thickness, or short-circuiting through thin spots. Systems with Al exceeding about 10 mg/L tend to plug because of Al hydroxide precipitation in the limestone layer. Flushing only removes a small part of this precipitate, but can extend life. Some systems are ineffective because of failure of the inflow system. Some systems are uneconomic because they are oversized. A continuing program of inspection and maintenance is necessary for long-term performance.

Jan 1, 2003

By C Preston, T Williams, D Roy

The easiest way to mine valuable orebodies is through the use of explosives and well-planned blasting layouts that produce fragmentation profiles designed specifically for conveyance equipment in underground mines. The design of blasting patterns is specific to not only the explosives being used but also the rock or ore type being fragmented. Many blasting designs are based solely on the experience of those developed for similar orebodies in terms of properties and orientation or individuals that have some blasting experience.The primary technical objective of this paper is to outline a unique methodology for determining underground blasting methodologies (developing specific blasting parameters) commensurate with explosive energies and rock/ore equations of state for a narrow-vein gold property located in Northern Quebec and for underground mines in general.The procedures developed are to define the desired fragmentation specification so that a specific thermodynamic break is generated, taking into account powder factor, energy factor, tonnages, explosive energies and distribution along with blasthole diameter and orebody orientation for a specific set of explosive and dynamic rock/ore properties. Determining dynamic modulus values for the ore using seismic sensors to measure P- and S-wave velocities, the aforementioned parameters will be utilised to set the design constraints to maximise recovery and minimise overbreak and dilution.New underground blasting software (AEGIS) will use thermodynamic break in conjunction with defined fragmentation profiles to create an array of blasting parameters used to design and plan ring layouts. This software will also allow mining planners, prior to drilling and loading a production blast, to appraise future intended blasting patterns to minimise the potential of diluting ore with host rock and the likelihood of damaging mine support structures.CITATION:Roy, D, Williams, T and Preston, C, 2015. Underground stope drill and blast designs optimisation program, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 137–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S Brochot

During the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material coming from a selection of various drilling products or a sample coming from a mining test. This sample can represent several tonnes of material which are analysed and split to be used in various tests.In the current case, a composite sample is dedicated to semi-autogenous grinding (SAG) pilot plant tests. The property of interest is then the size distribution of the material. The sample is mixed and a subsample is taken to measure the size distribution which is considered as the feed size distribution. Then the remaining material of the sample is divided in several subsamples for batch grinding tests at different operating conditions. The product of each grinding test is then analysed to measure its size distribution.The grinding performances are analysed at the light of the measured size distributions for feed and product. But what is the accuracy of the measurement of these size distributions? What is the variability of the feed knowing each feed is just a subsample of the initial sample?The Pierre Gy theory of sampling answers these questions.The current paper presents, through a real example, the calculation of the measurement error of the size distributions and the variability of the feed between the different tests. The uncertainties of the grinding performances are then calculated and their impact on the results interpretation is then analysed.CITATION:Brochot, S, 2012. Sampling for grinding pilot plant test - the effect of size distribution variability, in Proceedings Sampling 2012 , pp 127-134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012