Search Documents

The Lihir deposit in Papua New Guinea (PNG) contains an estimated mineable reserve of 454t (14.6M oz) of gold in refractory sulphide ore. The Lihir Joint Venture has submitted a proposal to the PNG Government to develop an open pit mine and to install a process plant and associated infrastructure facilities on Lihir Island. The proposed process plant will employ whole-ore pressure oxidation technology, has a design capacity of 2.825Mt/a of ore containing 7.20 sulphide sulphur, and is expected to average 19.3t/a (620,000 oz/a) in gold production during its first 12 years of operation.An extensive program of process development testwork and feasibility engineering was completed to establish the process plant design for the Lihir Project. Summary results of this test-work as well as key design criteria, the process flowsheet, and major equipment selected for the commercial plant are presented and discussed.

Jan 1, 1994

By Hargraves AJ

Pre-drainage experiments have been conduct- ed at Appin, Cook, John Darling, Leichhardt, Macquarie, Metropolitan and Moura No. 2 Collieries. Appin (550 m deep) experiences particular gas problems in development drivages, and the almost pure CH4 seam gas makes difficult tiro compliance with statutory maxima in intakes and returns. Patterns of 43 mm diameter drain- a,.;e holes drilled ahead and laterally into virgin coal have improved gas conditions in working places and have allowed tolerable advance rates. Cook, Leichhardt, Metropolitan and Moura No,. 2 Collieries have experienced gas and stress phenomena ranging from conical bursts less than one tonne to full scale instantan- -us outbursts of hundreds of tonnes with tens ,f thousands of cubic metres of seam gas. Gas ~Irainage experiments with patterns of holes up a,, 200 mm diameter have been undertaken with ;,;siness monitors on the coal to establish .lative effectiveness. Incremental flows into mg 43 mm diameter boreholes have investigated drainage patterns relative to length, and at comparative incremental flows have nlicated lowered permeability zones at stress ,.,utments. In some CO2 seam gas areas where iammability problems are reduced to perhaps ii, but where outbursts proneness is increased,

Jan 1, 1982

For an exploration area with a predetermined grid of data points, a construction is given for elementary blocks which subdivide the entire area without omission or overlap, and with the property that each data point is situated at the centre of its corresponding block. The construction has a useful optimal property, and more importantly avoids an error which has been made recently in more than one publication.

Jan 1, 1985

By E Acu±a, B Prosser, R Alvarez, K Wallace

This paper describes the ventilation analyses performed for the access tunnels at the New Level Mine project (NLMP) at CodelcoÆs El Teniente operation outside of Rancagua, Chile. This new mine is anticipated to reach a final production of between 137 and 180 kt/d. Production from the NLMP is scheduled to start in the year 2017. The main access tunnels (MAT) are approximately 9 km in length, with one for personnel and supply access and the second one for ore extraction through a conveyor system. These two tunnels are a critical component of the initial stage 1 development and will be constructed independently of the existing mine workings. The tunnels were originally designed to be constructed with two tunnel boring machines. However, later analyses changed the construction approach to a conventional drill and blast technique. Because the design included two mid-tunnel ramp-to-surface connections, conventional mining methods would allow for development of the tunnels with multiple working faces to achieve a more rapid schedule. This paper presents the initial baseline considered for the ventilation design and the optimisation methodology applied by Codelco to minimise the airflow and pressure requirements of the ventilation system. Modifications to the design resulted in the addition of strategic airways and raises that could provide a saving of approximately 1 MW, when compared to the original design.CITATION:Acu±a, E, Alvarez, R, Wallace, K and Prosser, B, 2013. Ventilation considerations for the new level mine project access tunnels, in Proceedings The Australian Mine Ventilation Conference , pp 203-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

Commercial or potentially commercial deposits of coal occur in Australia in strata ranging in age from Permian to Tertiary. The coals of each period tend to show a community of petrographic character and significant differences as compared with coals of other ages. In particular- many of the Permian coals are unusually rich in inertinite whereas the Jurassic and Tertiary coals are typically very rich in vitrinite. The majority of the coals show evidence of deposition in environments subject to relatively minor marine influence. Except for some Tertiary and Permian coals the content of mineral matter tends to be high. Outcrops of coals of bituminous rank appear to be largely restricted to the eastern margin of the Australian continent. In this region vertical rank gradients are generally higher than in the other sedimentary basins and uplift and the removal of cover has occurred to a greater extent. To the west of the Tasman geosyncline, coal of bituminous rank generally occurs at considerable depths (usually in excess of 1 km and in some areas only at depths of over 2 kms), and in most areas coals at shallow depth are of sub-bituminous or brown coal rank. The controls of the distribution of coal type and rank have considerable economic significance and the unusual characteristics of Australian coals, especially with respect to coal type, make the direct application of overseas technology to Australian coals inappropriate.

Jan 1, 1975

By LaBrooy SR

A number of gold processing plants in Western Australia have nickel in their ores, leading to significant levels of nickel on their loaded carbon. The presence of nickel during leaching, adsorption and elution'may have detrimental effects on cyanide consumption, carbon inventory requirements, stripping costs, electrowinning efficiencies and may contaminate the gold bullion.This paper discusses the competitive adsorption of gold and nickel cyanides onto activated carbon and investigates changes in solution parameters that may improve gold adsorption and/or inhibit nickel adsorotion.

Jan 1, 1997

By B Olsson, C Glassock

Computer simulation modelling (discrete event) has been used at Olympic Dam (OD) to model the handling of ore from the point of extraction at the stope drawpoint through to the ore stockpile on the surface. Computer simulation is a well accepted tool for modelling the behaviour of such large and complex operating systems. It is a particularly useful technique in complex operations where there are multiple interactions between the inputs and outputs of various unit operations. In this instance it can be utilised during the early stages of a project, for example, as part of the business case definition phase or the early engineering phase. A well constructed and tested simulation model provides a sound base upon which informed business decisions can be made. Furthermore, the behaviour of the model with varying inputs can help build a solid understanding of how the asset behaves when varying inputs and constraints are imposed upon it and, as a result, the major points of leverage that designers and operations personnel have to affect the real world behaviour of those assets. Better decisions can be made when the right facts can be examined, various options explored and conclusions tested. Simulation modelling is one of the tools available to make this process work.

Jan 1, 2005

By Bernard G, Limpach R, Ulveling L

A major aspect in competitive ironmaking is to replace metallurgical coke by injecting alternative cheap fuels. Whereas in the past, heavy oil injection as well as on a lower scale natural gas injection have proved to be reliable, the progressing high price level of these fuels has prompted international interest in looking for alternative cheaper fuels, especially pulverized coal. Theoretical analysis and practical operations showed that for constant adiabatic flame temperature, potentially more coke may be replaced by injected coal than by heavy oil, because of less endothermic cracking of hydrogen components. Since about 1974, the ARBED-Group has been looking for alternative fuels and in 1976 came to conclusion to select for first trials pulverized lignite for the following reasons:

Jan 1, 1981

The paper focuses on how rock bolts are loaded in different rock masses, as well as in pullout tests. Three analytical models for rock bolts are presented in brief, one for bolts in continuously deformed rock masses, one for bolts in blocky rock masses, and one for bolts in pullout tests. The bolt models are used to interpret measurement data for rock bolts from three sources and to help specify the modes of axial load in the rock bolts. It is found that in continuously deformed rock formations fully coupled rock bolts have only one axial stress peak. The position of the axial stress peak moves towards the far end of the bolts with increasing rock deformation. In blocky rock masses several axial stress peaks may appear in the rock bolt. The position of this kind of axial stress peak does not change during the entire loading process. For rock bolts in pullout tests, decoupling of the interface always occurs first at the loading point. The decoupling front moves towards the far end of the bolt with an increase in the applied pull load.

Jan 1, 2000

Coal slurry pumping was introduced into the U.K. in 1973. Gateside packs were prepared in areas of containment using R.O.M. coal and a special fast setting cement. The packs restricted roadway convergence and moderated spontaneous combustion risks, but costs were high and alternptives were sought. A similar system using OPC and an accelerator had limited success. Much more successful was the Aquapack process which used dilute slurries of a special OPC based cement and an accelerator based on sodium carbonate and bentonite pumped simultaneously into la fabric packbag. The Tekpak system using HAC and a much modified calcium sulphate mixture superceded Aquapack on the grounds of improved cement pumping life lower alkalinity and lower costs. A further modification of this system gave a cement with a 24 hour pumping life thus obviating flushing out pipe ranges except at the week-ends, improved packbags also increased the efficiency of the process. The hazard of spontaneous combustion can be inhibited if air supply channels across the waste can be located and plugged. Using gas samples from pack pipes to locate the heating and injecting a special grout, formulated from bentonite, sodium silicate and thixotroping agents. into the waste on the intake road has proved a successful method of controlling heatings. Mine' roadway and face cavities are being safely and successfully filled with cementitious foams produced in a novel placer machine. The foams are based on fast setting cements with specialised foaming agents. Up to 13 cu. metres per hour of fast setting thixotropic foams can be produced and their use is now widespread throughout U.K. coal mines.

Jan 1, 1986

By Montini A

The dynamic behaviour of the load in a pilot-scale ball mill has been measured as a function of axial position within the mill, end plate lifter design, load volume J (percent of mill volume), percent solids in the slurry S and mill speed N (percent of critical speed). Conductivity probes were inserted through the shell of the mill to provide online measurements of the dynamic orientation of the load in the mill. It was found that 1. the height of the shoulder of the load is increased by increasing J, S or N. 2. Measurements of the effect of S on the location of the shoulder of the load should be very useful in mill control strategies. 3. The axial centre of gravity of the load in the mill is not affected by operating conditions. 4. The presence of lifters on the feed end plate does not affect the torque drawn by the mill. 5. Holdup of slurry in the mill is a strong function of slurry viscosity and a weak function of mill speed.

Jan 1, 1986

By Morland R

In the course of an exploration program aimed at increasing Pasminco Mining's ore reserves, an electromagnetic survey down one of the underground drillholes at the North Mine, Broken Hill, recorded a broad and persistent response. This paper demonstrates that the anomaly was not due to any geological feature, but rather was caused by 'self-response' of the sensing probe. The observed results are due to the surveyed hole lying within a resistive environment and having distinct, but not unusual, changes in dip.This phenomenon has not been widely reported and we believe that there are likely to be similar cases in company records where very genuine looking responses are due to self-response rather than sulphides. These false anomalies can be recognised by correlating the observed data with the calculated down-hole component of the transmitting loop's primary field.

Jan 1, 1994

By Diessel C. F K, Ng N

The commonly used Stopes-Heerlen coal petrographic classification and nomenclature has over the years been subject to variable interpretations. This paper discusses the problem with specific reference to the inertinite maceral group. The effect of various interpretations of the Stopes-Heerlen system on maceral analysis is discussed and illustrated by means of comparative analyses conducted by a number of laboratories in Australia. An attempt is made to define the reflectance thresholds used by the authors to subdivide the inertinite group; the genetic and technological significance of these thresholds are compared. The difficulties of distinguishing structured and non-structured macerals of the inertinite group is discussed in terms of possible improvements to the present Stopes-Heerlen system by extending the classification to include transitional maceral types.

Jan 1, 1969

Studying the ore textures in a discrete orebody is a novel approach to estimating liberation potential of the ore minerals present. As part of a PhD thesis, this project aims at classifying and quantifying the textures of the Hilton North orebodies, and at estimating their liberation characteristics.

Jan 1, 1993

By Valenta R. K

A technique is presented for the integrated forward modelling of the three-dimensional structure and the geophysical response of multiply deformed terrains. This technique allows information collected by field geologists and geophysicist to be reconciled by the development of a simplified kinematic structural history of the area. The structural modelling simulates the deformation history of the area in terms of a succession of structural events, such as folds, shear zones and intrusions. The interaction of these events with a starting stratigraphy results in the prediction of the geometry of the structures. By specifying geophysical rock properties for the units in the initial stratigraphy predictions are possible for the potential field anomalies for gravity and magnetics. This approach is suited to a range of applications, and its uses in the modelling of regional structures, testing of geophysical data processing, volume balancing, multiply constrained inversion and training are discussed.

Jan 1, 1995

Laboratory experiments have been used tostudy a wide range of convective processes which are significant for the formation of rocks and the ores that form in them. Metal-rich solutions flowing through the sea floor produce 'black smoker' chimneys; both the size and structure of a solid chimney and the height to which the plume of effluent rises above it can be predicted using model experiments. Analogues of processes in solidifying magmas can also be studied using crystallizing aqueous solutions. The release of lighter or denser residual fluid as crystallization proceeds, and the resulting compositional convection, have a vital influence on the differentiation of initially homogeneous magma and on the evolution of stratified magma chambers. Mixing during the replenishment of magma chambers, and its dependence on the rate of filling and on the fluid properties, have also been studied on the laboratory scale. Experiments carried out in different geometries have been applied here to the formation of platinum and chromite ores and komatiite lavas. Larger-scale mantle convection, in particular the motion of subducting plates and plumes rising from the core-mantle boundary, also determine the tectonic settings in which ore bodies form. These phenomena too can be usefully investigated in laboratory experiments using very viscous fluids.

Jan 1, 1990

The Favona Underground Project is located approximately two kilometres east of Martha Mine Open Pit in Waihi, 150 km south east of Auckland, New Zealand.   The underground reserve of 354 koz Au contained in resources of almost 600 koz lies within 600 m of the existing process plant presenting an attractive development target in a challenging environment.   The Martha Mine Open Pit is surrounded by urban housing on the north western edge of Waihi township and the Favona Underground abuts residences on the eastern edge of town. Environmental, community and social licence aspects influence project strategies as the new underground mine extends mining in a town that is planning for closure of current open pit operations in late 2006.   The Favona Underground Project has successfully passed through a detailed feasibility study, the third stage of the five stage Newmont project appraisal system. Methodologies used in the feasibility study and parallel permitting draw on a high level of stakeholder involvement to streamline the development and permitting phases.   This paper discusses the project appraisal process and design innovation required for developing an underground mine adjacent to town.

Jan 1, 2004

The development of present methods of pillar extraction has evolved from the very earliest of hand mining operations which were limited in scope by venti- lation and transport considerations. Conservation and safety considerations also have led to the current shortwall operations with conventional equipment and powered supports. The shortwall methods have had significant effects on safety, costs, con- servation, flexibility, and other aspects of pillar extraction. The present stage falls short of the ideal but is some guide to prediction in what direction may lie the ideal methods for the future.

Jan 1, 1974

By S C. Dominy

The Bendigo Goldfield is located in the state of Victoria, Australia, and is one of a number of quartz-reef fields that make up the greater Central Victorian Goldfield. At Bendigo gold particles are characterised by their very coarse nature, ranging from below 100 to over 10 000 ¦m in size. Some 60 per cent of the gold occurs in particles greater than 1000 ¦m in size. This characteristic ensures that the mineralisation is very challenging to both sample and evaluate. Diamond drilling provides a measure of geological structure, but is a poor measure of in situ grade, understating it by up to 75 per cent. Drilling combined with on-reef development, bulk sampling and geological interpretation has been used to define Indicated Mineral Resources. For grade control, a balance had to be sought between sample representivity, cost, turn around time and practicality. Sampling of extreme nugget effect deposits generally requires the use of bulk sampling in order to be representative. However, the cost and turn around time is significant. As a result, a 50 kg micro-bulk sampling system has been introduced that attempts to overcome these problems by providing a fast, practical method that can discriminate between ore and waste. As the mine passes into production, grade control will increasingly become dependent upon geological data collection and interpretation.

Jan 1, 2005

I The South Platform of the Gippsland Basin is an extensive area of shallow basement covered by a relatively-thin Late Mesozoic-Cainozoic section. Although the sporadic exploration to-date has not resulted in any hydrocarbon discoveries, the area is under-explored and its taste potential has not yet been fully evaluated. The best potential appears to be in areas underlain by the Golden Beach Megasequence where structures are mainly related to basement fault blocks.

Jan 1, 1992