Search Documents

By R Varden

Friction rock stabilisers, commonly termed ‘Split Sets’, friction rock bolts, or continuous friction coupled bolts are the most widely used rock bolt in the Australian underground metalliferous industry. Historically, they were used for temporary reinforcement, mainly within ore development. However, their use as primary reinforcement has grown with the demand for higher development rates at lower costs. The introduction of galvanisation has increased their longevity and pattern bolting in conjunction with weld mesh, specifically made for use in development headings, has allowed the use of friction rock stabilisers to increase rapidly with development jumbo’s undertaking the installation. The installation of friction rock stabilisers appears to be deceptively simple, particularly when compared to resin encapsulated bolts. The friction rock stabilisers capacity is a function of the borehole parameters, rock mass quality/strength, the bolt dimensions and steel quality, and lastly and perhaps the most important the operator skill levels. However, as in industry we are still seeing common occurrences of friction rock stabilisers not reaching their design pull test capacity. Pull testing the friction rock stabilisers is used to verify the installation of the design capacity. It involves loading the collar of the bolt with a hydraulic ram until the design load is reached or the bolt slips. Pull tests often show failure rates of 20 per cent or higher. This is despite over 40 years of use and with millions of units installed annually. Such high failure rates would suggest there remain issues with the quality of installation. Ground support quality assurance and quality control (QAQC) programs are needed in combination with operator training to ensure that pull test failure rates are kept as low as practical. However, there are times when despite the QAQC being completed the pull test failure rates increase quite suddenly. When this occurs, it is important to conduct a thorough investigation. These investigations often show there are several factors that are not obvious to personnel installing the bolts. To complete a useful investigation, it must also be done methodically, working through the entire process that includes less obvious factors such as steel quality and the calibration of the hydraulic pull test kit. The aim of the paper is to give mine practitioners an understanding of the complexities of friction rock stabilisers, what QAQC requirements they should be doing on-site, what can go wrong during installation and, if necessary, a process of how to conduct investigations into high friction rock stabiliser pull test failure rates.

Mar 29, 2023

Morning Star Gold aims to enter the ranks of Australia's gold producers, revitalising the Eastern Victorian Goldfi elds in the second half of 2010 - the fi rst gold production in around 50 years from the Morning Star Gold mine, which was once Australia's largest under WMC. This presentation will outline the redevelopment of the Morning Star Gold Mine from exploration to production. Morning Star Gold NL's (MCO) key project area is centred at the historic mining town of Woods Point and nearby Matlock (to the southeast) and Gaffney's Creek (to the northwest), all of which are located in the lower part of the Victorian Alps roughly 60 kms south of Mansfield. Morning Star has literally numerous historic mines and gold bearing 'dykes' on its tenements, many with a rich production history of high-grade gold from quartz reefs and alluvial sources. The area encompassing the Woods Point goldfi eld and the multiple high-grade gold bearing dyke structures located north towards Jamieson and south towards Walhalla formed one of the most significant mining fields in Australian history. Historical gold production was at least 155 t or around six million ounces of over a century of mining with an average production grade exceeding 27 g per tonne. The bulk of this recorded production came from just a handful of mines and of those only three were mined to any great depth. One of the key historical production hubs in this area was the famous 'Morning Star' mine, which is situated adjacent to Woods Point township. The Morning Star mine produced almost one million ounces at 27 grams per tonne, operating fairly continuously between 1861 and 1959 with a break after Jan 1939 due to the devastating 'Black Friday' bush fi res across eastern Victoria. During the early 1940s, the Morning Star was Australia's biggest gold mine. The Morning Star mine along with Walhalla ensured that this goldfield was third behind Bendigo and Ballarat as Victoria's biggest hardrock gold production centre. Morning Star Gold has rebuilt its 100 per cent owned 'Morning Star' mine with a view to producing gold in the second half of 2010. Morning Star is exploring its regional dykes in order to estimate an overall gold endowment and rank local production sources to feed its proposed mill at the Morning Star mine site. Key initial targets (all within 11 kms of the Morning Star mine) are the Waverly, All Nations, Rose of Denmark, Hunts, Wallaby and Loch Fyne dykes, all of which historically produced high grade gold, much of it gained from only shallow workings above the water table in the weathered zone of rocks. Historically the Morning Star mine was developed over 24 levels to a depth of 940 m via one large vertical shaft and a smaller, deeper inclined shaft at the 1900 feet level underground. At present MCO has dewatered and completely refurbished all infrastructure to the ten level (~310 m below surface). MCO knows there are a number of substantially under-explored and undeveloped or partially developed but not stoped areas within the Morning Star mine. As a result, MCO has been carrying out extensive channel sampling and an underground diamond drilling program targeting areas of the mine that were largely unexplored and undeveloped by the last operators of the mine - Western Mining Corp Ltd (Gold Mines of Australia). Four thousand, fi ve hundred pages of archival WMC records have helped the cause significantly. The shaft refurbishment and reconstruction stage is complete. This has been a program that originally commenced back in 1993 and has cost around $22 M. This refurbishment paved the way for the extensive underground resource focused diamond drilling program, which MCO completed in 2008 with two company-owned and operated drill rigs from drill cuddies on level 9 (900 feet underground) of the mine. This drilling, which encountered some stunning grades intersections and multiple visible gold hits, has outlined further production opportunities including 0.4 m @ 1392 g/t Au (MS 410). Metallurgical testing conducted by Gekko Systems of samples obtained from the exploration program found gravity concentration and a leach circuit gave recoveries of ~95 per cent to 99 per cent, or ~92 per cent from gravity alone at a coarse crush (300 ¦m). Currently, the plan is to use gravity to fi rstly produce dore bars on-site from the free milling gold and secondly a saleable concentrate for CIL processing off-site. A purpose built 10 t/h (~80 000 t/a) gravity treatment plant was subsequently ordered from Gekko and is expected to be installed onsite and commissioned in the Q3 2010. The plant features fi ne crushing with a vertical shaft impactor, followed by gold concentration by inline pressure jig, inline spinner and Wilfley table. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Aug 1, 2010

By A Bennett, S Arndt

Minerals and Metals Group Pty Ltd (Golden Grove Mine) commissioned a comprehensive study of the life of mine using advanced 3D stress modelling. Essential input into the modelling was the proposed mining sequence, itself the culmination of years of planning and geotechnical experience gained in comparing actual performance to predictions. The modelling approach addressed the whole of mine at a scale of 5 km. There were however several magnitudes of scale to address, from the scale of laboratory testing (0.05 m), to drive size (5 m), extraction size (50 m) and stope size (500 m). Scaling was therefore an integral part of the procedure. The constitutive rock properties in terms of peak and post-peak behaviour varied with the scale. At the laboratory scale, the constitutive relationships for all the main rock units were determined in 3D as well as recovering the in situ stress using the rock memory technique, deformation rate analysis (DRA), whereas at the larger scale the properties were varied to match observations.The modelling, using non-linear analysis to account for rock mass yield and peak-residual strength, demonstrated that if the planned extraction sequence and stope geometry had been pursued there was a high probability of large volumes of excess shear stress being released. However, it was not possible to identify whether the excess shear stress (ESS) will release as one large event or many smaller events. The mining approach was to modify the extraction sequence/stope geometry to manage the hazard. This is where the economic advantage can be realised.Alternatively or in combination with further modelling, the volume identified with the predicted high ESS or energy release could be intensively explored for structures having adverse orientation to the stress change and with sufficient areal extent to release the ESS. The microseismic data can be interrogated for the likelihood of a large event to support the hypothesis of a singular release versus multiple releases of smaller events. If the initial planned extraction sequence had to proceed as designed, changes to dimensioned stopes would be recommended for risk mitigation. Mine planning could as an option, modify the sequence and the extraction could then be remodelled.CITATION:Bennett, A, Arndt, S and Dight, P M, 2014. The economic advantages of detailed geotechnical assessments for extraction sequencing, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 243–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Y Xu, T Rowles, B Dareeju, A Dissanayake

Recent updates on tailings dam design guidelines require analysis of undrained (short-term) stability with the application of the SHANSEP model. The SHANSEP model, which was originally developed for alluvial soils, predicates that the Undrained Shear Strength (Su) increases with increasing effective stress. Residual soils by their nature do not necessarily follow this relationship. This paper examines an alternate method to define Su over a range of effective stress conditions for residual soils. Residual soils, formed by weathering of their parent rocks, are generally micro-structured in nature. The microstructural features, such as interparticle bonding, play a fundamental role in stress-strain behaviour of the residual soils. As interparticle bonding is independent of effective stress and void ratio, the undrained shear strength of residual soils is expected to be less dependent on effective stress than alluvial soils, especially at low stress levels. A series of triaxial tests conducted on residual soils, however, indicated that the undrained shear strength and the undrained shear strength ratio (Su/σv’) are to a degree dependant on effective stress. It was found that the undrained shear strength ratio is significantly higher under low stress levels and progressively reduces with increasing effective stress. Based on the laboratory testing data, a strength function with varying undrained shear strength ratios can be developed for the residual soils under the stress range anticipated for a design of a tailings dam. This includes capping the input undrained strength at lower effective stresses based on the drained (effective) and minimum undrained strength. The Factor of Safety (FOS) calculated for the embankment utilising the traditional limit equilibrium (LE) method indicated the application of undrained strength function for the residual soils can provide a significant optimisation for the embankment design compared to adopting a constant undrained shear strength ratio or constant undrained shear strength in the design.

Jul 1, 2021

By I H. Wilson

After decades of turmoil, Rwanda launched its Vision 2020 in 2000 aimed at reconstructing government and addressing poverty. Implementation focused on the agricultural sector, infrastructure and education. Later economic development and poverty reduction strategies recognised that expansion of tantalum, tin and tungsten mining could potentially diversify Rwanda’s economy and improve the balance of trade. In 2005, comprehensive environmental legislation requiring environmental impact assessment for all new mines was introduced. Since 2006, government-operated mines have been privatised and illegal artisanal miners encouraged to form cooperatives. The government passed a new Mining and Quarry Exploitation Law in 2008 and approved a new Mining Policy in 2010. This policy was influenced by the Africa Mining Vision (AMV), which the African Union approved in 2009 to ensure African countries obtain reasonable benefits from exploitation of their mineral wealth. The Rwandan mining industry has grown significantly over the last five years and the second economic development and poverty reduction strategy, released in September 2013 forecasts a further three-fold increase in production in the next five years. The strategy prioritises the mining industry and proposes new legislation, better information, greater transparency, encouragement to investment and use of best environmental and technical practices. It also proposes that Rwanda develop a ‘green’ mining sector featuring a ‘model’ mine that is fully funded through green investment and incorporates renewable energy systems, water treatment systems, forestry schemes and local training. Many international development partners have contributed to the current legislative framework and are monitoring environmental and social performance of mining in Rwanda. Local communities have generally benefited from mining and the new mines show improved environmental performance. The major challenges are dealing with the legacy of past haphazard mining practices and establishing linkages between the mines and local industries to create broader economic development.CITATION:Wilson, I H, 2014. Rwanda and the Africa mining vision, in Proceedings Life-of-Mine 2014 , pp 427–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By P Fuller, A R. Penney

Re-commencement of mining in the Western Zone of Beaconsfield Gold Mine following a seismically-induced rockfall fatality in April 2006 required a change of mining method involving drilling and blasting from specially developed drives in the footwall of the orebody. Broken ore is mucked remotely from ore drives on each level. Support in the footwall drives is required to maintain stability during their development and as stopes are retreated, which increases induced stresses and further seismic events are triggered. The paper outlines the challenges involved and methods used to select the footwall drive support to handle both static and dynamic load demand. The importance of load development in the support system, its displacement capacity, the compatibility of support elements and energy absorption capacity of the support system are highlighted. It is usual in any support selection process to ensure that capacity exceeds demand to create a factor of safety. In this case the demands on the system relate to load, displacement and energy absorption and the support system capacity for each must ensure that appropriate factors of safety for each are achieved. The paper shows how these factors are not independent and that selecting a high factor of safety for load can lead to compatibility problems with support elements in the support system.

Jan 1, 2008

By P C. Miclea

Transportation networks extend every day around the world, requiring safe and well-maintained structures for efficiency and for users’ safety. Due to specific features of the infrastructure, such as longer tunnels, increased traffic and marginal safety rules, fire safety in rail and road tunnels becomes more challenging.The situation becomes more critical due to the global economy and increasing worldwide tourism, with multi-national companies often involved in both design and construction of transportation routes or systems in other countries. Tourism brings the risk of visitors becoming victims in a foreign land; thus, international law becomes more and more applicable to transportation projects all over the world, requiring a consistent approach to safety (UN Economic and Social Council, 2001; US DOT Federal Highway Administration (FHWA) 2006; US Transportation Research Board, Committee on the Role of Public Transportation in Emergency Evacuation, 2008; UK Parliamentary Office of Science and Technology, 1997).There are significant differences between rail and road tunnels, both in their functionality and safety requirements. Most tunnels over a certain length are equipped with emergency ventilation systems capable to control the spread of smoke by creating an air stream in the desired direction. Besides ventilation, fire-life safety (FLS) includes smoke and heat detection by linear or spot detectors, closed-circuit television (CCTV) and public address systems with prerecorded announcements, as well as evacuation signage and monitoring capabilities (Vägverket – Swedish National Road Administration, 2004).There isn’t a consistent, worldwide approach to the design of emergency ventilation systems for tunnels, with significant differences from continent to continent (US DOT Federal Highway Administration (FHWA), 2004, US Federal Transit Administration, Transportation Research Board, 2006). In North America US NFPA 130 and 502 standards for rail and road tunnels, respectively, represent the main criteria, however, they are continually revised and new versions issued every three years. For road tunnels the World Road Association PIARC issues guidelines, but they are not truly enforceable. There are no similar international guidelines for rail tunnels, except general recommendations by the International Association of Public Transport (UITP) (IAPT, 2003).In Europe the Directive #54/EC adopted by European Community Parliament in 2004 requires a minimum level of safety for road tunnels users in all existing and proposed tunnels in the Trans-European road network that are greater than 500 m in length. Authorities having jurisdiction in many other individual countries, such as Australia, Austria, Germany, Japan and others, enforce specific safety regulations (Miclea et al, 2007). While it is impossible to summarise all aspects of this topic in a short paper, a review of the design approach, the existing differences in safety requirements, as well as applicable design solutions to meet safety codes for both rail and road tunnels are discussed below.

Mar 8, 2011

By C J. Greet, J Kinal, C Hitchen

Following the successful completion of a marked ball test defining the potential wear benefits the high chrome alloys may offer against forged steel, as well as laboratory test work investigating changes in pulp chemistry and improvements to metallurgical performance, a plant trial was commissioned at NewcrestÆs Ridgeway concentrator. The paper briefly describes these results.Newcrest decided to convert their media charge by the top-up method. To monitor the trial a sampling protocol was put in place whereby the pulp chemistry was monitored before, during and after the purge. The metallurgical shift data was analysed using various statistical methods to determine if the metallurgical performance had improved with the change in grinding media. While the analysis indicated that the metallurgy had improved, not all of the benefits could be assigned to the change in grinding media alone. However, the combination of reduction in media wear and the increases in copper and gold recoveries suggested that it was economically viable to operate with high chrome grinding media.As with many trials of this nature the prevailing economic conditions are fluid and a decision was made to revert back to forged steel grinding media in an effort to reduce operating costs. It was further agreed that Magotteaux could monitor the pulp chemistry and metallurgical changes in this reverse trial to confirm the results observed in the earlier conversion to high chrome grinding media.CITATION:Greet, C J, Hitchen, C and Kinal, J, 2012. Conducting high chrome grinding media trials at NewcrestÆs Ridgeway Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 56-64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By R Stimpson, B Johnson, B Hesse

During a period of twelve months between FY18-19, a series of trials were conducted to compare production drilling accuracy using two different methodologies, and the subsequent impact this had on stope performance (dilution and recovery). Testing was conducted at a series of underground mines in Australia. The drill rig’s existing alignment processes were compared to a new technology system, with the following observations: • The new technology was proven to limit rig alignment error, thereby reducing average blasthole deviation, resulting in an increase in the number of holes drilled within tolerance by up to 160%. • The increased accuracy reduced stope dilution significantly by reducing over-break of subgrade ore, whilst also increasing drilled meters (faster stope-cycle time), reducing the bridged tonnes ratio, and facilitating the capture of previously uneconomical stopes. A cost-benefit analysis extrapolated from each of the trials showed the extent to which the new technology, when applied to production data, reduced average dilution, increased ore recovery as well as general drill and blast productivity. In one such trial, the new technology was proven to have reduced average dilution by net 45.4%, which if applied to a full year’s production data, would result in AUD8.2M additional ore recovered, with AUD4.5M less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 to AUD106. This improvement was maintained over the following 12 months – reducing average dilution from 22% in FY17 to 12.1% in FY19.

Mar 15, 2021

By J Franz, S Bock, N Hentrich

Artificial ground freezing is the unrivalled method for groundwater control during mine shaft sinking. Moreover, ground freezing may also provide temporary ground support. The fast development of fibre-optic temperature monitoring devices, three-dimensional freeze pipe survey methods and numerical modelling software provide grounds for developing new and reliable tools for ground control during freeze shaft sinking. This paper presents examples of predictive numerical models that are based on back-analysis and calibration of temperature data that covers the complete construction cycle from pre-freezing through to artificial thawing. The back-analyses showed that standard numerical models are not capable of predicting the prevailing thermo-mechanical conditions satisfactorily. This paper describes the development and implementation of new tools for improved consideration of concrete hydration and latent heat, along with the introduction of other algorithms that improve and simplify the efforts of managing complex numerical models. A function is presented that allows for an automated correction of the model’s mesh based on results of three-dimensional freeze pipe surveys. This paper demonstrates that the latter consideration is important, because the often employed assumption of idealised freeze circle geometry in numerical models impacts on the accuracy of such model’s predictions. Subsequently, the verification of these extended numerical models is demonstrated. Due to its flexibility, the FLAC3DTM code was employed for the numerical modelling. This software provides the possibility of implementing additional functions written in internal FISH or Python language into the models. It is concluded that state-of-the-art techniques for freeze hole drilling and surveying, on-site monitoring and advanced numerical analysis provide a significant potential for both the design and the operation of largescale ground freezing measures. The application of the extended numerical models for predictive simulations during construction allows for temporary shaft lining optimisation, for assisting in operational decision making and for compensating temporary loss of monitoring data. Suggestions are made for required future work in order to further improve the developed ground control tools. CITATION:Bock, S, Franz, J and Hentrich, N, 2018. New tools for ground control in freeze shaft sinking, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 393–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Allen, B Oats, S Palaniandy, M Lollback

The Julius Kruttschnitt Mineral Research Centre has conducted an intensive VertiMill® (VTM) survey program at the Cannington mine concentrator as part of the ‘collaborative research in stirred milling technology’ program funded by Metso Minerals. Since 2003, Cannington has progressively added grinding capacity into the circuit through VTMs operating in secondary and regrinding duties. Cannington was one of the first mines to adopt this technology in secondary duty by installing two VTM-1500-WBs as part of a capacity expansion to produce sub-100 µm rougher feed. Subsequently, an additional VTM-800-WB was installed in the lead regrind circuit to prepare sub-20 µm cleaner stage feed.Several surveys were carried out to evaluate the VTM performance over a range of changed conditions. Among the key changes in operating variables were circuit power draw, feed rate and water addition to the bottom of the mill. The average specific energy for secondary duty was 3.7?kWh/t. The lead and zinc regrind mills consume 8.1 and 15.3 kWh/t respectively. Generally, the VTM installations have successfully prepared feed for rougher and cleaner circuits by reducing the top size into the floatable regime with steeper particle size distribution, which has led to enhanced recovery. The survey results show the success of VTM installations in secondary (receiving feed from autogenous circuit) and regrind duties.CITATION:Palaniandy, S, Powell, M S, Hilden, M, Allen, J, Kermanshahi, K, Oats, B and Lollback, M, 2014. VertiMill® performance updates in secondary and regrind duties at Cannington mine, BHP Billiton, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D Kilkenny, D Nardini, P Kline

This paper is a case study highlighting learnings and success in two areas challenging underground miners: change management and collaboration. It examines the implementation process of a new automated loading system in the bulk stoping area of Telfer Mine in Western Australia, controlling multiple load haul dump machines. Here, the new technology has brought together different functions and different companies to deliver a well performing automation system in a changing and challenging mining environment. The introduction of a new and different technology on site has driven collaboration between all stakeholders to break down the traditional barriers to achieve the sustained performance required. Historically, different teams have operated within silos and not always aligned to deliver a ‘best for project’ solution. Technical teams focus on the mine design, maintenance teams focus on reliability and operations execute the plan. Mining contractors focus on productivity and cost. Manufacturers focus on supply of goods and service. Optimising each silo individually is not guaranteed to provide an optimal mining solution. Involving elements from each team as seen at Telfer, has resulted in an optimal mining solution for the automated loading system. A change of focus from the technical teams to include automation parameters in the mine design; operability and maintainability built into the system design allowing for collective ownership and responsibility resulting in a more resilient solution. The implementation of the new technology was not only a technical change but more importantly, successful management of change. Elements of successful change management such as communication, vision, leadership and planning, are essential to harness a trusting site culture which is responsive to new technology. Learnings and challenges from this change process will also be discussed with the intent to improve the success rate and timelines of technology implementations in the future.

Mar 15, 2021

By R Norris, M Dunne

Substantial efforts by the industry, as well as by process and equipment designers, have resulted in many innovative developments that provide cost effective reductions in water usage. This paper showcases four emerging best practices in industry including examples of recent installations. Belt press filters are a small fraction of the operating and capital cost of alternative ædryÆ tailings technologies. This gives operators who must ædryÆ their tailings a competitive advantage and makes such operations much more sustainable. The new generation of belt filter presses use less energy, produces lower cake moistures and better disposal stacking properties. The need for tailings storage facilities may be eliminated or in some cases high-grade tailings can be dewatered and sold as a low value product. Mining applications include sand tailings, sinter plant waste, coal tailings and power station fly ash. Flip-flow screening machines are proven worldwide in the dry classification of coal and other minerals, reducing the size of beneficiation plants, whilst reducing energy, water demand and media consumption. They also allow the screening of wet/sticky materials not able to be sized using conventional screens. Lamella separators are used for toxic water clarification and/or sludge thickening in many downstream metal industries with the underflow often dewatered in a belt filter press. Such low cost, high capacity thickeners could also be used instead of conventional thickeners at smaller mines. The simple and reliable continuous washing upward flow (CWUF) sand filters have been used for treatment of waste water from coal preparation plants and steel works as well as in the production of potable water. The filtered waste water from mining processes can then either be reused or discharged from site. Other installations include cleaning mine water to prevent the blocking of dust suppression spray nozzles.

Jan 1, 2006

By S Maryati

Surface mining activities disturb large areas, produce great sediment loads and tend to be a source of water pollution if they are not managed properly. Coal mining in Indonesia has a very high risk of soil erosion because the coal mining areas are generally located in tropical areas with a high average of rainfall (4000 - 6000 mm/year) and use surface mining methods. The main factors affecting erosion risk are climate, soil type, topography, vegetation cover and management factors. Thus, the monitoring of erosion risk in mining areas is very important due to the characteristics of coal mining in Indonesia. The objective of this research is to determine the ability of satellite images (remote sensing data) and geographic information systems (GIS) to provide an accurate and up to date spatial database for the monitoring of erosion risk in surface coal mining areas using the Universal Soil Loss Equation (USLE) method.The erosion risk analysis and spatial data processing are generated by the ArcGIS 9.3 software and need several data, namely: an erosivity map, erodibility map, a slope map, vegetation index map and land management or land cover map. The erosivity map is derived from the rainfall data, whereas the erodibility map is derived from the soil map. The slope map is derived from the SRTM-DEM (Shuttle Radar Topography Mission-Digital Elevation Model) and processed using 3D analyst tools. Furthermore, the vegetation index map and land cover map are derived from a satellite image using digital image processing techniques.This preliminary study produced results that show soil erosion monitoring, which is integrated with remote sensing and GIS technologies, has great potential for producing accurate, advance, and low cost erosion risk maps in coal mining areas. This map is very important for getting spatial distributions of the erosion and useful for developing erosion management plans.

Nov 22, 2011

By R Norris, M Dunne

Mining and mineral processing is expected by society and obliged by law to operate in an environmentally friendly fashion, minimising the impact on and avoiding damage to the environment. Substantial efforts by the industry, as well as by process and equipment designers have resulted in many innovative developments, which show that operating in an environmentally responsible manner can be achieved in a cost-effective way. This paper showcases five emerging equipment best practices in industry including installation examples. Flip-flow screening machines are proven worldwide in the dry classification of coal and other minerals, reducing the size of beneficiation plants whilst reducing energy, water demand and media consumption. They also allow the screening of wet/sticky materials not able to be sized using conventional screens. The belt press filter is a small fraction of the operating and capital cost of alternative dry tailings technologies. This gives operators who must dry their tailings a competitive advantage and makes such ægreenÆ operations much more sustainable. The filtercake is disposed with other plant rejects, eliminating the need for tailings dams to be constructed and thus also often increasing mine reserves. Mining applications include coal tailings, sand tailings, sinter plant waste and power station fly ash. Screen-scroll and vibrating centrifuges are widely used in the coal, potash and salt industries to dewater the product to low surface moistures. Inclined plate Lamella separators are used for toxic water clarification and/or sludge thickening in many downstream metal industries with the underflow often dewatered in a belt filter press. Such low cost, high capacity thickeners could also be used instead of conventional thickeners at smaller mines. The simple and reliable continuous washing upward flow (CWUF) sand filters have been used for treatment of waste water from coal preparation plants and steel works as well as in the worldwide production of potable water. The filtered waste water from mining processes can then either be reused or discharged from site. Other installations include cleaning mine water to prevent the blocking of dust suppression spray nozzles.

Jan 1, 2006

By C Hawtin, B Miller, D Ashton

Ernest Henry mine (EHM) is an Iron oxide copper-gold sublevel cave mine located 30 minutes north of Cloncurry in North-West Queensland. The underground mine lies beneath open pit excavations, which were in operation from 1999 to 2011. Fault structures carry large quantities of water from the cover sequence aquifer into the underground mine area. The open cut excavations exacerbates vulnerability of the underground mine to the high intensity wet season storms of northern Queensland. These factors combine to make hydrogeological issues high priority for mine operation. Water-related risks include the cost of removing water from the mine, flooding risk and mud rush potential.Turnover of key technical staff in late 2015 at EHM resulted in the mine being left in an untenable position of losing the primary source of technical knowledge. Due to encouragement of cross-disciplinary activity coupled with workload and resource sharing, the management team were confident in utilising on-site personnel to offset loss of experienced personnel.Remaining geology personnel took additional responsibility for hydrogeological monitoring equipment and planning of upcoming work. Consultant input was limited to review only and an emphasis was placed on knowledge transfer to the geology team. Using this strategy, a 13 hole dewatering program was successfully implemented, achieving a significant water level drop in areas of elevated hydrological risk, whilst also upgrading the hydrological monitoring sensor array.Through a development program centred on cross-disciplinary exposure, the technical team was able to retain key technical knowledge despite staff turnover and produce strong results outside traditional training and roles. This paper serves as a case study on the methods, strengths and drawbacks of putting a focus on cross-disciplinary exposure as a method to combat staff turnover.CITATION:Ashton, D, Miller, B and Hawtin, C, 2017. Go with the flow – managing hydrogeological staff turnover at Ernest Henry mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 129–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By P Wahyono, H Vega, S Riza, P Vergara, P Gonzalez-Carbonell

PT Freeport Indonesia (PTFI), operating in the Ertsberg Mining District in the Province of Papua, is developing the Grasberg Block Cave copper-gold mine. The site aims to output 160 000 t/d and will be located underneath the current Grasberg Open Pit. Initial studies of the potential to develop a block cave mine in the Grasberg orebody have revealed that the mine will require significant volumes of air. The Grasberg Block Cave (GBC) project requires four primary fans (3750 kW each) to support production at full capacity.Fan #1 commissioning was accomplished successfully on 9 February 2012. However, Fan #2 chamber, which is separated by a 20 m pillar, had not been completed. The main challenge was Fan #2 chamber still needed to be benched. The risk of damage to the critical infrastructure in Fan #1 chamber, including ground support, cracks in pedestals, and misalignment in the impeller shaft were considered. The challenges were blasting the bench without damaging the surrounding infrastructure, completing the work safely and meeting the schedule. This was achieved with the engineering control methodology. This paper summarises the benching process of Fan #2 chamber and its impact upon Fan #1.CITATION:Vega, H, Riza, S, Gonzalez-Carbonell, P, Wahyono, P and Vergara, P, 2013. Excavating an underground primary fan chamber that is adjacent to a fully operational primary fan in PT Freeport Indonesia's Grasberg Block Cave Mine, in Proceedings The Australian Mine Ventilation Conference , pp 115-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By S Gomez-Hernandez, P D. Munro

Filtered dry stack tailing storage facilities offer many advantages over thickened tailing storage facilities and yet, most of the mining companies still prefer the latter.Some of the advantages of filtered dry stack tailing storage facilities are: increased structural integrity of the tailing storage facility, which is even more critical in areas of high seismicity, close to nearby communities or environmentally sensitive areas; maximised water recovery which is particularly important in arid environments where water is an extremely valuable resource and its supply is regulated; optimised recovery of valuable metals in the process water, avoiding high cyanide concentration going to detoxification (both aspects haven’t been emphasised enough in technical papers on this subject); optimised space to store the tailings in mountainous regions; minimised elevation of embankment height, providing a safe option to store the tailings in places where there is limited area available; simplified license approval to operate where the tailing facility is a big issue; and avoidance of potential problems with nearby communities.Filtered dry stack tailing storage facilities have some disadvantages such as: technology limitations in operations that process high throughputs (eg >50 000 tpd) as they require many filters resulting in high maintenance and operating costs; higher capital cost; low efficiency in the filtration process, particularly in ores with high clay content increasing operating problems and capital cost; the new technology risk with possible debottlenecking issues and a longer time to achieve the design throughput; and the need to treat larger water flow rates when the water balance is negative.This paper analyses: the operating practices of Mexican gold and silver operations using filtered dry stacking storage facilities; implementation issues, advantages and disadvantages; quantifiable reductions in gold and silver losses and actual lower detoxification cost; and current trends to use filtered dry stacking storage facilities in new projects. The data gathered raises questions about (a) the need to collect data on tailings filterability, and; (b) reducing the current high operating cost of tailings filtration.CITATION:Espinosa-Gomez, R, Gomez-Hernandez, S and Munro, P D, 2018. Tailing filtration practices in Mexican gold and silver mines, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 275–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A Price, D Okle, K Brooks

The operation of flotation plants has been improved over the years by use of fundamentally based design techniques, a better understanding of reagent chemistry, online metal analysis and the use of digital control systems. However, optimal operation of flotation banks is not consistently achieved using manual operation. The reason for this is that the system is a highly interacting one, with changes in air addition, cell interface level and reagent dosages all being available, without it necessarily being clear as to which change should be made for a particular situation.This situation is made more complex by the fact that the feed to a flotation bank can vary in flowrate, composition and density over a fairly short period of time. It is not possible for a human operator to reject these disturbances, given the extent of the operation that is typically being monitored.Model predictive control (MPC) is a control and optimisation technique, developed in the oil refining industry, that aims to manage just such interacting multiple input multiple output (MIMO) systems. This technology makes use of linear dynamic models of the plant, that are experimentally derived. These models are then used in a receding horizon strategy to determine an optimal trajectory of the inputs to the system.MPC has been applied to four areas of the lead zinc flotation unit at Mount Isa mines. A total of 31 cells are being controlled by the system, which varies air to the cells, levels and reagent addition on a minute-by minute basis. The MPC controls concentrate and tail grades, reagent dosages, as well as recoveries to ranges set by the plant metallurgists.The development of the MPCs is discussed, together with the benefits realised. The key factors in insuring an ongoing return on investment are described.CITATION:Price, A, Okle, D and Brooks, K, 2018. Glencore Mount Isa lead zinc flotation circuit – experiences from the implementation of model predictive control, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 101–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By P Vaikkattil, K Li, J Bullock

Unlocking maximum value is essential when designing a stope and the associated drill and blast packets. This is becoming increasingly important at Olympic Dam as the operation continues to expand south into the new mining areas away from existing infrastructure, increasing operating costs and required capital investment; into areas with less competent ground conditions, requiring smaller stopes and increased interactions. The introduction of Orica’s WebGenTM system is one way in which Olympic Dam can continue to unlock value into the future by decoupling traditional drill and blast limitations. The Lime 390 stope was the first stope at Olympic Dam to trial the new technology on the last blast packet. This paper reviews the drill and blast design of the Lime 390 stope, including the technical and operational challenges associated with the stope and the trial of the Orica’s WebGenTM system for the firing of the last blast packet.

Mar 15, 2021