Search Documents

By T J. Sullivan, H Pinkster, G Swarbrick

From 2002 to 2006, longwall mining was undertaken directly beneath the Cataract Tunnel, which is a 100-year-old, heritage-listed tunnel in Hawkesbury Sandstone responsible for delivering 20 per cent of Sydney’s annual water supply. At one location, undermining resulted in movement of at least 350 mm along a known fault that transects the tunnel. During this movement, the continued operation of the tunnel was ensured through a careful system of planning, monitoring and management.Of key importance to the success of the operation was the use of advanced numerical modelling to guide operations at all levels, including feasibility assessment, pre-mine mitigation works, monitoring design, operation performance and post-mining condition. This allowed many aspects of the potential impacts to be explored, including joint movements, rock mass deformations and changes in permeability. A key challenge was to successfully model near-field influences on adverse geological structure due to very far-field effects. This paper explains the model’s conceptual development, calibration, performance and limitations.Modelling provided the confidence to manage the impacts of large mining-induced movement on key infrastructure and ultimately predicted fault movement accurately. The fault movement remains one of the highest ever recorded due to mine subsidence.CITATION:Swarbrick, G, Sullivan, T J and Pinkster, H, 2014. Longwall mining beneath critical infrastructure – prediction versus performance of the Cataract Tunnel, New South Wales, Australia, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 157–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By L Klemettinen, J Biswas, W Malan, D Sukhomlinov, D Lindberg

In order to mitigate the effects of climate change, our society must be able to drastically reduce its CO2 emissions. As the metallurgical industry is a considerable contributor to these emissions, new greener technologies must be invented and developed. One option could be the direct production of metals from oxides using renewable electricity. The aim of this study was to investigate the possibility of using high-temperature molten oxide electrolysis (MOE) for iron and ferrochrome production. FactSage™, ver 8.2 (by Thermfact Ltd and GTT-Technologies) was utilised for estimating a feasible equilibrium electrolyte composition, and the experiments were conducted at 1550–1580°C in conical alumina crucibles with iridium wire as the cathode and platinum wire as the anode. The sources of iron and chromium were either pure FeO powder or industrial chromite pellets. Voltage was applied to the electrolysis cell for 6 hrs and the resulting current was measured, along with oxygen concentration in the off-gas line. The electrolyte comprised of SiO2, Al2O3, MgO and CaO. First, the effect of FeO concentration on iron reduction efficiency was investigated using only pure oxide powders as starting materials. The results indicated that 10 wt per cent FeO mixed with the electrolyte resulted in more efficient iron reduction compared to 20 wt per cent. In further experiments, industrial chromite pellets were ground and mixed with the CaO-free electrolyte. Iron and chromium reduction efficiencies were higher when approximately 19 wt per cent of the total sample mass consisted of pellets compared to increasing the pellet amount to 37 wt per cent. Generally, the chromium solubility in the liquid electrolyte was relatively low, and most of the chromium was confined to the spinel solid solution, from where its dissolution to the liquid electrolyte was very slow, resulting in slow reduction kinetics. For larger scale applications, economically more viable electrode materials should be investigated.

Jun 19, 2024

The lignites of Otago and Southland offer a potentially viable future feedstock for electricity production and possible conversion to petrochemicals or liquid fuels. The deposits, when combined, represent New ZealandÆs largest energy inventory; equivalent to about 74 000 petajoules û or approximately 35 times current natural gas reserves. Too often dismissed as irrelevant to New ZealandÆs energy future because of adverse perceptions of the value of low rank coals, the strategic value of this resource is in fact huge.   Investigations of the lignites extend back over more than 50 years (LFTB various, CRL Energy Ltd). Whilst it is not the intention of this paper to review this work, these investigations have confirmed the suitability of the resource as a feedstock for thermochemical conversion. Current estimates of South Island lignite mining costs are NZ$1.0 - 3.0/GJ (Natusch 2005), making these resources amongst the most competitively-priced energy sources available world-wide.   This value, however, will only be captured if we as a country begin to envisage a world-scale, long-life, integrated and multi-faceted development sized to supply world markets for chemicals or fuels. Recent CAE studies (Hooper and Riddolls, 2005) have emphasised the vital importance of ensuring that any exploitation of this resource maximises their value to New Zealand. The question that thus must be applied is how might large-scale utilisation of the resource fit with New ZealandÆs primary energy supply, and its potential for the export of high-value commodities.   From the broader perspective of New ZealandÆs total energy supply equation we need to examine other supply options beyond just the generation of electricity. We face in this country a situation wherein almost all our liquid fuels feedstock has to be imported with projections for an increasing dependence on imported oil. In addition NZ has a natural gas reserves-to-production ratio of less than ten years, and dwindling supply from local production. Without further natural gas discoveries, New Zealand has only a window of approximately five years before we will need to commit to imported LNG or some other thermal fuels option.   In other words, New Zealand is facing an uncertain future unless we can restore energy inventories to cover an adequate strategic reserve capacity as well as enable long-term investment in alternative sources. Within this context the South Island lignite resources are thus deserving of more attention. The extent of the resource is well known, its suitability for conversion reasonably assessed, and its magnitude such that there is little doubt that lignite conversion could adequately meet NZÆs future energy needs for many years out.   This paper reviews coal gasification technology, its application to lignite and the possibilities for future development of the lignite resources. It is argued that the strategic imperative for this country is to secure the lignite resources as a primary energy source for this country well into the latter half of this century.

Jan 1, 2005

By S McEachern, J Lowe

An important issue currently facing the mining industry in Australia is the management and cost to the industry and other stakeholders of entry into and exit from towns and their communities. These costs can be environmental, social, economic, political or reputational. The ability of companies to engage the trust of stakeholders, including: communities, governments and investors, is critical, and corporate reputation plays a significant role in this. For the industry to secure a long-term and sustainable future, it must have the technical, business and reputation assets to proceed in a cost-effective, environmentally acceptable and socially supportive way. This research assesses reputation as a critical competitive issue for mining companies, as technology and information make mining more predictable; the physical and human assets of mining companies are less likely to be the critical resource in a Resource Based View model of competitive advantage. The proposition is that in mining today, reputation as it facilitates day-to-day operations, regulatory zeal and access to new mine sites will become the rare, inimitable and valuable resource for mining companies. This paper reports on an ongoing research program to evaluate the impact a mining companyÆs reputation(s), with its various stakeholder groups, has on a companyÆs ability to sustain competitive advantage. Integral to this study is to develop an understanding of the relationships between mining companies and their stakeholders, and the importance of corporate citizenship polices to reputation and hence to corporate sustainability. Through the identification of the drivers of reputation for the various stakeholder groups, a model of reputation formation will be developed and also reputation measures for the mining industry in Australia. The preliminary findings of this research, the results of an industry focus group conducted with representatives from regional mining operations, are reported. The industry focus group was designed to enable a better understanding of who are the main stakeholder groups and how they regard mining companies and to inform the second stage of the research project a Delphi Study of the drivers of reputation by stakeholder groups. The aim of this research is to further the understanding of the relationship between corporate citizenship, reputation and performance in the mining industry, thus assisting companies to strategically manage their corporate citizenship investments.

Jan 1, 2006

By G Kirk

Definition and delineation of in-pit ore and waste material are the most significant tasks for an open pit production geologist; adding or destroying value in the mining value chain. Anglo American’s Mogalakwena Platinum mine, an open pit operation in South Africa moving 100 Mt/a, has recognised the value of improved material definition and is in the process of changing from blasthole to reverse circulation (RC) sampling for in-pit grade control. This is aimed at obtaining more representative samples, which are required to maximise ore recovery, minimise waste dilution and to increase the accuracy and confidence of production forecasts. Early in the project, it was realised that the key risks for implementing RC grade control were related to change management processes, rather than failure of technology. Recognising the importance of this issue, Mogalakwena chose an integrated implementation approach that incorporates all stakeholders of the mining cycle in order to develop a process that delivers maximum value and is sustainable within an active mining environment. The following core goals were addressed over five phases of project implementation: extensive definition and design of integrated project implementation, comprising: project buy-in and ownership from all key stakeholders, including survey, geology, mine planning, drill and blast, load and haul, maintenance, supply chain and finance; and detailed analysis of all potential issues and possible solutions, allocated to stakeholders as part of the scoping process; optimising hole patterns and drilling procedures, focusing on delivering maximum value for minimum cost using multiple scenario analysis from borehole data and operational sequencing requirements; and evaluation of lessons learnt during project implementation in order to optimise the technical solution and operational efficiencies. Although this project is not yet finalised, Mogalakwena Platinum Mine is already providing a blueprint for the effective development, implementation and optimisation of sustainable in-pit grade control RC drilling for other open pit mines within Anglo American plc.

Aug 22, 2011

By S Goff

The Northern Sewerage Project (NSP) is a $650 M infrastructure project that will increase the capacity of the sewerage system for Melbourne’s growing northern suburbs while also helping to protect the Merri and Moonee Ponds creeks by significantly reducing the number of sewage overflows that can occur after heavy rainfall. The NSP consists of two stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water Corporation, and Stage 2 (NSP2) will be owned by Yarra Valley Water and operated by Melbourne Water Corporation.Glass-fibre reinforced plastic (GRP) was used on both NSP stages, however, since Stage 1’s schedule for installation of GRP was slightly ahead of Stage 2’s, this paper will only focus on Stage 1’s use of GRP.NSP1 involves the construction of 7.9 km of new sewer tunnel ranging in diameter from 1.6 to 2.5 m, five main access shafts at depths of up to 65 m, and connections to the existing sewerage system including several access manholes. Construction began in 2007, and project completion is expected in 2012.The original design for NSP1 specified the use of high-density polyethylene (HDPE-) line precast concrete pipes as the final tunnel lining and HDPE-lined reinforced concrete for the access shafts and manholes. During construction, the rising cost of precast concrete pipes and the introduction of an additional GRP pipe supplier in the market justified a review of the tunnel final lining material. The contractor-proposed GRP pipe alternative was accepted for the final tunnel lining based on time and cost savings that were possible without compromising the design intent. After gaining experience with GRP through this design change, Melbourne Water Corporation reviewed and accepted GRP as the final lining for five smaller connection manholes. The use of GRP for the manholes was particularly inventive as the redesign made use of the approved tunnel GRP pipes as both a structural and corrosion-resistant lining.This paper discusses the use of GRP on NSP1; how the change in material, from concrete to GRP, affected the design philosophies assumed during detailed design; and how construction methods were modified to handle the less rigid GRP material. Details on the structural, hydraulic and durability considerations for the design are included, as are details about the time and cost savings and the quality and safety improvements that were achieved during construction.

Mar 8, 2011

By M Gerards, M Steinberg, T Graham

The quality and quantity of Australia’s secondary deposits, which include tailings streams and tailings dams, are higher than most countries’ primary deposits. In addition, these secondary deposits have already been mined and processed, meaning that the recovery of high-grade product requires low capital and operating costs.The most widely used process for the recovery of these valuable fine and ultra-fine hematite iron particles is the wet high-intensity magnetic separation technique, originally developed by Dr Jones over 55 years ago. Many of the original machines are still working today.The aim of this paper is to demonstrate the capabilities in terms of grade and yield of using sophisticated magnetic separation modules. All results and figures are obtained from test work and design and engineering work with material from the Pilbara. In addition, consideration is given to dewatering of iron ore product and tailings.Two types of tailings have been identified for processing. Firstly, tailings that have already been deposited in a tailings storage facility, and secondly, live tailings streams from an existing wet iron ore beneficiation plant. In both cases, the technical and practical results are shown along with relevant flow sheets and plant layouts. Finally, this paper highlights the total predicted power and water consumption, capital requirements and projected operating expenses.The results show that the operating costs are significantly lower than the mining and processing operations that are required for an equivalent amount of iron ore. The recovery of iron depends on various factors but is within the 30–50 per cent range at an equivalent grade to the mainstream product. Another significant benefit is that the magnetic separation process is water positive, meaning that water is released rather than added in the process.The processing of the Pilbara’s secondary deposits will therefore result in an overall reduction in operating costs, an increase in product yield from a plant, extend the life-of-mine and offer environmental benefits by reducing the tailings footprint and water usage.The quality and quantity of Australia’s secondary iron ore deposits and tailings are such that many other countries would judge these as equivalent to primary deposits. Furthermore, these tailings are already mined, available and liberated to such an extent that the recovery of a valuable product is highly economical in terms of capital expenses and operating expenses.CITATION:Steinberg, M, Graham, T and Gerards, M, 2015. Recovery of iron ore fines and ultrafines from tailings by using wet high-intensity magnetic separation – JONES WHIMS, in Proceedings Iron Ore 2015, pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C DahnTr-Lindqvist

The Kiruna mine produced about 19 Mt processed iron ore in 1999 using sublevel caving. General failure in the hangingwall has been widely studied and its mechanism is rather well understood. Failure in the footwall is more recent and not perfectly explained. Plane shear failure and Hoek and BrayÆs circular failure charts were successfully used to match the first surveyed failure surfaces. The footwall is not free yet but covered by a caved waste rock abutment whose exact behaviour is poorly known. Based on new field data and numerical models (FLAC), the following paper presents recent improvements in understanding the Kiruna mineÆs footwall failure process.

Jan 1, 2000

By A Kobzev, C Robben

Sensor-based particle sorting of gold ores is the masterclass of preconcentration. The technical challenges of a grade in ppm scale makes a direct detection with currently available technology in milliseconds impossible. Consequently, the detection and classification of particles into ore and waste classes relies on detectable proxies which are the foundation for the classification. These must be reliable and repeatable across the ore bodies processed in future. A sensor-based particle ore sorting equipment must therefore be calibrated systematically by understanding the gold deportation in different lithological groups. Also, it must be in best operational state to minimise possible misplacement. The technical challenges are met by a stringent financial regime governing the business case. Many gold ore sorting projects require a stable grade of gold in the rejected waste significantly below 1gr/t. Two examples are introduced in this paper:  The pilot results and operational experience of X-ray transmission (XRT)-based particle ore sorting for pebble sorting of sulphide associated ore;  Laser-based particle ore sorting for pebble circuit of an orogenic, quartz associated gold ore. Usually, sensor-based particle sorters are installed in the crushing section of a plant. However, for large capacity plants, the number of equipment required, and the associated material handling costs result in significant capital and operating expenses for plants with 1200tph run-of-mine capacity. As a conclusion, it was decided to investigate sensor-based particle ore sorting applied to the pebble stream of two existing semi autogenous mills.

Nov 10, 2020

By D La Rosa, D Bennett

"Exploration drill core provides for a number of standard measurements essential for determining the viability of a new mine or the extension of an existing one. Rock lithology and alteration can be visually determined and grade measured from the half core. Geotechnical parameters such as rock strength and structure can also be measured. Using suitable proxies, these metrics can then be used to estimate run-of-mine (ROM) particle size. In combination with comminution test results, these can subsequently be used to design comminution circuit configurations and estimate their performance.The Frieda River Project drill core for the large Horse-Ivaal-Trukai copper-gold porphyry deposit was unusual due to a late stage gypsum-anhydrite stockwork event that overprinted much of the deposit. Above the base of the oxidised zone, which closely matches the water table, gypsum and anhydrite has been leached out, effectively removing the glue holding the rock mass together. As a result, much of the rock above this gypsum-anhydrite surface is fragmented and gravel-like in texture, while the material below this horizon is typically uniform and competent.Large volumes of the orebody above the gypsum-anhydrite surface are expected to need minimal or no blasting for efficient excavation. In addition, the fragmented nature of much of the material was expected to reduce comminution specific energy as it already appears as though it has been crushed. While this was expected to have positive impacts to the operation, the lack of standard geological logging methods available to accurately define the degree of in situ fragmentation led to difficulty in gaining certainty over the ROM product and grinding circuit feed size distributions.Using the extensive library of core photos for the project, a novel method using image analysis techniques to take both the intact core and gravel into account to predict ROM fragmentation was developed. In addition, existing point load test data was used to infer the strength of the rock and its impact on the blasting, crushing and grinding processes. The novel approach allowed development of ROM size distribution data and improved certainty in the results of comminution circuit designs.This paper describes the methodology undertaken in detail, and discusses the results obtained.CITATION:Bennett, D and La Rosa, D, 2016. The Frieda River Project – a Novel Approach to Analysing Exploration Drill Core: How Broken is Broken?, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By H W. Wu

Occupational exposure limits for diesel particular matter (DPM) are progressively being adopted in a number of countries. Many of these follow the lead of the US Mine Safety and Health Administration initiated in 2008. In line with adoption of best practice it is accepted that all exposures should be reduced to as low as reasonably achievable. The management of diesel emissions and occupational exposures to those emissions requires an integrated strategy incorporating efforts from all key departments on a mine, including management, production, maintenance, supply and occupational health and safety.Australian coalmine longwall moves rely on the use of high-powered diesel equipment such as chariots and other machines that produce exhaust pollutants of gases and DPM. To reduce mine personnel’s exposure levels to DPM a hierarchy of controls can be followed. Minimising the use of diesel equipment, better operator positioning in relation to exposure source, using efficient engineering methods and adopting better ventilation to reduce concentrations through dilution are some of the controls that can eliminate exposures. Approaches generally adopted in Australian longwall mines currently rely on a combination of strategies such as optimisation of ventilation, use of diesel particulate filters and use of diesel tag boards that minimise the number of vehicles through recording entry and exit into working panels.A study has been undertaken into the mine ventilation systems currently in use during longwall moves within Australian modern longwall extraction mines. This paper reviews current longwall section ventilation systems and discusses evolving changes being adopted to address the more complex problems in dealing with section DPM during phases of the operational moves. The effects of DPM on crew members as well as the diesel equipment operators within a longwall section are examined. Issues that should be considered in designing the longwall section ventilation during the moves are discussed.CITATION:Wu, H W and Gillies, A D S, 2015. Review of ventilation optimisation strategies during longwall moves, in Proceedings The Australian Mine Ventilation Conference, pp 133–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Adhikari G. R, Raju N. M

The breaking of rock by explosives occurs so rapidly that the details of the phenomenon cannot he observed by the unaided eye. High resolution cameras and VCRs offer a means of slowing down the blasting action. A high resolution super video camera with digital zoom and a variable shutter speed was imported and used for the first time in India as a tool for blast optimisation studies at Malanjkhand Copper Project. Slow motion play-back revealed that the gases vented out through the fissures. The crest moved prior to the lower portion of the bench when initiated with detonating cord. The delay timing between the rows was not enough to provide sufficient relief and rock movement. This inadequate delay timing resulted in flyrock from the back rows. Stemming ejection was observed from practically all the holes. The muck profile was not satisfactory. A trial was carried out using 450 ms in hole delays and 25 nis surface delays. The front row holes were drilled based on the observations made from the laser profiling survey system. The video of the monitored blast showed that the rock started moving prior to the stemming ejection. It could be clearly seen that the entire block was completely initiated through the surface delays before the onset of the burden movement, thus eliminating any chance of misfires. Viewing blasts in high quality slow motion was useful to arrive at modified design parameters, resulting in uniform fragment size distribution and controlled rock movement.

Jan 1, 1995

By A Gustafson, D Johansson, K Jonsson

The underground mining process, from in situ characteristics of the unmined rock mass to the final mill product with fully liberated minerals, consists of a chain of unit operations. Some of them influence fragmentation while fragmentation impacts others. From a production point of view, fragmentation is a key parameter for the proper functioning of many unit operations and affects total production; it influences the ability to load, haul and crush the rock later in the process. Fragmentation varies because of rock mass strength, the presence of joints, the chosen explosive, specific charge (kg/m3) and quality of drill holes. The efficiency and result of unit operations such as drilling, blasting, loading and crushing depend on the rock properties, which vary throughout a mine. Generally speaking, operations are not well adapted to the actual rock properties, leading to a non-optimised flow in production. This paper presents the initial part of a project that will build knowledge on the impact of fragmentation on each step of the production chain in an underground mine. It identifies the key parameters of fragmentation, which influence the overall energy consumption and productivity in a mining operation through interviews, mine visits and a literature review. In the subsequent stages of the project, a number of field tests in the case study mine will address important segments of the production process where fragmentation is a major obstacle to improvements. Optimising the entire process, rather than isolated unit operations, will lead to increased productivity, decreased amount of interruptions and lower energy consumption.CITATION:Gustafson, A, Jonsson, K, Johansson, D and Schunnesson, H, 2016. From face to surface – a fragmentation study, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 555–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By G M. Zhomin, A S. Arkhipin, A Kondratiev

Viscosity of multicomponent slags is one of the crucial physicochemical properties for many industrial processes and technologies. While the viscosity-temperature relationship of completely molten slags can well be described by an Arrhenian-type law, the compositional dependence of viscosity is still not fully understood, especially in compositional regions with the lack of experimental data (eg at the glass-former concentration of 90 molar per cent or higher). In the present work major compositional relationships of the activation energy of viscous flow have been revised for numerous binary and ternary slag systems on the basis of experimental data collected and stored in the viscosity database OxiVis. For example, it has been found that the activation energy relevant to the polymerisation effect in binary systems of the MO-GFO type, where MO is the modifier oxide (ie monovalent K2O, Na2O, Li2O and bivalent CaO, MgO, BaO, MnO, PbO etc) and GFO is the glass-forming oxide (SiO2 or B2O3) is not always proportional to the third power of XGFO (contrary to the Urbain formalism) and can vary significantly dependent on the slag system. Also, the activation energy of the charge compensation effect has been revised for ternary systems of the AO-MO-GFO and AO-MO type, where AO is the amphoteric oxide (Al2O3, Fe2O3 or other). A simple polynomial model has been proposed on the basis of the carried-out analysis for estimation of viscosities of multicomponent slag systems. The model has been optimised against the experimental viscosities in the selected binary, ternary, and higher-order oxide systems and has been shown reasonable agreement with the experimental data.

Aug 21, 2024

By N Pirouznia, F Rashidi Nejad, S Naraghi

Sungun Copper Mine, which is the second largest copper mining operation in Iran has a large tailings storage facility with a seepage control dam located downstream of the main dam. Surface and groundwater in surrounding area of the tailings storage facility has been monitored for ten years. This paper will discuss the results of the surface and groundwater monitoring and seepage control at the Sungun Copper Mine. The results of the study show that if the tailings storage facility influence the water quality of the rivers, this effect is not significant, so that the prevailing parameters of the measured parameters were within the permissible standard of drinking water in Iran.CITATION:Rashidi Nejad, F, Naraghi, S and Pirouznia, N, 2018. Surface and groundwater monitoring and seepage control at the Sungun Copper Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 439–453 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By R Price, B H. Miller

"The rise of autonomous haul truck fleets may have been initially driven by the rapid escalation of the cost of equipment operators, but the actual improvements reported by the major iron ore miners far exceeds the simple reduction in workforce. Utilising cost models developed for feasibility studies and mining contract modelling, the limits of cost improvements due to simple labour reductions are compared to those achieved by the early autonomous fleet adopters and through traditional process improvement techniques such as fleet class upgrades or hot-seating of equipment. As autonomous fleet implementation matures, it is likely that the gains seen by current adopters will seem minor compared to the limits generally governed by the limit of equipment utilisation. This ultimate limit is explored through time utilisation models, which were also developed for use in feasibility studies and mining contract modelling.Citation:Miller, B H and Price, R, 2016. Autonomous Haul System Savings - It's Not about Less Truckies but Better Truckies!, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 2–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

The Wattle Dam gold mine, located near Kambalda in the Goldfi elds region of Western Australia has recently progressed to an underground operation and is now believed to be Australia's highest grade operating gold mine. At end of March 2010, the deposit had reserves of 132 000 t @ 20.8 g/t for 88 000 oz and by the end of June 2010 had produced 110 000 oz from open-pit and underground mining. The Wattle Dam main lode is characterised by very coarse gold mineralisation. Gold occurs as cm to decimetre fracture fi ll veinlets, shear surface coatings and erratic fl akey clusters. The gold has no quartz or silica association and lacks adjacent low-grade mineralisation or alteration assemblage. Geologically it appears atypical of Archaean lode gold deposits and may represent an extreme end member of the type. Definition of the lode is largely dependent on effective geological identification of the host lode zone and an understanding of the erratic distribution and grade behaviour of a high-nugget, coarse gold deposit. Dependence on assay data to defi ne the lode zone would result in the deposit being mined incorrectly and much of the deposit being left unexploited. This paper discusses the geology, coarse gold characteristics and defi nition methods which are used to successfully defi ne and mine the deposit.

Aug 1, 2010

Alluvial mining even of shallow deposits is often economically a marginal proposition and causes significant disruption of the land surface through the need for large scale excavation. In-situ leaching using chlorine-based solutions eliminates the need for excavation, the disruption of surface activities, and may greatly reduce processing costs and improve recovery especially of fine gold. A spreadsheet model has been developed to design and analyse the economics of in-situ leaching of alluvial deposits. In-situ leaching of shallow deposits may be achieved in a number of ways including solution infiltration via perimeter ditches or the use of injection and production wells. In most instances deeper alluvials may only be processed using well systems. Two deposits are analysed in this paper. The first consists of one metre of payable wash beneath one metre of overburden. Some thirty fields per year are treated processing 450 000 BCM per year at a cut-off grade of around $4/tonne ($8/rn3 or the gold value equivalent of 0.26 gh or 0.52 g/m3). The principal costs are well drilling and labour. Sensitivity analysis indicates that doubling the throughput halves the cost. The economics of the project are relatively insensitive to reagent costs and consumptions, and halving the recovery doubles the cut-off grade. Shallow deposits treated using the infiltration ditch system may be marginally cheaper and more conveniently managed although this depends on the relative cost of digging the perimeter ditches. In a second example, deep leads with one metre of wash beneath 30 metres of overburden necessitate significant drilling and feature reduced throughputs as a consequence. In the example chosen 30 fields a year are processed for an annual throughput of 65 000 tonnes costed at around $20/tonne (1.4 g/t Au equivalent, $40 /m3). Sensitivity analysis indicates that throughput, and drilling cost per metre are not important but there is a high sensitivity to recovery and to the depth to payable wash.

Jan 1, 1992

By Y Peng, D Wannas

In the fine particle flotation technologies being developed today the fine hydrophilic (gangue) particles are usually well dispersed. These highly dispersed fine particles can be recovered into the flotation froth product by mechanical entrainment. Flocculation of hydrophilic particles caused by polymer depressants could potentially reduce the mechanical entrainment of these particles. This paper reports testwork completed on fine particles of several solids, iron oxide, hydroxylapatite, galena and sphalerite, as well as on a relatively coarse quartz sample (-75+38 ¦m). Dodecylamine was used as a collector for the quartz, and several dispersants and polymer depressants, including sodium silicate, sodium metaphosphate, zinc sulfate, potassium dichromate, corn starch, corn dextrin and carboxymethyl celluloses (with molecular weights of both 700 000 and 80 000) were used as flotation modifiers. The major part of the testwork involved flotation tests in a 200 ml flotation column. Both water and solid recoveries were recorded. The degree of flocculation and dispersion was determined by settling tests in 250 ml graduated cylinders. It was observed that flocculation of the fine hydrophilic particles significantly reduced their mechanical entrainment, while dispersion severely aggravated it. Thus, in the flotation separation of artificial mixtures of the -75+38 ¦m quartz and fine iron oxide or hydroxylapatite, polymer depressants that caused flocculation were found to perform better than the ones that did not cause flocculation.

Jan 1, 2005

By T Ireland

The Rosedale Outfall Project utilised an earth pressure balance (EPB) tunnel boring machine (TBM) for only the second time in Auckland. Although the tunnel was excavated fully through East Coast Bays Formation (ECBF), the downhill gradient along with some unexpected areas of extreme water posed some significant challenges during construction.The Rosedale Waste Water Treatment Plant Outfall Tunnel project was commissioned in response to the growing needs of North Shore City, New Zealand. The outfall tunnel comprises a 3 km long segmentally lined tunnel and a 2.1 km buried marine pipeline, and discharges 2.7 km offshore. The capacity of the new outfall is 6 m3/s compared to the existing outfall capacity of 1 m3/s.Following previous project experience, and with the tunnel located along its full length in the bedrock weak sandstone/siltstone bedrock of the East Coast Bays Formation, tunnelling conditions were expected to be benign. However during construction six high inflow events were encountered, including a full face (3.4 m diameter) of Albany Conglomerate over a 48 m length of tunnel. This material comprised cobbles in an uncemented sand matrix, and inflows were recorded at over 25 L/s.This paper describes the design challenges on the project including the design of a steel fibre reinforced segmental lining for internal pressures. The specification of the machine is discussed including the modifications required to enhance the risk mitigation measures already in place. The ground conditions encountered are discussed and have improved the knowledge of the range of conditions that can be expected in Auckland.Despite the challenges presented during construction, excellent progress rates were achieved and the tunnelling was successfully completed ahead of program.

Mar 8, 2011