Search Documents

By D K. Weatherley, G R. Ballantyne, S Ali, M Yahyaei, M S. Powell

This paper explores development of a novel ore characterisation method for the precise measurement of practical minimum comminution energy. A monolayer of particles with a narrow size distribution is broken using a precision rolls crusher (PRC); an ore characterisation device developed to overcome the shortcomings of conventional tests. For energy measurement, PRC uses two shaftmounted rotary torque transducers. These transducers acquire precise torque and angular speed data in response to the load applied to the rotating shafts during breakage events, which is converted into energy. The test progressively crushes feed particles down to final product size in many controlled breakage stages. The generation of fines in each breakage stage is then plotted as a function of input energy. The inverse of the gradient of this plot provides the size specific energy (SSE) in kWh/t of material generated below a predefined marker size; -75 μm in this case. The PRC has potential to evolve as a geometallurgical ore characterisation test—it is simple, fast, requires small sample mass (200–300 g), covers a wide feed particle size range (10 mm to 115 µm), and provides ideal SSE measurements that can be used for the calibration of on-site production equipment.

Aug 24, 2022

By R M. Arellano, D M. W Harney, M Makhuvha

Mineral resource and ore reserve estimates are founded on two sources of data: tonnage and grade. The tonnage is a product of volume and density; both of which are estimates. Density impacts numerous operational factors, which include, but are not limited to, mine design, mine planning, equipment selection and operational performance. Hence, density is a significant parameter and its determination requires similar care as the measurement of grade. Selecting an appropriate method to determine density, and ensuring its rigorous application, thus reduces risk and can improve operational performance, which in turn increases profit margin.Different Anglo American sites use a variety of practices and protocols to determine density, which is highly dependent on the physical characteristics of the orebody, local conditions and historical practices. Also, individual sites sometimes execute the same method in a slightly different way, which may also affect the outcome of the measurements. In order to gain a better understanding of how density is determined at Anglo American projects and operations, a review of these techniques was undertaken. The objective of the study was to identify and share good practices across the company, as well as to look for improvement opportunities, where applicable. Ten different methods of measuring density, applied to nine different commodities, were identified and described. An additional technique was recently developed by Anglo American Technical Solutions. The core pycnometer is a large gas displacement pycnometer capable of measuring density at high accuracy on full pieces of intact core.This paper provides an overview of methods used to determine density within the Anglo American Group, including quality control and quality assurance aspects. It is not the purpose of this paper to identify a preferred method, but to highlight the importance of choosing the best suited practice for a project or mine site. In addition, a case study comparing two different density determination methods applied to the same rock samples from the Los Bronces Copper mine was undertaken and the results of that study are presented here.Selecting the most appropriate method to determine density and comparing results from two or more techniques against each other, together with other suitable quality control procedures, is considered to be of utmost importance for all mining operations and exploration projects.CITATION:Makhuvha, M, Arellano, R M and Harney, D M W, 2014. Determination of bulk density in Anglo American plc, methods and impacts, with a case study from Los Bronces Mine, in Proceedings Ninth International Mining Geology Conference 2014 , pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By H Turrer, M Badawi, R Belissont, Y Foucaud, E Kleiderer, L Southavy, J Mesquita, Y Basselin

The Mont Reed iron ore deposit, owned by ArcelorMittal, is situated approximately 140 km southwest of the Mont-Wright mine in the southern region of the Labrador Trough, Canada. Acquired by Québec Cartier Mining (QCM) in the 1960s, the Mont Reed mining property has remained unexploited due to the complex nature of the ore in the area. However, during the last years ArcelorMittal’s R&D team has been dedicated to developing a process to beneficiate the Mont Reed ore and produce high-quality pellet feed suitable for direct reduction furnaces. Extensive research revealed that achieving a good liberation degree of particles required grinding the material below 75 μm (P80 of 53 μm). To find the most effective technology for this task, a detailed comparison between ball mill and vertical stirred mill grinding was conducted. Both grinding technologies underwent detailed testing in bench-scale experiments. The ground products were comprehensively characterised, including size distribution analysis and chemical analysis per size fraction. Additionally, liberation analysis was performed using an automated scanning electron microscope (SEM). To determine the grinding specific energy, a method previously developed at Samarco (Brazil) for fine grinding of iron ores was employed. Furthermore, magnetic separation and flotation tests were conducted on the ground products. After a thorough evaluation of all the results, it was observed that both ball mill and vertical stirred mill grinding produced samples with similar physical characteristics. However, the vertical mill demonstrated higher efficiency in grinding the material. To conclude the study, an economic evaluation was conducted for both options considering various factors. Overall, ArcelorMittal’s R&D team’s dedicated efforts have brought them closer to unlocking the potential of the Mont Reed ore deposit and paving the way for its future utilisation to the production of high-quality pellet feed.

Sep 18, 2023

By D Johansson, C Yi

Blasting techniques are widely used to fragment rock masses into smaller pieces. Numerical modelling is an efficient method employed by many researchers in the blasting field. It is difficult for a conventional continuum-based approach such as the finite element method (FEM) to model the rock fragmentation by blasting and the expansion work on the rock by explosive and its detonation products. In this paper, the particle blast method (PBM) was employed to model the behaviour of the detonation and a bonded particle model (BPM) was used to model the brittle material to be blasted. A mortar cylinder with a centrally placed hole for the explosive was modelled and the results were compared to the experimental data. The blast process from crack initiation to fragment formation was analysed. The influence of coupling ratio on fragmentation was also investigated.CITATION:Yi, C and Johansson, D, 2015. Discrete element modelling of blast fragmentation of a mortar cylinder, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 793–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M K. Singh

Mining is nothing but an art - besides being a science - of extracting valuable minerals from the womb of the mother earth. In this gigantic task, a large number of machinery and equipment are employed judiciously. Wire ropes play a vital role in lifting or hoisting men and materials under hostile/adverse working conditions and constitute a major item of investment on machinery/equipment. The economy of using a wire rope is a concern for engineers, users and the planners. The economic use of wire ropes for mining purposes largely depends on the following factors;Mechanical design considerations - which include tensile strength of wires, elasticity, resistance to abrasion and crushing, fatigue values, static and dynamic loads on wire ropes, factor of safety, fleet angle, etc. Metallurgical consideration - Composition and heat treatment of wire materials, defects like inclusions and voids, surface quality factor, lubrications, micro structural parameters. Operational consideration - Seizing and cutting of rope, storage, care and maintenance, cutting back, etc. Environmental consideration - Temperature and humidity, pit condition, dust, corrosive atmosphere, etc. In the present paper, an attempt will be made to suggest steps for achieving optimum economy while using the wire ropes for extraction of precious minerals and coal keeping in view the points noted earlier. Once technical viability is established, economy is the ultimate consideration for an industry for safe hoisting of men and material.

Jan 1, 2000

By R Morrison, R Dunn

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the æAMIRA P754-Metal Accounting and ReconciliationÆ project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called æthe propagation of errorÆ.

Jan 1, 2007

The Marvel Loch Operations (MLO) plant was treating ores from up to six MLO sources and in addition needed to blend externally sourced ores with its own ores. This presented a metallurgical accounting dilemma, which was subsequently addressed by the design, implementation and testing of an automatic sampling system. The MLO automatic sampler was well designed and has been the subject of previous internal and external reviews. The sampling action is fully automated and the unit is essentially self cleaning particularly when sampling primary ores. The purpose of this paper is to document the rationale behind the design, the specific details of the sampling station, its use for ore purchase purposes and an assessment of the sampling system to meet the needs of the operator.

Mar 1, 2010

By E S. Weiss, S P. Harteis

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) has conducted full-scale explosion experiments, to evaluate the strength characteristics of various seal designs, used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests conducted within the multiple entry section of PRLÆs Lake Lynn Experimental Mine (LLEM) is currently the only accepted test method used by the Mine Safety and Health Administration (MSHA), for deeming a seal design suitable for use in American mines. These explosion tests are labour intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. The PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in situ testing of seals in an operating mine. Two chambers within LLEM and one within PRLÆs Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from these chamber tests compare favourably with those from the large-scale explosion tests in the multiple entries. In addition to testing seal designs at the required 20 psi static pressure level, the chamber test approach also allows for the determination of the sealÆs ultimate design strength. Size-scaling relationships for predicting the strength of seal designs as a function of entry size are also presented.

Jan 1, 2005

By F Weir, B Estrada

The impact of seismic loading on open pit slope stability in Australia is often only considered where the slopes are located adjacent to tailings facilities or other major infrastructure. The debate regarding application of seismic loading in open pit design in Australia is usually founded on limited reporting on significant damage of open pit operations during earthquakes, the common perception that earthquakes do not occur in Australia or that they are unlikely to occur during the mine life of the mine. It is frequently overlooked that pit slopes that have withstood strong earthquakes in highly active seismic regions are often designed under strict seismic guidelines. This paper discusses the factors that impact earthquake performance of open mine slopes. These factors include topography, slope geometry, rock material and mass properties, water management and intrinsic pit design. Further, the paper presents insights into the characteristics of earthquake activity in Australia such as magnitude distribution, earthquake depths, areas prone of earthquake activity and general seismic hazard that are relevant to pit design. Guidelines are provided on the conditions and circumstances under which earthquake design in open pit mining should be considered. In addition, this paper provides recommendation on the applicable methods for assessment of the impacts of earthquake loading on pit slope stability.

Jun 22, 2022

By H Rossiter, C Simpson, J Market, P Jeanneau

Downhole Assay tools are a geophysical method to collect an instigated response from the material surrounding a drill hole and deliver a multielement proxy-assay. They were first tested in the Pilbara at the turn of this century, however since 2011 they have seen a more focused testing and implementation regime with multiple companies across multiple Pilbara mine sites. The increase in the volume of data has led to advances in the measurements and significant improvements to the efficiency of the calibration process. Pulsed Fast and Thermal Neutron Activation Analysis (PFTNA) downhole assay tools collect gamma photon spectra which are characteristic of elemental signatures. One of the key components of the technique is calibrating the spectral signatures to lab assays. Each tool is slightly different due to the organic nature of the crystal detector and therefore responds slightly differently. Environment and hole conditions as well as ore characteristics are among other external influencing factors. Thus, a unique calibration is required for each tool. In addition, not all elements are measured directly, but some are actually characterised by proxy, meaning that if the signal-to-noise ratio for an element is small, it may be easier to identify the mineral or geology in which that element is found and thus infer the concentration of the element. These proxies may differ for each site or geology type within a site. There is a large advantage to build a unique calibration per tool at each site rather than a universal one to be used across the whole province. This then delivers the accuracy and precision of measurements that mining companies require for modern operations. Early work with the tool required several thousand metres of calibration data and several weeks of analysis to build each calibration. This process has now been streamlined to significantly reduce the amount of data required and the analysis time to make it much easier to introduce new tools to a site with an existing model or to create new models. This paper details the calibration process, illustrating the increasing accuracy of the models as training data are acquired as well as the methods for transferring a calibration from one tool to another.

Nov 8, 2021

Legislation introduced for Queensland and New South Wales Coal mines provides different levels of prescription regarding specification of mine seals û generally in relation to capacity to withstand overpressure. In Queensland, the Coal Mining Safety and Health Regulation (2001), Section 341 (d) places a further onus on the statutory ventilation officer to æensure all ventilation control devices at the mine are properly constructed and maintainedÆ and that the ventilation officer æmust ensure a ventilation control device mentioned in the regulation à and installed at the mine meets the design criteria statedÆ for the ætype of deviceÆ. Based on the experience of the author, it appears that risk management and life cycle approach to seals has not been adopted to the same extent as for other aspects of operations. Further, because of the number of disciplines and personnel involved that may influence various factors affecting seal integrity, the opportunity for oversight or unclear allocation of responsibility is considerable. While suppliers can provide explosion or design rated seals, this should only be a starting point for application of the product in a coal mine. Application is often considered by mine planning staff (taking into consideration mine environment parameters such as water, control of gas, spontaneous combustion risk, etc) in conjunction with the colliery ventilation officer, and then construction completed by contractors under supervision of operational staff. After construction, seals often are managed by operational personnel with input from the ventilation officer. Input of the geotechnical engineer into pillar design, roadway opening size, ground support specification and most stable seal location is also required. The need for a customised design approach for each seal site is proposed in order to take into account the many and variable factors that may influence a site so that improved seal performance reliability and predictability can be developed. A program of quantitative as well as qualitative monitoring of performance and triggers for rectification or maintenance action is required, and would provide support to the aforementioned proposal. Many mines rely on visual/audible inspection and periodic bag sampling as the primary means of assessment. Other significant factors such as seal material properties, rib degradation, convergence, floor heave, effects of water on both structural integrity of the seal as well as the air tightness of the seal do not generally receive the same level of attention. Based on the above observations, the author has compiled a reference checklist in regard to the above matters, including aspects of and approaches to mine and pillar design, geotechnical modelling and data collection, civil engineering design, site evaluation and practical options available.

Jan 1, 2005

By S Taylor, B Lumsden, G Long

Statistical metallurgical plant trials are becoming more widespread, as a valuable tool for increasing plant profitability. Generally, a single parameter like metal recovery varies under the trial condition while all other variables such as average metal feed grade or average metal concentrate grade are equal for the two test conditions during the period of the test. Metal recovery is usually the measured variable because concentrate grade is fixed by smelter terms, and plants operate to maximise recovery at the required concentrate grade. However, in all flotation plants there is a relationship between concentrate grade and metal recovery, and under the same conditions increasing one results in a decrease in the other. At MMGÆs Rosebery Mine the zinc concentrate produced is generally above smelter specifications, so zinc concentrate grade can vary during a test. During trialling of magnetic conditioning in the Rosebery zinc circuit, the difference in both zinc recovery and zinc concentrate grade were analysed. The analysis of changes in zinc grade and recovery during the trial raised some interesting questions about the relationship between concentrate grade and recovery. A paired statistical method was developed and tested to combine in each pair the change in concentrate grade and recovery in a single result that could be analysed by a paired t test. This method was found to be very sensitive to combined, varying changes in concentrate grade and/or metal recovery. It was also evaluated on plant test results from another flotation plant to verify its applicability in other plants. CITATION:Long, G, Taylor, S and Lumsden, B, 2012. Statistical plant trials - Efficiently combining concentrate grade and metal recovery results, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 355-362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By S J. Kim, S W. Kim, L Tomas da Rocha, S Jung

Al2O3 has been regarded as a harmful gangue component in iron ore, especially causing reduction degradation in industrial sintering of iron ore. The current study aimed to utilise low-grade iron ore containing high Al2O3 content in sintering process. In order to counteract the adverse effect of Al2O3 on reduction behaviour of iron ore sinter, mill-scale and calcined dolomite were chosen as FeO- and MgO-bearing materials. Firstly, mill-scale was added to high Al2O3 sinter and addition was optimised as 10 wt per cent, then calcined dolomite was added further. Magnetite and magnesio-ferrite were identified as the major phases in iron ore sinter when adding mill-scale and calcined dolomite. As the dosage of calcined dolomite increased beyond 4 wt per cent of in sinter mix, unreacted MgO particles were observed, which is ascribed to the limitation of MgO dissolution into magnetite matrix. Both mill-scale and calcined dolomite were effective in improving compressive load and Reduction Disintegration Index (RDI) of iron ore sinter although its reduction degree was highly decreased. The addition of both FeO and MgO-bearing materials to high Al2O3 sinter has a potential to improve the sinter quality, also contribute to the recycling of industrial by-product. However, the amount should be optimised in views of phase development and deterioration of reducibility.

Jun 19, 2024

By N S Melkoumian

While improvements in occupational health and safety (OHS) in the mining industry have decreased fatalities and accidents, little attention has been paid to the cultural confound of 'safety' in the increasingly multicultural mining industry. Occupational health and safety processes often contain assumptions of cultural understanding that may not be shared or understood by mining employees. There are potentially dangerous and costly implications of cultural difference in the mining environment. Some people have been enculturated with high levels of anxiety concerning catastrophe and uncertainty while others have a more laissez faire attitude to accidents and disaster. The level of cultural anxiety about uncertainty can be a major factor in the acceptance of OHS processes. OHS manuals based on a comprehensive set of rules and procedures may assume that the authority of 'rules' is shared by all employees regardless of a variety of cultural understandings when this may not be the case. Similarly, cross-cultural employees may not share a background or acceptance of expensive technological innovation and so resist/avoid the application of new safety equipment. Then too, OHS staff may not realise the significance of religious belief or personal responsibility on employees' attitudes to safety in the workplace environment. A lack of consideration of these cultural elements could have fatal and expensive results. This paper explores the impact of cultural difference in the understanding of OHS in the Mining Industry, presents a model to improve the understanding of the cultural confound in safety, improves analysis of OHS in practical multicultural situations, provides assistance for those involved in OHS training and may become a basis for developing OHS policy and procedure.

Dec 6, 2010

Improved roof control in high deformation tailgate environments has been achieved over the last decade through development of stiffer and increased capacity standing support products. æThe CanÆ is one such development, being a steel cylinder containing a weak cementitious fill, designed to essentially fold in upon itself whilst maintaining strength. A laboratory study to better define the relative load contributions of the steel cylinder and fill, the confining interaction between these components and most importantly, the potential impact of varying the steel and/or fill properties is described. This would enable the support engineer to ædial-upÆ the desired strength and stiffness properties and optimise the standing support design with respect to load capacity, stiffness, weight (handling) and cost. Design curves to optimise strength based on steel casing thickness, fill strength (confined and unconfined) and æCanÆ geometry were established. Scaled-down (one-third) samples were used in the test program and found to adequately reflect the loading behaviour of full-scale versions, thereby providing significantly greater scope for further product development at less expense compared with testing full-scale products.

Jan 1, 2005

By N Petropoulos and M J Thurley, E Righetti, M Wimmer

Fragmentation in sublevel caving (SLC) is vitally important. Both gravity flow and any downstream processes are affected. Reasonably coarse fragmentation may lead to larger draw bodies (isolated extraction zones) and hence potentially higher primary ore recovery and depressed/delayed waste rock inflow from above. Fewer flow disturbances are expected by mitigating oversize. In addition, it requires less boulder handling and reduces wear and possible hang-up problems in orepasses. To assess the present-day functionality of large-scale SLC, a multiyear, comprehensive measurement program was initiated. It covers the main elements for SLC, namely blast function, fragmentation and gravity flow. The present paper focuses on fragmentation measurements. An image acquisition system was used to document the drawpoint and the load-haul-dump (LHD) bucket for each mucking cycle. At the beginning, four buckets (about 70 t total) were sieved to validate the results of both 2D and 3D image analysis techniques. The fundamental and specific problems are discussed herein. At the moment, fragmentation of the SLC rings is evaluated using a quick rating system and a 2D fragment delineation software. The results enable a description of fragmentation and its variation during mucking but also – combined with the gravity flow measurements – conclusions on the fragmentation for different parts of the SLC ring. Possible influences on flow disturbances and ore recovery/dilution are investigated. The recent findings allow a better understanding of breakage and flow and support future process improvements.CITATION:Wimmer, M, Nordqvist, A, Righetti, E, Petropoulos, N and Thurley, M J, 2015. Analysis of rock fragmentation and its effect on gravity flow at the Kiruna sublevel caving mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 775–792 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Y Peng, B Guo

In gold processing plants, the water from the cyanidation stages is treated to detoxify cyanide species and this recycle water becomes the main part of the process water. Despite the low concentration of free and weak acid dissociable (WAD) cyanides in process water, the recoveries of gold and silver is still affected during flotation, especially when gold and silver are associated with iron sulfide minerals. This is a case at the Hidden Valley (HV) Mine. In this study, the effect of free and WAD cyanides on gold and silver recoveries by flotation from the HV Mine was considered.WAD cyanide (WAD CN) was prepared by mixing sodium cyanide and copper sulfate at a cyanide to copper ratio of 3:1 dosed at different cyanide concentrations. It was found that both free and WAD CN depressed gold and silver and particularly iron sulfides in flotation. The depressed gold and silver recoveries were closely associated with the depressed recovery of iron sulfide minerals, suggesting that free and WAD CN may not depress the flotation of liberated gold and silver minerals significantly. It was also found that 10 ppm free cyanide completely depressed the flotation of iron sulfide minerals and WAD CN depression is probably through the WAD dissociation to free cyanide species (mainly aqueous HCN) during the grinding process, resulting from a decrease in pH. Thermodynamic calculation showed that 5.5 ppm free cyanide was released in the end of grinding at an initial WAD CN concentration of 50 ppm. This research provides a guideline to counteract the negative effect of WAD CN in the flotation of gold and silver minerals.CITATION:Guo, B, Peng, Y and Espinosa-Gomez, R, 2013. The effect of weak acid dissociable cyanide on gold and silver flotation in Hidden Valley Mine, in Proceedings World Gold 2013 , pp 341-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

In this paper a quantitative deterministic risk modelling approach (Quadrim) is introduced. The mathematical framework and equations for quantifying uncertainty within and aggregating across value chain nodes from error propagation techniques is proposed and discussed. A case study and worked examples, based on a hypothetical mine are then presented. This illustrates how uncertainty from the mining and economic value chains can be handled in a typical net cash flow calculation, and how this can be translated to a risk model. It is then illustrated that current valuation techniques do not just result in an information gap for decision makers. Traditional approaches such as discounted cash flow (DCF) analysis and truck and shovel productivity analysis, which do not take into account uncertainty in input values, can result in potential bias in estimates such as net present value (NPV) or equipment hours

Sep 26, 2011

By A Horn

Mineral processing is characterised by a constant adaptation to changing raw materials and market conditions. It is the link between the mined raw material and a marketable product. As a lot of high-grade reserves are exploited, a steady deterioration of raw material quality can be observed. At the same time, the customer’s requirement for product purity and consistent quality increases.Over recent years beneficiation techniques for iron ore fines have become more important in order to achieve a maximised utilisation of ore resources and to produce competitive products according to international standards.Many high capacity iron ore beneficiation plants that target the production of fines focus on gravity separation processes using fluidised bed classifiers and spirals or wet high intensity magnetic separators as an alternative. This paper demonstrates the suitability of utilising the allflux® two-stage fluidised bed classifiers to treat iron ore particles up to 2 mm in size as well as showing how the high capacity gaustec® wet high intensity magnetic separation (WHIMS) technology offers several advantages compared to other WHIMS technology.The combination of the allflux® and gaustec® technologies offer the following benefits:The two-stage fluidised bed classification extracts a significant amount of concentrate from the feed. This in turn reduces the feed capacity required for the gaustec® WHIMS located downstream.The second classification stage produces a -0.5 + 0.1 mm product and a -0.1 mm product. The efficiency of the magnetic separation on these classifi ed products is high due to optimised settings for each size fraction.

Jul 11, 2011

By P Trout, B Macaulay

Ridgeway Gold Mine (RGM) is an underground sublevel caving (SLC) operation that is owned and managed by Newcrest Mining Limited (NML). Production drill and blast practices are critical to the success of the SLC method at RGM. SLC production ring precharging was introduced in November 2001 to enhance these practices and deliver safety, productivity and cost improvements. Current precharging practices require up to two rings to be loaded ahead of the ring to be blasted in each drawpoint. The explosive may be required to remain in the up-holes for periods of four weeks or more prior to blasting. During this æsleepÆ time it is subjected to repeated shock from the blasting ofadjacent rings and from rings in adjacent drawpoints. The project described in this paper was designed to gain an understanding of the factors affecting explosive performance in the precharging environment and to develop explosive products and operating practices that would meet RGMÆs requirements in terms ofsaf ety, reliability and blast outcomes. Several months oflaboratory and field testing were required to characterise the explosive and quantify the effect of post-loading blasting shock. These results were used to determine the most appropriate loading and sleep time criteria for RGMÆs precharging practices. In addition, the information is being used to guide the development of the next generation of emulsion explosives for use in underground precharging operations.

Jan 1, 2005