Search Documents

Geological Parameters Controlling the Improvement of Manufactured Sand Using Vertical Shaft Impact Crushers Instead of Cone Crushers Natural sand is a limited resource. In Sweden the total use of natural sand and gravel is around 20 million tonnes per year and the goal is to halve the use of this resource in the near future. Most of this natural sand is used for concrete production, so the consequence of this goal is that more and more concrete must be produced with manufactured sand. The bedrock of Sweden consists mainly of granites and gneisses, rock types mainly composed of various amounts of quartz, feldspar and mica. Manufactured sand from these materials generally contains rather flaky and elongated grains, and there are few types of granite that can be used as manufactured sand in concrete without increasing the amount of cement by eight to ten per cent. A Vertical Shaft Impact crusher (VSI) is commonly used to improve the shape of coarse aggregate particles. Research has shown that it is even possible to improve the shape in aggregate fractions less than 1 mm for some rock types. The aim of this project was to investigate which geological parameters control the improvement of manufactured sand when using VSI-crushers instead of the traditionally used cone crusher. In order to do this eight rock types of granitic composition were investigated. The selection of rock materials for the tests was based on grain size and mica content. A 4 - 8 mm fraction of each material was used for the tests. The characterisation of the shape of the material was performed using image analysis applied on microscopic images. The results showed that the VSI-crusher had improved the shape of all materials down to 0.036 mm, except for one rock sample. According to these results granites with low mica content and relatively high content of feldspars have the best prerequisites to produce manufactured sand for concrete with suitable geometric characteristics, and if these materials are crushed with a VSI crusher they almost show the same characteristics as natural sand.

Sep 13, 2010

By Woodhouse M, Andrews D, Drew G

The nickel deposits within the Honeymoon Well project area (26¦ 40'S, 120¦ 25'E), located 45 km south of Wiluna, occur in the northern part of the Agnew-Wiluna belt (Figure 1; Hill et at, 1990). The project area is covered by up to 50 m of transported material which greatly hampers both exploration and an understanding of the bedrock geology. Since 1990 intensive exploration has increased the resource from 10 Mt at one per cent Ni to 134 Mt at 0.76 per cent Ni in five deposits (0.4 per cent Ni cut-off, resources above 300 m depth, December 1994). This includes a massive sulphide resource of 2.5 Mt at 3.4 per cent Ni.

Jan 1, 1996

By S J. Clarke, C S. Walker

The South West Rail Link (SWRL) project involved construction of a rail line to service new residential areas in south-west Sydney. The 11 km rail line is conveyed through a short tunnel at shallow depth where it crosses beneath the eight lanes of the Hume Highway. The underpass location is one of the most heavily trafficked within Sydney’s motorway network.The New South Wales Roads and Maritime Services (Roads and Maritime), as the owner of the highway asset, had the responsibility of managing the risks to the highway and traffic associated with the tunnelling project from the pretender stage through to completion. This paper considers the primary risks and mitigation measures employed, including geotechnical investigation, and development of appropriate construction constraints and concept design of an extensive real-time survey system to monitor pavement deformation during the tunnel works.The geology comprises fresh Minchinbury Sandstone in the tunnel invert and side walls, and variably weathered Bringelly Shale in the haunch and crown. Few tunnels have been excavated in these rock types in Sydney, and there is little information relating to the in situ stresses and stress-relief deformations in these materials.During tunnel construction the monitoring data indicated unexpected surface heave of up to about 24 mm. A multiparametric back-analysis of the deformation data is presented, which provides information on the deformation mechanisms and key geotechnical parameters, including rock mass modulus and in situ stresses.The approaches and methodologies developed for the SWRL underpass were effective in maintaining the safe operation and traffic capacity of the highway throughout the construction period, and the analysis of the monitoring data provides a useful reference for similar future projects, or projects constructed in similar ground conditions.CITATION:Clarke, S J and Walker, C S, 2014. Deformation mechanisms of the South West Rail Link underpass beneath the Hume Highway, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 631–640 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Tailings management trade-off studies are done for all mining projects. There is wide variability in these studies as their approach, details and outcomes are determined by the experience and focus of the project team. While some of these approaches may consider the whole life cycle of the project others may focus only on capital and operating costs and direct environmental impacts. A complete life cycle approach is not standard practice. This paper describes an approach to implementation of formalised life cycle assessment (LCA) following ISO 14044 to tailings management trade-off studies. The paper describes the implementation of the methodological framework for the LCA, ie goal and scope definition, life cycle inventory analysis, life cycle impact assessment and life cycle interpretation. This standardised approach to implementing tailings management trade-off studies following the LCA approach will contribute to the state-of-the-practice in sustainable mine development.

Jan 1, 2009

Pressure Oxidation of Sulfide Gold-Bearing Concentrates with Double Refractoriness

Sep 13, 2010

By H J. Stedman

A Transient Electromagnetic (TEM) geophysical survey was trialled in Bowen Basin Permian coal measures overprinted by Cretaceous intrusion. The trial’s intention was to compare whether TEM could assess residual coal more accurately and economically than drilling.TEM results were promising but had limitations. TEM did not compare to drilling for defining coal thickness or relative level definition. However, TEM resolved conductive anomalies laterally; providing a qualitative picture of remnant coal.Three material types and associated conductivities occur within the trial area: overburden (sandstone/siltstone), intrusive sills and heat affected coal.Ground conductivity was analysed by measuring decay of residual current within the TEM loop. Fast decay related to resistive overburden and intrusion, attenuated decay related to conductive coal.Generally speaking, carbon content governs coal resistivity where good quality, low ash, bright coal is more resistive relative to dull, high ash coal. Though in the trial area, relative to intrusion and overburden, coal was found to be the most conductive of the three materials.By modelling conductive anomalies, a general picture emerged of remnant coal regions. Subsequent highwall exposure reconciled with conductive TEM anomalies.CITATION:Stedman, H J, 2017. Findings from a transient electromagnetic trial for heat-affected coal, in Proceedings Tenth International Mining Geology Conference 2017, pp 233–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By K Saito, M Hasegawa

In steelmaking processes, it is known that P2O5 in dephosphorisation slags often exists in solid solutions between Ca2SiO4 and Ca3P2O8, <C2S-C3P>SS, and thus the solid solutions play an important role in the dephosphorisation reaction. Hence, the knowledge of thermochemical properties, ie phase relations and activities of components, in slags containing <C2S-C3P>SS are necessary for the effective removal of phosphorus from hot metal. In this study, the P2O5 activities in <C2S-C3P>SS were measured through the gas equilibrium method. In the present experiment, oxide samples were equilibrated with Cu-P liquid alloys at 1573 K under a stream of Ar + H2 + H2O or Ar + H2 + CO2 gas mixture in which oxygen potential was fixed and then equilibrium phosphorus concentrations in the Cu-P alloys, [mass%P]Cu, were analysed with ICP-OES.

Aug 21, 2024

A New Online Detection Method for Arsenic Minerals in Process Streams

Sep 13, 2010

By A J. Daniels

Macraes Mine is a large-scale open-cut and underground gold mine located in Central Otago, on the South Island of New Zealand. This paper presents the role of geological mapping in the grade control process at Macraes Open Pit as a case study, and demonstrates how systematic geological mapping can add significant value to the mining cycle. Geological mapping has proved to be a valuable foundation for orebody interpretation and analysis.Practical applications and lessons learnt are summarised, including predictive control of the orebody, improvement of geotechnical modelling, and identification of further exploration targets.

Aug 22, 2011

By G A. Wellwood

What do all iron ore mines have in common? Perfect production days! Yes, those harmonious 24-hour periods when the stars align and the daily output number rockets past the long-term average to hit new heights. While perfect days are always welcome, the focusing question iswas that just a ‘flash in the pan’ (due to a special cause) or an indication of the process’s capability (with clues to the common causes) which, if addressed, could make every day perfect? In the context of today’s operating environment, with the need to maximise productivity at minimum cost, it’s an important question.Investigations reveal that the throughput difference between a perfect production day and the average is often in the order of 40 per cent, and that bulk solids handling (BSH) system deficiencies are the largest (&gt;50 per cent) class of lost opportunity. Root causes for underperformance of elements in BSH systems can often be traced back to the detailed design and even study-stage oversights. Essentially baked into the fabricated plant, operations are effectively forced to accept them at the point of practical completion and then deal with the consequences for the life of the mine. Subsequent normalisation of these defects in the planning process reduces visibility and hence the impetus for long-term solutions in favour of lower targets and quick fixes to keep the show on the road. On an industry wide basis the design processes and assumptions responsible for BSH system underperformance become enshrined as common practice and hence repeated across sites and organisations.In addition to making the case for action, practical steps that can be taken to help realise the significant productivity prize and avoid the problems in first place are provided.CITATION:Wellwood, G A, 2017. One perfect (production) day – a bulk solids handling perspective, in Proceedings Iron Ore 2017, pp 443–452 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

A number of mineral deposits occur in close proximity to the Pacific plate fronts. Among these deposits are gold-silver and the base metal sulphide deposits of copper, zinc and lead. Gold deposits that commonly occur in these areas are of hydrothermal origin. Of these the epithermal deposits have attracted the attention of the exploration geologists as well as the metallurgists. One vital aspect of the activity of the geologists is the development of models for epithermal gold mineralisation in the Pacific Rim. These models can also be used by metallurgists for predicting gold extraction processes. This paper reviews the mineralogy, fineness and the host minerals of gold and examines the data in the light of gold mineralisation in the southwest Pacific Rim. The gold mineralisation models proposed for the Pacific Rim have been used to predict gold extraction processes suitable for the various mineralisation types. Discussed also are the mineralisation and treatment processes of some selected epithermal gold deposits and gold-rich porphyry copper deposits in Indonesia, Papua New Guinea, Solomon Islands, Fiji and New Zealand.

Jan 1, 1999

By J Pan, C M. Tang, D Q. Zhu, C C. Yang, S W. Li, Z Q. Guo

The short process of electric furnace steelmaking with direct reduction iron (DRI) as raw material is an important process for smelting high-quality and special steels. In order to prepare high-quality DRI, the pellets with basicity of natural basicity and 0.4 were prepared from magnetite concentrate (MR=0.09, MR=0.4) and hematite concentrate (HR=0.02, HR=0.4). Based on the HYL method, the gas-based direct reduction experiments were conducted under the condition of rich hydrogen (H2/CO = 2.6). The reduction index (RI), reduction swelling (RSI), cold compressive strength (CCS), and phase changes of the pellets were systematically studied. The results show that the RI of four kinds of pellets is greater than four in the temperature range of 800~950°C. For the magnetite pellets, at a fixed reduction temperature, the RSI increases and then gradually decreases, reaching a peak between 50 per cent and 80 per cent. Moreover, the RSI enhances with the increase of the reduction temperature. In general, the RI, RSI, and reduced CCS of the MR=0.09 pellets are better than those of the MR=0.4 pellets. For the hematite pellets, the maximum RSI decreases from 23 per cent to 17 per cent during hydrogen-rich reduction, while the compressive strength increases from 500 to 1070 Nꞏpellet-1. The main reason is that the glass phase generated by the increase of basicity adheres to the surface of hematite grains, hindering the contact between reducing gas and particles. As a result, the apparent activation energy is reduced, which is not conducive to the reduction process. In addition, the glassy phase attached to the hematite reduces the migration rate of Fe2+/Fe3+, resulting in a difference in the reduction expansion rate of hematite in the inner and outer layers of the pellet. Thus, concentric cracks are formed inside the pellets, the RSI increases and reduced CCS decreases.

Sep 18, 2023

We are moving into an era where we experience the consequences of the skills crisis û namely many resource models have been generated by inexperienced people under pressure to deliver high quality resource estimates in unsupported environments, often without technical mentors. These resource models form the basis of our decision to pursue actual mining. This begs the question: how valid are the resource models that form the basis of our mining decisions? This paper presents various model validation tools such as comparison of input and output statistics, swath plots, sectional or bench comparisons between drill holes and models as well as a variety of other approaches. Each model validation tool currently used in industry is examined:how the tool generates results,what assumptions exist,what constitutes a pass/fail in the test, and what interpretations to consider when using the validation tool. Each validation toolÆs suitability and the inherent flaws in the underlying assumptions are also discussed. These are supported with examples of good versus bad validations. Our principles based reporting codes provide flexibility in how models are generated and what approaches and/or parameters are used to generate resource estimates. This flexibility works well when used by experienced practitioners. However, our reporting codes assume a level of experience not always available in the current skills crisis. This paper seeks to provide minimum model validation prerequisites for model acceptance and suitability, regardless of the resource analystÆs experience. As we move forward, our immediate challenge is to ensure our baseline resource models are material, transparent and competent.

Jan 1, 2009

By V M. Silva, P A. A Martins, V O. Matthew, A L. S Fonseca, E B. Cunha, A J. D Ferrari, E M. S Silva, A C. Silva, D R. T Vilela

The Anglo American phosphate mine is located in the Brazilian state of Goi&#225;s and possesses one of Brazil’s most important phosphate rock deposits, with the site being the country’s second largest producer of phosphate rock concentrate. Despite the site having been in operation since 1979, the mining team only started using explosives in 2004 when rocks with greater hardness started to appear in the mine’s geological profile. Rock excavation was previously performed mechanically. Until 2013, only rocks with high hardness were blasted, this following the standard drilling grid that was defined in 2004 without any changes in the blast parameters. The aim of this paper is to show how fragmentation optimisation has yielded positive results at all stages of the production chain, from the mine to the mill passing through an impact hammer crusher, a rod mill and ball mill, operating in close circuit with hydrocyclones.While incorporating the mine to mill holistic approach during the operational integration, the focus was on defining the blasting domains and respective optimal fragmentation and measuring the benefits of blasting in terms of reduction in energy and grinding media consumed in the comminution processes. In the first stage, the blasting team made changes to the blasting parameters and assessed the effects of these changes on fragmentation using computer software and on-site measurements. This generated a database that made it possible to divide the mine into blasting domains. For the second stage, teams from the plant, geology, mine planning and operation departments jointly made comparisons between the performance when processing stockpiles, which only included high hardness blasted ore (20–30 per cent of blasted ore). Changing the drilling grid’s size from 3.0 m &#215; 3.8 m to 2.0 m &#215; 2.6 m for high hardness rock with the presence of silicates resulted in a 40 per cent reduction in the P80 for the blasted material (from 459 to 278 mm), while changing the grid from 3.0 m &#215; 3.8 m to 2.6 m &#215; 3.2 m for high hardness rock without the presence of silicates generated a reduction of 25 per cent (from 270 to 204 mm). There were gains observed from the measurements at the mineral processing plant in terms of specific energy spent on comminution and on the consumption of grinding bodies in the rod mill. There was a measured reduction of circulating load during secondary grinding and a reduction in slime generation.CITATION:Silva, A C, Martins, P A A, Silva, E M S, Fonseca, A L S, Ferrari, A J D, Cunha, E B, Silva, V M, Matthew, V O and Vilela, D R T, 2015. Fragmentation optimisation – adopting mine to mill for reducing costs and increasing productivity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S C. Dominy

For any gold deposit-based geometallurgical study, the collection and processing of representative samples for gold grade and recovery tests is critical. Sampling protocols should be designed to suit the style of orebody in question. The proportion and size of gold particles has a direct impact on the effectiveness of sampling protocols and metallurgical recovery processes employed. Studies focussing on ore mineralogy and gold particle deportment, size and distribution are required. Key issues are the presence of gold particle clustering (important for sampling optimisation) and proportion of coarse versus fine to refractory gold. X-ray computed tomography (CT) is a radiographic technique that produces high-resolution 3D computerised models of objects based on density distribution. The ‘virtual’ specimens are made up of voxels, the 3D equivalent of pixels each assigned a grey value based on X-ray absorption. This paper presents the results of recent research on the imaging of in situ gold particles in a coarse gold-bearing ore. The technique shows promise as a rapid non-destructive method for preliminary characterisation to facilitate more detailed studies. Early and rapid gold particle determination enables sampling protocol optimisation and metallurgical recovery parameters to be defined prior to detailed feasibility studies

Sep 5, 2011

During a mineral exploration program in an environmentally sensitive area nearMount Painter in South Australia, a helicopter was used to position, construct and service drilling rigs in order to avoid the need to create new access tracks. The drilling program was designed to optimise the advantages of natural landforms in order to minimise the environmental impact of site construction and drilling activities. This minimisation of land disturbance reduced the required amount of rehabilitation measures to the extent where all impacts of the helicopter-supported programme had disappeared within 12 months of completion of work.

Jan 1, 1995

Mother Nature controls, technical professionals model and miners decide. Decisions to explore, mine and mill. Mine decisions, mine design, planning and scheduling are subject to the quality of models û geological models, geotechnical models, resource models, density models. The closer these models are to reality, the more accurate the predicted outcome. So why is it we delegate the modelling tasks to the most junior and least experienced people? If we insist on this, we need to support them û to provide them with æexperience acceleratorsÆ. Technical mentoring is the most effective way to provide the right information at the right time. When this information (read skills) is supplied at the right time we can inject experience into the quality of our modelling and into our decision- making processes. The objective of this paper is to share those behaviours and manners that foster relationships and create frameworks for skills and experience transfer. Central to this is an understanding of how adults learn, an understanding of the basic rules of mentoring etiquette, and the three keys to building meaningful mentoring relationships. An understanding of adult learning processes and styles provides a structure within which a mentor can understand the learnerÆs perspective. Understanding the world from the learnerÆs point is critical to selecting the right language to engage, teach and transfer skills. Basic rules of mentoring etiquette like timeliness, respect and trust need to be brought into the consciousness so they can be agreed on and monitored to prevent conflicts in cultural and generational norms between the mentor and the learner.Meaningful relationships hinge on the three behaviours: truly listening, rather than just hearing; understanding the technical issues within the WIIFM (whatÆs in it for me?) question; and facilitative behaviour. Stronger and more meaningful technical mentoring relationships within our industry will bridge the generational gap and ensure we can capture and capitalise on the wealth of grey hair experience and develop an informed group of young decision-makers.

Jan 1, 2006

By K L. Brown

In the Waiotapu geothermal area only Champagne Pool, 109 ng/L, and Waiotapu Geyser, 7.6 ng/L, have dissolved Au concentrations greater than 5 ng/L and most springs have concentrations less than 2 ng/L. When Au concentration data are combined with other physico-chemical data from each spring including; pH, reduced sulphur concentration and temperature, the degree of Au saturation can be calculated. All samples sites except Champagne Pool, Waiotapu Geyser and the Artists Palette are under-saturated with respect to Au(s) by 1 to 3 orders of magnitude. This indicates that adsorption or co-precipitation or both are important processes depositing Au beneath hot springs. Deposition of Au by adsorption or co-precipitation beneath hot springs implies that dissolved Au may not have to reach saturation concentrations for ore to deposit. This interpretation is supported by the presence of substantial Au as sub-microscopic components within sulphide minerals in ore deposits and indicates depositional efficiency beyond that possible through precipitation of Au(s).

Jan 1, 2004

By S M. Stewart

Building and Maintaining Community Relationships &nbsp; In mining terms, the town of Waihi is distinctive with the Martha mine situated right in the heart of the town. MarthaÆs central location and other mining activity nearby means there is an increased community focus on the happenings at the mine and the effects and impacts of mining. While WaihiÆs proximity to the mine is unique, all mines have a community context that they operate within. &nbsp; Issues of proximity simply heighten awareness and emphasise the need for building and maintaining good community relationships. In the three years we have been working alongside the Waihi community, we have worked together with concerned and supportive residents, representatives of Newmont Waihi Gold and representatives of Hauraki District Council, to develop a collaborative framework for addressing the economic, social, environmental, cultural and spiritual wellbeing of the people of Waihi. This could not have occurred without the genuine commitment of all participants. &nbsp; This collaborative focus has resulted in some tangible progress in Waihi which, in part, stems from people taking an interest in the town because the town is taking an interest in itself. As we have worked and learned within the process of building and maintaining a collaborative and sustainable community environment, we have tried to adhere to a philosophy and a set of basic principles. We believe that this approach, combined with a teachable skill set, helped to create the opportunity to develop a truly collaborative community environment which continues to grow. Our paper will describe this philosophy, these principles and the skill set that we have applied. &nbsp; The application of the process in Waihi has resulted in a series of outcomes unique to Waihi. These outcomes include formation of the Waihi Community Vision committee, the Vision Waihi Trust and the subgroups set up to further the interests of particular groups, for the collective benefit of all the community. &nbsp; Based on our experience of other situations, and on the way the Waihi process has developed, we believe that the identified principles and skills can be transported and used in other cultures and contexts. While the resultant outcomes may differ, the underlying principles will still apply. Progress will come from creating a sustainable environment within which the community (including residents, industry and regulatory authority) can determine its own internal relationships and the vibrant growing sense it has of itself.

Jan 1, 2006

With the continued implementation of stricter limitations on the discharge of excess process water from all existing and future mining and metallurgical operations, the design and operation of the entire process water circuit must form an integral part of any total operational package. It is far better to æanticipate and circumvent the problemÆ rather than be forced into an expensive remediation program after the event. By far the greatest problem relates to the treatment and disposal of what is generically known as acid drainage. In simple terms, an acidic metal sulfate solution is generated by a series of chemical and biological reactions as soon as most sulfide minerals are exposed to air and water. Treatment of this solution by one or more of a wide range of chemical and physical options can involve substantial capital and operating costs, although there are recent processing options that yield saleable by-products, thereby reducing the financial liability of what is effectively a waste stream. This presentation provides an overview of the Australian situation compared with the rest of the world and outlines the basic features of a number of the more advanced passive and active acid drainage options.

Jan 1, 2004