Search Documents

By H. J. de Haan, L. Schenk

Scope for Thermal Recovery in Shell's Heavy Oil Fields in Venezuela The main heavy oil reservoirs on the East coast of Lake Maracaibo (Fig. I), known as "Bolivar Coast", initially contained some 20 billion bbl of oil in place with gravities in the range of 10 to 15° API. The current total production rate is about 400,000 B/D. Since the recovery to date is on an average only 12.5 percent of the initial oil in place, these fields offer a vast potential for secondary recovery methods. The reservoirs are characterized by moderate depth (generally 1,000 to 3,000 ft; maximum 5,000 ft), good formation properties such as net oil sand thickness (50 to 300 ft), high porosity (30 to 40 percent) permeability (1 to 3 darcies) and oil saturation (initially about 80 percent) and high oil viscosity (100 to 10,000 cp in situ), all of which are favorable for the application of thermal recovery processes. Since 1957, steam drive, steam "soak" and underground combustion have been tested or are being tested in this area.1-3 This paper deals with a major steam drive test in the Tia Juana field. The test was commenced in Sept., 1961, on the basis of encouraging results of laboratory experiments and pilot field tests, which will be discussed briefly. Early Laboratory Investigation of the Steam Drive Process In 1956 a series of model experiments was carried out in the Koninklijke/Shell Laboratorium, Amster- dam, to investigate the displacement of heavy oil by steam.' The prototype studied was a horizontal, un-consolidated heavy oil reservoir, subjected to a linear steam drive. The model, representing a slab from this reservoir along the main flow direction, consisted of a steel tube filled with oil-saturated sand, provided with layers of rock at the top and bottom to simulate conductive heat losses to cap and base rock. Lateral heat losses, perpendicular to the main flow direction, were minimized by insulating the sides of the model. Heat flow and viscosity and gravity forces were scaled by taking the steam injection rate and sand permeability inversely proportional to the geometric reduction factor of the model, and using materials (oil, steam, cap rock, etc.) identical with those of the prototype. The main feature of the process was a frontal displacement mechanism that was observed within wide ranges of injection pressure and rate, oil viscosity, initial oil saturation and sand permeability. The high stability of this front can be attributed to the high volumetric steam flow rates, combined with the reduction in oil viscosity. High recoveries were obtained due to the low residual oil saturation of about 15 percent in the zone swept by steam. The latter value pertains to the specific test conditions (heavy oil, uncon-solidated sand) and may be lower for light oil, due to the effects of steam distillation. The applicability of this experimental approach is limited, as it does not take into account the fact that

Jan 1, 1970

By T. Lane Carter

(Canal Zone Meeting , October , 1910.) INTRODUCTION. IT is a curious fact that while in our Transactions there are papers dealing with mining-districts in all parts of the world, in Europe, Asia, Africa, and Australia, there is not one which describes the mining possibilities of Nicaragua; our near neighbor. To be most interested in distant objects, like the moon, .and to neglect what lies at our feet, appears to be a trait of human nature. The neglect of Nicaragua is not confined to the American Institute of Mining Engineers. In no other transactions am I :able to find papers dealing with mining in Nicaragua, some parts of which are as much in need of discovery and research as the North Pole.. I hope this paper will be the precursor of many others to be printed in our Transactions, dealing not only with the mining possibilities of Nicaragua, but with the whole of Central America, where there are vast areas awaiting skill and capital for their development. Much of this capital and skill should come from the United States in the future, although it is probable that European capitalists, when they appreciate fully the possibilities, will investigate more and more the mining-resources of Nicaragua and other Central American republics. Fig. 1 is a sketch-map of Nicaragua showing the principal mining-districts. II. HISTORY. Mining in Nicaragua did not begin yesterday. It was commenced by civilized man when the Spanish conquerors penetrated into the interior and forced the natives to procure the precious metal for them. It is strange that the Spaniards did not find more gold, and work on a scale as extensive as in Colombia and other parts of South America. Probably in Nicaragua the Indians covered up most of the rich prospects

Dec 1, 1910

Jan 1, 1969

By Gerald Greene

Tan various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulfur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1) states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As.

Jan 1, 1935

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

By J. R. Lucas, R. L. Frantz

Mine sealing programs for the alleviation of acid mine drainage were begun by the Federal Government in the '30's. As part of an acid mine research project to The Ohio State University, a field test was undertaken to determine the effectiveness of mine seals for reducing mine acid. Details of the tests made at the McDaniels mine show the feasibility of air-sealing and flooding an acid-producing drift coal mine. Work by the University continues. The Federal Government undertook in the early thirties an extensive mine sealing program for the alleviation of acid mine drainage. In the states of West Virginia, Ohio, and Pennsylvania many general summaries have been made on this program but no critical evaluation with supporting data has been found on the effectiveness of mine seals for reducing mine acid. Because of this it was decided to undertake a field testing program as part of an acid mine research project of the Engineering Experiment Station, The Ohio State University. The objective of this phase of the project was to develop and install a field research laboratory for acid mine drainage studies. Specifications for such a mine laboratory were developed and resulted from the following considerations: 1) Size and preservation—the test mine shou1d be of limited size to permit frequent and detailed examinations; it should be in a reasonably sound condition to permit safe entry. 2) Isolation—the mine should be physically separated from all other mines. 3) Openings—a minimum number would be desirable to reduce the sealing problem. 4) Structure—the mine especially near the openings should be structurally sound. 5) Acid production—the mine should be producing significant quantities of acid. After considerable searching, the McDaniels mine was selected in the Hocking coal field in Vinton County just above Lake Hope State Park in southeastern Ohio. The small drift mine in the middle Kittaning coal consisted of two small rooms with one mine opening about 6 ft above a seasonal stream bed. Before it was finally decided to seal the mine, a short study was made of the acid drainage over several months. Fig. 1 shows a plot of acidity (milligrams per liter), flow (gallons per minute), and acid production (pounds per day) vs time over the sampling period. Because the coal was overlain with a porous sandstone, the mine drainage was consistent the year around even though the mine was

Jan 1, 1961

By L. Adler

Longwall caving, one of the most economical and attractive mining methods, is yet one of the most difficult and hazardous.1 This dualism is inherent in a method which manipulates the mine supports themselves to aid in excavation. The difficulty is further compounded by the lack of an analytical method to predict and control results. This paper is intended to meet this need by providing a first approximation to the mechanics involved. The analysis will be limited to materials which are linear-elastic, homogeneous and isotropic. The rock structure is assumed to consist of beds of uniform thickness with no interbed bonding.2 Consequently, the mine roof can be likened to a beam, in which the action characteristic of longwall caving is the controlled deflection of the barrier supports. This deflection causes load to be intentionally transferred from these barrier props to the working face.3 Two of the requirements of this method, shared in common with other mining methods, are the provision of (1) adequate and (2) safe working space. The third requirement is the one characteristic of longwall caving and is somewhat in conflict with the second; (3) the development of near-failure static loads at the face. Requirement (1) is handled by spacing the barrier props sufficiently far from the working face for efficient operation. Requirement (2) limits the static stresses in the structure to predetermined allowable values. This means that it is not desirable to induce a maximum load on the working face as requirement (3) may imply. Such a condition could produce collapse in the whole structure. It is the purpose of the undercut to limit the depth, and thereby control the failure of the face. Therefore, requirement (3) really means the development of an optimum, not maximum, load which, in conjunction with undercutting, produces failure at the working face, with minimum powder consumption. Stress analysis requires an exact delineation of the structure and loads. The structure will be defined as the immediate roof and its supports. Since the roof is severed at the caving line, the supports reduce to the barrier props and the working face, as shown in Fig. 1. The mechanics of failure within the working face itself are complex and beyond the scope of this study, since the face represents a typical mine invert structure.4 However, this lack can be made good by the judicious collection of field data. The primary load on the structure is its own weight or body load which can be considered uniformly distributed over its upper surface. Additional loading occurs due to interference of overbeds with the structure. Wherever this occurs, the effect can be approximated by a load uniformly distributed on the upper surface of the structure.5 When this interference is intermittent, as with a much thicker overbed, the elastic curve for the overbed is superimposed on that for the structure and the extent of interference noted, as Fig. 2 shows. However, for simplicity, this study will ignore such intermittent loads without impairing the generality of approach. Consequently, the free-body diagram is that of a uniformly loaded cantilever beam with an inter-mediate support, as shown in Fig. 3. For convenience of analysis, the diagram will be divided just to the

Jan 1, 1961

By B. Wilshire, P. W. Davis

It has been shown that grain-boundary migration during high-temperature creep can reduce or even prevent the formation of intercrystalline voids, giving a considerable increase in ductility.' A similar observation has been made in a recent investigation of the creep properties of various grades of nickel and nickel alloys. The results can be illustrated by the observations made on: a) Pure vacuum-cast nickel (99.993 pct Ni) b) Impure vacuum-cast nickel (99.97 pct Ni) c) Pure nickel containing internal voids (produced by a process of intering). d) A substitutional solid solution alloy of pure nickel containing 1.16 pct Sn. All the materials were given a high-temperature anneal (>850°C) to produce a stable grain size of 7 to 10 grains per linear mm. The apparatus and techniques used to obtain the present results have been described elsewhere.' In this series, grain growth was observed only in the highest-purity, vacuum-cast metal. Thus we may consider that in the other materials grain-boundary migration was prevented by either preexisting voids or solute atoms. The effect of migration on the creep ductility of the above materials can be seen from Fig. 1, which

Jan 1, 1962

By Kefton H. Teague

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included.

Jan 1, 1950

By John Chipman, Peter J. Koros

The distribution of copper between liquid silver and liquid iron, Fe-C, and Fe-C-Si alloys was studied at 1600°C. From the data and the activity of copper in silver obtained from the phase diagrams, the activity coefficients of copper in iron up to 3 atomic pct are log y, = 0.90 — 2.4 N, and y": = 8.0. The effect of carbon up to saturation is expressed as log y = 1.8 Ni. The effect of silicon up to 11 atomic pct is insignificant. SLOWLY rising copper content of steel being produced is focusing attention on the lack of information on the behavior of copper in liquid steel. Chou' measured the activity coefficient of copper in liquid iron through its distribution between liquid silver and iron. He obtained a value of 9.12 at infinite dilution. Chipman' calculated the activity coefficient of copper in liquid iron at 1600°C from the phase diagram and obtained a value of 12. Ameiln and Pfeiffer- investigated the possibility of removing copper from liquid steel through the use of lead, silver, and bismuth as solvents. They also calculated that the activity coefficient of copper in liquid iron would be increased five or sixfold by addition of 4 pct C. Langenberg and Lindsay' are investigating the effectiveness of lead and sodium sulfide in removing copper from liquid iron. The experimental method was similar to that used by Chou' and Chipman and Floridis." Silver, copper, and iron were melted together, the copper distributing itself between the two layers so that at equilibrium a,.,, (in Ag) - a,.,, (inFe) and N,.,, (in Ag) yc,, (inFe) (in Ag). [21 N,.,, (inFe) Thus, from the concentration of copper in each layer and the activity coefficient of copper in liquid silver, the activity coefficient of copper in liquid iron can be calculated. The effect of an alloying element such as carbon on the activity coefficient of copper can also be determined from its effect on the distribution, provided the new element is essentially insoluble in silver. The one serious limitation of this method is the increasing mutual solubility of silver and iron in the presence of a third component. The mutual solubilities of pure iron and silver are negligible, but increase with increasing copper concentration beyond the range investigated. Ag-Cu System—The activity coefficient of copper in silver at 1600°C had to be estimated, since direct experimental data are not available. Kawakami" measured the heat of mixing of Ag-Cu alloys at 1200°C by a calorimetric technique. Scheil' calculated the heat of mixing in this system by use of the phase diagram, assuming that the solution is random and that the heat of mixing is independent of temperature. The terminal solid solution may be assumed to obey Raoult's law within the requirements

Jan 1, 1957

By Harold Price

ONE year ago, that is in January, 1923, there had not been constructed a single oil-storage tank of 55,000-bbl. or more capacity with a completely electric welded roof and bottom. Today, there are at least fifty 80,000-bbl. storage tanks completed, or nearing completion, on which both the roofs and the bottoms are electric welded. It is the purpose of this paper to describe, in a general way, the construction of these FIG. 1.-ELECTRIC-WELDED SEAMS AND RIVETS OF BOTTOM IN 55,000-BBL. TANK AT EL DORADO, KANS., SHOWING ALSO PATCH PLATE WELDED TO BOTTOM. welded roofs and bottoms, and to give their advantages over riveted construction. All of the following data and conclusions were obtained from observations made during the welding of tanks by the Welding Engineering Co. at Texas City, Tex., and Tonkawa and Burbank, Okla. As far as can be determined, the first electric welding on large tankage was completed in May, 1922. At that time the Empire Companies of Bartlesville, Okla., discovered a badly leaking bottom in a 55,000-bbl. tank at El Dorado, Kans. They had considered concreting this bottom, but because of the much smaller cost, decided to try electric welding; so a- contract was given the Welding Engineering Co. of Bartlesville, Okla. In this instance, no new sheets were added, the bottom being repaired by electric welding of all seams and rivets, Fig. 1. In some places where the original rivets were missing, the holes were filled by welding; patch plates were also added at certain badly worn spots. This tank has since been in service over a year and half, but no other

Jan 6, 1924

By G. M. Schwartz

THERE has been considerable controversy regarding the structure and mineral constituents produced when iron ore is sintered. This investigation was undertaken in order to establish the fundamental reactions that take place in the sintering process by determining the nature of the resulting minerals. The writer's immediate interest in the subject arose mainly from the request of E. W. Davis for information based on a microscopic study of sinter submitted by him in May, 1926. In the author's preliminary work, samples of iron-ore sinter were secured from the Minnesota School of Mines Experiment Station and from commercial plants. These were polished by the usual methods for polishing opaque ores. In order to study these surfaces satisfactorily, it is necessary to magnify them rather highly, a range from 100 to 1000 dia. being used. For the higher magnifications oil-immersion lenses and an intense source of light are necessary. After the preliminary study had shown the problems involved, a series of small samples were sintered under carefully controlled conditions and with analyzed materials. Variations in the relative amounts of ore, coal and water were made in order to study the effect of each constituent. The attempt has been to arrive at a clearer understanding of the sintering process and the reactions involved without reference to any preconceived notion as to sinter. It is clear that the study of polished surfaces has yielded results not possible with thin sections alone. The thin sections made in this work were found unsatisfactory at magnification greater than 75, whereas magnifications of 1000 were easily studied with reflected light on carefully polished surfaces. A rather complete statement of observed facts is made so that the reader may form his own conclusions. The writer's interpretations are suggested.

Jan 1, 1929

By P. K. Guerrero, N. Arbiter

The correlation of power consumed by a tumbling mill with the dimensions, speed, and load has been attempted by three principal methods. One of these, the torque formula, has been reviewed critically elsewhere.' This approach, while analytical, disregards the individual motion and speed of the tumbling bodies and assumes that the gross geometry of the entire load is sufficient to establish the power requirement. A more general approach, using dimensional analysis, has been applied in this laboratory by the present authors1'1, and more recently by Rose.3 This disregards the internal conditions within the mill entirely and in effect is an empirical procedure for correlating data. Finally, the complete analysis of tumbling mill dynamics as first made by Davis' attempts to develop the power requirement from individual ball and rod paths and velocities. Although Davis' result is applicable only at a single speed for a given size and load it could be useful, since his optimum speed is at the upper limits of conventional tumbling mill practice. Where power values predicted by the Davis equation were compared with actual mill requirements, they were found too low for small mills and much too high for the largest mills. This suggested that the agreement with actual intermediate range requirements might be fortuitous, and the development of the equation was examined critically. The probable source of error was found to lie in an erroneous assumption made by Davis in converting the energy of ball or rod motion to power. With the same approach, but with different assumptions, a modified equation has been obtained which predicts results that are usually consistently high. This is to be expected, since it is assumed that there is no slip between load and shell and no interference among tumbling bodies. Both these effects should account for the difference. Development of Equation: When a cylindrical shell charged with a substantial weight of rods or balls is slowly rotated about a horizontal axis, the load surface first assumes an inclination that gradually increases to a maximum. Continued rotation results in failure within the load, characterized by a sliding of the top layers down the slope and a reduction in the angle of inclination. Further rotation again increases the angle, and the cycle repeats. If the speed is increased, there is continuous load failure and build-up and a continuous stream of rods or balls descends over the upcoming mass, which moves in circular arcs. At higher speeds the up-

Jan 1, 1961

By Paul Billingsley

THE purpose of this paper is a comparison, based on genesis, of the ore deposits associated with the igneous rocks of the central Montana Rockies. Considered separately, without attention to their origin, the orebodies appear to be distributed haphazard, with no fundamental laws controlling their position and character. It is believed, however, that if all the factors be weighed, this apparent confusion will to a large degree disappear. The, first essential to such a comparison is detailed knowledge of the individual mines, as to their geographic position (see Fig. 1), their mineralogical character, and in particular the derivation of their ores.1 The authors of this paper have pursued such an investigation for the past 6 years, and have accumulated a mass of evidence that enables a preliminary correlation to be attempted. It appears that the majority of ore deposits are genetically related to one or another of the igneous

Jan 4, 1917

By J. D. Rice, S. C. Pitzer, C. E. Thomas

Interpretation of pressure build-up data obtained in the conventional manner has often been difficult because of the deviation from theoretical behavior. Major causes of this deviation have been attributed to damage and afterflow, and to fluid redistribution in the wellbore which, in extreme cases, can result in a pressure hump in the early portion of the build-up curve. Theoretical investigations show that bottom-hole pressure is definitely influenced by phase redistribution in the tubing column during surface shut-in tests, and that the magnitude of the effect is sensitive to the producing gas-oil ratio and stabilized rate of flow in the well. For field experiments a wire-line tubing packer, which can be run in the tubing against a stabilized flow rate, was developed for bottom-hole shut-in tests. By use of this bottom-hole .shut-in method, pressure humps previously observed in surface shut-in tests were completely eliminated and the effects of afterflow minimized. Analog and digital computer studies have been made to obtain theoretical curves for comparison with field curves, and remarkable agreement between the results of bottom-hole shut-in tests and theoretical curves has been obtained. INTRODUCTION Pressure build-up data from shut-in wells have been used by the petroleum industry to determine the permeability of the formation, to estimate wellbore damage, to evaluate the static reservoir pressure and to speculate reservoir volume. Calculation of these factors is based on methods of analysis developed for theoretical systems whose build-up curves have a charac- teristic shape when the wells are shut-in at the sand faCe.1,2,3,5,8,10 However, field curves obtained by conventional surface shut-in methods do not always exhibit this characteristic. Such factors as stratification, rock heterogeneities and irregular reservoir geometry can cause the character of a build-up curve to deviate from that predicted by theory for a simple system. In addition, all field build-up data are affected by the methods utilized in obtaining the measurements. Conventional surface shut-in techniques allow two effects to occur which contribute directly to the manner in which pressure builds up at the sand face. The first, afterflow, has been recognized for some time and methods are available for estimating the magnitude of its effect and for correcting its influence.' The second, phase segregation in the tubing column after shut-in, has been reported only recently and appears to exert a considerable influence on the character of field build-up curves.!' In extreme cases, phase segregation can produce "pressure humps" in the early portion of the build-up curve. Such curves have been considered anomalous and have defied analysis. It is the purpose of this paper to discuss the effect of phase segregation in the tubing string during build-up and to present a bottom-hole shut-in technique for obtaining field build-up data which minimizes the influence of afterflow and eliminates phase segregation effects. It will be shown that reliable reservoir information can be calculated from build-up measurements obtained using this method, even though conventional surface shut-in tests on the same wells yield anomalous data. DISCUSSION OF PHASE REDISTRIBUTION EFFECTS Some of the effects of phase redistribution on pressure build-up curves have been described previously by Matthews and Stegemeier" who have presented evidence that phase segregation is responsible for the pres-

By Robert S. Archer

THE proper material of construction for a given purpose is that material which meets the requirements satisfactorily at the lowest ultirnatc cost. It is consistent with this principle that most aluminum castings are made of an alloy containing about 8 per cent. copper. This alloy possesses mechanical properties satisfactory for general engineering purposes together with manufacturing characteristics leading to the production of finished castings at low cost. It is to the aluminum industry what gray iron is to the iron and steel industry. Just as some services require "semi-steel," malleable castings or steel castings instead of gray iron, there is a certain and growing demand for aluminum castings of superior strength or ductility, or both. Since the beginning of .the industry producers and others have sought to develop alloys or processes by which such castings could be made. Out of these efforts have emerged many alloy compositions and special processes, of which only a few have had sufficient merit to survive. It is the purpose of this paper to describe those which seem to the authors to offer the greatest promise for the production on a commercial scale of aluminum castings of superior mechanical properties, with special reference to heat-treated castings. The suitability of an alloy or process for actual manufacture is affected by so many factors that the problem of appraisal is not a simple one. Since this is such an important part of the whole subject it is proposed to discuss briefly some of the requirements. The final verdict is of course the result of commercial trial and experience. It will therefore, perhaps, be profitable to employ a somewhat historical method of treatment in discussing the subject of alloy development. The alloys or processes to be used in the production of aluminum castings are to be considered from the standpoint of their effects on both the utility and the cost of the finished casting. Specific gravity and mechanical properties come under the first head, while the properties

Jan 1, 1927

By Richard Miller

RECENT studies of creep have made it apparent that plastic deforma-tion may occur in metals under stresses less than the elastic limit as deter-mined from short-time tests. In summarizing conclusions drawn from creep tests by various investigators, Tapsell1 said: "It is evident that if a material has a true elastic range, the elastic limit must represent the maximum stress for no creep." The presence of a. definite elastic limit, represented in single crystals by a critical or threshold shearing stress, is claimed by Schmid2, Elam3 and others who have investigated the plastic deformation of single crystals. However, this "law of critical shearing stress" was deter-mined2 from short-time tests, and the measurement of the deformation was made with apparatus primarily designed to observe large amounts of plastic deformation, not to detect elastic changes. Experimental data recently obtained with highly sensitive instru-ments by A. W. Hanson4 on zinc and by Podaschowsky5 on rock salt indicate that the elastic range in single crystals is considerably narrower than formerly was supposed. Moreover, a theoretical possibility of permanent deformation, under the influence of even the smallest shear stress in single crystals above a certain temperature (Td), has been developed by G. I. Taylor6. This evidence seemed to warrant an examination of the elastic limit in large single crystals by means of creep tests. The first metal chosen for examination was zinc.

Jan 1, 1936

By Arthur L. Hall

The purpose of this symposium is to challenge industry to better air classification, and as a first step toward fulfillment, to spotlight three fairly recent, aerodynamically designed, highly efficient air classifiers. This discussion does not intend to imply that present practice is bad. Actually, when present air separators are used for the jobs for which they were originally designed, they give high production and uniform operation, with a minimum of maintenance. The customers of nonmetallic mineral pigment producers, however, are making increasing demands for finer products, such as 99.9 pct -20µ, which appears to be beyond the economic capabilities of standard air separators industrially used over the last 10 to 30 years. Here is an actual example. A 10-ft diam pebble mill is in closed circuit with a conventional 12-ft diam centrifugal air separator, grinding 20-mesh wollastonite to a series of fine grades up to 99.97 pct - U.S. No. 325 mesh (44µ). Fig. 1 shows variations in fineness of mill discharge (or air separator feed), recycle for regrinding (or air separator tails), and product as measured by a wet rotating sieve test. For example, when the mill is turning out a product 80 pct -325, the mill discharge or separator feed is 30 pct -325, and the coarse tailings or recycle is only 5 pct -325. Hence 25 pct of the 30 pct available is accepted as product. This is efficient separation, and the ratio of recycle to feed is only about 2: 1. How- ever, to make a product testing 99.97 pct -325 the separator feed is 62 pct -325 and the coarse tailing 60 pct -325. In this case the recycle ratio is about 13: 1 and the economic limit to produce fineness has been substantially reached with this given equipment and process arrangement.

Jan 10, 1957

By A. B. Cook, C. J. Walker, G. B. Spencer

Although water will displace oil from a petroleum reservoir to a greater extent than gas will, there are some reservoirs in which gas rather than water should be used for pressure maintenance. This is indicated by the high-percentage oil recovery in the case history reports on the Pickton field1 in East Texas and the Raleigh field2 in Mississippi. In gas cycling, total oil recovery includes vaporized products from the immobile oil in addition to oil produced by displacement. If a large part of the immobile oil is vaporized, total oil recovery may be higher than that obtainable from pressure maintenance by water injection. However, the amount of immobile oil vaporized may range from almost 0 to 100 percent, and no simple and reliable method has been presented in the literature for calculating oil vaporization. Development of such a method was the purpose of this study. Several papers concerning the calculation of oil vaporization have been published,3 6 and each is based on the concept dealing with K values — equilibrium constants for the various components in reservoir oils. (K for a component in a system of vapor and liquid in equilibrium is the mole fraction in the vapor phase divided by the mole fraction in the liquid phase.) This appears to be the most logical approach. Yet, the problem is too great for a perfect solution, even with modem laboratories to analyze oils and high-speed digital computers to perform calculations; the number of components in reservoir oils is too large. Because of their complexity no two reservoir oils are exactly alike. Also, K values change not only with variations in pressure and temperature but also with composition of the reservoir oil. In addition, during gas cycling, the lighter hydrocarbons tend to vaporize first. Thus, the reservoir oil becomes more dense and less volatile as gas cycling continues. Furthermore, the greatest amount of oil vaporization occurs near the injection well. Therefore, a simplified method is required for calculating oil vaporization because a rigorous method is not practical. The present methods of calculating vaporization generally require knowledge of the reservoir oil composition in which the mole fractions of the lighter components through hexanes are given; the remaining oil is described as C, + (heptanes and others of greater molecular weights). Assigning one K value for the C,+ system provides the simplest solution, but this incorrectly assumes that K for C, + does not change as gas cycling continues. This assumption can cause large errors because the K value may become less than a thousandth of the original after a large amount of oil vaporization. Another way to solve the problem is to determine changing K values for C, + according to how much of the C, + has been vaporized. To determine these values a sample of the reservoir oil is injected into a pressure-volume cell, and dry gas is batched in and out of the cell. Appropriate measurements and tests are made to determine K

Jan 1, 1970

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967