Search Documents

By Tony B. Szwilski

The paper outlines the parameters required for an estimation of the size of chain pillars for longwall coal mining. The principal parameters are: stress distribution around the edge of the extracted coal panel, strength properties and geometry of the pillars. The principal thrust of the paper is directed toward correlating the chain pillar strength to the magnitude and direction of strata load expected to act on the pillars. A brief review of the pillar strength formulae pertinent to chain pillar stability is given. The chain pillars are categorized as 'yielding' or 'stiff', depending on the duty required of them. The coal measure strata is classified as 'soft' or 'hard' conditions, the degree of competence of the roof and floor greatly influencing the caving characteristics of the gob and the stability of the roof chain pillars.

Jan 1, 1983

By K. J. Miller, R. E. Hucko

The Coal Reparation Division of the Pittsburgh Mining Technology Center conducted an investigation to assess and compare the pyritic sulfur reduction potential of coal-pyrite flotation and high-gradient magnetic separation (HGMS). Tests were run on three coals - an Upper Freeport bed coal, a Lower Kittanning bed coal, and a Pittsburgh bed coal - to establish grade-recovery relationships characteristic of both processes. Representative portions of each coal sample were crushed to two top sizes-nominal - 500 pm (-35 mesh) and nominal - 149 pm (-100 mesh)-and subjected to conventional froth flotation. The froth product was then beneficiated by coal- pyrite flotation or HGMS, to provide a direct technical companion of the two processes. At - 500 pm (- 35 mesh), the size normally employed for coal flotation, both coal-pyrite flotation and HGMS effectively separated pyrite from coal, and the performance of the two processes was essentially the same. At a - 149 pm (- 100 mesh) sire, however, the performance of HGMS exceeded that of coal-pyrite flotation. The separation effected by HGMS were more efficient at - 149 pm (- 100 mesh) than at - 500 pm (- 35 mesh). On the other hand, it was concluded that either the effectiveness of coal-pyrite flotation decreases with diminishing top size or the process has not been optimized to treat material finer than 500 pm (35 mesh).

Jan 1, 1983

The new saw mill at Cache Bay of the Geo. Gordon & Co., Ltd., a subsidiary of International Nickel Co., of Canada, is equipped with the first fully electric saw carriage drives in Ontario. It has a capacity of 120,000 ft of lumber in an 8-hr shift. About half of the mill's production is high grade white pine lumber which is shipped to the general market. The other half, red pine is used in the mining operations of International Nickel in the Sudbury district, 55 miles west of Cache Bay. [ ] Inco with a potential need of 77 million board ft a year, gets only part of its supply from the new mill. The milling firm became an Inco subsidiary Jan. 1, 1948.

Jan 1, 1952

By C. R. Garr, A. R. Troiano

FLAKING or hair-line crack formation has been a major problem confronting the producer of large alloy steel forgings.' Today it is generally conceded that hydrogen in one or more forms in alloy steel sections is a requisite for flaking. Hence an obvious remedy is a thermal cycle that reduces the hydrogen content to some low level. In practice, this generally means holding the material at some subcritical temperature for a period of time depending on the size of the ingot or forging. Another method that will suffice in some cases is to cool large forgings slowly, i.e., bury in ashes. In practice, this hydrogen bake is sometimes accemplished inadvertently by a series

Jan 1, 1958

By J. D. Audley Smith

Heine's " blue test" for copper, as described by the authorities generally, calls for a set of standard colors; and there has been some discussion concerning the relative superiority, for this purpose, of sulphate and nitrate solutions. The whole matter evidently hinges on the preservation of the standard colors in well-stoppered bottles. The apparatus described by Q. L. Heath* cannot be much improved, when very accurate readings are required. The following method was devised for the purpose of doing away with preserved sets of standard colors, by making a fresh standard for each batch of assays. The solutions are prepared in the usual way, each ammoniacal solution being filtered into its separate bottle, and then filled up to the containing-mark and thoroughly mixed. A similar color-bottle, with an " S " etched upon it, to distinguish it from the other bottles, which are numbered to correspond with the samples, is kept to run the standard. About 150 C.C. of water is put into it, and then the amount of acid (sulphuric or nitric) present in each determination, followed by 30 C.C. of ammonia (s. g. 0.90), which should make the mixture strongly ammoniacal. The liquid is now made up almost to the containing-mark (200 c.c.), say within 1 C.C. The lowest assay is selected first and placed alongside the standard, which, at the beginning, contains no copper. A copper-solution is then dropped into the standard from a burette ; and after each addition the bottle is well shaken and compared with the assay-sample. This operation is repeated until the two shades match exactly, when the burette is read and the assay-result is calculated. The assay next in order of depth of color is now taken and treated in the same way, and so on, until the batch is completed. It

Jan 1, 1901

By Carl Gatlin, S. Srini-Vasan

It is shown thar k k ratios cornputed on the as.sutnption that the average sandstone reservoir has a pore-size distribution characrerized by a linear 1/P saturatioN plo are in good agreewient with correspotlding k,,/k,, ratios obfairzed by Wahl, Mul-/ins and Elfrink by correlatiotz of field measurements. Methods of calculating relative permeability data have recently been reviewed and extended.' It was shown that for sandstone reservoirs where ' is approximately a linear function of effective saturation (as suggested first by Corey') it is possible to express relative permeabilities in very simple terms. For systems wetted by connate water and producing oil and gas (gas saturation growing at the expense of oil) the expression for the The accuracy of Eq. I has been frequently confirmed in our laboratories; because of its simplicity we make routine use of it in the analytical solution of proble~ns in reservoir engineering. Nevertheless, comparisons of the k,,,/k,, ratios yielded by Eq. 1 with appropriate reservoir data have been few. The publica- tion by Wahl, Mullins and ElfrinkV of an empirical equation for k,,/k,, ratios is thus of interest since this equation is specificalljl stated to be Vased on the correlation of field measurements made on sandstone reservoirs. Not surprisingly these authors found that it was necessary to

By Malcolm C. Bridges

A review of the application of geomechanics to open stope mining in Australia was recently undertaken for the Australian Mineral Industries Research Association (AMIRA). It compiled the current state of geomechanics and its application to open stope mining, and recommended avenues of research which should be supported by the industry. Information was compiled for eleven mines which use the method. This included their geological setting, the performance of the mining and evolution of the method, properties and behaviour of rock and backfill, and techniques for measurement and analysis. Open stoping accounts for about two-thirds of production from underground mines in Australia. In the future this proportion will progressively increase and the method will become more complex. Overall, the method is being sucessfully applied, but its full potential is not being achieved because a range of problems and limitations are evident within the mines. Many of these are common to several or more mines. These include: zones of poor ground conditions that delay access and stope development; crown pillars that are irrecoverable; substantial overbreak from the walls and backs of stopes; and lack of a widely accepted method to design systems of stopes. Generally, geotechnical information and techniques for applying it to mining are well-developed. However, it nee

Jan 1, 1983

By John Gross

The building of reverberatory furnaces (Fortschaufelungsofen) where ordinary brick, fire-brick and iron are comparatively cheap, is quite a different matter from the building of such furnaces in isolated camps, where proper material is only to be obtained at high cost and with long delays. Time is always a large factor in metallurgical operations, and the metallurgist may find himself in a position where it becomes necessary to erect apparatus and have it running in less time than it would take to obtain material from outside. It is here that he must make use of makeshifts. In Mexico, one of the most important of these is the alluseful adobe. Employed from prehistoric times, it still has its sphere of application in a surprisingly large number of instances requiring an article that can be quickly and cheaply produced. It is quite possible to erect serviceable reverberatory furnaces with no other materials than adobes, stone and wood. The old Mexican smelting shaft-furnace was an example of what can be done with adobes, and the large number of ruins of this class of furnace scattered through the mining districts of Mexico are silent testimony to the genius of a people who demonstrated their capability of adapting material at hand to their needs. The present paper will describe briefly the construction of an adobe reverberatory furnace which is giving good results, can be quickly erected at a low cost, and, if properly built and handled, will last a long time. The material being simply sun-dried, it naturally follows that the construction must be quite heavy. The adobes should be evenly made, with just sufficient straw to hold them together, and not too large in size (9 in. wide, 18 in. long and 4 in. thick

Jan 1, 1902

By E. H. Barton

The necessity, on the Pacific Coast and throughout the semiarid regions in particular, of the conservation of waters for agricultural, industrial and mining purposes has forced itself upon the minds of those directly or indirectly interested in these industries. To meet the requirements of the case, storage must be provided for the flood-waters so abundant during the rainy season in order to insure a constant and unfailing supply during the summer months. Such storage can only be obtained, in the greater number of instances, by the erection of reservoir-walls of great height. The feasibility of employing earth or timber in the construction of such high dams is questionable, especially when (as is often the case) they must be placed in torrential streams. The experience of recent years with masonry dams, throughout this and foreign countries, has demonstrated that such dams, when intelligently and correctly designed and properly constructed, will meet the requirements of larger storage by means of increased height. The failures of masonry dams have been few; only two of any consequence being on record, namely, that of the Puentes dam, in Spain, in 1802, and that of the Habra dam, in Algiers, in 1810.* On the other hand, the failures of wooden and earthern dams are innumerable. The following are some of the most important structures constructed in recent years. The list is taken from Mr. Wegmann's book, just cited: The Furens, Zola, Ternay, Ban and Verdon dams, in France; the Nizar, Lozoya, Villar and the two Hizar dams,

Jan 1, 1900

By M. N., Short

TIE Pioneer mining district, better known as the Superior district, from its principal town, is located in Pinal County in south-central Arizona about 80 miles east of Phoenix and 22 miles west of Miami. The region embraces a confused series of mountain ranges of moderate FIG. I.----SUPERIOR, LOOKING NORTH FROM SOUTH BANK OF QUEEN CREEK. MAGMA MINE IS INDICATED BY WASTE DUMP IN GULCH TO RIGHT OF CENTER. height but precipitous slopes, between which lie irregular valleys filled with alluvial detritus. The average elevation is about 2800 ft. in the valleys and the summits of the ranges reach 2000 ft. above this. Superior is situated on the north bank of Queen Creek where it emerges from one of those ranges into a more or less basin-shaped valley. The drainage of Queen Creek is to the southwest and the flood waters spread out and lose themselves in the desert northeast of Florence, the county seat of Pinal County.

Jan 2, 1926

Jan 1, 1968

By Warren Blauvelt

IN VIEW of the enormous wastes of natural resources, of labor and of capital, due primarily to the economic environment, established by legislation, the general neglect of this phase of the problem of the elimination of waste is difficult to understand. In such a study, the engineering method of attacking a problem should be employed. The engineer does not try to solve his problem by disregarding natural laws, but by utilizing them. The successful engineer establishes an environ-ment in which forces, acting in harmony with natural laws upon an object or objects, will produce the desired results. The engineer who notices that the water level in a vessel, into which a gallon of water per minute is flowing, is two feet higher than the level in an adjacent vessel, connected therewith by a 6-in. pipe, does not assume that the law of gravity has ceased to work, or that water no longer seeks its level; he examines the connecting pipe for obstacles which prevent the free flow of water. Some editors, many reformers and most politicians tell us that the law of supply and demand no longer works; hence governmental control of commerce is necessary. Governmental control may temporarily-that is, until trial proves its futility- "insure domestic tranquility" and "promote the general welfare;" but it cannot "secure the blessings of liberty" which it cur-tails, nor can it "establish justice" which it violates.

Jan 9, 1922

By Milton Lissberger

MILTON L. LISSBERGER, ? New York, N. Y.-Solder is a mechanical mixture of tin and lead, a fact which is susceptible of very simple demonstration. A bar of solder of a grade even as low as 30 per cent. tin and 70 per cent. lead, passed through a buffing machine, will show a surface practically identical with that of a bar of second-quality or reclaimed tin. The buffings, on chemical analysis, will prove to be almost pure lead. According to the best practice, solder is made in the following manner. Virgin pig lead is first melted, and when it is thoroughly liquefied, virgin pig tin is added, together with a small amount of flux; the latter is for the purpose of bringing to the surface the so-called "liver," consisting of impurities that may have remained in either the lead or the tin as a result of incomplete refining. The combined material, when completely liquid, is thoroughly stirred for some hours, and is then cast into small pigs. Just before casting, and continuously during this operation, the molten metal yields dross, consisting largely of the oxides of lead and tin; this should be carefully skimmed off. After the pigs have cooled, they are taken to a smaller kettle, remelted, and cast into the desired shape for use; or if wires, ribbons, etc., are to be made, the solder is cast into slugs suitable for extrusion and rolling. During this second operation, the skimming of dross should be even more carefully done than at first. Hand mixing has proved to be the only reliable method for the production of the best quality of solder, irrespective of its percentages of lead and tin. The best quality of solder is not necessarily that which contains the highest percentage of tin, but rather is that composition which performs best on the required piece of work. In order to produce

Jan 12, 1918

By Louis A. Rosales, Kanji Ono

The anomalous behavior of hydrogen in iron is examined and a new model is proposed It is postulated that hydrogen single and di-interstitials are in equilibrium with each other. When the binding enthalpy of the di-interstitial, B, is assumed to be about 10 kcal per mole, the predicted temperature dependence of the solubility agrees reasonably well with the reported data. Effective diffusiuity is calculated assuming the di-interstitials to be immobile. Since the number of mobile single interstitials is greatly reduced at lower temperatures, the effective diffusivity is decreased. A good agreement in the temperature dependence of diffusivity between theory and experiment is provided with B - 10 kcal per mole. The predicted diffusivity is also a function of total concentration of hydrogen and this appears to be Partly responsible for the large scatter in the reported data. HYDROGEN is known to form an interstitial solid solution with iron.''' At elevated temperatures, it has been well-established that hydrogen enters iron in the dissociated form and occupies the interstices, and that diffusion of hydrogen in iron is via the interstitial mechanism. The concentration, c, permeability, P, and diffusivity, D, of hydrogen in iron have been separately determined and are consistent with each other under the steady-state condition for temperatures above approximately 400°C; that is, the relationship P = c-D holds. At lower temperatures, however, anomalous behavior of hydrogen in iron has been observed by many investigators. The results of experimental studies4-'' of the diffusion of hydrogen in iron are summarized in Fig. 1, in which the values of D are plotted against the reciprocal temperature. Although there is an increasing divergence in observed values of D with decreasing temperature, the values of D at temperatures below approximately 200°C are definitely small as compared with the extrapolation from high-temperature data. The lines shown bracket the region containing the most probable data. The observed values of c6," are plotted against the reciprocal temperature in Fig. 2, where the dashed lines represent Geller and sun's'' most probable isobars at 1 and 100 atm. At high external hydrogen pressure and low temperatures, the values of c observed are higher than those expected from high temperature data. It is generally accepted that certain trapping mechanism is responsible for the anomalies, but the nature of the trapping mechanism has not been clarified. Various types of hydrogen traps were suggested in the literature, such as "rifts" in the lattice dislocations, voids, microcracks, and so forth. However, no quantitative account of the observed behavior has been given in terms of these trapping mechanisms. Formation of methane in hydrogen-charged steel was found by ~odgurski." This appears to explain the existence of the so-called "residual" hydrogen,4 but not the observed anomalies of hydrogen in iron. McNabb and Foster' proposed a mathematical analysis in terms of a trapping mechanism. However, the physical significance of the traps was not clarified. The necessity of evaluating five parameters in their theory made comparison with experiment difficult. In the present paper, a model is proposed in which the anomalous behavior of hydrogen is attributed to the formation of hydrogen di-interstitials at lower temperatures. In this model, it is postulated that single and di-interstitials are in equilibrium with each other. (The hydrogen di-interstitial is to be distinguished from a hydrogen molecule which may exist in voids.) It can then be shown that most of the anomalies can be explained by assuming that the di-interstitials are virtually immobile and that the binding enthalpy of the di-interstitial, B, is approximately 10 kcal per mole. Predictions of the theory agree with the available experimental data reasonably well. THEORY The basic postulate of the present analysis is that single and di-interstitials are in equilibrium with each

Jan 1, 1969

By R. L. Tobie

The degree of automation that has evolved in the dumping and hoisting of ore at the 3A and 3B hoisting shafts of the San Manuel mine is discussed. Motormen underground now dump their own trains at shaft pockets with rotary car dumps which operate semiautomatically. The ore is then drawn out of the 1200-ton shaft pockets into measuring baskets in skip loading stations, loaded into bottom-dump skips, hoisted, and dumped into coarse ore bins on the surface, in a fully automated operation. In an underground control room on the 2075 level midway between 3A and 3B shafts, car dumping, skip loading, and hoisting systems are monitored on lighted control panels which mimic each step in the operation. Here skip loading and dumping are viewed on closed-circuit television.

Jan 1, 1972

By C. E. Agnew

THE Eastern district, composed of New Jersey and eastern Pennsyl-vania, with its native ores, was the cradle of the iron industry of the United States. The district attained and held the leadership in produc-tion of pig iron for over 100 years, from pre-Revolutionary days to approximately 1875. The first shipment of Lake hematite ore was made in 1853. It was a small shipment, transported by a sailing vessel and a canal barge, but it was the beginning of the end of the supremacy of the Eastern district, although at that time the ore was supposed to be too rich to be successfully smelted with the block coal then in use at western furnaces. The iron made from the first shipment of Lake ore was worked into nails by the Sharon Iron Co., at Sharon, Pa. The writer's great-grandfather, David Agnew, and his brother, John P., Agnew, owners and-operators of the Sharpsville furnace, Sharpsville, Pa., worked the shipment through a furnace. Because of this, the writer feels some satisfaction in having been one of a group that solved the problem of making profitable an operation using Eastern district ores exclusively. With the development of Lake mines, and the production and use of coke, the Middle West district gradually assumed the position of leader-ship in production; because, even though the ores were transported 1000 miles by water and rail, its cost figure on pig iron was better than that of the eastern producer whose furnace was next to his mine. Such a cost figure was possible because the ore was naturally rich in iron and reduced easily. It was possible to carry a heavy burden on the furnace, which resulted in large tonnage and low coke per ton of iron. This paper is in no sense a technical one. The purpose is to show that with the proper physical preparation of the Eastern magnetites they will reduce as easily as the Lake hematites, and because of the high iron concentration give the Eastern producer just as much advantage as formally he was at a disadvantage in comparison with the Middle West producer.

Jan 1, 1938

By Benjamin Smith Lyman

There seems to be dire need of repeated preachment against the too-frequent sad neglect of instrumental surveying and mapping in geological surveys. The value of the map as an illustration of the statements and opinions of a report is too apt to be overlooked; and its essential necessity in working out during its construction the proper conclusions from the observed facts is generally altogether misunderstood. Practical geology seeks, of course, to ascertain and indicate the character of workable or unworkable beds or veins, their depth, position, dip, and horizontal course, or strike, even below the surface; also their outcrops, and therefore, if workable, their extent; and so, taking account of their thickness and specific gravity, their weight in tons. It might, therefore, be called quantitative geology. For the study of more abstruse geological questions, too, it is in many cases necessary to gain some knowledge, or reasonable opinion, in regard to such hidden facts. In some cases, careful instrumental surveys are made; in others, from necessity or choice, there are few or no instrumental observations. It was said, 15 or 20 years ago, that there was an engineer in the anthracite-regions who was capable of telling, on first glancing at a new place, exactly what coal-bed was to be found there at a certain depth, and how thick—a splendid second-sight! "' 0, there be,' " you may be tempted to exclaim, " geologists ' that I have seen' geologize ' and heard others praise, and that highly, not to speak it profanely, "'—but let them pass without being fully characterized, lest the temptation towards profanity be altogether too strong. Yet such second-sight does not exceed the expectations of many men of imperfect geological knowledge, men who have heard of marvel-ously successful geological predictions, but are unaware of

Jan 1, 1910

By Thomas J. Pike, Keith G. Kirk, Mark F. Weider, Lawrence E. Welborn

As part of the mine permitting process as delegated by the Surface Mining Reclamation and Control Act of 1977 the regulatory authority must assess the probable hydrologic consequences and cumulative hydrologic impacts of surf ace mining. The U.S. Office of Surface Mining (OSM), in conjunction with Energy & Minerals Technology Assessment and ENCORE Systems Inc., has developed a user friendly groundwater model that is capable of predicting the effects of surface mining on groundwater quality and quantity. The model is a variation of the Prickett-Lonnquist model which has been modified to be specifically applicable to surface mine applications. This model is presently being used by OSM, the states, and industry to determine mining impacts on groundwater resources. The model is designed for use by the hydrologist with minimal computer training. The model accounts for multiple pumping wells, injection wells, multiple mine pits, and mine pit movement through time. This paper presents an example of how the model may be used in permit application review and how the model can be used by industry to simplify permit preparation.

Jan 1, 1983

By Walter C. Smith, O. J. Seeds

METALLIC bismuth was known in the Middle Ages and the name is supposed to come from the German Wismut. The origin of the German name is uncertain. References to bismuth are found in the writings of Valentine, Paracelsus, and Agricola between 1450 and 1550. Early specimens of bismuth were very impure and often were confused with antimony, tin, and zinc. About the middle of the eighteenth century, J. H. Pott, C. J. Geoffroy, and Torbern Bergman succeeded in producing fairly pure bismuth and showed it to be an elementary metal similar in many respects to lead. H. S. Washington has estimated that bismuth occurs in the earth's crust about as abundantly as tungsten and silver; i.e., to the extent of 10-6 or 10-7 pct. It is found as native metal, both alone and associated with tin, copper, and other metals, and in a large variety of ores. The important ores are the sulfide (bismuthinite), the oxide (bismite), and the carbonates (bismutite and bismutosphaerite) . Other occurrences of bismuth are in the vanadate (pucherite), the selenide (guanajuatite), the telluride (tetradymite), and in many complex sulfides, arsenides, and antimonides. Bismuth minerals have been found in many parts of the world but very few of the bismuth deposits have been of economic value, the oxide ores from parts of China being the exception. The major portion of the bismuth production of today is the so-called by- product bismuth. Bismuth often occurs in ores mined and treated primarily for other metals, and during the treatment of these ores

Jan 1, 1953

By Douglas Bunting

With the gradual exhaustion of the upper veins in the anthracite coal-fields, the problem of mining at greater depths acquires increasing importance and demands the consideration .of a number of important factors, one of which is the greater earth-pressure and the consequent necessity of stronger support for the roof. Under the pillar-and-chamber system, almost exclusively followed in the Northen anthracite-field, the highest economy in mining is generally secured by leaving, on first mining, pillars only sufficient to support safely the overlying strata. As to the necessary size of such pillars, the opinions of mining experts are widely divergent. In establishing the width of chambers and pillars, the thickness of vein and its depth below the surface have received little consideration. For instance, it has been quite usual to work both overlying and underlying veins with the same width of chambers and pillars, when the lower vein was two and one-half times as thick, and twice as far below the surface, as the upper. In view of the generally-accepted theory that the crushing-strength of coal-pillars of the same base-area becomes less with increased height, it is probable, in this instance at least, that the moat economical mining has not been secured. This question of adequate pillar-support is economically less important down to about 800 ft. than at greater depths; and it is with reference to mining at these greater depths that the study of the subject here presented has been prompted. The necessity of leaving larger pillars, involving greater mining-costs per ton and also smaller yields per acre, is one of the troubles of deep working. To mine without leaving adequate pillar-supports will result, sooner or later, in a squeeze. Limited areas, it is true, have been mined at certain widths of

Jan 1, 1912