Search Documents

By J. H. Frye, C. P. Sun

A PRIMARY substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver aneys.1-5 It has been shown that at least, four factors are involved: (I) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2.4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. CALCULATION OF RATES OF WORK- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By James A. Barr

The writer's first experience with flotation was during World War I, in the bene-ficiation of Alabama graphite schist ores. One plant used a cone with a peripheral overflow; dried ore was distributed by a rotating disk onto the surface of the water. No reagents were added' The flake-graphite film floated along with some fine silica. Dewatering screens separated the flake. Naturally unit capacities were low but results were satisfactory. Minerals separation mechanical flotation machines were used in another graphite mill. pine oil was added directly to the head cells, with very good results. All the graphite concentrates from both types of flotation were carefully refined after drying by passing through burr mills, followed by very close sizing on sifters. In March 1927, the writer ran a very successful flotation test on minus 28-mesh, deslimed, Tennessee brown phosphate "sand,"† using a mechanical laboratory machine built in the shops of the Anaconda Copper Mining Co., through the courtesy of Ernest Klepetko. The machine was soon converted to a subaeration type, with improved results. This phosphate research program was greatly enlarged and led to the formation of the phosphate Recovery corporation. The development of nonmetallic flotation followed rapidly. The first flotation machine for bene- ficiation of phosphate was installed in January 1928, in a pilot mill, by International Minerals and Chemical Corporation, at Mulberry, Florida. These machines were Minerals Separation, 24-in., sub-,,,tion types, with weir control of pulp between cells. The sand bleeders were very small—about 1¼-in. diameter. As the feed flake. Is to 25 per cent plus 28-mesh material, the cells choked up frequently. This was corrected by cutting a 2 by 6-in. bleeder opening above the impellers, at grid level, which short-circuited the coarse fractions directly into the feed of the next cell. The matter of size classification and grinding was a considerable problem, which does not come within the scope of this article. Because of the troubles noted above, cascade-type roughers were installed in the second flotation plant, built about 1930. Experimental cells had been tried in 1928. General plant layout is shown in Fig. 1 and details of the cascade construction in Fig. 2. The cascade installation in plant NO. 2 gave good results and eliminated troubles due to choke-ups and coarse feed. The capacities and metallurgical results equaled those of the modified 24-in. Minerals Separation flotation machines in plant No. I The objections to the cascade installation are the floor space and mill height required. In 1939 an improved Minerals Separation machine was tested in parallel with the cascades. Extensive tests indicated

Jan 1, 1947

By James A. Barr

The writer's first experience with flotation was during World War I, in the bene-ficiation of Alabama graphite schist ores. One plant used a cone with a peripheral overflow; dried ore was distributed by a rotating disk onto the surface of the water. No reagents were added' The flake-graphite film floated along with some fine silica. Dewatering screens separated the flake. Naturally unit capacities were low but results were satisfactory. Minerals separation mechanical flotation machines were used in another graphite mill. pine oil was added directly to the head cells, with very good results. All the graphite concentrates from both types of flotation were carefully refined after drying by passing through burr mills, followed by very close sizing on sifters. In March 1927, the writer ran a very successful flotation test on minus 28-mesh, deslimed, Tennessee brown phosphate "sand,"† using a mechanical laboratory machine built in the shops of the Anaconda Copper Mining Co., through the courtesy of Ernest Klepetko. The machine was soon converted to a subaeration type, with improved results. This phosphate research program was greatly enlarged and led to the formation of the phosphate Recovery corporation. The development of nonmetallic flotation followed rapidly. The first flotation machine for bene- ficiation of phosphate was installed in January 1928, in a pilot mill, by International Minerals and Chemical Corporation, at Mulberry, Florida. These machines were Minerals Separation, 24-in., sub-,,,tion types, with weir control of pulp between cells. The sand bleeders were very small—about 1¼-in. diameter. As the feed flake. Is to 25 per cent plus 28-mesh material, the cells choked up frequently. This was corrected by cutting a 2 by 6-in. bleeder opening above the impellers, at grid level, which short-circuited the coarse fractions directly into the feed of the next cell. The matter of size classification and grinding was a considerable problem, which does not come within the scope of this article. Because of the troubles noted above, cascade-type roughers were installed in the second flotation plant, built about 1930. Experimental cells had been tried in 1928. General plant layout is shown in Fig. 1 and details of the cascade construction in Fig. 2. The cascade installation in plant NO. 2 gave good results and eliminated troubles due to choke-ups and coarse feed. The capacities and metallurgical results equaled those of the modified 24-in. Minerals Separation flotation machines in plant No. I The objections to the cascade installation are the floor space and mill height required. In 1939 an improved Minerals Separation machine was tested in parallel with the cascades. Extensive tests indicated

Jan 1, 1947

By H. M. Chance, T. M. Chance

The term 'Llow-sulfur coal," as used in this discussion, is limited to coals containing less, or very little more, than 1 per cent. sulfur. For certain purposes it might be advantageous to include coals that contain as much as 1.25 per cent. sulfur, because such coals have been considered as available for making metallurgic coke of fair grade; but the same reasoning might apply to coals containing as much as.1 1/2 per cent. sulfur, if facilities exist for utilizing such coal by admixture with coal containing less sulfur. , In Pennsylvania, it is not possible to define the exact geographic limits of the areas in which coals relatively low in sulfur exist, because variations in the percentage of sulfur occur irregularly and often abruptly. It is not uncommon to find areas, more or less circumscribed in extent, in which the coal is relatively high in sulfur although all the surrounding territory contains low-sulfur coal; and, similarly, small areas of low-sul. fur coal exist in districts where the coal is normally high in sulfur. These generalizations apply, with few exceptions, to the whole area underlaid with bituminous coal in the State of Pennsylvania, and also to each of the individual beds of coal in this state. Pennsylvania is poorly supplied with coals of the low-sulfur class. We find, however, as an offset to this condition, very large areas in which coal ranging from 1 to 2 1/2 per cent. sulfur exists in beds of good workable thickness. This coal, by washing, can be reduced in sulfur low enough to make coke of a high grade. While a considerable tonnage of workable low-sulfur coal remains in the Pennsylvania bituminous districts, it has been necessary to turn to the areas of higher sulfur coal for the supply of metallurgical coke. This utilization of the higher sulfur areas has been made possible either by washing or by selective mining. Washing.—Fine crushing of the entire feed is not generally necessary to the successful washing of Pennsylvania coals. This is due to the fact that the pyrite is rarely finely and uniformly disseminated throughout the coal but is usually confined to high-sulfur benches in the bed or to concentrations on the cleavage planes of the coal. Hence, by graded crushing and sizing it is frequently possible to at once reclaim those portions of the coal bed containing coal that is relatively free from pyrite.

Jan 1, 1920

By C. C. McDermond, Others, B. N. Zavoico

Production of crude oil in Venezuela for the year 1937 was 186,653,-916 bbl., as compared with 155,228,982 bbl. produced in 1936, an increase of almost 31,500,000 bbl. The oil-field strike, which started on Dec. 14, 1936, lasted until Jan. 25, 1937, when a total of 10,000,000 bbl. of production was estimated to have been lost (5,750,000 bbl. in 1936 and the remainder in 1937). Of the total of 186,653,916 bbl. produced in 1937, the Lagunillas field contributed 45.6 per cent, a drop of approximately 10 per cent under 1936 figures; Tia Juana, 14.3 per cent; Quiriquire field, 14.0 per cent; La Rosa area, 13.3 per cent and the Mene Grande field, 7.6 per cent, these being the five leading contributors of the year's production. Detailed production figures by fields and by companies are shown on Table 1. Of the total production of Venezuela the following four major companies accounted for the greater proportion: Standard of Venezuela and Lago Petroleum Corporation together, 48.3 per cent; Shell, 37.4 per cent and Venezuela Gulf, 14.0 per cent. At the end of the year, 2491 wells were producing, of which number 1291 wells were pumpers, or about 52 per cent. Production The accompanying statistics of production record of Venezuela oil fields from its inception to Dec. 31, 1937, shown on Table 2, indicates that the cumulative production reached 1,503,283,228 bbl. In order of importance, Lagunillas leads all the fields, having accounted for about 50 per cent of Venezuelan production, followed by La Rosa area, which produced about 21 per cent; Mene Grande, which produced about 13 per cent, and Quiriquire, which produced 6.5 per cent. Table 3 shows the age of each field. Mene Grande is the oldest, having produced for 24 years; Tarra is next, 21 1/2 years old, and El Mene third, 171/2 years. The gravity of the crude from the various fields, also shown on Table 3, remained unchanged, the only addition being the new Tia Juana field, which averages 15.6' A.P.I. Table 4 shows the method of production by fields as of Jan. 1, 1938; at the end of the year 2491 wells were producing, compared with 2005 wells producing at the beginning of 1937, or an increase of 486 wells. The completions for the year reached 512. Of the 2491 wells producing crude oil, 1291 wells, or approximately 52 per cent, were pumping, 925 (approximately 37 per cent) were flowing naturally and 275 (11 per cent) were on

Jan 1, 1938

By Frank R. Van Horn

It is customary to ascribe two general modes of occurrence to natural gas, namely, shale gas which, as the name indicates, is found in shale, and reservoir gas, which occurs in sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts. Historical Outline The oldest well producing reservoir gas in the district was drilled in 1886 in Newburg for what was then known as the Cleveland Rolling Mill Co. This well was 3,000 ft. deep, and was thought to have reached the "Clinton" formation. Two "sands" showing small amounts of oil were recorded in the Niagara limestone at depths of 2,658 and 2,686 ft. This is about the horizon of the so-called Newburg sand which has proved to be of some importance as a source of gas and oil by recent drilling operations. The rock pressure was reported to be 400 to 500 lb. per square inch, but since the volume was only 14,000 to 16,000 cu. ft. daily, the well was not only considered unsuccessful but was thought to prove the absence of high-pressure gas in commercial quantities in the Cleveland district.

Jan 1, 1917

By John L. Lamont, Walter Crafts

SELECTION of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of hardenability,1 as-quenched hardness,2,3 and tempered tensile strength.4 Ductility and toughness may also be estimated if the steel is completely hardened on quenching,5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In fine-grained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accompanied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to 4 in. in diameter. PROCEDURE The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1o30, 1040, 1340, 3310, 3316, 4320, 4330, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 9310, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.35. The bars were tempered as follows: ½ in., I in., and I 5/8 in., 2 hr; 2 ½ in., 3 hr; 4 in., 5 hr. All bars were air-cooled from the tempering tem-

Jan 1, 1947

By H. S. Kalish, F. J. Dunkerley

Introduction and Previous Work THE determination of the low temperature tensile properties of tin and tin-lead alloys was initiated as part of an extensive research program on the phasial equilibria of tin binary systems below 13.2°C and the property changes associated therewith. A survey of the literature revealed that, although some room temperature tensile data were available for tin and a few tin-lead alloys, there existed no survey report of the low tcmPerature tensile properties of these alloys. Accordingly, the tensile data for tin and a series of pure tin alloys containing from 0.01 to 50 pet lead were measured at eleven temperatures horn — 196 to +20°C and are presented here in survey form. In addition to the importance of these tensile data as a preliminary to certain fundamental research, this information promises also to be of commercial importance because of the extensive use now being made of tin-lead solders in refrigeration and gas liquefaction equipment. Occasional failures of the solders in low temperature service have been attributed by some metallurgists to low temperature embrittlement, while others hold that failure results from the transformation of the tin-rich phase of the solder from the solid white (beta) to the powdered gray (alpha) form. From the data previously available in the literature, neither of these explanations can be completely corroborated. cohen and van Lieshout have estab-lished the beta to alpha tin transformation at 13,2°C and have shown that strain accelerates the transformation. Further, they showed that although I pct lead retarded the transformation, it was not eliminated. It will be pertinent, then, to note whether the beta to alpha transformation of the tin.rich phase will occur in a short-time tensile 'test. polanyi and schmid2 studied the tensile properties of tin single crystals at — 185°~ and report that tin is britlle at this tem-perature. In 1946, Kostenets3 reported that pure tin was brittle at —Ig6 and — 253°~, while lead remained ductile at both these temperatures. He also studied the tensile properties of tin-lead alloys containing from 10 to 75 pet lead at —253, —196 and + I~OC. The ultimate tensile strength increased more than two times in going from room temperature to — I96°C and about three times that value on further cooling to — 253 C- All the alloys were brittle at — 196'C except those containing more than 75 pct lead. Even at — 253'C, the 75 pct lead alloy retained 36 pet elongation in a 30 mm-ga. length. Creep is also an important phenomenon

Jan 1, 1949

By Roswell P. Angier, Herbert S. Kalish, Henry H. Hausner

POWDER metallurgical methods as applied to zirconium are of great interest because they permit not only the fabrication of parts directly to shape with a minimum loss of material but also the utilization of scrap, and the metal may be processed at temperatures well below the melting point. There are two difficulties involved in the melting of zirconium: 1—High vacuum is necessary for melting, and 2—zirconium reduces nearly all oxides so that it is difficult to find a suitable crucible material. The purest material, zirconium crystal bar, is expensive, and the methods of subsequent fabrication are limited. Cold rolling or extrusion of zirconium crystal bar is suitable for making certain shaped parts, but where melting is involved, the purity of the metal is invariably decreased, and a method of casting to a definite shape does not seem to be feasible. Where it is necessary to hot roll, zirconium must be covered with a steel or copper jacket to protect it from the air. This is necessarily a costly operation. Where annealing of zirconium is necessary it must be conducted in a high vacuum. In an investigation of powder metallurgical methods for zirconium, the zirconium powder used should be characterized by the following properties: 1— Highest degree of purity, 2—uniformity in particle shape and particle size distribution, 3—low compression ratio, and 4—satisfactory strength of the compacted powder (green strength). Zirconium powders have been made by two methods: By the reduction of zirconium tetrachloride (ZrC1,) with sodium,2' *•B "nd by the reduction of zirconium oxide with calcium and calcium chloride." The first method represents one of the earliest attempts to make pure zirconium metal, and the sintered product from this powder is extremely brittle. The second method of making zirconium powder is far more successful, but the powder made in this way has an extremely low apparent density and, therefore, a high compression ratio which makes it difficult to use it for powder metallurgical purposes. For these reasons the above-mentioned zirconium powders were not used in this investigation. To obtain sintered zirconium compacts of highest 'purity and good ductility, it was first necessary to produce a suitable powder. Pure zirconium has been made chiefly by two methods. The iodide method, from which the product is "crystal bar" zirconium, was developed first.'." By this purification process very soft, pure, and ductile zirconium metal can be produced. The second method, developed by the U. S. Bureau of Mines, is the reduction of zirconium chloride with magnesium." The sponge zirconium thus produced is also soft, pure, and ductile.

Jan 1, 1952

By Nathaniel Herz

The use of zinc dust for precipitating the pecious metals from cyanide solutions is well established now in many places, and has many advantages over the shavings method of precipitation. Although much work has been done o,n methods of testing zinc dust, as yet. no absolutely positive test has been devised to determine the value of the material. Certain facts are known, but often it happens that results on a working scale are not as expected from the laboratory tests. The purpose of this paper is to record some obscrvations made while testing a large variety of zinc-dust samples in the laboratory. W. J. Sharwoodl has described standard analytical methods, which have been followed, with the changes noted. The regular determinations include zinc oxide, by solution in ammonia and ammonium chloride, lead, and precipitating efficiency. In some cases cadmium was determined by a method similar to that described by J E Clennell.2 I will discuss the precipitating-efficiency test in detail. The procedure is as follows: "A solution of potassium silver cyanide is prepared by dissolving 10 grams of silver cyanide (AgCN) and 5 grams of 99 %' potassium cyanide in a little water and diluting up to 1000 cc. It is then adjusted by addition of a little more XCN or AgCN until the solution indicates from 0.12% to 0.15% free KCN by titration with standard silver nitrate. The titration is best made by using a 10-cc. or 20-cc. sample, adding 1 CC. of 2 % potassium iodide, and a slight excess of ammonia, as the end point is then sharper. Or 15 grams of pure crystallized XAg(CN)2 may be dissolved in a liter of water and 1.5 grams XCN added. " Weigh out 0.5 gram zinc dust into a 300-cc. beaker. Add a few cubic centimeters of watcr and stir until zinc is well mixed, then pour in 250 cc. of the prepared solution, stirring vigorously. See that all lumps are broken up, and continue stirring for fully five minutes. Stir occasionally (at least every 10 minutes) until the end of two hours from the addition of the solution. Then filter upon an 11-cm. filter, wash precipitate thoroughly, sprinkle with test lead, wrap it carefully in the paper, place in a scarifier with about 20 grams test lead, burn paper cautiously in muffle, scorify five minutes, cupel at low temperature and weigh silver. Milligrams silver obtained from 0.5 gram zinc X 0.0606 = percentage precipitating efflciency."³

Jan 1, 1916

By E. E. Wark, J. Rogers, I. W. Wark, K. L. Sutherland

SOAPS have been used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xanthates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present eminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies.[t] A broad, semi quantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. THE PARAFFIN CHAIN SALTS The basic requirements for a "collector" in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polarnonpolar compounds is the paraffin chain salts: CH3(CH2) „X where X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -CO2Na, -SO3Na, -SO4Na, - PO4Na2, or an aminonitrogen group, the

Jan 1, 1946

By H. C. Burghard, F. R. Brotzen

Experiments were performed to determine the effects of mechanical vibrations on ordering in CuAu. The effects of 5, 10, and 15 kc vibrations were investigated over a range of ordering temperatures of 280° to 360°C. A decrease in the rate of ordering was observed at all frequencies and ordering temperatures. THE effects of mechanical vibrations on certain solid-state reactions have been noted by several investigators. In 1930, Mahoux' reported a substantial increase in the case depth of a steel sample nitrided under the influence of mechanical vibrations over that of an unvibrated sample. Similarly, an accelerating effect of vibrations on the diffusion of chromium in steel was noted. Guillet, in the same year, confirmed the results of Mahoux. More recently Schenck and schmidtmann3 studied the effects of low-frequency, alternating loads on the diffusion of carbon in steel. The results of their experiments, conducted at 500 cycles per min and large strain, (0.2 pct), indicated an acceleration of the process. These workers also reported an increase in case depth of a sample vibrated at 430 kc during a carburizing treatment. Effects of high-frequency vibrations on solid-state reactions have also been investigated by Gudzoff and Gavze6 and Fairbanks and Dewez.7 The former reported an acceleration of the age-hardening process in aluminum alloys. The latter noted changes in the structure and mechanical properties of steel annealed under the influence of vibrations. On the other hand, Altenburg4 and Ehringer5 have given some theoretical reasons and experimental evidence as to the improbability of any effect of vibrations on diffusion. Comprehensive surveys of the effects of vibrations on metallurgical reactions are given by Hiedemann' and Bergmann.9 None of the above investigations led to a physical description of the effects of mechanical vibrations on solid-state reactions. In the present study an attempt was made to gain an understanding of the influence of vibrations on nucleation and diffusion. The order-disorder transformation was chosen for investigation since its mechanism has been extensively discussed in the literature. Moreover, the progress of the transformation may be easily followed by observation of electrical resistance changes. EXPERIMENTAL PROCEDURE The specimens used for the experimental observation of ordering rates were prepared from 50 at. pct Cu-Au alloy wire.* Each specimen consisted of a 0.02-in. diam wire approximately 10 in. long to which two copper potential leads were silver soldered, 2 1/2 in. apart, near one end of the wire. A 1/8-in. diam by 1/4-in. long steel stub was silver soldered

Jan 1, 1960

By G. M. Ritcey, A. W. Ashbrook, E. G. Joe

Solvent-in-pulp extraction of uranium from acid leach slurries of flotation concentrates is described. Solvent extraction was carried out in a 10 in. diam pulsed-plate column. The extractant was a 0.1 M tertiary amine (General Mills Alamine 336) in a kerosene diluent containing isodecanol as an emulsion suppressor and third phase inhibitor. In pilot plant operation at the Beaverlodge mill of Eldorado Mining and Refining, Ltd., slurry feeds containing up to 35% solids were processed at a throughput rate of 13.5 tpd of dry feed. Uranium extraction obtained was as high as 98%. Amine losses to the raffinate were approximately 0.07 lb amine per ton of original dry feed. The Beaverlodge Mill of Eldorado Mining and Refining employs a carbonate leach for the extraction of uranium from the ore.',' Prior to carbonate leaching sulphides are removed by flotation to reduce reagent consumption. This flotation concentrate containing some uranium is then leached with sulfuric acid, filtered, and the uranium precipitated with magnesium hydroxide. The precipitate is then returned to the carbonate leach circuit. Although the tonnage of flotation concentrate treated by acid leaching is low, reagent costs are relatively high. Also maintenance costs on the acid leach filtration circuit were beginning to show significant increases. The choice of solvent extraction-in-pulp as an alternative to the present circuit was influenced by the following factors: 1) elimination of acid pulp filtration, 2) increase in overall recovery because of soluble loss elimination, 3) reduction of reagent cost (mill sodium carbonate solutions are used as strip), and 4) production of higher purity precipitate at the mill site. Because a solvent-in-pulp process would be difficult to test on a bench-scale, the Eldorado experience in the use of pulse columns,3-5 mixer-settlers,6 and solvent-in-pulp operations in particular7 was applied directly to the initial pilot plant carried out during the summer of 1965 and followed by the second pilot plant in 1966. The latter work, which is presented in this paper, determined the following factors for anticipated scale-up to plant production: 1) overall uranium recovery by this process, 2) tonnage throughput expected, and 3) solvent losses anticipated for the full-scale plant. The equipment used consisted of a 10 in. diam extraction pulse column and three mixer-settlers for scrubbing, stripping, and acid equilibration. All equipment was designed by Eldorado and much of the pilot plant was built at the mill site. PROCESS CHEMISTRY Feed to the acid leach plant consists of a sulphide flotation1,2 concentrate containing mainly pyrite, uranium and graphite, with a particle size of 90%

Jan 1, 1968

By Nathaniel Herz

(San Francisco Meeting, September, 1915) THE use of zinc dust for precipitating the precious metals from cyanide solutions is well established now in many places, and has many advantages over the shavings method of precipitation. Although much work has been clone on methods of testing zinc dust, as yet no absolutely positive test has been devised to determine the value of the material. Certain facts are known, but often it happens that results on a working scale are not as expected from the laboratory tests. The purpose of this paper is to record some observations made while testing. a large variety of zinc-dust samples in the laboratory. W. J. Sharwood1 has described standard analytical methods, which have been followed, with the changes noted. The regular determinations include zinc oxide, by solution in ammonia and ammonium chloride, lead, and precipitating efficiency. In some cases cadmium was determined by a method similar to that described by J. E. Clennell.2 I will discuss the precipitating-efficiency test in detail. The procedure is as follows: "A solution of potassium silver cyanide is prepared by dissolving 10 grams of silver cyanide (AgCN) and 5 grams of `99 0' potassium cyanide in a little water and diluting up to 1000 cc. It is then adjusted by addition of a little more KCN or AgCN until the solution indicates from 0.12% to 0.15% free KCN by titration with standard silver nitrate. The titration is best made by using a 10-cc. or 20-cc. sample, adding 1 cc. of 2 % potassium iodide, and a slight excess of ammonia, as the end point is then sharper. Or 15 grains of pure crystallized KAg(CN)2 may he dissolved in a liter of water and 1.5 grams KCN added. "Weigh out 0.5 grain zinc dust into a 300-cc. beaker. Add a few cubic centimeters of water and stir until, zinc is well mixed, then pour in 250 cc. of the prepared solution, stirring vigorously. See that all lumps are broken up, and continue stirring for fully five minutes. Stir occasionally (at least every 10 minutes) until the end of two hours from the addition of the solution. Then filter upon an 11-cm. filter, wash precipitate thoroughly, sprinkle with test lead, wrap it carefully in the paper, plaice in a scorifier with about 20 grams test lead, burn paper cautiously in muffle, scorify five minutes, cupel at low temperature and weigh silver. Milligrams silver obtained from 0.5 gram zinc X 0.0606 = percentage precipitating efficiency."'

Jan 8, 1915

By Harold Markus, Arthur H. Grobe, Gerhard Derge

THE high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as terne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study. has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys.1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. APPARATUS AND METHOD The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from 1/2 to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.? After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been damped. The pH of the electrolyte was controlled? by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. ± 0.10. Potentials were measured against a saturated calomel electrode connected. to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

Not many accounts of mining methods or labor conditions in the mines in early days can be found; all that have seemed to be authentic have been included in the preceding chapters. In practically every field opened before 18.10 the first coal was recovered by quarrying, or strip mining, the operations, of course, being by hand and on a very small scale; new places were opened as soon as mining became difficult or expensive. Where it became necessary to drift into the hillsides, the first coal was taken out by sleds, and later by small wagons, the power being supplied by the miner, often assisted by dogs. Wooden rails then came into use with small cars running on them. These cars were very small, usually holding only a few bushels; in the Belleville, Illinois field as late as 1863 cars having capacities of 10, 12, 14 and some as large as 30 bushels were in use. It was not until late in the 1830's that horses or mules came into use for haulage purposes in the Pittsburgh region, although some had been used in the Richmond, Virginia field at an earlier date. Coal was usually undercut by hand and wedged down, until explosives came into general use, and in nearly every field the coal was forked into the cars, the fine coal, or slack, being left in the mine. Hours worked were very long, but few records remain to show what they were at different places and times; there was undoubtedly a great variation between districts and mines. Roy stated a miner could often produce 5 or 6 tons in a day of 8 or 9 hours in a 5 or 6 foot seam, but in another seam possibly could mine only 3 1/2 to 4 tons. He estimated an average day's work in a four foot seam at about 3 1/2 tons.1 In a strike in the Belleville field in 1863 it was found that an average skilled miner in the field could probably produce 4 to 5 tons a day.2 This was only the coarse coal loaded and did not include slack. In 1873, a coal undercutting machine was tried at a mine about two miles from Brazil, Indiana, said to be the first coal machine ever invented in the United States. It was run by a 5 H.P. steam engine (later to be changed to compressed air), and consisted of an iron rim, four feet in diameter with movable steel teeth placed about one foot apart. The rim

Jan 1, 1942

By D. Van Winkle, C. Zener, H. Nielsen

THe internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. Experimental Method The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress, The general method of making such measurements, and of observing temperature of a specimen during a measurement, has been described.5.6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and goo cycles per second. Specimens The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alpha-brass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at .successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n1/2 where n is the mean number of grains per square millimeter. Experimental Results This paper is concerned exclusively with the part of the internal friction that be. comes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By C. Zener, H. Nielsen, D. Van Winkle

THe internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. Experimental Method The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress, The general method of making such measurements, and of observing temperature of a specimen during a measurement, has been described.5.6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and goo cycles per second. Specimens The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alpha-brass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at .successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n1/2 where n is the mean number of grains per square millimeter. Experimental Results This paper is concerned exclusively with the part of the internal friction that be. comes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944