Search Documents

By Arthur F. Taggart, T. C. Fitt, A. W. Thomas

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By H. W. Camp

ALTHOUGH the situation in the oil industry during the past year has. not been conducive to large expenditures for development and research, there is little indication that such expenditures have been curtailed. While few outstanding achievements have been reported, considerable progress has been made in the development of new products and the adaptation of petroleum derivatives to new uses. The most important question facing the refiner today is the anti-knock quality of his gasoline. This year has seen the widespread adoption of the term "octane number" as a measure for anti-knock values, and in the latter months of the year the public has been made acutely aware of this condition through competitive advertising. Gaso-line is no longer priced on volatility and gravity alone, but on octane number as well; and premiums are being paid for material of relatively high octane rating. The situation has grown more and more competitive and has forced refiners continually to raise the octane rating of their regular and com-petitive grades, and at this writing the same situation exists for premium grades which have possessed relatively high anti-knock properties for some time. Straight-run gasoline produced from paraffin-base or semiparaffin-base crudes has an inherently low anti-knock value, and in order to convert this material to a higher quality it has been found necessary to crack an increasing percentage of the crude oil charge. By completely cracking the heavier portions of the crude, and blending back with the straight-run gasoline, it has been possible to produce an average of 63 to 65 octane number gasoline' on average Mid-Continent crude. This operation carried to the fullest extent does not suffice, however, and the recent and rapid development of the so-called "re-forming unit," has resulted. The straight-run gasoline fraction is cut into two parts: a light, low boiling point gasoline; and a heavy gasoline or naphtha. The latter containing the low anti-knock portions of the gasoline, is sent through a re-forming unit and subjected either to high temperature ,or pressure, or both, which materially increases its octane number. On average Mid-Continent the blend of low boiling point straight-run,

Jan 1, 1932

By Donald L. Katz

The compressing of gas into a partially depleted gas drive oil reservoir to bring the contents to a single phase miscible with gas is proposed as a process worthy of serious study. The compressed gas and vaporized oil would be recovered by cycling. This paper explores the Possibility of recovering oil from reservoirs of 6,000 ft or more by this method. INTRODUCTION Many new methods for increasing the recovery of oil from reservoirs are under consideration in the various research laboratories. One method which should be considered for recovering oil From partially depleted gas drive fields is to compress gas into the reservoir until the contents become a single phase miscible with more gas. Natural gas then may be cycled through the reservoir to recover the oil. This procedure ideally will eliminate the capillary effects of the liquid ill the porous media and should permit recoveries similar to those obtained in cycling operations, probably of the order of 80 per cent. This paper explores the information now available for the prediction of the performance of such a project and discusses the problems likely to be encountered in recovering oil by cycling. For many years dry natural gas has been passed through oil reservoirs to recover natural gasoline which would vaporize from the oil. Recently a process of recovering more of the high boiling hydrocarbons has been described by employing high pressures at which the heavier hydrocarbons have a higher volatility. Nevertheless. this reported method does not eliminate the differential nature of the vaporization process and capillary forces are still present in the reservoir. The process under discussion in this paper would minimize differential vaporization and would remove capillary forces which are responsible for low oil recoveries. Higher gas pressures are required to accomplish this removal of the miniscus, but it does not follow that more gas is required for oil recovery. The process is limited to reservoirs deep enough to permit the use of the required pressure — Probabably 6,000 it and deeper. DESCRIPTION OF THE PROCESS Briefly, the process is to compress natural gas into an oil reservoir which is partially depleted so that it has an oil saturation in the range of 40 to 60 per cent of the hydrocarbon pore space. The injected gas will pass through the channels formerly carrying gas to the wells to build up the pressure and dissolve in the oil phase. This injection will continue without production from the field until the reservoir reaches a single phase. If one were to select unique conditions such that the gas composition, the reservoir oil composition and the Per cent saturation would bring the mixture in the reservoir to the critical temperature and pressure simultaneously the phase behavior accompanying injection is shown by Fig. 1. The oil-gas mixture in the depleted reservoir has a critical temperature at C,. Addition of natural gas to the mixture will give a new critical temperature for each addition. Mixture No. 3 is shown to have its critical temperature at the reservoir temperature and reservoir pressure at P: the critical pressure. Under ideal behavior, the entire reservoir would be at iti critical temperature and pressure and the entire hydrocarbon content would be at a single phase. If the reservoir content were a binary system of methane and a heavy constituent. it would be miscible with more methane. However, for complex mixtures the critical locus does not confine the two phase region, and the dew point curves of Fig. 1 occur above the critical locus. If fluid which was injected into the rezervoir at the critical point were of the

Jan 1, 1952

By D. F. Kaufman, V. V. Damiano, G. J. London, L. R. Aronin

Beryllium bicrystals were Prepared by a seeding and floating zone-melting technique from high-purity beryllium single-crystal material. The starting material was given six floating zone purification passes prior to producing the bicrystals. Symmetric, asymmetric, and antisymmetric bicrystals were tested in tension. Included were bicrystals with boundaries both parallel and perpendicular to the tension axis. Modified symmetric bicrystals were also examined in detail. In these cases, the angles made by the slip planes with the boundary were not equal. Failure by (0001) cleavage, (1180) cleavage, and boundary separation were all observed depending on the orientation of these cleavage planes and the boundary with respect to the tension axis. Failure occurred on whichever system experienced the greatest normal stress. The origin of the fractures observed and the operative dislocation mechanisms were investigated by frac-tography and transmission electron microscopy. The results indicate that low-angle boundaries form in close proximity to the bicrystal boundary and act as sites for crack nucleation. It has been concluded that, although macroscopic compatibility was satisfied in many of the bicrystals examined, the bicrysta1 boundary was effective in Producing "early" failure by local bend plane formation as plastic deformation proceeded, followed by cleavage initiation and crack propagation. SINGLE crystals of high-purity beryllium oriented with the basal plane inclined 45 deg to the tension axis exhibit a critical resolved shear stress of about 300 psi and 200 pct extension by slipping only on the basal plane before failure by cleavage on that plane. Single crystals, oriented with the basal plane parallel to the tension axis, deform by prism slip at a critical resolved shear stress of 9000 psi and exhibit an extension of over 100 pct before failure in a ductile manner.' In contrast to the behavior of single crystals, poly-crystalline beryllium deformed in tension or bending exhibits little or no ductility at room temperature. Beryllium's lack of ductility at room temperature has been attributed to its lack of a sufficient number of independent slip systems. Beryllium has only four independent slip modes at room temperature and according to the Taylor2 and von Mises3 criteria at least five independent shear modes are necessary to completely satisfy the strain compatibility conditions at all the boundaries in a random polycrystalline sample. Studies of beryllium bicrystals thus appear to provide a convenient way in which to determine whether the condition of strain compatibility is a necessary and sufficient condition to prevent failure and whether obviously incompatible boundary conditions result in boundary separation. Bicrystal studies, although not providing all of the constraints encountered in polycrystalline samples, do allow one to select very specific orientation relation-

Jan 1, 1969

By H. B. Goodrich

Anthony I?. Lucas died suddenly at his home in Washington, D. C., on Sept. 2, 1921. Captain Lucas, as he was known to us, was born in Dalmatia, Austria, in 1855, of Montenegrin ancestry. He was graduated as an engineer at the Polytechnic of Grate and served in the Austrian Navy as second lieutenant. In 1879, he obtained leave of absence and visited an uncle in the United States. After an extension of this leave of absence, in order to undertake an engineering engagement in the lumber district of Michigan, where he resided, he decided to become an American citizen. He was naturalized in May, 1885. His name was Luchich, but as his uncle had adopted the name of Lucas, which was more easily pronounced by Americans, from his entrance to this country, he used this Anglo-Saxon form. Without knowing this fact, upon first meeting him a person was sometimes surprised to note the rather Germanic pronunciation of the Captain. Although he subsequently revisited Austria with Mrs. Lucas, he made his permanent home at Washington, D. C. His son served with distinction in the A. E. F. during the World War. His activities in this country as a mining engineer were at first in Colorado and later in salt mining at Petit Anse and Belle Isle, La. During his salt investigations, his attention was directed toward the possibility of oil in the Gulf Coast region and in January, 1901, his well, the "Lucas Gusher," on Spindle Top, Tex., started a new era in the oil business and his reputation as discoverer made him famous throughout the world. Captain Lucas became a member of the A. I. M. E. in 1895. During 1914, 1915, 1918, and 1919, he was chairman of the Petroleum and Gas Committee of the Institute and was at all times prominent in Institute affairs. As to the personality of Captain Lucas, the lasting impression is of a courteous hospitable gentleman, genial, affable, obliging, and helpful with his advice br assistance to any colleague. He was sincere, honest, firm against all obstacles, backing his judgment with his own hard work along any course which he had determined to be correct. His value in the engineering world lies mainly in the petroleum industry. In the oil business all wild-catters are pioneers that deserve credit and gratitude upon their success. There are, however, names that particularly stand out in our history. Drake conquered such obstacles as ridicule, lack of finances, and started the oil business. In 1901, Captain Lucas had the conviction that Spindle Top, a dome rising about 12 ft. above the coastal prairie south of Beaumont, Tex., contained commercial oil. He was scoffed at by practical oil men of the East. Noted geologists

Jan 1, 1921

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. 1 and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width, These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tans to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. 1 and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width, These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tans to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By W. W. Schmittroth, A. Y. Bethune

THE commercial analysis of Special High-Grade zinc usually involves the determination of lead, iron, copper and cadmium as impurities in the base metal. Over the past 20 years, as the result of metallurgical improvements in the art of producing Special High-Grade zinc metal there has taken place a gradual exclusion of almost all extraneous elements, and the few that do remain in the final product have been virtually reduced to the vanishing point. Thousands of tons of zinc .are now commercially produced annually and made available to the trade, in which impurities are present only in the order of 0.0010 per cent or less and the sum total of all impurities does not exceed 0.0025 per cent. To such zinc the term "superpurity" might well be applied without undue exaggeration. The techniques used for production control and final analysis of Special High-Grade zinc by means of emission spectra in the laboratories of the electrolytic zinc plant of the Sullivan Mining Co. are based on the premise that self-electrodes are to be preferred over all other forms for the examination of the zinc in question. Furthermore, after a survey of the literature and considerable experimental work,1 it was decided that the spectrographic method of internal control, the principle of which was first announced by Gerlach,2 using a modification of the high-voltage alternating-current arc source introduced by Duffendack and Thompson,3 with the calibration of each photographic plate as recommended by Wolfe,4 would yield the most accurate and reproducible results. Self-electrodes were chosen in order to make use of one of the unique advantages inherent in spectrographic analysis; namely, the rapid and almost effortless detection of elements other than those being quantified by the analyst; or conversely, the proof that the zinc is free from such impurities if no spectral line of the suspected element appears. This fact was verified for certain elements, and will be discussed later. Carbon electrodes impregnated or packed with zinc salts chemically prepared from the zinc to be assayed were avoided for a number of reasons. First, the chemical manipulation was another time-consuming step, which increased the chances for contamination. Second, none of the common zinc salts, such as the chloride, nitrate or sulphate, yielded reproducible results under our conditions, nor did the spectral line of the impurity appear as readily in the low concentrations as when using zinc metal. Third, no commercial carbon, except the very expensive, was pure enough to use with this grade of zinc and the continued time, effort and expense incurred in the purification of carbon was not desirable. The use of Special High-Grade zinc self-electrodes introduces certain complications with regard to obtaining satisfactory excitation conditions, because it seems necessary to raise the temperature

Jan 1, 1946

By C. D. King

THE key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of IOO per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie- Illinois Steel Corporation. Clairton By-Product Coke Plant And Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By Herbert H. Kellogg

IN 1930, Taggart, Taylor and Knoll1found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the "classical "[t] theory of Brownian movement and proposed an "ionization" theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,"5 Wark's "Principles of Flotation,"6 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.7 Bankoff15 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, all particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid-the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that the addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1945

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future, by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the cog! washer at Clairton made ii possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of IOO per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coai, Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving I6,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used pn all the remaining ovens. The customary arrangement is 7

Jan 1, 1944

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future, by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the cog! washer at Clairton made ii possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of IOO per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coai, Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving I6,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used pn all the remaining ovens. The customary arrangement is 7

Jan 1, 1944

By R. Schuhmann

The expression "unit process " comes up with increasing frequency in discussions among metallurgists and mineral engineers, especially among those concerned with training the next generation. The unit process approach characterizes a significant advance along the road from metallurgy as an empirical art to metallurgy as a branch of engineering. The purposes of this paper are to define and list the unit processes in specific terms, to indicate the scientific and engineering principles basic to all the unit processes, and finally to show how these ideas have been applied to a reorganization of instruction in chemical metallurgy. Unit Operations and Unit Processes Metals are extracted from ores and other raw materials by stepwise procedures. In general, each metallic element is extracted by a different procedure. For many of the metals there is a choice of several flowsheets. However, the procedures all have steps in common. In fact, the many different flowsheets are all made up of a relatively small number of steps which are combined in different groups and sequences. For example, crushing, screening, roasting, sintering, melting, and gaseous reduction are steps which each appear in the Bowsheets for extracting the majority of the metals. The individual steps or flowsheet units can be designated as unit operations or unit processes. These terms are well established in the field of chemical engineering, as the American Institute of Chemical Engineers' definition of chemical engineering shows: " Chemical engineering is that branch of engineering concerned with the development and application of manufacturing processes in which chemical or certain physical changes of materials are involved. These processes may usually be resolved into a coordinated series of unit physical operations and unit chemical processes. The work of the chemical engineer is concerned primarily with the design, construction, and operation of equipment and plants in which these unit operations and processes are applied. Chemistry, physics, and mathematics are the underlying sciences of chemical engineering, and economics its guide in practice."'1a In this definition, the distinction between unit operations and unit processes is that the unit operations are physical while the unit processes are chemical. Table I gives a list of the principal unit operations and unit processes of chemical engineering, taken from Shreve.1b Table 2 lists the principal unit operations and unit processes used for metal extraction. The division between unit operations and unit processes is similar to the chemical engineers' distinction and also correspollds approximately to the division of labor bctween mineral dressing and chemical metallurgy which has been customary in the past. Furthermore, it will be noted that in the proposed classification the unit processes primarily involve chemical reactions and/or changes in state of aggregation; the unit operations primarily do not involve either bulk

Jan 1, 1949

By R. Schumann

THE expression "unit process " comes up with increasing frequency in discussions among metallurgists and mineral engineers, especially among those concerned with training the next generation. The unit process approach characterizes a significant advance along the road from metallurgy as an empirical art to metallurgy as a branch of engineering. The purposes of this paper are to define and list the unit processes in specific terms, to indicate the scientific and engineering principles basic to all the unit processes, and finally to show how these ideas have been applied to a reorganization of instruction in chemical metallurgy. UNIT OPERATIONS AND UNIT PROCESSES Metals are extracted from ores and other raw materials by stepwise procedures. In general, each metallic element is extracted by a different procedure. For many of the metals there is a choice of several flowsheets. However, the procedures all have steps in common. In fact, the many different flowsheets are all made up of a relatively small number of steps which are combined in different groups and sequences. For example, crushing, screening, roasting, sintering, melting, and gaseous reduction are steps which each appear in the flowsheets for extracting the majority of the metals. The individual steps or flowsheet units can be designated as unit operations or unit processes. These terms are well established in the field of chemical engineering, as the American Institute of Chemical Engineers' definition of chemical engineering shows: " Chemical engineering is that branch of engineering concerned with the development and application of manufacturing processes in which chemical or certain physical changes of materials are involved. These processes may usually be resolved into a coordinated series of unit physical operations and unit chemical processes. The work of the chemical engineer is concerned primarily with the design, construction, and operation of equipment and plants in which these unit operations and processes are applied. Chemistry, physics, and mathematics are the underlying sciences of chemical engineering, and economics its guide in practice."1a In this definition, the distinction between unit operations and unit processes is that the unit operations are physical while the unit processes are chemical. Table I gives a list of the principal unit operations and unit processes of chemical engineering, taken from Shreve. lb Table 2 lists the principal unit operations and unit processes used for metal extraction. The division between unit operations and unit processes is similar to the chemical engineers' distinction and also corresponds approximately to the division of labor between mineral dressing and chemical metallurgy which has been customary in the past. Furthermore, it will be noted that in the proposed classification the unit processes primarily involve chemical reactions and/or changes in state of aggregation; the unit operations, primarily do not involve either bulk

Jan 1, 1948

T. L. Joseph (University of Minnesota, Minneapolis, Minn.)—Mr. Killian is to be commended for his inquiry as to why a decrease of 15.3 pct in coke consumption was accompanied by a decrease of only 1.9 pct in the CO/CO, ratio of the top gas. Although I encouraged him in his efforts to find a more significant and meaningful carbon-gas ratio, the method, calculations, and conclusions originated entirely with the author. Whether we agree entirely with the assumptions underlying his corrected ratio, I think we can all agree that a better ratio is needed, and that he deserves credit for recognizing the need and for doing something about it. To be most useful, the CO/CO, ratio for the top gas should reflect the way in which the carbon is gasified in the furnace, particularly the degree of oxidation and the extent of heat release. The effect of CO, from the decomposition of the limestone and the effect of the reaction of CO and water vapor in the upper part of the furnace on the quality of top gas should be isolated from the effect of more basic reactions such as ore reduction and solution loss. The reduction of sufficient iron oxide to produce a ton of pig iron and the accompanying changes in the proportions of the carbon gases can be expressed on a mol basis as follows: 16.5FeA + 16.5CO - 33FeO + 16.5CO, [1] 33FeO + 33.0CO = 33Fe + 33CO. [2] The CO, from eq 1 normally escapes from the furnace because it does not react with coke at the temperature of its release. However, as much as 50 pct of the CO, from eq 2 may react with coke because it is released at temperatures above 1000°C: 16.5CO. + 16.5CO2 = 33CO [3] Thus we see that the gasification of 16.5 mols or about 200 lb of C in solution loss will regenerate as much CO as is required for the last stage of reduction. The pronounced effect of reaction 3 on the final proportions of CO and CO, in the gas stream is obvious. It also follows that reaction 3 materially alters the heat release but it cannot be entirely eliminated in Lake ore practice. A previous study indicates that 100 lb of solution loss may be necessary to maintain the reducing power of the gas. A reduction of 100 lb from the normal level of 200 lb would mean that over 1,-000,000 additional Btu are released in the process. The 100 lb of additional carbon which will be burned at the tuyeres will release 437,000 Btu and the absorption of 583,000 Btu by eq 3 would be prevented. One of the chief objectives of sized ore burdens and more uniform distribution of the gas stream is to minimize solution loss by completing reduction higher in the furnace and in turn to release the maximum amount of heat from the carbon charged. It was odd, indeed, to find that the use of sized ore and sinter in the careful tests reported by Dobscha had changed the CO/CO2 ratio very little. The author has stressed the close correlation between his corrected CO/CO, ratio and production. A correlation of fuel consumption and the CO/CO, might be more logical. Fuel consumption on the prepared ore burden decreased 15.3 pct whereas the corrected CO/CO2 ratio decreased 19.0 pct. Although this agreement between the reduction in fuel and the reduction in corrected CO/CO2 ratio is not as close as the correlation with tonnage, it indicates the corrected ratio is superior to the normal ratio which decreased less than 4 pct. Some adjustment should be made for the reaction: CO + H2O = CO2 + H2 —700Btu [41 because there is evidence to indicate that about one half of the hydrogen is formed in the upper 21 ft of

Jan 1, 1953

By I. A. Lesk

The various materials utilized in the construction of integrated circuits, and the resultant materials interfaces, are discussed with emphasis on a materials system that is compatible with all types of integrated circuits and minimizes the number of different interfaces. Problems with interfaces may originate in the silicon, on its surface, and between other materials within the integrated-circuit package independent of the silicon. ThE difference between integrated-circuit theory and practice may generally be spelled out in terms of the difficulties in fabricating a desired structure. There are, of course, problems in forming the requisite materials, of the necessary composition and geometry, where needed. A distinct class of problem, however, is associated with interfaces— generally between different materials, but occasionally between regions of the same material. We require that each interfacial system perform its proper electrical, mechanical, and thermal function, and do so in an unchanging manner with time under the most severe operating conditions. In a practical sense, we deal in nonideal systems, such that it is generally not possible to form an interface exactly the way it was intended, even if we allow for a knowledge of the practical limitations of the fabrication system. Another way of looking at this situation is to realize that, when we form a group of interfaces under apparently the same experimental conditions, there are often differences of important consequence between them. Very high-magnification pictures, such as are obtained by an electron microscope, reveal fine structure that often differs over the area of a given sample, as well as from sample to sample. Low-magnification pictures look better, but don't eliminate the problem. The trend towards integrated circuits, and away from circuits fabricated utilizing separate components, is very strong in many areas of electronics. A typical silicon monolithic integrated circuit, still in place in the wafer on which it was fabricated, is shown in Fig. 1. The increased reliability which is being experienced through the use of integrated circuits can, to a large extent, be credited to the reduced complexity of the interface system that is present in the electronic system. A glance at Fig. 1, however, with all of its epitaxial and diffused p-n junctions, and interconnect system, shows that interfaces have been far from eliminated. Fig. 2, depicting a schematic cross-sectional view of a (partial) typical integrated circuit, illustrates in detail the numerous interfaces that occur in this type of structure. Besides the individual circuit elements, there are interfaces for isolation, and, Fig. 3, even a crossover requires a series of interfaces. What has been accomplished, however, irrespective of whether or not the total number of interfaces in the circuit is increased or decreased, is that the variety of interfaces is very much reduced. This is because there are fewer materials involved. Since the expense incurred in an R & D program to improve reliability is pretty much directly proportional to the variety of interfaces involved, it is economically advisable to work with integrated circuits for highest reliability. That is not to say that circuits built using standard components could not be made as reliable as integrated circuits, but that the expense involved because of the more complex over-all interface system would be much greater. Although electronic performance utilizing integrated circuits with all silicon elements (i.e., transistors, diodes, resistors, capacitors) is adequate for many applications, there are numerous instances where thin-film passive elements must

Jan 1, 1965

By R. A. Burton, J. T. Hansford, D. A. T. Donohue

Substantial evidence indicates that many petroleum producing horizons contain naturally occurring, ordered fracture systems and that within a particular geologic zone, vertical fractures induced in wellbores often will be directed along a particular compass direction. Both conditions will seriously alter the fluid displacement behavior within reservoirs. In this study the effect of induced fracture orientation and length on sweep efficiency is determined for a five-spot pattern. In general, it is assumed that all wells are fractured and directed along the same compass direction. Using the electrical analog to steady state, two-dimensional fluid flow in porous media, boundary conditions are obtained from which flood fronts are tracked numerically. The numerical computations require a particle tracking routine for approximating flood front histories. It is shown that recovery is sensitive to the length and orientation of fractures for the pattern studied. with the proper design of fracture-pattern systems, recovery can be enhanced considerably. INTRODUCTION Hydraulic fracturing introduced in 1949l gave the industry a rather inexpensive means of increasing the fluid injection or production capacity of wells. It has been used with particular success to increase the production rate of wells completed in tight formations, such as in western pennsylvania2 where producers have fractured in depleted or near-depleted fields and observed economic responses. Once the natural energy declines in such a reservoir where all wells have been fractured, waterflooding is generally suggested as means of further increasing recovery. Of the dual objective sought in waterflooding — high injectivity and high breakthrough sweep efficiency — the former condition can be obtained if all wells in the flood pattern are fractured; the latter condition should depend on the nature of the fracture system. Considerable theoretical work has been published on the nature of fractures induced in boreholes.3-5 Although discussion persists concerning the possibility of forming a horizontal fracture at a given point within the wellbore, it is generally conceded that only vertical fractures will develop below a given depth, i.e., where the fracturing Pressure is less than the overburden load. Given the fact that fractures will be vertical in most cases of interest, it is also important to know whether there is order to fracture orientations within a given geological region. Kehle has suggested that in tectonically relaxed areas of uncomplicated geology, the stresses are fairly uniform and all fractures in the region should be parallel.5 Dunlap arrived at a similar conclusion in a theoretical investigation of localized stress conditions surrounding the borehole.6 He concluded that most vertical fractures are propagated in a preferred azimuthal direction. Fraser and Pettitt, in extending these theoretical suggestions to a specific field case, used an impression packer to record both a vertical fracture and the orientation of this fracture in the wellbore of a well in the Howard Glasscock field, Tex.7 Use of this information enhanced the waterflood recovery of the field. Anderson and Stahl also used impression packers on three fractured wells in the Allegheny field. N. Y.. and found that the fractures were oriented more or less along the same compass direction.8 Orientation of the fractures in this manner depends on the stress condition within the formation during fracturing. Elkins and Skov have demonstrated that a natural, oriented, vertical fracture system exists within the Spraberry field? Heck suggests

Jan 1, 1969

By D. W. Akins

The case history of a combination gas and water flood instituted early in the life of a field is described. It was recognized from the beginning that recovery would be low, under normal production methods, from the several separate, thin beds of porous limestone which had such poor native permeability that the wells would not produce without acidizing. It is thought that the combination flood gives excellent recovery efficiencies for this type of reservoir. The chief function of the gas flood now is to maintain bottom hole pressure in that part of the reservoir which will not be affected by the water injection program until later. Present estimates are that ultimate recovery will be approximately double the recovery expected under the original solution gas drive mechanism. Wide (80-acre) spacing has enhanced the economics of the over-all field program by the elimination of more than $5,000,000 worth of unnecessary wells. INTRODUCTION The Haynesville Pettit Field was discovered in November, 1941, with the completion of T. L. James Co.'s Callie Akin No. 1, located in the W 1/2 of the NE 1/4 Section 27-23N-8W, Claiborne Parish, La., at an approximate depth of 5,300 ft. The center of the field is about two miles north and a mile west of the town of Haynesville, La. A total of 189 producing wells have been drilled on 14,500 acres. An additional nine dry holes were drilled. The Louisiana-Arkansas state line divides the field so that 34 wells are in Arkansas and 155 are in Louisiana. Governmental sections are divided equally to contain eight production units making 80-acre spacing where the sections are regular. Along the state line in Louisiana there is an irregular tier of sections, each of which contains approximately 456 acres. When divided equally into eight production units the spacing is 57 acres per well for these three and a fraction productive sections. All Haynesville Pettit wells are identified by their section number followed by their position in the section as determined by numbering the production units counterclockwise beginning in the upper right corner of the section. All of the producing wells in the field except two are unit-ized and operated by the Haynesville Operators Committee. These two wells are located in the extreme northern part of the field in Arkansas. Efforts to bring them into the Unit are being continued. The Pettit operators organized the Haynesville Operators Committee and the field became a unit operation May 1: 1944. GEOLOGY The Pettit is Lower Cretaceous in age and is defined as the uppermost porosity in the Sligo formation. The unitized area known as the Haynesville Pettit Field is composed of two separate zones of porosity approximately 40 ft apart and without connection between the two, except in wells. These zones are known as the Upper Pettit and the Lower Pettit. The Upper Pettit is separated into two sections throughout most of its area by a relatively thin but quite impervious shale streak. These are called the "A" and "B" sections of the Upper Pettit. All of these lenticular zones are composed of coquina limestone and a small percentage of normal oolites. The large

Jan 1, 1951

By D. W. Akins

The case history of a combination gas and water flood instituted early in the life of a field is described. It was recognized from the beginning that recovery would be low, under normal production methods, from the several separate, thin beds of porous limestone which had such poor native permeability that the wells would not produce without acidizing. It is thought that the combination flood gives excellent recovery efficiencies for this type of reservoir. The chief function of the gas flood now is to maintain bottom hole pressure in that part of the reservoir which will not be affected by the water injection program until later. Present estimates are that ultimate recovery will be approximately double the recovery expected under the original solution gas drive mechanism. Wide (80-acre) spacing has enhanced the economics of the over-all field program by the elimination of more than $5,000,000 worth of unnecessary wells. INTRODUCTION The Haynesville Pettit Field was discovered in November, 1941, with the completion of T. L. James Co.'s Callie Akin No. 1, located in the W 1/2 of the NE 1/4 Section 27-23N-8W, Claiborne Parish, La., at an approximate depth of 5,300 ft. The center of the field is about two miles north and a mile west of the town of Haynesville, La. A total of 189 producing wells have been drilled on 14,500 acres. An additional nine dry holes were drilled. The Louisiana-Arkansas state line divides the field so that 34 wells are in Arkansas and 155 are in Louisiana. Governmental sections are divided equally to contain eight production units making 80-acre spacing where the sections are regular. Along the state line in Louisiana there is an irregular tier of sections, each of which contains approximately 456 acres. When divided equally into eight production units the spacing is 57 acres per well for these three and a fraction productive sections. All Haynesville Pettit wells are identified by their section number followed by their position in the section as determined by numbering the production units counterclockwise beginning in the upper right corner of the section. All of the producing wells in the field except two are unit-ized and operated by the Haynesville Operators Committee. These two wells are located in the extreme northern part of the field in Arkansas. Efforts to bring them into the Unit are being continued. The Pettit operators organized the Haynesville Operators Committee and the field became a unit operation May 1: 1944. GEOLOGY The Pettit is Lower Cretaceous in age and is defined as the uppermost porosity in the Sligo formation. The unitized area known as the Haynesville Pettit Field is composed of two separate zones of porosity approximately 40 ft apart and without connection between the two, except in wells. These zones are known as the Upper Pettit and the Lower Pettit. The Upper Pettit is separated into two sections throughout most of its area by a relatively thin but quite impervious shale streak. These are called the "A" and "B" sections of the Upper Pettit. All of these lenticular zones are composed of coquina limestone and a small percentage of normal oolites. The large

Jan 1, 1951

By J. W. Marx, R. H. Langenheim

The injection of heat-bearing fluids may offer a wider application to secondary and tertiary recovery from conventional oil reservoirs than inderground combustion since the process is more easily controlled and the reservoir requirements, in general, are less critical. In all cares, conduction heat losses to overburden and un-derburden will impose an economic limit upon the size of the area which can be swept out from any one injection point for any given set of conditions. The present report describes a method for c.rtin~ating thermal invasion rates, cumulative heated area, and theoretical economic limits for sustained hot-fluid injection at a constant rate into an idealized reservoir. Full allow-ance is made for non-productive reservoir heat losses. Required solutions can be obtained directly from the numerical tables given here, as soon as all operating conditions are specified, withou extensive mathematica1 ~nanipulation on the part of the user. The injection of a heat-bearing fluid into a reservoir is frequently proposed as a means of secondary or tertiary oil production. This form of thermal recovery may offer a wider application to conventional oil reservoirs than underground combustion since the process is more easily controlled and the reservoir requirements, in general, are less critical. Because of its large gross heat capacity, steam appears to be the most efficient heat injection medium, although mixtures of steam and other gases, hot water, hot oil and hot non-condensable gases also have been employed. Whatever the nature of the injection medium, economic evaluation of such thermal recovery processes will depend upon thermal invasion rates, or rates of productive reservoir heating, at any given time after the start of heat injection. In all cases, conduction heat losses to overburden and underburden will impose an economic limit upon the size of the area which can be swept out from any one injection point, for a given set of reservoir conditions, at any given heat injection rate. The present report describes a method for estimating thermal invasion rates, cumulative heated area and theoretical economic limits for sustained heat injection at a constant rate into an idealized reservoir, making full allowance for non-productive reservoir heat losses. Required solutions can be obtained directly from the nu- merical tables given here, as soon as all operating conditions are specified, without extensive mathematical manipulation. It should be noted that ordinary water flooding may be used to move an annular-heated zone outward, even though the economic areal limit for straight heat injection has been reached. Thus well spacing need not be confined to the areal limits as determined here. However, the present calculations do not cover such supplementary heat scavenging programs. The operating element consists of a radial flow system, concentric about the point of injection, with the idealized step function temperature profile illustrated by the dashed line in Fig. 1. The solid curve shown in Fig. 1 gives a qualitative picture of the true radial temperature distribution. It will be shown later that the expressions given below, which are derived from the simplifying step idealization (dashed line in Fig. I), also can be interpreted in terms of the more realistic temperature distribution shown in Fig. 2. For this case, the thermal invasion radius is simply redefined as the distance from injection well to the mid-point of the temperature distribution.