Search Documents

Jan 1, 1947

By Michael R. Wilder

This paper discusses the two major problems of computerization currently confronting the coal mining industry, specifically, user education and standardization of software practices. Each problem has a unique set of criteria that require addressing individually and collectively. This paper addresses these problems and additionally, a plausible method of overcoming these problems.

Jan 1, 1983

UNIVERSITY OF ALABAMA University, Ala Mining and Metalliaigical Society* G L Roberts, President T G Patterson, Vice-President B B Copeland, Treasurer K F Stark, Secretary G T Bator, Faculty Sponsor F H Crockard, Counselor

Jan 1, 1949

By J. S. Ll. Leach, J. B. Cohen, M. B. Bever

IN the work reported here, the heats of formation of a copper-rich Cu-Sn (a) solid solution and of the Cu.Sn (0 phase were measured by tin solution calorimetry. An approximate determination of the heat effect attending the precipitation of 6 from a supersaturated a solid solution was also made.

Jan 1, 1955

Jan 1, 1943

By A. Whillier

Methods are given for estimating heat flows into mining excavations of various types, with an example to illustrate how the refrigeration requirements are then determined after allowing for the cooling effects of the ventilation air.

Jan 1, 1981

By Ö. Valla, A. Muan, K. Grjotheim

The solid miscibility gap between CaO and "FeO" in the system CaO-"FeO" in contact with metallic iron gradually closes as MnO is added as a third component. On the liquidus surface of the system CaO-"FeO"-MnO, this situation gives rise to a boundary curve which originates in the bounding system CaO-''FeO", proceeds a short distance into the composition triangle of the ternary system, and then vanishes. A new approach has been used to follow the course of this boundary curve. It is shown that the curve vanishes at a much lower temperature and at much lower MnO contents than has been inferred previously. The oxides CaO, "FeO", and MnO together with SiO2 are the major components of the slag phase formed in the basic oxygen process. Hence, the system CaO-"Fe0"-MnO is of considerable technological interest. In addition, the system is theoretically interesting. The three oxides above all have sodium chloride structure. The size differences among the cations are such that in the bounding "binary"* systems CaO-MnO and "FeO"-MnO complete solid-solution series are formed,1,2 whereas in the system CaO-"FeO" there is only limited mutual solubility in the solid state,3 see Fig. 1. Hence, a solid miscibility gap exists in a part of the "ternary"* system Ca0-"Fe0"-Mn0, and a liquidus boundary curve originates at the peritectic point, point a in the insert in Fig. 1, in the system CaO-"FeO", extends a certain distance into the ternary system, and then vanishes. Very little quantitative information on the system Ca0-"Fe0"-Mn0 is available in previous literature. Fischer and Feischer4 sketched isothermal sections at 1600° and 1700°C, and estimated that the vanishing boundary curve extends to approximately 1650°C and a composition of 42 wt pct MnO. The work to be described in the following was aimed at locating experimentally the "vanishing" liquidus boundary curve, determining its end point, and deriving representative isothermal sections below and above the temperature of the end point of this curve. EXPERIMENTAL METHODS The phase relations were determined by the well-known quenching method. (For a description of this method as applied to oxide systems, see the original paper of Shepherd, Rankin, and wright.5) Prereacted oxide mixtures of desired compositions were contained in iron crucibles and heated in a vertical tube furnace in an atmosphere of purified nitrogen. After equilibrium was judged to have been attained, the samples were quenched to room temperature, the phases present were identified by microscopic and X-ray examination, and total iron oxide contents were determined by chemical analysis. "Fisher Certified" reagents (MnCO3, CaCO3, Fe2O3, and Fe) served as starting materials. The calcium carbonate and ferric oxide were heated in air at 400° and 800°C, respectively, for 24 hr prior to use. Manganese oxide was prepared by decomposing the carbonate in a graphite crucible in hydrogen atmosphere at 1000°C. The product was ground under acetone to -100 mesh. The iron powder was used directly without any preparation. Dicalcium ferrite was used as a starting material for some mixtures. It was made by mixing some of the above prepared CaCO3 and Fe2O3 in proportions corresponding to the formula 2CaO. Fe2O3. This mixture was then fired in air for

Jan 1, 1969

By N. S. Bornstein, M. A. DeCrescente

ThE nickel and cobalt base superalloys employed in gas turbine engines under some conditions' oxidize at an accelerated rate when exposed at elevated temperatures to atmospheres containing minor quantities of sea salt. It is generally agreed by investigators in the field that the major steps comprising this phenomena of accelerated oxidation, also called hot corrosion or more commonly, sulfidation, are a) a slag composed primarily of Na2S04 is formed on turbine components, b) the protective oxide scale is rendered ineffectual, c) the slag reacts with. the substrate to form metal sulfides, and d) the substrate is rapidly oxidized. Sodium sulfate, a minor constituent of sea salt, is formed within the gas turbine engine from the reactions between NaC1, the major constituent of sea salt, and the oxides of sulfur.' Depending upon concentration, engine compression ratio, and temperature, the Na2S04 will be present in the gaseous or condensed state. It has been determined that in order for sulfi-dation to occur the Na2S04 must be present in the condensed state.' Although a number of sulfidation mechanisms have been postulated, there is no consistent explanation of oxide scale breakdown and subsequent catastrophic oxidation. Some investigators believe that after oxide scale breakdown, the Na2SO4 reacts with the substrate to form lower-valent sulfur compounds. The accelerated rate of oxidation is due to oxidation of a nickel-sulfide phase." Other investigators believe that sulfur from the fused salt reacts with chromium in the alloy to form chromium-rich sulfides; thereby depleting the alloy of an element which imparts oxidation resistance.3,4 This publication will demonstrate that the accelerated rate of oxidation associated with sul-fidation is due to interactions between Na20, a con-stituent of NazSO.,, ancl the substrate. The aim of this study was to separate and determine the effect of compounds of sulfur and sodium on the oxidation kinetics of various nickel-base superalloys, in order to elucidate the sulfidation mechanism. The work reported herein is sponsored in part by the Naval Ship and Development Center-Investigation of EXPERIMENTAL PROCEDURE The nickel base alloys B-1900, U-700, and Waspaloy were chosen for this study. The nominal compositions are presented in Table I. The specimens, approximately 1 in. by 1 in. by 0.060 in. received in the "as cast" condition were polished with 600 grit emery, washed, and rinsed with acetone immediately prior to oxidation experiments. Sulfida-tion attack was duplicated in the laboratory by apply-ing a saturated aqueous solution of Na2S04 onto the al loy substrate and subsequently exposing the specimens in oxygen at elevated temperature. The method of Na2S04 application is described elsewhere in detail.6 In another set of experiments the affected substrate microstructure associated with sulfidation was reproduced free of the normal oxide scale, by reacting and diffusing elemental sulfur into the alloy. The experimental procedure is also described elsewhere in detail. All oxidation studies were performed using an Ainsworth thermobalance type RV-AU-1, which is readable to 0.01 mg and is reproducible to ±0.03 mg. The specimens, introduced into a heated furnace, were exposed in the temperature range 800" to 1000°C

Jan 1, 1970

By A. J. Teplitz, R. J. Goodwin

A new type water shut-off for use in air drilling has been developed. The method has been 99 to 100 per rent effective in several different formations of inter-ranular-type porosity. Since costs for materials, time and equipment used are relatively small, the process should extend economies of air drilling to many new areas. The treatment involves a new technique for forming a water-inroluble precipitate within the pores of a rock. Advantage it taken of the difference in mobility of a liquid and a gas in porous media to achieve the greatest volume of precipitate in a given pore. Reactants selected for the laboratory (2nd field tests were aluminum sulfate solution and gaseous ammonia. This process has been tested in both intergranular and fractured-type porosities. It has consistently shut-of between 99 and 100 per cent of the water flowing from formations having intergranular-type porosity and perrlreuhilities ranging from a few millidarcise to over a darcy The treatment is not particularly suitable for shutting-off water from fractured formations although plugging of the order of 50 per cent or greater has been achieved in all such applications. Among advantages of the treatment are: (I) no reaction waiting rime after a relatively short placement time, (2) a low mate-rials cost of about $3/f1 of hole treated, (3) use of common service-type equipment for treatment, and (4) no unusual requirements for mixing and placement. INTRODUCTION In rotary drilling with air or gas it has been possible to increase bit life by tenfold and more than double rate of penetration over corresponding performance when drilling with mud. These factors have amounted to as much as 22 per cent savings on total cost of drilling a well. However, these advantages are rapidly lost when water is encountered in an air- or gas-drilled well because water interferes with the removal of cuttings from the hole and also gives rise to other difficulties. In attempting to combat water troubles, operators have commonly resorted to such measures as mist drilling, treatment with cement or chemicals, converting to conventional mud drilling, or setting casing. In many cases these measures have either been costly or ineffective. In an effort to overcome this problem, studies were undertaken to develop an effective and economical water shut-off technique for use in formations possessing inter-granular-type porosity. Extensive laboratory experimentation finally led to a unique method for producing a water-insoluble precipitate within the pores of a sandstone. The unique part of the treatment is use of a liquid and a gas to form the precipitate, and in this case the reactants used were aluminum sulfate solution and gaseous ammonia. The reaction between these two materials is shown in the following equation. Al2 (SO1)3 - 18 H20 6NH2? saturated Water- Solution Cat 2A1(OH)3 . n H20 3(NH4)2SO • n H20 Solid Solid That is, a solid precipitate consisting of aluminum hydroxide and ammonium sulfate is formed when ammonia reacts with aqueous aluminum sulfate. The aluminum hydroxide is insoluble in water and the ammonium sulfate, though soluble, can only be removed from the formation pores by diffusion—an extremely slow process. Although the precipitate formed by the reaction is not particularly firm, great strength is not needed for a precipitate to bridge and plug intergran-ular-type porosity. A flow path in such a system is extremely tortuous and involves a great variety of pore

By H. C. Rogers, B. W. Roberts

Vanadium foils and wires, either cold-worked or recrystallized, show a ductile-brittle-ductile fracture sequence with temperature. At about 150°C the hydrogenated vanadium wires are found to be ductile. At room temperature the wires show brittle fracture, and at liquid nitrogen temperature the wires are again ductile, although to a lesser extent than found at 150°C. Hydrogenated cold-rolled vanadium foils have been found to fracture in unusually straight lines along the [100] texture directions. The hydrogen content required to show this [loo] texture fracture is limited to a few atomic percent in range. Hydrogen content above this range causes fracture to occur in random directions. PRELIMINARY experiments with hydrogenated vanadium foils indicated that the embrittling effect of the hydrogen on the vanadium, which was severe at room temperature, was reduced at both lower and higher temperatures. In order to investigate more quantitatively the ductility changes with temperature, vanadium wires were tested in tension at three temperatures. The reduction of area was measured and the fractures examined. Specimen Preparation—The material used was kindly supplied by A. U. Seyboltl in the form of M-in. rod. The nominal analysis was: 99.2 pct V assay, 0.2 pct C, 0.01 pct Si, 0.01 pct Fe, 0.015 pct Ca, 0.02 pct O,, 0.01 pct N2, and 0.003 pct H,. The specimens were 0.035-in. diam wires. These were prepared by cold-swaging the supplied rod to the final diameter without intermediate anneal. They were finished with long-bearing dies. The surface was then given a light polishing with 0 emery paper and degreased in trichlorethylene. An X-ray check indicated that the cold-swaged wire had a fairly strong [110] fiber texture. The wires were then recrystallized in vacuum in continuously pumped quartz tubes at two temperatures to give two different grain sizes. One group of wires was given 45 min at 800°C; another, 60 min at 1000°C. The microstructures in Fig. 1 show the wires after they have been electropolished and elec-troetched in 10 pct HCI. After the 800°C anneal, the vanadium grains had a diameter of 1 to 2p and there appeared to be a tendency to elongation in the longitudinal direction. However, the latter may be an etching effect. After the 1000°C anneal, the grains appeared to be equi-axed, but there was a very large spread in grain size, probably due to some impurity segregation in the wire, Fig. 1, right. The grain diameters varied between the limits of 1 to 150p. The small particles shown particularly clearly in Fig. 1, left, are also visible on the polished surface of all samples before etching and are undoubtedly carbides and nitrides of vanadium. An X-ray check indicated these annealed wires had a strong [110} recrystallization fiber texture. The hydrogenation was carried out in an iron retort with dry hydrogen flowing through it, the retort and contents being heated in a tube furnace with a hydrogen atmosphere. The hydrogenation temperature was approximately 500°C. The hydro-genation times chosen were approximately those which would be just enough to cause the vanadium to be brittle at room temperature and thus allow the greatest chance for ductility to occur at the other two temperatures. Part of the fine grained specimens were hydrogenated for 21/2 min at 490°C. Part of the coarse grained specimens were hydro-genated for 11/2 min at 515°C.

Jan 1, 1957

By O. N. Carlson, D. G. Alexander

THE hardness anisotropy of metals and alloys has been of increasing interest in recent years but silicon ferrite,1 niobium,2 and tungsten3,4 are the only bcc metals about which this type of information has been reported. This investigation was carried out on vanadium and chromium single crystals in an effort to determine to what degree the hardness variations observed in these metals are due to orientation effects and to compare their behavior with other bcc metals. In earlier work the authors had observed a small angular dependence in the Diamond Pyramid Hardness of single crystalline vanadium on the (100) plane but no anisotropic effects were noted on either the (110) or (111) planes. At the suggestion of R. G. wheeler5 it was decided to investigate this effect in greater detail using the more asymmetric Knoop indentor. The vanadium metal used in the study was prepared by the aluminothermic reduction of V2O5 followed by electron beam melting.6 The principal analyzed impurities were 230 ppm C, 230 ppm O, 65 ppm N, 90 pprn Al, Cr not detected, 50 ppm Fe, 60 ppm Ni, and 200 ppm Si. The chromium was an iodide-refined product obtained from the Chromalloy Corporation. Analysis of this material showed the following amounts of impurities present: 10 ppm C, 9 ppm O, 2 ppm N, 0.4 ppm H, 3 ppm Al, 2 ppm Ca, 2 ppm Cu, 20 ppm Fe, 1 ppm Mg, 0.3 ppm Mn, 1 ppm Mo, 3 ppm Ni, 10 ppm Si, and 1 ppm V. Single crystals of both metals about 1 cm in diam and 10 cm in length were grown by an arc-zone melt- ing technique.7 The chromium crystal was annealed at 1600°C for 6 hr in a purified argon atmosphere to remove any strains or inhomogeneities, but the vanadium was tested in the as-grown condition. The crystals were oriented by the Laue back-reflection method and then sectioned with a spark cutter into individual specimens with a (loo), (110), or (111) plane parallel to the crystal surface. They were mounted in Lucite and carefully ground to a flat surface. The vanadium specimens were then electropolished in a 6 pct perchloric acid-methanol mixture while the chromium specimens were mechanically polished on a Syntron vibratory polisher using an alumina abrasive. The orientation of each crystal was then rechecked by the back-reflection X-ray method. All of them were found to lie within 2 deg of the desired orientation with the exception of the (110)-Oriented chromium crystal which was within 4 deg. Microhardness impressions were taken at 10 deg intervals from the common (110) direction by rotating the crystal in the plane of the crystal surface. A Knoop indentor was used with a 400-g load on the vanadium crystals and an 800-g load on the chromium. The hardness values are averages of 6 impressions and standard deviations were calculated for each set of data. The values reported for the (111) plane of vanadium are based on from 10 to 15 measurements for each point. The microhardness results for vanadium and chromium are plotted as a function of the angular rotation of the long axis of a Knoop indentor from the (110)

Jan 1, 1970

PRESIDENT AND DIRECTOR JOHN M. LOVEJOY NEW YORK, N. Y. PAST PRESIDENTS AND DIRECTORS HOWARD N. EAVENSON PITTSBURGH, PA. HENRY A. BUEHLER ROLLA, Mo. VICE-PRESIDENT, TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y. VICE-PRESIDENTS AND DIRECTORS LOUIS S. CATES NEW YORK, N. Y. PAUL D. MERICA NEW YORK, N. Y. WILFRED SYKES CHICAGO, ILL. R. C. ALLEN CLEVELAND; OHIO HENRY KRUMB NEW YORK, N. Y.

Jan 1, 1936

Jan 1, 1943

By H. M. Howe, W. E. C. Eustis

The processes which form the subject of this paper have been experimented on in the laboratory of W. E. C. Eustis, but have not passed beyond the experimental stage. The first is the invention of Mr. J. L. Thomson, of Capelton, Quebec, Canada, the others have been invented by the writers. Thomson's PRocess foR the Extraction oF Nickel. This consists essentially in first rendering the nickel magnetic, and then separating it from the materials with which it is mechanically vol. X.—20

Jan 1, 1882

By R. E. Hucko

Introduction The principal thrust of the US Department of Energy (DOE) coal preparation R&D program is to develop technology to reduce ash and sulfur content of US coals to levels where the resultant product can be formulated into a high quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. The coal preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in house and by a cross section of industrial organizations, universities, and national laboratories. Research is subdivided into three areas - coal characterization, beneficiation, and ancillary unit operations.

Jan 1, 1985

By Alexander L. Holley

A CHARACTERISTIC, and, to Americans, an amusing discussion of the three-high rail-mill, arose out of the reading of Mr. Lauth's paper on three-high plate-mills, at the Glasgow meeting of the Iron and Steel Institute. From the report of the meeting in the English papers, it appears that Mr. Menelaus, the celebrated rail-maker of Dowlais, could not wait for the discussion of Lauth's plate-mill, but launched at once into the British objections to the three-high rail-mill, which is quite another matter. The American mill, which is very different in principle and ar288

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Feb. 10 to Mar. 10, 1915: W. R. Van Liew, Batoum, Russia. Edward S. Jones, Scranton, Pa. Olof Wenstrom, Boston, Mass. Scott Turner, Tromso, Norway. D. G. Miller, Denver, Colo. A. H. Boyd, Denver, Colo. E. E. Olcott, New York, N. Y. M. M. Thompson, Morsemere, N. J. Francis R. Pyne, Elizabeth, N. J. F. C. Merry, Brooklyn, N. Y. Charles W. Goodale, Butte, Mont. Charles A. Filteau has been appointed General Manager for the Inca Mining & Development Co., Province of Carabaya, Department of Puno, Peru. Charles T. Kruse has been appointed Superintendent of the Jones & r, Loughlin mines in the Marquette and Menominee ranges.

Jan 4, 1915

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman. JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE, Secretary, 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. BENJAMIN B. LAWRENCE. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. HENRY A. WENT WORTH,. Secretary-Treasurer, 60 India St., Boston, Mass. A. H. EUSTIS. F. G. STANTIAL. Columbia Holds four sessions during year. Annual meeting in September or October. FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER. - FRANCIS A. THOMSON.

Jan 12, 1915

By Kenneth N. Weaver

Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War II, however, the industry began to recognize the need for geological exploration, and some of the larger companies began to build a permanent geological staff. This development had its roots in the following factors: Rapid expansion of the industry; closing of many cement plants due to inadequate raw materials; necessity for upgrading the quality of portland cement; and the increasingly large capital investment required to build new cement plants, which in turn, required a higher degree of accuracy in reserve calculations. Whereas the geologist's function during the active expansion of capacity was primarily in exploration, one of his major functions today is the development of existing reserves.

Jan 1, 1965

By Ian M. Thomson, Robert W. Greene

Last August, American Commercial Barge Line Co. (ACBL) began moving coal from mines on the old Camp Breckinridge property in Western Kentucky to TVA's new 2600 MW steam plant at Cumberland City, Tenn. By April of 1973, this movement will reach a level of 7 million tpy. TVA bought the coal rights to this property from the General Services Administration in 1965 for approximately $7 million and is now in possession of reserves containing about 120 million tons of recoverable No. 9 coal, and about the same recoverable amount of No. 11 coal. TVA then contracted through competitive bidding with Peabody Coal Co. to mine the No. 9 seam through two slope shafts. The mines are about 300-ft deep and are separated by the one major fault on this property. The mine portals are approximately 3 ½ mi apart, with the northern portal being over nine miles distant from the Ohio River.

Jan 1, 1971