Search Documents

Jan 1, 1967

By R. V. Norris

The great coal strike of 1902, which confined the work at the Short Mountain colliery of the Lykens Valley Coal Com pany almost exclusively to pumping, gave an opportunity to determine with considerable accuracy the cost of pumping the water from these very old, extensive and wet mines. This colliery, which is located in the extreme southwestern end of the anthracite coal-field, has been operated continuously since 1836, and has shipped 7,747,313 tons of coal. This and the Williamstown colliery are the only operations in Dauphin county. The workings cover about 5 miles along the North dip of the extreme westerly end of the basin, with the operating slopes near the center. They extend around the westerly spoon of the basin and back about 31/4 miles easterly on the South dip. The mines are very deep, the present workings ex tending to 711 ft. below sea-level, and about 1600 ft. below the lowest surface-opening. The coal is hoisted principally from the Short Mountain slope, which is 1550 ft. long, with 26 to 68 degrees dip, and from an inside slope, No. 4, 800 ft. long, with 52 to 72 degrees dip. The ordinary capacity of the colliery is about 1000 tons per day, and the average output for the years 1897 to 1901, in clusive, was 297,000 tons per year. The seams worked are the lowest Red Ash measures, being, respectively, Nos. I, II and III of the coal-bed series, but locally called the " Little Lykens," " Lykens," and " Whites." On the accompanying plan the Lykens seam is shown in full and the Whites in dotted lines. The pumping-plant is divided into four lifts, the pumps being located as shown in the section, Fig. 1, and the plan, Fig. 2.

Jan 1, 1904

Established as a Society February 26, 1957 OFFICERS AND COMMITTEES Wayne E Glenn, President Earl M Kipp, President-elect John S Bell, Past President R A Morse, Vice-President W D Owsley, Vice-President Everett G Trostel, Treasurer Joe B Alford, Executive Secretary 6300 North Central Expressway Dallas 6, Texas

Jan 1, 1960

By H. E. Strauss

The time-to-fracture test has been applied to pure platinum and to two alloys of platinum under the special conditions of small cross-sectional area of the specimens and of a test temperature above the annealing temperature. While the results are similar in character to those secured with large specimens of steel at temperatures below the annealing temperatures, two differences are noted: (I) an upward inflection in the curves for log stress vs. log time for the alloys, and (2) a sharp break in the curve for log stress vs. log time for pure platinum when single crystals filled the wire. The experiments showed that: (I) platinum and 10 per cent rhodium-platinum maintained their strengths at IIOO°C. better than did to per cent iridium-platinum, and (2) the rhodium-platinum after a time exceeded the iridium-platinum in strength at IIOO°C. Platinum alloys in their service at high temperatures encounter conditions somewhat similar to those that exist in the usual form of the "time-to-fracture"l test with steel. This paper is intended primarily to present results obtained by a "time-to-fracture" test under conditions approximating actual service for platinum (at the temperature IIOO°C. under oxidizing conditions) with three materials, pure platinum (99.99 per cent), a platinum alloy with 10 per cent iridium, and a platinum alloy with 10 per cent rhodium. The experimental procedure differed from that previously used in this type of measurement in that the samples were of small diameter (0.010 in.), were fully annealed, and were tested at a temperature definitely above their annealing points (600°C., IOOO°C. and 1050°C., respectively, for 60 per cent cold reduction and 15 min. heating time2,3). The experimental arrangement was similar to that previously described,' using as heating unit a small, horizontal, platinum-wound furnace, ½ by 12 in., maintained at constant temperature by an automatic controller. The samples were 0.010-in. wires, which had been annealed at 1200°C. by drawing them slowly through the furnace. The time-to-fracture was measured electrically. Elongation was not determined because of the difficulties inherent in the experimental arrangement. Life—that is, the time-to-fracture—was considered the important property in these first tests. No attempt was made to measure the reduction in area, but the types of fracture were noted qualitatively; in the text they are referred to as (I) the normal, plastic, or necked fracture, (2) the knife-edge fracture, and (3) the brittle or intercrystalline fratture with small reduction of area. Results for different constant applied stresses are plotted in Fig. I. In all cases at least two trials were made for each stress, although they cannot always be indicated separately on the curves. The breaking Stresses drop very rapidly to a small frat-286

Jan 1, 1943

By H. E. Strauss

The time-to-fracture test has been applied to pure platinum and to two alloys of platinum under the special conditions of small cross-sectional area of the specimens and of a test temperature above the annealing temperature. While the results are similar in character to those secured with large specimens of steel at temperatures below the annealing temperatures, two differences are noted: (I) an upward inflection in the curves for log stress vs. log time for the alloys, and (2) a sharp break in the curve for log stress vs. log time for pure platinum when single crystals filled the wire. The experiments showed that: (I) platinum and 10 per cent rhodium-platinum maintained their strengths at IIOO°C. better than did to per cent iridium-platinum, and (2) the rhodium-platinum after a time exceeded the iridium-platinum in strength at IIOO°C. Platinum alloys in their service at high temperatures encounter conditions somewhat similar to those that exist in the usual form of the "time-to-fracture"l test with steel. This paper is intended primarily to present results obtained by a "time-to-fracture" test under conditions approximating actual service for platinum (at the temperature IIOO°C. under oxidizing conditions) with three materials, pure platinum (99.99 per cent), a platinum alloy with 10 per cent iridium, and a platinum alloy with 10 per cent rhodium. The experimental procedure differed from that previously used in this type of measurement in that the samples were of small diameter (0.010 in.), were fully annealed, and were tested at a temperature definitely above their annealing points (600°C., IOOO°C. and 1050°C., respectively, for 60 per cent cold reduction and 15 min. heating time2,3). The experimental arrangement was similar to that previously described,' using as heating unit a small, horizontal, platinum-wound furnace, ½ by 12 in., maintained at constant temperature by an automatic controller. The samples were 0.010-in. wires, which had been annealed at 1200°C. by drawing them slowly through the furnace. The time-to-fracture was measured electrically. Elongation was not determined because of the difficulties inherent in the experimental arrangement. Life—that is, the time-to-fracture—was considered the important property in these first tests. No attempt was made to measure the reduction in area, but the types of fracture were noted qualitatively; in the text they are referred to as (I) the normal, plastic, or necked fracture, (2) the knife-edge fracture, and (3) the brittle or intercrystalline fratture with small reduction of area. Results for different constant applied stresses are plotted in Fig. I. In all cases at least two trials were made for each stress, although they cannot always be indicated separately on the curves. The breaking Stresses drop very rapidly to a small frat-286

Jan 1, 1943

By Robert S. Williams

NO new ferrous alloys have been produced in the last five or six years that are as outstanding contributions to civilization as were the high-speed steels of the early part of the century or the stainless steels announced at the close of the World War. There have been, however, many developments of major importance having to do either with modifications of existing alloys or with new methods of treatment of older iron or steel alloys. Only a limited number of these new developments can be discussed and their selection does not necessarily imply that these are the most important but merely that they are of general interest rather than perhaps of greater importance in highly specialized fields.

Jan 1, 1939

By Herty, C. H.

The effect of temperature on the physical properties of structural materials has been the subject of many investigations during the past decade. The literature on the effect of elevated temperatures. is voluminous, and during the last four years a great deal of experimental work has been carried out on the effect of low temperatures on the impact properties of steel. For many engineering purposes it is important to know the shock resistance of steels at low atmospheric temperatures, and with the ever-developing field of refrigeration and separation of materials at low temperatures, the normal limits of atmospheric temperature have been exceeded in practice. Iron and its alloys in the unnotched condition have a high impact strength at low temperatures, but in practice variations in type of notches result either from design or accidentally through scratches and surface or internal defects. A study of notched bar impact tests is, therefore, highly important to the engineer. A survey of the literature on low temperature impact testing indicates that chemical composition, heat treatment and method of testing have been the variables which have been considered in most previous work. In only a few instances has any mention of the steel- making method been mentioned and in these the comparison was between steel-making processes and not between steel-making methods on the same process. In view of the wide variations in impact properties at room temperature, in quench and strain ageing and in grain growth of steels of identical chemical composition, (by this is meant the usual five element analysis reported), it was felt

Jan 1, 1957

By M. K. Seguin

The study described in this paper is first centered on the determination of the physical properties (gravimetric, magnetic, electrical, and electromagnetic) o f metamorphosed iron ores of the Carol Lake-Labrador City District. Different geophysical surveys available in the Carol Lake-Wabush area were interpreted quantitatively and the dimensions, attitude, and tonnage of the ore bodies investigated were determined. A geophysical-statistical study was undertaken which permitted the determination of the grade of iron, magnetite, and, subsequently, specularite in the ore bodies. A discussion of the theory and logical progression of the study and the application of the results to actual geophysical data is presented. The conclusions, which are of real significance from the economic standpoint, may be predicted from the data obtained from geophysical surveys before any diamond drilling is undertaken. An integrated interpretation of this type is useful in planning future exploration work and selecting the most favorable geological structures. It also serves as a guide to minimize and determine tonnage drilling patterns. The general conclusion that a restricted range of residual gravity and magnetic anomalies are a key to exploration is valid. Indeed large depths to the top of deposits are absent since all the ore bodies are overturned synclinal structures with tops located close to the surface. Certain irregular geometries do occur but they are not common and the alignment of the iron ore bodies is sub parallel so that magnetic anomalies are evenly reduced in the earth's magnetic field vector.

Jan 1, 1975

By John Ward Smith

Dawsonite-bearing oil shale of Colorado's Green River formation offers a unique and vast (more than 5.9 Gt of A120 j) resource of easily extractable alumina. The processing methods required by the thermal reactions of dawsonite and its oil-shale carrier also require production of shale oil, soda ash, and nahcolite as marketable coproducts. These production methods are presented. The alumina production process is contrasted with the Bayer process to describe technical advantages of extraction of alumina from oil shale which may offset the problems associated with processing a relatively lean ore. While alumina production from oil shale requires development of new technology, the technical problems appear solvable. Only the political problems arising from the now onerous and completely unnecessary federal oil-shale withdrawal appear less solvable.

Jan 1, 1982

By J. K. Edgar

For a number of years the production and use of super-purity aluminum (better than 99.99 pct) has been steadily increasing. High-grade lots of. such aluminum show certain outstanding characteristics not found in lower grades containing principally silicon, iron and copper as impurities. One such characteristic is the so-called "self annealing," that is, the re-crystallization of the heavily cold worked metal at room temperature.' Interest therefore is aroused as to the effects of the impurities. It is well known that the amounts of silicon and copper which occur in aluminum of better than 99.95 pct are completely soluble, at least at elevated temperatures (above 200°C). Iron, on the other hand, is known to be fairly insoluble in solid aluminum. Thus, a knowledge of the limits of this solubility would he of considerable use in studying the characteristics of the high purity metal. All investigators have agreed that iron has very low solubility in solid aluminum. Rosenhain, Archbutt and Hanson2 reported traces of an aluminum-iron phase in the "purest samples of aluminum obtainable." Gwyer and Phillips3 reported that an iron constituent was visible under the microscope in metal containing ".0088 per cent iron." Roth4 found that in the solid state the solubility of iron in high purity aluminum was 0.01, 0.01, 0.017 and 0.022 pct at 225, 320, 500 and 600°C respectively. Dix5 working with alloys containing less than 0.03 pct impurities, concluded from microscopic and chemical analyses of eutectic areas that the eutectic composition was close to 1.7 pct iron. Dix placed the eutectic temperature at 65s°C. Archer and Fink,6 using high purity aluminum-iron alloys, found that the hypoeutectic liquidus intersects the eutec-tic horizontal at 1.7 pct. This is in fair agreement with the investigation of the aluminum-iron system by Gwyer and Phillips who placed the eutectic at 1.89 pct iron with a freezing point of 653'C. Preparation and Chemical Analysis oP Alloys Electrolytically refined aluminum (99.991 pct aluminum) and a high purity alumi-num-iron alloy (11.45 Pet iron) were used in the preparation of the alloys for this investigation. To aid in controlling the iron content of the experimental alloys, an alloy of lower iron content was prepared first from these materials. The high purity aluminum was melted and heated to about 700°C in a plumbago crucible coated with alundum cement and the aluminum-iron alloy was then added. The alloy was thoroughly stirred, fluxed and skimmed and then chill-cast into notch bars. The aIlalyses of the three materials are given in Table I. The alloys for the determination of the solid solubility of iron in aluminum were prepared by melting 600 g total of the aluminum plus the required quantity of the aluminum-iron alloy (No. 92531). These

Jan 1, 1949

CLASSIFICATIONS: 1, Nonferrous metals. 2, Iron and Steel. 3, Petroleum and Gas. 4, Coal. 5, Industrial minerals. A, Geology, exploration. B, Mining and production engineering. C, Preparation and milling. D, Physical metallurgy. E, Administration and economics. F, Chemical metallurgy. G, General. ARIZONA HASTINGS. EARL F., P. 0. Box 10 Chloride 1-A,B,C, Denver Univ., Texas Call. Mines. Asst. chief metallurgist, Old Dominion Copper Co., '26-'29; mine examination and mill construction in Colo.. Ariz.. and New Mexico; mill supt., Arizona Molybdenum Corp.. 34; at present gen. mgr., Pioneer Gold Mng. Co. Specialty: mine examinations and flow sheets of gold and rare metal plants. Examinations limited in Mohave County, A.riz., for present.

Jan 1, 1936

By Charles Bohdanowicz

As in preceding years, the most intensive drilling activity during 1934 took place in the old fields of the western part of the Polish Carpathian petroleum province (district of Jaslo). The number of wells completed to the end of 1934, expressed in percentages, is as follows: Jaslo district, 57 per cent; oil fields outside Boryslaw-Tustanowice-Mraznica, 27; Stanislawow district 8 and Boryslaw fields only 7 per cent. The number of meters drilled (Table 2), expressed in percentages, for the same fields are as follows: Jaslo district, 51 per cent; oil fields outside Boryslaw-Tustanowice-Mraznica, 26; Stanislawow district, 12, and Boryslaw oil fields, 11 per cent. This comparison shows that most of the new

Jan 1, 1935

Organization Place Date 1918 Institute of Metals Division, A. I. M. E Milwaukee, Wis. Oct. 8-11 Iron and Steel Members, A. I. M. E Milwaukee, Wis. Oct. 8-10 American Foundrymen's Association Milwaukee, Wis. Oct. 7-12 American Museum of Safety and Sanitation, Exposi- tion St. Louis, Mo. Oct. -7-12 National Safety Council St. Louis, Mo. Oct. 14-17 Business Show : New York, N. Y. Oct. 21-26 National Society of Naval Architects New. York, N. Y. Nov. 14-15 American Society of Mechanical Engineers New York, N. Y. Dec. 3-6 Geological Society of America Boston, Mass. Dec. 25-31 American Association for the Advancement of Science Boston, Mass. Dec. 27-Jan. 2. 1919

Jan 10, 1918

By Roger L. Beals, George A. Tweedy

I. INTRODUCTION. THE results of the cyanide-operations, given in detail in the following paper, show the progress that is being made at the Minas del Tajo. The old pan-amalgamation process, in operation up to and including 1905, while paying a profit on high-grade ores, was no longer able to treat profitably the ores in sight at that time, hence an alteration in the process was imperative. The success of this alteration is eloquently expressed by the following data Pan- Amalgamation. Cyanidation. 1905. 1907. 1903. Tons treated, . . 51,387 53,983 69,300 Value per ton (U. S. currency),. $10.75 $8.39 $8.28 Extraction, per cent., 65.00 88.50 S7.45 Extraction, per ton. .- $7.00 $7.4.; $7.24 Total cost, per ton treated, 6.50 4.311 4.01 Profit, per ton treated, . . 0.50 3.07 3.23.;

Feb 1, 1910

By R. M. Goldhoff, J. W. Spretnak, R. Speiser

IT has been observed by Grange and Garvey' that the homogenization of boron-treated steels could lead to complete elimination of the hardenability effect caused by boron. The experimental conditions leading to this conclusion involved the heating of steel specimens with and without boron at 2350°F for 24 hr. To prevent oxidation and decarburization, the specimens were encapsulated under vacuum in silica tubes. This observation of permanent deterioration of boron effect was noted in both a 0.63 pct plain carbon steel and a 0.25 pct C low alloy steel, both of which had been treated with ferroboron and homogenized at 2350°F for 24 hr. In another series of boron-treated steels which had been homogenized for shorter times, the effect was to reduce, but not completely eliminate, the boron effect. Under these circumstances, it was presumed that longer heating times would cause permanent deterioration of the boron effect in this series of steels also. Since the characteristic grain boundary constituent could not be formed in any of these steels after homogenization, it was concluded that possibly boron was being converted into an ineffective form through chemical combination resulting from prolonged heating at high temperatures. Assuming the validity of this observation, a series of experiments to establish the relationship between temperature of homogenization and kinetics of deterioration was contemplated. Initially an attempt was made to reproduce the results just described. For this purpose commercial lots of AISI 8640 and AISI 86B40 steels were used. The analyses of these steels appear in Table I. Hardenability evaluation was on the basis of the hardness of normalized sections. Grange and Garvey' pointed out that these steels are air hardening to some extent and such a technique can be used. For these tests the specimens were held for 20 min in a salt bath at 1600°F and then cooled in still air. Several evacuated silica capsules containing pairs of the test steels were made up and heated for 24 hr at 2350°F. A number of failures occurred among these capsules, but evaluation of the specimens successfully treated indicated a complete deterioration of the boron effect. However, examination of the surface of the treated specimens showed that some reaction, probably with the silica tube, had taken place, since none of the specimens was bright. One further test was made at 2350°F for 12 hr, using a pair of specimens wrapped in tantalum foil prior to encapsulation. These specimens appeared bright after treatment, and their hardenability evaluation showed that no deterioration had taken place. Since these steels are extremely sensitive to de-boronization at high temperatures and particularly at long times of holding, the experimental observations raised some doubt as to the real occurrence of the permanent deterioration effect. To resolve this question an experiment was undertaken in which the high temperature portion of the treatment was completed in vacuum. For this purpose a molybdenum wound resistance furnace capable of maintaining good vacuum was used. All the pertinent accessories to this furnace were machined from molybdenum stock in order to withstand the high temperature involved in the experiment. With this equipment a temperature of 2400 °F was obtained and held under a pressure of 5x10-" mm Hg for 24 hr. A specimen of each of the two test steels was suspended in the furnace and both were heated simultaneously. Temperature was measured with a standardized Pt—Pt-13 pct Rh thermocouple, whose millivoltage at 2400°F was extrapolated from the standardization equation, good up to 2200°F. The complete evaluation of these specimens is shown in Table 11. The hardness values attained by each steel after normalizing, both before and after the prolonged high temperature treatment, remain the same. A microscopic study of the decomposition products present in the microstructures of specimens at various points in the heat treatment correlated with the hardness values observed. It seems that no permanent loss of boron hardenability effect occurs, at least in these Grainal-treated steels, when deboronization is circumvented. Acknowledgments This work was conducted under the sponsorship of the Aeronautical Research Laboratory, Wright Air Development Center, under Contract No. AF 18(600)-94, and their support and permission to publish is gratefully acknowledged. A note of thanks is also extended to the Republic Steel Corp. for supplying the materials used in the work. References ' R. A. Grange and T. M. Garvey: Factors Affecting the Harden-ability of Boron Treated Steels. Tro.ns. ASM, 1946, vol. 37, p. 136.

Jan 1, 1957

By Edward Hart

The specimen of glazy iron used for analysis was highly characteristic in appearance. It was made at one of the furnaces of the Glendon Iron Works, working a light burden of ore with a highly silicious cinder. There are very few records of analyses of this variety of iron. I have been able to find but the two given by Bell, and I add these to my analysis for comparison. Bell. 1. 2. Iron,......89.47* 88.18 90.70 Carbon, combined,.... 0.00 0.79 0.71 Graphite,......2.88 2.59 2 68 Silicon,......5.47 5 13 5.13 Manganese,.....1.54 0.77 0.56 Sulphur,......0.04 0.17 0.23 Phosphorus,.....0.60 1.12 1.12 Titanium,.....- 0.26 0.18 Calcium,......0.00 0.22 0.20 Magnesium,.....0.00 0.06 0.03 100.00 9929 101.54

By C. D. Haynes, S. C. Gambrell

The practice of roof bolting in WORLD-WIDE mining activities is very well-known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Various means of stress analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that can be easily analyzed. One of the indirect research methods is the photo-elastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various loading configurations.'-" In-Situ Mine Roof Trusses The photoelastic technique was employed here to evaluate the state of stress above a mine opening where support is provided by the in-situ mine roof truss. This support configuration, shown in Fig. 1, has gained popularity in recent years, particularly in mines with bad roof conditions." To the authors' knowledge, no scientific determination has been made of the advantages roof trusses may offer over conventional bolting configurations comparable to roof trusses. Ordinary mine roofs usually sag or bulge downward soon after mining. Normally, after some movement the roof begins to stabilize, but the face of this bulging mine rock is usually in tension and will almost always fail unless supported. Because rock fails easily in tension, it is desirable to "preload" the roof, that is, to impress a compressive force on the mine roof to prevent bulging and subsequent tensile failure. Ordinary rock bolting installations, particularly if the bolting is perpendicular to the mine roof plane, do not produce a preloading effect. Although bolting installations squeeze the strata together and produce a beam effect desirable for support, they do not have the advantage of actual uplift. They pull down at the anchorage point with a force equal to the bolt tension which sometimes causes a separation in the plane of the anchorage detrimental to roof strength. In-situ mine roof trusses require the installation of steel tension rods in the roof of the mine much the same as conventional roof bolts, except that the rods are arranged to produce a stress pattern above the upper surface of the opening similar to that of a prestressed beam. The roof rock acts to transmit the compression force. The simplest form of truss consists of two steel rods anchored to the back of holes drilled at an angle of approximately 45 over the mine pillars. These rods are collared near the middle of the room, and the lower ends of the rods are connected by tie rods and turn-buckles. Used in this manner, a small-diameter steel rod can provide essentially the same support as a wide-flange steel beam. By tightening the turnbuckles, an uplift on the roof can be produced. Objective of the Investigation The objective of this investigation was to determine qualitatively the state of stress that exists above a mine roof after the installation of the in-situ mine roof truss vs. that of two angle roof bolts, hereafter referred to as "roof bolts," drilled and placed in the same configuration, that is, 45" above each pillar and connected together in the middle of the room by a bearing member such as a steel beam. Each state of stress was to be identified, insofar as possible, as compression or tension above the mine opening. Model Construction A photoelastic model of a mine opening was coil-structed from -in. thick PLM-4B birefringent plastic and was machined to specification shown in Fig. 2. The dimensions of the opening were chosen to simulate a width-to-depth ratio of 3 to 1. Two % -in. holes were drilled at 45" angles, as shown, to provide for the loading devices. After construction, the model was annealed at 240°F to remove stresses produced during machining.

Jan 1, 1971

By Basil B. Zavoico

CRUDE oil production in the United States during 1938 reached approximately 1,214,355,000 barrels, an average of 3,327,000 barrels per day, or 5 per cent below the 1937 record output of 1,279,160,000 barrels. The decreased production did not prevent the stocks of all products from increasing to a total of 575,954,000 barrels by Sept. 30, an increase of 10,957,000 above the total on Jan. 1, or an average daily storage increase in all products of 40,135 barrels. The increase in total stocks was made entirely in the refined products, stocks of crude oil during the first nine months of 1938 having actually declined 7,155,000 barrels to 299,671,000 barrels, or an average daily decline of 26,209 barrels. The 1937 reversal of the preceding five-year trend of discoveries totalling less than withdrawals was continued through 1938 with indicated reserve addition from both new discoveries and extensions considerably in excess of the

Jan 1, 1939

By Howard R. Pratt, Jimmie L. Bratton

The Air Force Weapons Laboratory (AFWL) has been carrying out a series of experiments whose principal purpose is to measure the dynamic response of rock media to large pressure pulses. Coupled with the field experiments have been theoretical calculations simulating this response. These two approaches allow an appraisal of the current ability to measure in-situ rock response under extreme conditions and also give a fair estimate of the current state-of-the-art in the area of computer calculation of the response of "real" geologic media to a large load. The area chosen for the test series is composed of a sequence of sedimentary units (shale, sandstone, and limestone) located in the Estancia Valley 45 miles east of Albuquerque, N.M. (Fig. 1). The units, which dip gently off the uplifted Manzano Mountains to the west, are essentially horizontal at the test site. An extensive geologic and geophysical investigation of the area was carried out in the form of surface mapping and seismic exploration. Numerous holes were cored and material properties were determined from tests of the cores. In-situ geophysical measure¬ments were also carried out. The experiment consisted of loading a 60X40 ft test area with a 4000-psi transient exponentially decaying pressure pulse. The pulse was initiated at one end and traveled the 60-ft length of the test bed. The test area was instrumented with acceleration, velocity, and strain measuring devices placed in drill holes to depths of 30 ft. Theoretical computer calculations of the response of the layered geologic media have been carried out on the AFWL CDC 6600 using one and

Jan 1, 1972

By Robert K. Linn

The New ldria Mining District is in the southern part of the Diablo mountains of the California Coast Range, 140 miles southeast of San Francisco. The district, noted primarily for quicksilver, also has become important recently as a producer of short-fiber chrysotile asbestos. Between 1853 and 1966, the New Idria district produced 568,092 flasks of quicksilver valued at about $55,600,000, 99 per cent of which was recovered from one deposit, the New Idria mine. In 1944, the district was ranked third in all-time production of North American quicksilver districts, and, since that time, the New Idria mine produced an additional 129,045 flasks, placing the district and the New Idria mine second in all-time production. The major structure of the region is the northwest-trending Coalinga anticline consisting of an asymmetric dome of sedimentary beds ranging in age from Jurassic to Quaternary and marked at its northwest end by an oval body of sheared serpentine 14 miles long by 4 miles wide. The serpentine core, rimmed by Franciscan sandstone of probable Jurassic age, was uplifted in stages between Jurassic and Quaternary time and was intruded along a ring of faults into beds of the Panoche Formation of upper Cretaceous age. The core of serpentine and Franciscan rocks is the locus of about 20 quicksilver mines that rim the faultbounded core and lie within the serpentine mass. The host rock of the most productive deposits is altered Panoche shale and sandstone that lies intermittently along the perimeter of the core. Deposits of the New Idria group of mines and those of a few other small mines lie along the northeast contact in the footwall of the New ldria thrust fault, and a few others occur on steep normal faults around the south and southwest. The chief ore mineral in all quicksilver mines is cinnabar, but minor amounts of metacinnabar and native mercury are found in some of the mines. Ore shoots were deposited in fracture zones and stockworks in altered Panoche shale and sandstone and in definite fissure veins in Franciscan sandstone. Rocks made highly amenable to fracturing by hydrothermal alteration were fractured extensively by late faults. The resulting fracture zones, located along the late faults and at changes in strike or dip of the hanging wall or footwall, are the principal controls of most ore shoots. The largest and richest ore shoots are those of the New Idria mine. The major ore bodies occur in fractured shale and sandstone beneath the New ldria thrust fault at its junction with major tear faults.

Jan 1, 1968