Search Documents

By P. R. Gage, R. W. Bartlett

At high temperatues and reduced oxygen pressuves, molybdenum silicicles oxidize to form SiO(g) vathev than a passivating SiO2 film. This is a sevious problem for low-pressure applications of sili-cide-coated rejvactory tnetals. As oxiclalion pvoceeds, the higher oxidntion potential of silicon initially suppresses oxidation of molybdenum and silicon is depleted near the surface. Eventually, silicon depletion causes secondary passivation (SiO2) mid an active to passiue transition in oxidntion behavior at moderately low pressures. At very low pressures, silicon depletion continues until steady-state oxidation of both silicon and rnolyhdenum can proceed at rates propovtional to their initial stoicliiorrzetvies. Ohsel-vations of 'oxidatiou-rate belzcriliov at temperatures from 1101° to 1700°C and oxygen pressures from 10-7 to 1 at in were made using thermogravimetn'c, X-ray diffraction, and elect?*on-rtric?ro/,vobe techniqrres. The experimental results are in good agreement with calculated lirnits for the various types of behavior that were based on tlievtnochernicnl atzd dffusion rate data for the Mo-Si system. A protective oxide film normally forms during the oxidation of elemental silicon. However, at elevated temperatures and reduced pressures this film is not present and oxidation is rapid. wagnerl has shown that this behavior occurs because SiO(g) is more stable than SiO2. The behavior of the silicides at high temperatures is similar but more complicated. Molybdenum and several silicide compounds are involved and the chemical activity of silicon, or the equivalent silicon vapor pressure, can vary considerably in these phases. Also, diffusion in the silicides resulting from reactions in which a higher silicide is reduced to a lower silicide, or molybdenum containing dissolved silicon, must be considered. EXPERIMENTAL AND ANALYTICAL METHODS Isothermal oxidation experiments were conducted using hot-pressed MoSi2 and Mo5Si3 wafers. Each experiment was conducted at a fixed oxygen pressure by controlling the flow of oxygen in and out of the furnace chamber. Most of the experiments were conducted in a molybdenum-wound tube furnace. Special construction features, including use of a high-purity dense A12O3 refractory tube, permitted operation in high vacuum to 1500°C. Higher temperatures could be obtained at higher working pressures and with a sacrifice of tube lifetime. Temperature was measured with three Pt 6 pct Rh/Pt 30 pct Rh thermocouples and controlled with a proportional controller. Weight changes were monitored with a quartz spring balance. The few experiments, at higher temperatures and low pressures, were conducted in a cold wall vacuum chamber using induction heating with direct susceptance of the sample. Because of the variable levitation effect of the induction coil on the sample, weight changes could not be monitored continuously in these experiments. All samples representing both experimental methods were weighed before and after oxidiation and examined with a microscope and analyzed by X-ray diffraction. The analytical treatment assumes equilibrium at interfaces and uses existing thermodynamic data. For convenience, equilibria are expressed as chemical potentials or as vapor pressures of the gases involved. The resulting differences in equilibrium vapor pressure between adjacent interfaces and between the surface and external atmosphere drive diffusion processes in the solid and gas boundary film, respectively. These diffusion processes govern the rate of oxidation. A bibliography of the sources of thermochemical data for the reactions pertinent to the Mo-Si-O system is given in Table I. Reactions are listed with the sources of free-energy data referenced. Since all of these reactions involve one or more gas species, usually oxygen, a plot of the product-gas chemical potential, -RT In Pg, vs absolute temperature for each reaction is given in Fig. 1. These curves can be used to determine equilibrium vapor pressures or to compare the stability of different compounds in the various gases: O2, Si, SiO, and Moo3,. The data of Table I and Fig. 1 were used to determine the analytical results presented in this paper. EXPERIMENTAL RESULTS The weight changes for three MoSi, samples oxidized at 1500°C are plotted against time in Fig. 2. The treatments were identical except for the indicated variance of oxygen pressure and each curve represents one of three characteristic types of behavior that were observed. The upper curve is an example of passive oxidation, which is defined as

Jan 1, 1965

By D. A. Stevenson, R. A. Burmeister

Single-phase silver antimony telluride has been prepared by zone-melting techniques using initial compositions of A new phase appears upon prolonged annealing of this material, but the reaction does not appear to be a simple eutectoid decomposition. A complete analysis of the phase equilibria is complicated by the slow kinetics involved. The Hall coefficient, magneto -resistance, electrical resistivity, and Seebeck coefficient are all sensitive to the presence of second phases. The low Hall mobilities measured for single-phase material indicate that the usual band theory is inadequate to explain the observed transport properties in the system. Density anomalies of up to 2.5 pet between measured and theoretical density were observed but are not conclusive evidence for a defect structure. COMPOSITIONS in the Ag-Sb-Te system have been studied previously by several investigators.1"18 The interest in this system arises from potential thermoelectric applications of alloys on the Ag2Te-Sb2Tes vertical section. Although the composition corresponding to the formula AgSbTe, has received most attention, it has been found to consist of more than one phase.7'8 A thorough understanding of the properties of this heterogeneous material has been impeded by both lack of knowledge of the properties of the homogeneous phases comprising it and the problem of analysis of transport properties in an inhomogeneous system. The present work describes the preparation of the homogeneous ternary phase and the corresponding electrical properties of both homogeneous and heterogeneous material. MATERIAL PREPARATION Most specimens for this investigation were prepared by encapsulating the elements in evacuated quartz tubes after which they were melted and homogenized in the liquid state. The ambient temperature was then dropped to 500°C and the resulting ingot zone melted. The growth rate, width of zone, stoichiometry, and number of passes have an effect on the resultant microstructure. Grains several centimeters in length were easily produced by this method. Other solidification techniques were also used, including uniform slow cooling of the entire specimen and rapid freezing. The microstructures of specimens produced by these techniques frequently differed appreciably from similar compositions prepared by zoning. A variety of nonequilibrium microstructures characterized by long needlelike particles resulted from the rapid-freeze method. PHASE EQUILIBRIA The lack of information on phase equilibria is a major difficulty associated with a comprehensive study of the Ag-Sb-Te system. Considerable confusion has resulted from the use of the formula AgSbTe, to identify the cubic ternary intermediate phase even though it has been established that material of this stoichiometry normally contains AgzTe as a second phase.798 In this paper, silver antimony telluride will denote the cubic ternary intermediate phase comprising the major portion of AgSbTe,. The term "single phase" will denote material which consists of only the cubic phase (as evidenced by metallographic examination and X-ray diffraction) and the term heterogeneous will describe multiphase material containing AgzTe, SbzTe3, or other phases in addition to the cubic phase. The single-phase material may actually contain a variety of inhomogeneities—gradual changes in composition on a macroscopic scale, localized fluctuations in composition, clusters or other products of early stages of the precipitation process, and a variety of point and line defects—all of which will not be detected by the present techniques for determining homogeneity. Single-phase material has been prepared from compositions close to 59 mole pct SbzTe3 21 (this notation refers to the location on the Ag,Te-Sb2TeS vertical section). Zone widths of =2 cm and growth rates 51.2 cm per hr were used. The single-phase region at elevated temperatures extends off the vertical section to a composition which can be expressed approximately as Ag,,SbzgTes,.9 The latter two compositions as well as AgSbTe, are represented in the conventional Gibbs triangle in Fig. 1. It is not presently possible to ascribe exact values to the limits of the single-phase region on a given isotherm or vertical section due to the extremely

Jan 1, 1964

By Boris J. Kochanowsky, Burke O. Trafton

Because of the strict requirements on the quality of limestone that are dictated by the users, the operator was compelled to find new approaches to produce a product of uniform and acceptable quality. The raw material is controlled and monitored every two minutes by a special computer in order to ensure its quality. The required minimum and maximum quality constraint had an adverse effect on performance and consequently cost. In order to improve this performance, a Monte Carlo simulation model was developed and tested for the optimal truck allocation. The input data is based upon the distribution of equipment performances and costs.

Jan 1, 1969

By Chas. H. Behre

MINING geology, both theoretical and practical, continued to make noteworthy progress during 1938. Mining companies generally, stimulated especially by the improvement in economic conditions during the latter part of the year, extended their workings and developed new ore bodies. Federal and state surveys expanded their search for favorable localities and actual ore bodies, with corresponding enlargement of regional knowledge. Theoretical investigations covered geochemistry of ore deposition, structural control of mineralization, and mineralogy of the ores (chiefly aided by the microscope). More geochemical work is greatly needed: ore searching is still too purely empirical, based on features that have been recognized else- where. Thus, clearer understanding of the conditions essential to transportation of metal salts is needed. Jean Verhogen has suggested that solubilities

Jan 1, 1939

By P. B. Bucky

IN this day of steady progress in the mining industry, especially along mechanical lines, the question of whether to discard present equipment for that of a new type often engages the minds of many officials of mining companies. The rapid strides made from year to year sometimes cause this question to be brought up within a year after new equipment has been purchased and installed. It is a moot question whether a machine that has been purchased last year should be replaced by a new one put on the market this year. As I see it, the reasons for the replacement of present equipment may be summed up as follows: (1) because of increased safety; (2) because of legal regulations; (3) because of increased profits. I think all of us, as engineers, will endeavor to put in as safe equipment as it is possible to devise. The tendency of mining companies in that direction is very gratifying.

Jan 1, 1930

By AIME AIME

H OWEVER extensively water-lines may be laid in the mine for fire fighting purposes, there are still, usually, points being worked temporarily, development, stoping or other work of a temporary or incidental nature where it is considered that the expense of laying fire-lines is not warranted. While the laying of water-lines in some sections of the mine may not be warranted, in most metal mines it is necessary to lay an air-line to all working places. In the mine of the United Verde Extension Mining Co., at Jerome, Ariz., advantage has been taken of this fact by providing a means of by-passing the water at the end of the water-line into the air-line in case an emergency arises. By this means the 2-in. air-line can be quickly converted into a water-line for fighting fire which might otherwise be beyond the reach of the water-lines.

Jan 1, 1930

By GILBERT E. SEIL

GREAT advances in the preparation of ores for reduction to ferro-alloys have been made, although standard methods of reduction have been continued at most plants. Efficiencies, yields per furnace, and energy requirements per ton are generally better than previously attained. The advantages of sizing and conditioning of ore, fluxing stone, and coke have been realized. Conditioning varies from drying the furnace burden to chemical rearrangements to facilitate reduction reactions and sometimes to furnish some of the energy required for the reaction before the burden reaches the furnace. During the war period it is impossible to discuss in detail many of the advances made. They are subjects for postwar papers. However, the new procedures mentioned in the following paragraphs are indicative of the work already done and in progress.

Jan 1, 1944

By ELIHU THOMSON

IN 1877, Professor Thomson delivered at the Franklin Institute, [Philadelphia, five lectures on electricity. The object of the lectures and the demonstrations, which were numerous and many of them original even to the employment of special apparatus constructed by the lecturer, was to show clearly that electricity, of whatever name, was the same., differing only in tension (as it was termed) and in the current flowing, or quantity (the old term), in steadiness or in wave-like character. In those days, the textbooks divided the subject into statical and dynamic electricity, with sub-divisions such as frictional electricity, voltaic electricity, magneto electricity, electromagnetism, thermo electricity, and animal electricity. The well-known Ruhmkorff coil,' or spark coil as it is now called (as when used for the ignition of automobiles), was employed to step, up a battery current to a high-tension discharge which would charge condensers, such as Leyden jars.

Jan 1, 1921

By D. A. Dukelow, G. Derge

THE Fe0-Mn0-Si0, system has many properties of fundamental interest besides its occurrence in steel-making. The system is the simplest ternary complication of the FeO-SiO, binary whose electrochemical properties have been explored. Therefore, knowledge of the conformance of Fe0-MnO-SiO, melts to Faraday&apos;s laws, as investigated by current efficiency measurements, would be of particular value in interpreting the observed variations of electrical conductivity, while at the same time furthering understanding of this type of molten oxides. Pertinent to the present study are conductivity data of FeO-SiO, and Fe0-Mn0-SiO2, and current efficiency data of FeO-SiO,. Concerning conductivity measurements, Inouye, Tomlinson, and chipman&apos; studied the specific conductivity, a, of molten wüstite as a function of temperature and oxide addition. Liquid FeO in equilibrium with an iron crucible was found to have a o whose magnitude and positive temperature coefficient were undeniably semiconductor in nature (o1400°C = 269 ohm-1cm-&apos;). Additions at 1400°C of 5 mole pct MnO decreased o to 227 while a similar addition of SiO2, dropped o to 125. Additional SiO2 produced an exponential decline of o. It was reasoned that because wüstite is known to be oxygen excess and since there is no pronounced change in oFeO upon melting, that UFeO(L)is p-type semiconduction. Björling2 gives o data for the ternary FeO-MnO-SiO, using fayalite, 2 FeO-SiO,, as the base substance. Upon addition of tephroite, 2 MnO-SiO, he noted a small decrease in o. Taking his data for 1400°C with one-half of the fayalite replaced by tephroite, o shows a decrease of some 40 pct relative to o for fayalite, i.e., 5 ohm-&apos; cm-&apos; to 3. In line with this observation, Mori and Matsushita3 reported that substituting MnO for FeO in the silicate de- creased o slightly except at high SiO, contents where the decrease was somewhat larger. Investigating the ionic nature of FeO-SiO2 melts, Simnad, Derge, and George4, found the anode current efficiency, C,, as calculated from iron anode weight loss, was temperature invariant and in general increased with SiO2 concentration. The authors suggested the possible presence of electronic conduction to explain why C+ < 100 pct. Fig. 4 includes their results as curve (b). EXPERIMENTAL METHOD Apparatus—Fig. 1 is a schematic section of the electrolysis cell used in all the current efficiency runs. The melt was contained in an iron crucible that rested on an alundum ring. A centered silica tube came within 1 in. of the surface of the melt and initially served as a thermocouple well and then as the guide for the anode.

Jan 1, 1961

By Frank Marotta, Louis B. Lesem, Frank Greytok, John J. McKetta

Although one of the primary variables in the calculation of the flowing bottom-hole pressure in gas wells from surface measurements is the temperature at any point and its distribution in the flow-string, only few experimental data are available in the literature and little attention has been given to analysis of the problem. Virtually all of the recently published methods of calculating flowing bottom-hole pressures depend on the assumption that either the temperature is constant at some average value or that the variation is linear with depth. The purposes of this work are to analyze the problem theoretically and to verify the analysis by comparison with experimental data so that practical problems in the analysis of the behavior of gas wells can be solved with greater accuracy, reliability, and ease. MATHEMATICAL OUTLINE OF PROBLEM Assuming that: 1. The mass velocity and chemical composition of the gas stream are constant and in normal gas well operations, the change in linear velocity in the entire flow-string is trivial, 2. The product of the density and heat capacity of the gas is constant, 3. No horizontal temperature gradient exists in the gas stream, 4. Net flow of heat by conduction within the formation and in the gas stream in the vertical direction is trivial in magnitude and can be neglected, 5. The regional vertical geothermal gradient is constant, and 6. The temperature of the gas entering the borehole is constant, and equal to that of the reservoir, a set of two simultaneous, linear partial differential equations with appropriate boundary conditions was derived to describe the temperature distribution in the gas stream and the surrounding formation. These equations were solved by operational techniques for the distribution of temperature in the gas stream. The resulting integrals were evaluated numerically on an IBM 604 at the Machine Accounting Div. of the Railroad Commission of Texas. DERIVATION OF FUNCTIONS FOR THE DISTRIBUTION OF TEMPERATURE The physical system is a circular hole of radius a in an infinite medium with thermal conductivity K, density p8, and heat capacity c,. Under shut-in conditions the well is in thermal equilibrium with the surroundings and the increment in temperature is given by - ?T3/L x. Gas of density pg and heat capacity c.. flows upwardly through this hole in the direction of increasing x with a linear velocity W. Writing a heat balance on an element of gas ?x in thickness, convective heat transfer + conductive heat transfer + energy required to lift a unit mass of fluid = change in energy content. pa2W po Co To - pa2Wpo Co To x+xx - 2apK?x ?T8/?r r=a - Wpa2 po?x/778 = CoPopa2?x?To/?t... Dividing by (copopa2?x) and taking the limit as ?x tends to zero, -W (?To/?x + 1/778Co) + 2 K/a Po Co ?T3/?r r=u = ?To/?t

Jan 1, 1958

By Thomas D. Henderson, Donald E. Crowell

INTRODUCTION This paper presents a "case history" of the steps taken to estimate capital and operating costs for a typical porphyry copper concentrator of ±9,070 metric tons (10,000 short tons) per day capacity. The concentrator described herein is hypothetical, but is based on experience and is, in effect, a composite of several actual projects. The numbers used are illustrative only and do not represent actual costs at any particular concentrator. These numbers are, however, representative of typical milling costs at one point in time, and. are sufficiently accurate to illustrate the cost estimating procedures described in this paper. It is not possible to publish actual, current milling costs and, in any event, actual cost figures quickly become meaningless in today&apos;s economic situation with various costs all rising at different rates. The paper is divided into three parts: (1) order-of-magnitude estimate, (2) feasibility study estimate, and (3) discussion of differences between estimated and actual costs.

Jan 1, 1978

By J. D. Prater, H. R. Spedden, E. E. Malouf

Application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production, whereas formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing so1utions.l Detailed investigations made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a precipitation cone-type recovery system having advantages over older methods.

Jan 4, 1966

By T. M. Gurr

The United States is the world&apos;s leading producer of phosphate rock. In 1975 according to the US Bureau of Mines&apos; statistics, 44.3 million tonnes (48.8 million st) of phosphate rock were produced in the United States, l which is 40.6% of the world&apos;s production.2 The major phosphate producing areas of the United States are located in [Fig. 1] and the production for 1975 is listed as follows: [ ] All of these areas produce phosphate from deposits which are of marine sedimentary origin. Occurrences of phosphate exist throughout the United States in numerous locations that are of both igneous and sedimentary origins. However, these other phosphate occurrences vary greatly in extent and economic significance. Georgia, South Carolina, California, Texas, Arkansas, Kansas, Iowa, Alabama, Kentucky, and Virginia are but a few of the states in which phosphate is thought or known to exist. The near future expansion will probably continue to be in, or near, existing producing areas, (i.e., Florida and North Carolina).

Jan 1, 1980

By David S. Butts

There are many solution mining operations that use solar ponds as a mineral recovery step. Other locations in the world are now under investigation to recover minerals by solution mining but require the cheap energy of solar ponds to make the recovery viable. This paper shows a step-by-step material balance system that can be used in both simple and complex solar ponds. Use of this system will help the engineer determine if solar ponding efficiency can be improved or if solar ponding will work at all with a given set of conditions. Even the most complicated solar pond can be reduced to six flow streams. These are (1) feed, (2) exit, (3) leakage, (4) entrainment, (5) salts, and (6) evaporation. The equations developed in this paper will allow the solar pond engineer to easily evaluate the effect of each of the flow streams on the mineral production of a pond or pond complex.

Jan 1, 1985

PRODUCTION of nonmetallic mineral raw materials used by the fertilizer, ceramic, chemical, and construction industries and many others, was greater during 1953 than in any previous year. Production of fertilizer minerals was the highest in history despite somewhat decreased consumption in the second half of the year. Marketable phosphate rock production increased 10 pct to an estimated total of 13.1 million LT, valued at $78.5 million, and potash production was estimated at 1.8 million tons of K2O equivalent, valued at over $60 million. Crude gypsum output exceeded the 1952 total and approached the record of 8.66 million tons mined in 1951, with indications that 1953 will show a new all-time high. Gains and losses among gypsum products were irregular, with major gains in plate- glass and terra-cotta plasters, sanded building plasters and miscellaneous building plasters, and principal declines in base-coat plasters, prepared finishes and tile. Lath and wallboard outputs were each about 20 pct higher than in 1952.

Jan 2, 1954

By B. Hyatt, E. Klokholm

The reesistivity of Cu-Pd alloys of 9.6 to 29 pct Pd alloys was measured after plastic deformzation in tension. For all compositions a continzting decrease in resistivity with increasing plastic strain was observed. By comparison with the results of Damask on a brass ad Cu3Au, it was deduced that these anonzalous decreases in resistivity are due to the decrease in short-vunge order caused by cold work. An anomalous decrease in the resistivity of cold-worked CU-Pd alloys was first reported by Jaumot and Sawatzky.&apos; They observed decreases in the electrical resistivity when disordered Cu-Pd alloys drawing at room temperature. Recently, a similar anomaly was reported by Aarts and Houston-Mac-Mi1lan2 in Ag-Pd alloys containing 10 to 45 pct Pd. The plastic deformation in this case was produced by tensile strain at liquid-nitrogen temperatures. For AE-Pd alloys the relative resistivity change becomes positive for tensile strains of about 20 pct.

Jan 1, 1960

Discussion of the paper of MANUEL EISSLER, presented at the New York meeting, February, 1915, and printed in Bulletin. No. 9.5, November, 1914, pp. 3661 to 2703. J. W. RICHARDS, So. Bethlehem, Pa.-I do not see in the paper a description of the Mabuki hearth as used for ore smelting. I noticed it described for concentrating matte, but I believe the older Japanese process was to use it for-smelting directly, by a pyritic smelting and Bessemerizing all in one operation, in the same simple hearth apparatus. There is a monograph published in German, on Copper-Ore Smelting in the Mabuki Hearth. At Ashio the practice of injecting bituminous coal at the, tuyères is noteworthy. It is very interesting to see two men load little cartridges on the end. of an iron rod with bituminous coal, and push them into the furnace tuyères, and with a piston inject 2 or 3 lb.. of bituminous

Jan 5, 1915

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its abbreviated title A. I. M. E. SEC. 2. The objects of this Institute, as set forth in its certificate of incorporation, are: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information thus obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of addresses, and a library of books relating to subjects cognate to the sciences and arts of mining and metallurgy."

Jan 1, 1932

NAME AND OBJECT SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Incorporated; and its abbreviated title A. I. M. E. SEC. 2. The objects of this Institute, as set forth in its certificate of incorporation, are: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information thus obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of addresses, and a library of books relating to subjects cognate to the sciences and arts of mining and metallurgy."

Jan 1, 1938

By R. W. Smith

A study has been made of the crushing and grinding circuits by the Portland Cement Association in nine cement plants. Five of the plants used the wet process and four, the dry method. Both raw and clinker grinding were studied in the four dry processing plants. The raw materials used varied considerably from plant to plant. Actual power consumption data were obtained for the majority of the grinding mills in these plants. Previously representative raw and clinker samples had been obtained from the nine plants, and Bond1 and Hardgrove2 grindability tests were run on these samples. All pertinent data concerning the grinding mills, such as mill size and speed, ball charge size and weight, size distribution of feed, and discharge materials were also obtained. Thus it became possible to calculate the actual horsepower used by the various mills, and to compare this figure to the theoretical horsepower as calculated by several different methods.

Jan 4, 1961