Search Documents

By D. R. Semmes

The possible oil territory of Alabama can be readily divided into two regions, the Paleozoic area of the north, and the Coastal Plain province of Cretaceous and younger formations lying to the south. This latter area has received much attention in the last few years and has been described by a number of writers.' Although the possibilities of the Cretaceous series have been much emphasized by recent writers, the fact remains that the two, or possibly three, localities where oil or gas have been found in anything like paying quantities are confined to the area of Carboniferous rocks. Moreover, almost all of the oil seeps and a good percentage of the gas seeps are confined to this area.2 Topographically, as well as structurally, the Paleozoic area can be divided into three rather well defined provinces: (1) The broad, open Coosa Valley lying adjacent to the crystalline oldland, with comparatively little relief, except for occasional longitudinal ridges and rather intense folding; (2) the plateau region of horizontal or gently warped Pennsylvanian strata broken by occasional anticlinal valleys aligned northeast and southwest, outliers of the Coosa Valley proper, in which the older Paleozoic formations are exposed—a region of much relief (200

Jan 1, 1921

By K. E. Brown, G. H. Fancher

An 8,000-ft experimental field well was utilized to conduct flowing pressure gradient tests under conditions of continuous, multiphase flow through 2 3/8-in. OD tubing. The well was equipped with 10 gas-lift valves and 10 Maihak electronic pressure recorders, as well as instruments to accurately measure the surface pressure, temperature, volume of injected gas and fluid production. These tests were conducted for flow rates ranging from 75 to 936 B/D at various gas-liquid ratios from 105 to 9,433 scf/bbl. An expanding-orifice gas-lift valve allowed each flow rate to be produced with a range of controlled gas-liquid ratios. From these data an accurate pressure traverse has been constructed for various flow rates and for various gas-liquid ratios. A comparison of these tests to Poettmann and Carpenter's correlation indicates that deviations occur for certain ranges of flow rates and gas-liquid ratios. Numerous curves are presented illustrating the comparison of this correlation with the field data. Poettmann and Carpenter's correlation deviates some for low flow rates and, in particular, for gas-liquid ratios in excess of 3,000 scf/bbl. These deviations me believed to be mainly due to the friction-factor correlation. However, Poettmann and Carpenter's correlation gives excellent agreement in those ranges of higher density. This was as expected and predicted by Poettmann. He pointed out that their method was not intended to be extended to those ranges of low densities whereby an extreme reversal in curvature occurs.l As a result of these experimental tests, correlations using Poettmann and Carpenter's method were established between the friction factors and mass flow rates which are applicable for all gas-liquid ratios and flow rates. Definite changing flow patterns do not allow any one correlation to be accurate for all ranges of flow. INTRODUCTION The ability to analytically predict the pressure at any point in a flow string is essential in determining optimum production string dimensions and in the design of gas-lift installations. This information is also invaluable in predicting bottom-hole pressures in flowing wells. Although this problem is not new to industry, it has by no means been solved completely for all types of flow conditions. Versluys,2 Uren, et al, 3 Gosline,4 May,5 and Moore, et al,6,7 were all early investigators of multiphase flow through vertical conduits. However, all of these investigations and proposed methods were very limited as to their range of application. Likewise, many are extremely complicated and therefore not very useful in the field. Only in the last decade have any significant methods been proposed which are generally applicable. The most widely accepted procedure in industry at the present time is a semi-empirical method developed from an energy balance, proposed by Poettmann and Carpenter8 in 1952. Their correlation is based on actual pressure measurements from field wells. Accurate predictions from this correlation are limited to high flow rates and low gas-liquid ratios. Although this method will be discussed in detail later, it should be pointed out that two important parameters, namely the gas-liquid ratio and the viscosity, were omitted in their correlation. The viscosity was justifiably omitted since their data was in the highly turbulent flow region for both phases, and most wells fall in this category. The gas-liquid ratio was incorporated to some extent in the gas-density term. In 1954, Gilbert9 presented numerous pressure gradient curves obtained from field data for various flow rates and gas-liquid ratios for the determination of optimum flow strings. However, no method is presented for predicting pressure gradients except by comparison to these curves. Baxendell, et al,10 proposed a method based on Poettmann and Carpenter's procedure

By W. L. Freyberger

In a study of the kinetics of flotation of coal, employing a single-cell continuous flotation system, Jowett and Safvi1 pointed out that it was experimentally impossible to float all of the coal which could be floated in a batch tests. On the other hand, deBruyn and Modi, in a discussion of their paper, suggested that under certain conditions the recovery of floatable material from a similar one-cell continuous system would have been 100%.2 Both of these pairs of authors make the assumption that a state of perfect mixing exist in the flotation cell. This assumption, usually made by investigators studying flotation kinetics in a continuous system, has been confirmed experimentally on several occasions. The work is summarized by Arbiter and Harris.3 It is the purpose of this note to demonstrate that, for conditions of perfect mixing, one of two conditions exist: 1) the recovery of floatable material is 100%, and the flotation is infinitely fast, or 2) the recovery of floatable material must be less than 100%. This theorem can be proved simply in the following manner: 1) If recovery, R, of the floatable material is 100%, the concentration in the tailing must be zero. This follows from the definition of recovery as

Jan 1, 1964

By Eugene S. Meieran

The effects of methods of crystal growing, wafer sawing, polishing, routine handling, diffusion, and epitaxial growth on the defects in GaAs are reviewed and studied using reflection and transmission X-ray topographic techniques. In general, it was found that boat-grown crystals exhibited fewer defects than Czochralski crystals, although all crystals showed large numbers of precipitates visible when examined in the electron microscope. Mechanical surface treatments such as sawing and mechanical polishing introduce damage to a depth of about 5 µ, most of which can be removed by suitable chemical or chem-mechanical polishing. In addition, defects can be introduced through routine handling of wafers, for example with metallic tweezers. These defects can be quite severe, and have been observed 20 µ below the wafer surface. Defects can also be introduced through diffusion and epitaxial growth. These defects, which include precipitates, growth pyramids, stacking faults, dislocations, and so forth, can be detrimental to device fabrication. It is shown that wafers or films which appear defect-free optically can contain defects visible in the X-ray topographs. WHILE the use of GaAs in the semiconductor industry has increased very rapidly in the last few years, due mainly to the recent development of many important GaAs devices,1,2 the major limit to the production of commercial quantities of many GaAs devices remains a severe lack of suitable materials technology. This lack is apparent in two critical areas. First, production quantities of high-quality GaAs crystals, reproducibly doped and precipitate-free, simply are not available commercially, although some reasonable quality material is available on a limited first-come, first-serve basis. Second, in comparison to silicon technology, little is known about the effects of processing variables on the defects either present in as-grown GaAs or introduced through processing and handling of wafers. These areas are now receiving some attention from semiconductor device manufacturers, who are studying defects in GaAs in order to better understand how either to prevent their occurrence or to cope with their existence. Most investigations of the defects in GaAs have been made by optical microscopy3-5 or transmission electron microscopy techniques.'-' Recently, however, the imaging techniques of X-ray topography, electron mi-croprobe analysis, and scanning electron microscopy are being applied to the study of GaAs.9-14 In the case of X-ray topography, a one-to-one image is obtained that must be photographically enlarged. In compensa- tion, the defects within entire wafers may be imaged by simple scanning (Lang technique15) if the wafer is reasonably perfect, or by using the scan oscillation technique developed by Schwuttke16 if the wafer is warped or distorted. The purpose of this paper is to both review and extend the general application of X-ray topographic techniques to GaAs. Emphasis will be placed on the effects of growth and process variables on the quality and perfection of both bulk and epitaxial GaAs. Reference to optical or electron microscopy results will be made when useful. Since the effects on defects of a wide variety of processing variables such as crystal growing, sawing, polishing, diffusion, and epitaxial growth will be somewhat superficially reviewed, a fairly extensive bibliography of the most important recent results in these areas is included. However, for completeness, important defects will be illustrated here, although such defects have been previously shown by others. While this paper is concerned with defects rather than with the physics of X-ray scattering, the mechanisms of contrast formation in the topographs will of necessity be briefly mentioned. EXPERIMENTAL GaAs crystals, both boat-grown18 and Czochralski-grown,'8 containing a variety of dopants of various concentrations, were purchased from outside vendors. Wafers were sliced from the crystals using a Hamco ID saw and were mechanically polished using 1 µ diamond paste. Chem-mechanical polishing was done in bromine-methanol as described by Sullivan and Kolb.18 Chemical polishing was done using a modified sulfuric-peroxide solution, 11 parts H2SO4, 1 part 30 pct H2O2, 1 part DI water.5 Zinc diffusion was carried out in a closed tube, using a 10 pct Zn-In source at 825°C for 1 hr. Oxide masking techniques were used to select the area to be diffused. Epitaxial wafers were either purchased or prepared here. All epitaxial runs prepared here were carried out using a Ga-GaAs-AsC13 source in a closed tube at a substrate temperature of 750°C. Wafers were chem-mechanically polished and gas-etched prior to deposition. The X-ray topographs were taken on a Krystallos Lang camera, operating in the transmission scanning geometry (Lang technique15) or in the reflection scanning geometry (modified Berg-Barrett technique20,21). MoKa, radiation was used for all transmission topographs using a Jarrell-Ash 100-µ spot focus. CuKal radiation was used for all reflection topographs using a General Electric CA-7 1-mm spot focus X- ray tube. Topographs were printed from an intermediate contrast inversion film, so the contrast shown in all figures here is the same as that of the original 50-µ-thick emulsion L4 Iiford nuclear plate used to record the topograph.

Jan 1, 1969

By C. J. McHargue, J. C. Ogle

Lightly deformed columbiun single crystals which contained only parallel hoins or purullel and intersecting trains were annealed at 1000' and 1600"C. No re-crystallizntion occurred in specimens hawing only parallel twins. Only noncoherent twin boundaries nzipated at 1000°C but both coherent and noncoherent ones moved al 1600°C. Recrystallization occurred within a few minutes at twin intersections at 1000°C. The orientation 01 the recrystallized grains differed front that of both the matrix and deformation twins, but could he derired by (110) and/or(112) rotations. ALTHOUGH twinning in metals has been extensively studied, there have been no definitive studies of the annealing behavior of crystals containing deformation twins. Some effects observed after annealing deformation twins have been summarized by Cahn1 and Hall2. Any or all of these phenomena are observed: 1) The twins may contract so that the sharp edges of the lens become blunted, and eventually the twin may disappear entirely. 2) The twins may balloon out at an edge, giving rise to a large grain having the same orientation as the twin. 3) The specimen may recrystallize; i.e., new grains are nucleated and grow at the expense of the twins and the crystal immediately adjoining the twin. Such grains have orientations which are not present before. Contraction has been observed in iron,3 titanium,3, 4 beryllium,5 zinc,8, 7 Fe-A1 alloy,' and uranium.9 Long anneals at high temperatures are required to have any appreciable effect in these metals and only thin twins are absorbed. Lens-shaped twins are absorbed from the edges: the thin, almost parallel-sided twins are usually punctured in several places and each piece contracts independently. Absorption is very gradual and no sudden cooperative jumps have been observed. The expansion of a twin into a larger grain of identical orientation is unusual, but such growth has been observed in iron,"'" zinc,6 and uranium." Crystals which have been deformed simultaneously by slip and twinning recrystallize first in the area adjacent to the twin. New grains appear faster where the twins intersect: but isolated twins, especially if thick, can also give rise to new grains. This type of recrystallization occurs in zinc.6, 7, 12, 13 and beryllium.14 Reed-Hill noted, in a single crystal of magnesium, the nucleation of a recrystallized grain at a twin intersection which had the same orientation as the second-order twin and which grew into the highly strained matrix.15 Short-time annealing has been reported to cause no change in the deformation twins in vanadium,16 columbium, 17, 18 tantalum,19 tungsten,'' and zinc.7 The purpose of this investigation was to note the effects of annealing on the coherent and noncoherent boundaries of deformation twins in columbium and to locate the nucleating sites for recrystallization. The orientation relationships, which the new recrystallized grains have with the parent crystal and the deformation twins, were also determined. EXPERIMENTAL PROCEDURE Single crystals of columbium were obtained by cutting large grains from electron-beam-melted buttons which contained 10 to 50 ppm C, 10 to 100 ppm O,, 1 to 10 ppm H2, and 10 to 15 ppm N2. The crystals were hand-ground and chemically polished until all grain boundaries were removed. The specimens were mounted in an epoxy resin and a face of each crystal was mechanically polished on a Syntron polisher using Linde A and then Linde B polishing compounds. After all faces were mechanically polished, the crystal was electrolytically polished to remove all distortion due to cutting and grinding. Laue photographs were taken of all faces of the crystals to determine the quality and orientation of each crystal. The crystals were compressed about 10 pct at -196 C in a specially constructed compression cage with an Instron tensile machine. Each crystal was separated from the top and bottom anvils by teflon films which acted as a lubricant. With the specimen crystal in position, the entire cage was cooled to -196°C by being submerged in a Dewar containing liquid nitrogen. The crystals were compressed at a rate of 0.02 in. per min and the load was recorded on a strip-chart recorder. After deformation the crystals were mechanically polished on 600-grit paper and Pellon cloth with Linde A and Linde B polishing compounds. The crystal faces were chemically polished and then etched. The twin planes were identified metallographically from an analysis of the twin traces on two surfaces. Annealing was carried out by placing each crystal in a columbium bucket made from the same electron-beam-melted material as the crystal itself and suspending the bucket by a tantalum wire in a quartz tube. After a vacuum of 10-7 Torr was attained, a furnace at 1000" or 1600 C was raised into position and the crystals held for various lengths of time. The crystals were repolished and etched after annealing to remove any surface contamination. Approximately 0.010 in. was removed during this process. The resulting surface was examined metallographically for microstructural changes due to annealing. A microbeam Laue camera mounted on a Hilger Micro-focus X-ray unit was used to determine the Orientstions of the recrystallized grains. This X-ray micro-beam camera had a 0.002-in.-diam collimator and incorporated the ideas of both and and chisWik21 and Cahn.22

Jan 1, 1967

By E. P. JENNINQS

(Cleveland meeting, October, 1912.) LARGE deposits of titaniferous iron-ore occur at Caribou, an old silver-mining camp in Boulder county, Colo., 17 miles west by south of Boulder, and a few miles northwest of the tungsten-mines. Professor Regis Chauvenet 1 published a part analysis of the ore many years ago, but gave no description of the wall-rock. Caribou hill, which contains both the silver-bearing veins and the iron-ore deposits, is a low dome of gabbro surrounded by the Archaean schists and gneisses of the Front range of the Rocky mountains, the peaks of which, a few miles west of Caribou, attain an elevation exceeding 12,000 ft. The gabbro stock is roughly elliptical in outline, with approximate diameters of 1 and 3 miles. The crest of the dome is 10,500 ft. above sea-level, and the town and ore-deposits are 500 ft. lower. Outcrops of the iron-ore occur in the town and extend NW. for 2,000 ft., where they disappear under the swampy meadows of Caribou park. Portions of the deposit are covered by drift, but one continuous outcrop is 900 ft. long and from 200 to 250 ft. wide. A second deposit is 0.25 mile south of the town along the eastern slope of the hill. It is not as well defined as the north bed, but is approximately 1,000 ft. long and from 100 to 200 ft. wide. The easily disintegrated ore does not form prominent outcrops, but the outlines of the deposits are readily traced by the large amount of ore fragments that cover the ground. Trenches and pits sunk on the outcrop expose a roughly banded magnetic iron-ore, with pyroxene as the principal gangue-mineral. The Gabbro. This rock was classified in the field as a gabbro from the presence of pyroxene and striated feldspars, and for convenience the field-name will be retained. 1 Chauvenet, Regis, Biennial Report of State School of Mines, Golden, Colo., p. 16 (1886).

Oct 1, 1912

By Ovid W. Eshbach

ENGINEERING education has been powerfully affected by the impact of war, just how powerfully can be better understood after considering the postwar problems regarding students, staff, and plant. In time of war no one will question the necessity of expediency of military training. With the cessation of hostilities, expediency gives way to the evolutionary process of strengthening engineering education as need is exemplified by experience. During the war, except for the Navy V-12 program, engineering education was at its lowest ebb of the century. Freshman enrollments were largely limited to those graduating from high school at the age of seventeen; and the upperclass, to those disqualified for active service. In most schools the experienced staff was either in service or government and industrial research. Many may never return to their former occupations. The most immediate problem is that of maintaining and building a staff to meet the enrollment of returning veterans. It is estimated that out of the eleven

Jan 1, 1945

By Frank T. Sisco

DURING the past year the iron and steel industry of the world as a whole operated on a satisfactory basis. No discoveries nor new processes of outstanding importance were announced either here or abroad, although rumors of such were persistent. In general, the efforts of operating and research men in the iron and steel industry seemed to be confined to improving quality and reducing cost, not a new aim, for the same efforts have been noted in nearly all of the annual reviews of the industry for at least fifty years. Most published papers on blast furnace or steel-making practice were of minor importance, at least when judged by the criterion of radical change in process or product. If the number of reports in the technical journals, or articles in the trade press, is used as a basis for comparison, continuous-mill sheet is still the most important single product of the industry; papers were published detailing the results of the investigation of various phases of the

Jan 1, 1938

By J. W. Sandelin, L. S. Birks

The group five metals, vanadium, niobium, and tantalum all show cold-rolled textures of {100)(011) and {112)(0ll) with a preference for the (100) in vanadium and niobium and for the {112) in tantalum. Recrys-tallization texture of (100) and (111) was reported1 for vanadium after annealing (no temperature stated). For tantal~m ,~ annealing below 1200°C strengthened the (112) texture but the (111) texture increased and was predominant as the annealing temperature was raised to 2500°C. Annealing niobium up to 1100°C strengthened the ( 100) texture and developed a weak (111) texture.' In the present work niobium has been annealed up to 2000°C. Nearly 70 pct of the grains showed {111) texture with only a weak (112) component and an insignificant (100) component remaining. In addition, double-crystal rocking curves were used to follow the increase in crystal perfection of the grains with increased annealing time. Material and Treatment. Samples i by 4 in. were sawed from & -in.-thick cold-rolled niobium sheet obtained from Wah Chang. Chemical analysis of the material showed it to be 99.4 pct pure with tantalum as the major impurity. Individual pieces were annealed for 2, 15, 30, and 60 rnin in a vacuum of 10'* Torr using an rf generator. They were etched until the grain boundaries were well-defined, Fig. 1. Average grain size varied from 1 mm for 2 min annealing to 2 mm for 60 rnin annealing. Experimental Results. Preferred Orientation. The orientations of 97 of the 117 grains in the specimens of Fig. 1 were determined by back-reflect ion Laue patterns. A General Electric 10-cm-diam cylindrical camera was used rather than the conventional flat camera in order to record more of the low-index spots. The method proposed by Forest, Barton, and schieltz4 was used to transform the cylindrical film patterns to standard stereographic projections. Table I gives the compilation of data. Even 2 rnin anneal at 2000°C is sufficient to yield a strong (111) preferred orientation, and the percentage of grains with this orientation increases steadily with annealing time at the expense of all other orientations. Crystal Perfection. X-ray topographs were taken of each specimen in both the (111) and (112) orientation using the method described by Birks and Grant.' As the anneal time increases, the grains become larger and the individual reflections become slightly more uniform in intensity, indicating an increase in crystal perfection. For a more quantitative measure of crystal perfection, it was necessary to measure the double-crystal rocking curve. The spectrometer employed was a Gaertner instrument of Compton design. LiF was chosen for the first crystal because the (400) reflection with d spacing of 1.05 AU is a good match to the (222) niobium reflection with d spacing of 0.95 AU. CuKp radiation was used in order to further reduce the d spacing mixmatch correction.' A variable aperture was placed between the LiF and the niobium specimen so that a single grain or even a small portion of a grain could be examined. Fig. 2 shows typical rocking curves for the four annealing times. For the 2-min specimen, a single peak is observed with 10' of arc full-breadth at half maximum. As the annealing time is increased to 15 or 30 min, several sharper peaks of 40 to 80" breadth can be seen within a single grain. After 60 rnin anneal only a single peak of about 30" is observed. Table I1 shows the corrected rocking curve breadths and the dislocation densities, ND. The latter were calculated from the equation7 where W is the corrected rocking curve breadth at half maximum in radians and b is the effective Burger's vector. For (110)(111) slip in niobium, b is 2.86 AU. Discussion. The annealing of cold-rolled niobium at 2000°C causes rapid preferential growth of grains with {ill} orientation. After only 2 rnin annealing time, 35 pct of the grains have the (111) orientation, and after

Jan 1, 1968

By Arnulf Muan, W. C. Hahn

Activities of "FeO" in "FeO"-MgO solid solutions have been determined in the temperature interval 1100" to 1300"C by equilibrating oxide samples with pure metallic iron in atmospheres of known oxygen partial pressures. The end members "FeO" and MgO form a complete solid solution series. The system shoztls a considerable positive deviation from Raoult's law. A large amount of data has been accumulated during the past 50 years on stability relations existing among various crystalline and liquid phases in oxide systems of importance in metallurgical processes. By comparison, very little is known about the thermodynamic properties within the various homogeneous phases present in the systems, particularly the crystalline phases. The present paper deals with determination of activities as a function of composition in solid solutions of wüstite ("FeO") and periclase (MgO). Such solid solutions ("Magnesiowustites") have simple sodium chloride structure and are known to be continuous between the end members at elevated temperatures (> 1000°C) and strongly reducing conditions such as prevail in contact with metallic iron. Wiistite has a defect structure in which the ratio of oxygen to iron varies and never has as low a value as 1:1 corresponding to the simplified formula FeO. Within the range of stability of this phase, the composition changes between a maximum oxygen content of approximately 25.6 wt pct (corresponding to the formula FeO.83O) and a minimum oxygen content of approximately 23.2 wt pct (corresponding to the formula Fe0-96O). The activity data to be reported in the present paper are based on using as standard state the wüstite which is in equilibrium with metallic iron at a particular temperature, i.e., "FeO" of minimum oxygen content at each temperature. For sake of simplicity, the formula FeO will be used to represent the wustite phase in the remainder of this paper. Consider the reaction 2 FeO solid solution = 2 Femeta1 + Ozgas in which FeO dissolved in another oxide dissociates to metal and gas. The activity of FeO in the solid solution, relative to "pure FeO" in equilibrium with metallic iron as a standard state, is then expressed as Here Po, and po2 * are the partial pressures of oxygen of the gas phase in equilibrium with metallic iron and the oxide solid solution or "pure FeO", respectively. The equation holds only if the metal phase is essentially pure Fe. The oxide combinations used in the present investigation fulfill this requirement. Magnesia is so much more stable than FeO that for all practical purposes aFe = 1 in the metal phase present in all mixtures used in this investigation. I. EXPERIMENTAL METHOD 1. General Procedure. The experimental method used was analogous to that developed by Foster and Welch1 and used recently by Hahn and Muan.2 It consisted of four steps: a) Determination of the equilibrium between FeO and Fe. b) Determination of d-spacing change with composition in oxide solid solutions (FeO-WO). c) Equilibration of various members of the solid solution series with a metal phase and a gas phase of known oxygen partial pressure. d) Determination of compositions of solid solutions resulting from step (c) by means of data obtained in step (b). 2. Starting Materials. General Aniline and Film Corp. carbonyl iron powder, type HP, was used as the source of metallic iron. A representative analysis was as follows: Fe, 99.6 pct; C, 0.01 to 0.04 pct; 0, 0.1 to 0.3 pct; N, 0.00 to 0.05 pct. Other elements were present as traces only. Wiistite was prepared from "Baker Analyzed" Reagent grade Fe2O3 of reported analysis as follows: Assay (Fe2O3), 98.8 pct; insoluble in HC1, 0.02 pct; not precipitated by NH,OH, 0.02 pct; Zn, 0.003 pct. Production of wüstite was achieved by a two-step

Jan 1, 1962

By W. A. Backofen, B. B. Hundy

THE pole figure interpretation in a recent paper' on the torsion texture of copper was questioned in discussion,2 nd a simpler alternative interpretation was proposed. In the hope of reaching a positive decision in favor of one or the other, further studies were undertaken with 70-30 brass and Armco iron. This additional work has not answered all the questions about torsion textures, but the new pole figures do offer support for the original interpretation and show that the texture is more complicated than the alternative suggests. From the previous paper,' the appropriate method of describing the texture in a twisted bar is known to be a pole figure plotted on a plane tangent to the surface of the bar. The axes of the pole figure are chosen to coincide with directions in the tangent plane which are parallel and at right angles to the bar axis (the longitudinal direction, L.D., and the transverse direction, T.D.), for these directions define symmetry axes of the texture. Therefore any ideal orientation that might be selected to represent the texture gives the crystallographic plane parallel to the tangent plane and the crystallographic direction parallel to the axis of the torsion specimen. A unique texture was assumed in the original interpretation, and the four ideal orientations, (112) [111], (111) [112], (110) [001], and (112) [131], were used in its description. Of the four orientations, the first three provide possible slip directions along the direction labeled T.D. in the pole figure, which is one of maximum shear stress in a specimen being twisted. The alternative, however, simply considered the texture to be made up of two components, one a [Ill] alignment along the specimen axis with a random orientation about the axis as in the wire texture, and the other a superimposed orientation (110) [0011. Experimental evidence for this simpler interpretation was derived from two observations: 1—twisting did not alter the orientation of a single-crystal torsion specimen of a brass in which an octahedral plane was perpendicular (and a [Ill] direction parallel) to the axis, and 2—deformation bands with approximately the (110) [001] orientation were seen to develop in the crystal during the test. The new pole figures were obtained with a brass and an iron torsion specimen of 3/4 and 1 in. gage length diameter, respectively. After annealing, polishing, and twisting, seven rods, about 0.030 in. in diameter and with different orientations, were prepared from material near the surface of each specimen; these were required for the method of constructing pole figures by using a Geiger counter as developed by Norton.5 Since the shear strain gradient in plastic torsion is linear, it was readily computed that the material supplying the brass rods had been subjected to a shear strain of about 3.2, and that supplying the iron rods had received a shear strain of about 2. All details concerning specimen design, testing procedure, rod preparation, and use of the Norton technique can be found in ref. 1. Only this procedure was followed in working out the (111) and (100) pole figures for brass, Figs. 1 and 2. However, X-ray photograms were also involved in the construction of the (110) pole figure for Armco iron, Fig. 3. The photograms were made according to the conventional transmission diffraction technique using a small sheet taken parallel to the specimen surface and etched to a thickness of about 0.0025 in. They were especially important in locating the boundaries

Jan 1, 1954

By U. F. Kocks

SINGLE slip and a single parallel array of edge dislocations have been obtained in silicon single crystals by homogeneously bending them in a four-point dead-loading device at 1000°C around the [211] axis with [253.] as the tensile axis which encloses an angle of 40° with the glide plane. Other orientations or lower temperatures proved unsuitable. The homogeneity of the bending was checked by the method shown in Fig. 1. The chemically polished specimen was exposed to parallel light from a microscope-stage lamp. The sharpness of the focus of the reflected light is an approximate measure of the circularity of the sample. This method permitted the determination of the actual radius of bent specimens within 10 pct accuracy. The etching solution developed to show up dislocations consisted of the following volume parts: 2 HF, 1 HNO,, 2 CH,COOH, 1 a solution of 5 wt pct of CuNO, in water (Rosi'). The acetic-acid content was adjusted to produce fine well-defined etch-pits in about 2 min at room temperature. The effectiveness of the etch did not depend on the crystal-lographic orientation of the face etched. The number of etch pits produced after a given deformation was checked in the usual way against the Cahn formula' and showed good agreement. As it is to be expected from the orientation of the primary system there are slip steps on the top and bottom faces but not on the side faces (perpendicular to the bending axis), whereas etch pits appear on the side faces but not on the top and bottom faces. This is different only for occasional dislocations of a secondary glide system. All the micrographs included have been taken in places where the most of secondary glide could be seen. From this it is evident that in the homegeneously deformed region the number of secondary dislocations was less than 1 in 1000 of the primary type. Dislocation Distribution—A series of tests with varying amounts of deformation is shown in Figs. 2(a-c). An observation that can readily be made from these pictures is that the linear density of dislocations within slip lines is relatively constant and independent of the amount of deformation. "Slip line" in this context is understood to mean a line that is a straight connection of individual etch pits. The heavily pitted bands which can be seen in each of these three pictures may be resolved fairly definitely, at higher magnifications, into many "slip lines" the distance between them being of the order of 0.5p The distance between dislocations in slip lines is of the order of 2p and it is also fairly constant in going from the neutral zone outward. The higher over-all dislocation density in the outer regions of any sample and the higher total number in a more heavily deformed sample, are effected by a larger number of "slip lines." The relative constancy of the dislocation distance within an individual slip line is surprising. The absence of pile-ups" may imply, if there is no rear- rangement on unloading," that there are no substantial obstacles to slip in this case. It seems that the equilibrium distribution of the dislocations in each active slip plane under the higher external stress on

Jan 1, 1959

By W. F. Wheeler

A discussion of the paper of W. F. Wheeler, presented at the Toronto Meeting, July, 1907 (Trans., xxxviii., 621 to 632). A. BEMENT, Chicago, Ill. (communication to the Secretary*):¬Formerly it was the general practice of engineers to designate coal that is free from moisture and ash as " combustible,", not-withstanding that it contains oxygen and nitrogen. The origin of this practice was more particularly due to the requirements in connection with boiler-testing, which demanded a consideration of that portion of the fuel which took part in the combustion-process because results based on a unit of either moist or dry coal were not comparable, since both moisture and ash were recognized as variable quantities. Thus, a pound of " combustible " became a standard of value, and was treated as a constant before employing measurements of heating-power and calculating therefrom the percentage of efficiency. The recognition of this term ." combustible" was an advance to be credited to the engineer .rather than to the chemist, because the latter, not having to do with the interpretation of analysis in practice outside the laboratory, usually saw no reason for reporting results in terms other than those of the moist-coal composition. Some years ago I needed a table of fuel-composition in terms of moist, dry, moisture-free and ash-free coal, and of the combustible components. This table required the use of the word combustible in its proper sense, for the purpose of designating carbon, hydrogen, and sulphur, instead of including these three elements with oxygen and nitrogen, to which aggregate the term combustible was formerly applied. To make such a tabulation involved either the use of the inconvenient and cumbersome term, "ash and moisture-free coal," or of some other representative term, and for this purpose I adopted the expression " pure coal," which is short, simple, convenient, and technically correct. It is also harmonious, because it agrees

Sep 1, 1908

By J. J. Mike

During the past few years the combination of continuous billet casting with in-line reduction has been studied and several machines have been built with this capability included in the design parameters. (1,2,3,4,5) In-line reduction and continuous casting in combination are obvious and attractive. As pinch rolls are already in place for the continuous casting operation, it can be readily seen that a redesign of the mechanical and electrical equipment of the pinch rolls is all that is necessary to have in-line rolling. There have been numerous in-line reduction experiments conducted by simply increasing the pinch roll pressure on existing machines. (6,7,8,9) These generally failed to produce quality billets and often resulted in internal metallurgical defects (Figure 1).

Jan 1, 1972

By Herbert Clark Hoover, Lou Henry Hoover

MANY persons hold the opinion that the metal industries are fortuitous and that the occupation is one of sordid toil, and altogether a kind of business requiring not so much skill as labour. But as for myself, when I reflect carefully upon its special points one by one, it appears to be far otherwise. For a miner must have the greatest skill in his work, that he may know first of all what mountain or hill, what valley or plain, can be prospected most profitably, or what he should leave alone ; moreover, he must understand the veins, stringers1 and seams in the rocks2. Then he must be thoroughly familiar with the many and varied species of earths, juices3, gems, stones, marbles, rocks, metals, and compounds4. He must also have a

Jan 1, 1950

By Marvin P. Barnes

The Sacaton open pit copper mine has recently been placed into production. Some problems have been encountered in maintaining grade control due to differences between early block estimates and actual production grade. A study was made using three methods for computing grade for 50' x 50' x 40' size blocks from exploration and development drill holes; 1) The polygonal method, 2) The inverse distance squared method, and 3) The geostatistical kriging method. The results of each were compared against a control block file created by using the assay results of all blast holes drilled in the ore over three benches of the new pit. Results indicate that the kriging technique gave better estimates for grade of individual blocks than did the other two methods for this particular deposit.

Jan 1, 1977

By Richard W. Greene, Joel S. Hirschhorn

MATERIALS containing very large amounts of porosity, in the order of 50 to 90 vol pct, are extremely difficult to evaluate according to conventional mechanical behavior tests. This is usually a consequence of their low strength and brittleness, and the difficulty of preparing standard test specimens. A simple fatigue test has been developed and used successfully on porous nickel sheet materials requiring no specimen preparation; it could also be used for configurations other than sheet or plate. Samples of the sheet. 2 in. sq and about 0.025 in. thick, are placed in a vessel that is evacuated to about 50 f Hg by a mechanical pump. Distilled and deairated water is allowed to enter the vessel thereby filling the porosity (virtually all the porosity in these nickel ma-

Jan 1, 1970

By F. R. Hensel

THE demand for clean steel is increasing daily. New processes of refining steel are being developed in order to remove all nonmetallic inclusions as completely as possible, as it is the general opinion that. inclusions affect the dynamic properties of steel and iron to such an extent as to justify great expense for their removal. It is surprising to note at the same time the commercial development of a new process for making artificial wrought iron. By this process slag and steel are thoroughly mixed, the amount of nonmetallic inclusions usually exceeding 2 per cent in weight. The contradiction in these two efforts is obvious and is responsible for the investigation reported in this paper. H. W. Gillett also has recently emphasized the need for further research on wrought iron.1

Jan 1, 1932

The first of the two fall meetings of the Petroleum Division was held at Los Angeles, Oct 1-2 The attendance was the largest at a Coast meeting of the Division The Institute was officially represented by President Lovejoy, Secretary Parsons and George Otis Smith There were four sessions Thursday afternoon and evening, the latter a dinner meeting (both at the University Club), and Friday morning and after- noon, these two in the auditorium of the Edison building Possibly a dozen papers were presented, all of them constituting a valuable contribution to petroleum technology Hallan N Marsh, Chairman of the Division, presided at the dinner meeting at which Dr Smith addressed the members on "The Kettleman Plan m Retrospect," and C M Nickerson talked on the "Buena Vista Hills Cooperative Development Plan "

Jan 1, 1937

By William R. Chedsey

ALTHOUGH few changes can be reported in educational methods at the mineral technology schools during 1940, other events have taken place of direct interest to, and that will have a profound effect upon, mineral industry education on the United States. In the erection of new buildings, some notable changes have been made on the campus, The U.S. Bureau of Mines Experiment Station at the University of Utah, Salt Lake City, was dedicated on May 20. The construction and equipment of this building cost between $300,000 and $400,000. It will be the general headquarters for the metallurgical division of the Bureau and will have a pronounced effect upon the mineral industries research program at the University.

Jan 1, 1941