Search Documents

By C. E. Melbye

A serious problem confronted the city of Gunnison early in 1958 in that, for a few months during each spring runoff, the water supply derived from the Gunnison River became polluted to an unsafe point. The city management had the choice of building a new filter plant to replace the old unworkable one or drilling wells to develop a ground water supply. The cost of a new filter plant was estimated at $180,000 compared to $50,000 for 6 wells, pumps, and additional water lines, hence their decision to attempt the development of sufficient ground water. Six wells at 300 gpm per well were estimated as necessary to handle the peak usage of 1800 gpm, compared to only 600 gpm winter usage. Although the water table is only about 7 feet below the surface, existing private wells drilled at random locations were producing much less than 300 gpm. The problem was to find sufficient quantities from about 6 wells. Since the presence of an ancient bedrock channel was suspected, which would be expected to localize greater quantities of water, the city of Gunnison authorized a resistivity survey to investigate bedrock topography below unconsolidated gravels. Survey results were highly satisfactory and led to the preparation of a fairly detailed bedrock contour map, Fig. 1. This map was used in selection of all well sites. The city of Gunnison is situated in a flat, broad, Quaternary gravel-filled valley (terrain dips south at 20 feet per mile) at the junction of the Gunnison River and Tomichi Creek. The valley, about 2-4 miles wide, is bordered by hills of Tertiary volcanics to the northwest, Cretaceous and Jurassic sediments to the north and northeast, and pre-Cambrian granite and gneiss to the south. One previous deep test well at the west end of the city hit pre-Cambrian granite at 496 feet, which, allowing for 40 feet of surface gravels, makes the older sedimentary section 456 feet thick. This section is probably all Jurassic Morrison formation, consisting of the Saltwash sandstone overlain by the much thicker section of Brushy Basin shales and mudstones. According to the driller's logs, each well was bottomed in what is believed to be Brushy Basin shale. FIELD PROCEDURE A standard Gish-Rooney type of resistivity apparatus was employed, which used 45-volt dry batteries as a direct-current power source. Applied voltages could be selected from 45 volts to a 270-volt maximum. Copper-coated steel stakes were employed as current electrodes and porous porcelain pots as potential electrodes to avoid possible polarization effects with direct current. The expanding Wenner electrode configuration was utilized for this investigation and measurements were made at 20 40, 60, 80, and 100-foot spacings,

Jan 1, 1961

By James P. Kimball

AMONG the curious results of the recent advance of prices in the iron trade of the United States, one of them at least is to be regarded as of great importance. I allude to the utilization of mill cinder as a cheap and almost costless substitute for high-priced iron ores in many blast furnaces, situated within easy reach of such raw material. It has been, with but few exceptions, the practice in this country, based upon tradition rather than upon authority or European precedents, to waste this material on 'account of its high proportion of silicic and phosphoric acids, although known to contain more iron than most ores, and although also known to be sometimes applied to the blast furnace in greater or less quantities without serious detriment to the iron for specific purposes. While in use to a limited extent in the Hocking Valley and Hanging Rock iron regions of Ohio for several years, its use in Western Pennsylvania has only become general of late, under the exigencies of high prices and a short supply of ore. Especially has mill cinder largely entered into the stock of furnaces attached to rolling mills in and about Pittsburgh. Under such circumstances the cinder pig has been paddled on the premises, and the malleable iron produced has been unexpectedly good. Cautiously as at first mill cinder has been applied, it is evident that the temptation to use it freely is a strong one whenever the commercial rates for high-class ores are out of proportion to the general conditions of the iron trade, as sometimes happens in this country, especially as the free use of it is apparently justified by the quality of the iron produced from this cheap and abundant material. Indeed the consumption of cinder pig has., not been wholly confined to mills using up the production of furnaces belonging to the same plant. One furnace at least on the Ohio, at Covington, for several' months has been making foundry pig from "all cinder." The iron has gone into the general trade. It is probable that malleable iron of good quality can he made from the poorest cinder pig, but with what degree of economy will

Jan 1, 1881

By L. F. Pett

ALTHOUGH Kennecott's orebody has long been outlined, it is still necessary to define further its limits. This mine, long an advocate of churn drill methods, recently supplemented its practice by using a diamond drill. So far, the diamond drill holes have been along the main canyon floor which traverses the mine area. This zone, highly fractured, is cut by numerous friable quartz veinlets encountered within the porphyry. These veinlets, formed by filling contracted porphyry fractures with hot, siliceous, mineral-bearing solutions, are often more highly mineralized than adjacent porphyry. They pulverize on contact, yielding only slight amounts of core. For this reason neither analysis of core recovered (amounting to 37.5 pct of approximately 10,000 ft of hole drilled) nor sludge analysis considered separately would give correct assays. The following equation has been adopted: actual weight theoretical actual weight core — theoretical weight sludge Drilling is done un.der contract. Collection of core and sludge samples together with double-checked assaying is done by the company. Microscopic, specto-graphic, and X-ray examination of rock specimen saved is carried on at the University of Utah. A fund, set up by Kennecott Copper Corp. at the University, has encouraged cooperation in solution of mining research problems. The drill used is a Longyear hydraulic powered by a Waukesha 26-hp gasoline motor. A pump, Bean Royal type, is powered by a 7-hp Briggs-Stratton gasoline motor. Weight of unit is 4000 lb and is placed under tripod of 35-ft wood poles within a 25-ft sq area. The following results have been attained: Avg depth of hole drilled, ft 1215 Avg drilling depth per 8-hr shift, ft 10.11 Core Size, In. Avg depth of NC casing, ft 21 2 11/16 Avg depth of NX casing and size core, ft 178 2Ye Avg depth of BX casing and size core. ft 427 1% Avg depth of AX casing and size core, ft 585 1 5/32 Through the use of metal sludge collection boxes, 12 ft long, 18 in. wide, and varying from 12 to 24 in. in depth, sludge recovery has been maintained above 95 pct. Samples, both core and sludge, are assembled for each sample interval and averaged in 50-ft bench increments. Determinations for mineral values are made at both the mine and mill. Assay results varying in excess of 0.05 of copper assay values are rerun to determine correct assay. The organization chart for the Kennecott Utah copper mine is shown in Fig. 1. The Utah mine requires approximately four men per shovel shift to drill solid rock, properly slope banks, and trim loose material from the top of bench sections in making them safe for men and equipment working below. During recent years, while the mine has been worked day and night, powder crews have worked day shift only. Series of toe holes drilled back of advancing electric shovels comprise approximately 70 pct of all mine drilling. These holes, spaced about 21 ft apart, have a depth of 24 ft. Of the footage drilled, 25 pct is for vertical holes either 24 or 28 ft deep, spaced about 28 ft centers along the top rim of banks. This combination of toe holes, using an Ingersol-Rand DA 35 drifter mounted on a tripod and the vertical holes using an Ingersol-Rand Type X71 wagon drill is standard practice above the pit elevation. These benches are 68 ft high, with a few exceptions, while benches below the pit elevation are 50 ft high and require very little drilling other than toe holes. Five benches, varying in height from 80 to 100 ft, require a combination of toe holes plus vertical holes and bank holes or electric churn drill holes. Bank holes using the DA 35 drifter and electric churn drill using Bucyrus-Erie Model 29T, account for 5 pct of feet drilled. Until the past year, drilling of fill material on upper levels was accomplished by churn drill method. Wagon drills are now used for fills because they can be set up and drill a hole an hour. It is necessary to run an air drill 7 hr for each 8-hr shovel shift. Average drilling rates during the past year were as follows: DA 35 drifter using 2 and 3-man crews — 4.36 ft per man hr X 71 wagon drill using 2-man crews — 6.45 ft per man hr DA 35 drifter bank holes, 3-man crews — 2.53 ft per man hr Bucyrus-Erie churn drill, 2-man crews —1.9 ft per man hr Total mine avg — 4.57 ft per man hr Mine practice assigns powdermen to job locations where they perform all drilling and blasting work within the area. Almost as much labor is consumed in springing and loading holes as in drilling them. Average powder consumption is approximately as follows: Per Electric Shovel Shift, Lb To spring and chamber holes — 50 Blasting — 500 Trim banks — 50 One fifth of all powder used is Hercules hercomite bag powder while four fifths is Hercules gelamite 65 pct strength in 1 Vi in. x 8 in. sticks. Frozen material, overhanging from top banks, creates a winter hazard to shovel operators and equipment. Experiments are being conducted with a high-speed Hercules powder in an effort to eliminate this condition. Banks are trimmed by powdermen who lodge 8 or 10 bundles of powder, containing 15 or 20 sticks each, across the upper surfaces of each working face. To each bundle of powder is attached a primer with 6-ft fuse which is lighted as the powdermen, who have lowered themselves down the bank on ropes, ascend to safety. Three angle dozers, D8 caterpillars, make grades and move supplies for the average 31 drilling machines working daily. Compressed air is furnished by three Ingersol-Rand compressors, each with rated capacity of 3750 cu ft of air per min at 100 lb reservoir pressure.

Jan 1, 1952

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By H. Kazemi, G. W. Thomas, M. S. Seth

The double-porosity model of Warren and Root7 for examining pressure drawdown and buildup phenomena in naturally fractured reservoirs has been extended to intetpret interference test results. Both analytical and numerical solutions are presented. The practicality of some of the assumptions in the Warren-Root model was also investigated. The standard procedure for interpreting interference tests in naturally fractured reservoirs beretofore employed an equivalent homogeneous reservoir model. A comparison of our results with the equivalent homogeneous model indicates the latter is inadequate for early time responses. For late time responses, however, the simpler equivalent homogeneous model yields favorable results. Finally, the effects of well spacing and the magnitude of the interporosity flow parameter are briefly cited. INTRODUCTION Interference tests can be used to provide reservoir information not obtainable from conventional pressure drawdown and buildup tests. The technique involves measuring the response in one or more wells arising from a pressure perturbation introduced into another well. It has been. successfully applied to single-layer, homogeneous, unfractured, isotropic and anisotropic formations to arrive at values of well storage capacity and a measure of directional permeability.l The techniques of interference testing usually can be extended to heterogeneous systems, provided the permeability contrast between any existing rock layers is not excessive.9 In such cases, the practical interference effects in an observation well of an interconnecting heterogeneous reservoir can be predicted using an equivalent homogeneous model. The calculated properties are then average values. Russell and Prats2 have demonstrated the utility of this approach for a single-phase, two-layer system. For naturally fractured reservoirs, some different approaches usually are necessary. The major departure from homogeneous or nearly homogeneous reservoir treatment is to characterize the fractured system as an entity having "double-porosity"; namely, we suppose the existence of both primary and secondary porosity, where the former is contained within a systematic array of identical rectangular matrix blocks and the latter is contained within an orthogonal system of continuous, uniform fractures (see Fig. 1). It is sufficient to assume that the permeability of the rock matrix is so small that movement of reservoir fluids to the producing wells is entirely through the fracture network. This assumption has been validated by Barenblatt3 and .employed by others?-7 Warren and Root7 used the double-porosity model to develop an interpretation of pressure drawdown and pressure buildup tests in naturally fractured

Jan 1, 1970

By Enrique Touceda

FOR a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At -the outbreak of the war the firm decided to specialize in the manufacture f propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods f manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual -blade mold formed, the pattern is then rotated on the spindle to the position- for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this practice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface f each blade must be chipped too the templet and through this procedure chipped to such accuracy, as will be required for a static balance. Inasmuch as the' work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin f the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days f foundry work and about the same length of, time for the machining. Through the use f the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity, with any particular propeller-wheel design,

Jan 4, 1921

By Rudolph Emmel

THE mines operated by the South American Development Co. are located in the Zaruma mining district of southwestern Ecuador. They are near the old mining town of Zaruma, which is the only important city in the canton of the same name. The district is situated in the upper end of a valley lying between two spurs of the Cordillera, one of which may be considered the Coast Range and the other an intermediate range. The mining camp proper, known as Portovelo, and the plant are 2.4 km. south of Zaruma, on the north bank of the Amarillo River, a tributary of the Tumbes River, which flows southwestward through Peru to the Pacific. Portovelo is difficult of access; it is reached from Guayaquil by means of river steamers and muleback. Embarking at Guayaquil, the route is down the Guayas River, across the Jambeli Canal, and up the Santa Rosa River to Santa Rosa, a distance of 177 km. From Santa Rosa, the road or trail follows the Santa Rosa River, then across the summit of the Coast Range into Portovelo, a distance of 74 km.-a two-day trip on muleback. The mining property of the South American Development Co. comprises 297 lode claims and 142 placer claims. The combined lode claims cover an area, roughly rectangular in shape, 9000 m. long from north to south by 4000 m. wide; the northern edge of the rectangle is about 3000 m. north of the central plaza of Zaruma. Mineral lands in Ecuador are held by virtue of an annual tax per claim paid to the central government, no surface rights being included.

Jan 1, 1925

By L. F. Reinartz

ANOTHER year has rolled by. We are twelve months further away from the start of the depression and. therefore that much nearer to recovery. The accumulated needs and wants 'of our lame, virile population are ready to burst their bonds as soon as confidence returns and credit is stabilized. The steel industry has been harassed by uncertainty of the Government's attitude toward organized labor's de¬mands, and irregularity in volume of production. Steel labor, if left to its own devices, would in most instances, march shoulder to shoulder with the management of steel plants in their effort to pull the industry nut of the ?red.? Cooperation between management and men has improved considerably during; the year.

Jan 1, 1935

By A. Moskowitz, L. S. Redmerski

The corrosion resistance of stainless steels can be strongly affected by surface treatments. Changes in corrosion resistance can relate to surface composition, integrity and stability of the passive film, and to surface profile (roughness). Operations producing oxidation at the surface, such as annealing, heat treating, and welding, can result in a chromium-rich scale and a chromium-depleted metal surface. In order to restore full corrosion resistance, chemical or mechanical clean-up techniques must remove not only the oxide, but also a very thin layer of metal. Laboratory and field test studies show that these factors are particularly significant in less highly alloyed steels. Annealing stainless in a reducing atmosphere (bright annealing) avoids chromium depletion, but as-bright-annealed material does not display optimum corrosion resistance in certain environments. Electro passiva-tion can be applied to improve pitting resistance without significantly changing bright surface appearance. Potentiometric studies show that electropassivated material also displays significantly greater resistance to breakdown of passivity in acid solutions. The application of special surface finishes for appearance purposes can affect corrosion resistance. Roughness is a key factor. Samples of related appearance but with different surface profiles can show significant differences in corrosion resistance. Thus nonreflec-tive stainless with a relatively smooth surface produced by a special rolling process is much superior to material chemically etched to a similar low reflectivity. THE corrosion resistance of a stainless steel is affected by other factors in addition to its bulk composition and metallurgical structure. These other factors include those relating to the specific chemical and physical condition of the steel's surface. This paper will consider certain aspects of surface condition in relation to corrosion resistance. In particular, studies will be described on the effects of oxidation encountered in heat treating or welding operations, of passivation after bright annealing, and of different surface finishes. EFFECTS DUE TO OXIDATION When stainless steels are exposed to high temperature in an oxidizing environment, as in annealing or welding, the oxides formed are relatively rich in chromium. As a consequence of oxidation, the metallic layer directly beneath the scale may be low in chromium to some very thin but finite depth.1"8 Such a change in chromium content could lower the corrosion resistance at the surface, whether or not the oxide layer is removed. Studies were performed relating to the effect of oxidation and chromium depletion produced during annealing and welding on the corrosion resistance of stainless steels. The nominal compositions of steels used in this study and others are given in Table I. A) Annealing Studies on 17 pet Cr Steels. 1) Effects of Pickling Treatments. Studies were performed to investigate the corrosion resistance of air annealed type 430 stainless as a function of the amount of electrolytic pickling after annealing. The material used in this study had been air annealed and electrolytically pickled in the mill. All scale had been removed, and yet the material showed unusually poor corrosion resistance. Laboratory electrolytic pickling studies were performed to determine whether additional metal removal from the surface would improve corrosion resistance. Electrolytic pickling was performed in a sulfuric acid bath using various conditions of bath acidity, temperature, time, and current density. The samples were then rated for corrosion resistance in a ferric chloride spot test. For this spot test, a solution was prepared by dissolving 10 g of FeCl3 . 6H2O, 5 g of NaCl, and 2.5 ml of concentrated HC1 in 200 ml of water. An area on a specimen was cleaned and a drop of test solution was placed on the prepared area. After 5 min, the drop was rinsed off and the area wiped dry. The spot was then rated between 1 and 5 by visual comparison with standard spots. The numerical rating of the standard spots can be described as follows: 1—No clouding of surface; 2—very slight clouding of surface; 3—slight clouding of surface; 4—moderate clouding of surface; 5—strong clouding of surface. A rating of 1 or 2 was considered to have passed the test, a rating of 4 or 5 represented failure, and a rating of 3 was considered borderline. The severity of etching in this test has been related to the actual chromium content at the surface.4 Etching (clouding) occurs on type 430 stainless (rating of 4 to 5) when the surface chromium content is 14 pct or less. The effects of current density and retention time when electrolytically repickling this material in 6 pct sulfuric acid are shown in Fig. 1. Increasing the cur-rent density or retention time improved corrosion resistance as measured by the spot test. Similarly, increasing acid concentration of the bath or bath tem-perature was found to improve corrosion resistance. The conditions making for improved spot ratings resulted in increased metal removal, regardless of specific pickling conditions used, Fig. 2.

Jan 1, 1970

By William R. Jones, Robert M. Hernon

This report on the Central mining district of New Mexico is the partial culmination of an intensive U.S. Geological Survey effort dating back some 30 years. Robert M. Hernon went to Silver City in 1948 to finish a detailed restudy of the district that had been started in the thirties by Samuel G. Lasky. He was joined by William R. Jones in 1951, and Jones took over as project chief when Hernon resigned to do consulting work in 1953; it was under Jones' guidance that most of the work was brought to completion or nearly so ( 17, 22-24, 26-30). Hernon returned to the Survey in 1958 to work in .the southern Appalachians. Early in 1965 Jones urged that Hernon be reassigned to the Silver City project to help complete the Professional Paper report on the ore deposits of the Santa Rita quadrangle as well as to take over preparation of the report on the Central district for the Graton-Sales volume. This reassignment was approved, and Hernon began work on the present report. By late June he had completed most of it in draft form, and on June 28 Jones and Hernon left Denver for a short trip to Silver City to fill in a few gaps and to reacquaint Hernon with activities in the district, which he had not visited for 12 years. Late in the afternoon of June 29, 1965, as Bob and Bill were 85 miles short of their destination, their jeep collided head-on with a truck that was attempting to pass another vehicle in a cloud of dust. They both died instantly. As the most recent surviving member of the Silver City project (1958-1962), I was given the honorable though rather sorrowful task of putting the Hernon-Jones report "in shape" for publication. Fortunately the manuscript was already in good shape, so that the task has consisted of little more than minor reorganization and editing, and of preparation of the illustrations, abstract, and bibliography. The sections on wall-rock alteration had been left for Jones to complete in the light of his recently intensified interest in alteration geochemistry (25), and it is in these sections only that. the report may fall short, for they have been filled in from a 1958 manuscript by Jones on the ore deposits of the Santa Rita quadrangle that he intended to revise considerably. The shortcomings, however, are largely in the interpretation, not in the field data. As a brief but accurate summary of what was known about the geology of the Central mining district in 1965, this report stands as a fitting testimonial to the scientific dedication of two exceptional men.

Jan 1, 1968

By L. L. Seigle

Free energies, heats, and entropies of mixing of solid Fe-Au alloys have been measured by the galvanic cell method between 800° and 900°C. A positive deviation from Raoult's law and a large excess entropy of mixing were observed, both attributable to lattice distortion caused by the disparity in component atom sizes. Since the terminal solid solutortiontions are not regular, thermodynamic properties computed from the location of the mis-cibility gap do not agree well with measured quantities. The electromotive force data suggest some changes in the existing Fe-Au phase diagram. ALTHOUGH a considerable amount of information has been accumulated about the thermodynamic properties of metal solid solutions which exhibit negative deviation from Raoult's law, particularly those in which ordering occurs, relatively few experimental measurements have been made on solutions with positive deviation. This is due to the infrequency of broad homogeneous regions suitable for experimental measurement in solutions of this type, since any marked positive deviations from ideality lead to restricted solubility and the formation of miscibility gaps. Thermodynamic data reported in the literature for such systems have usually been calculated from the location of the miscibility gap boundaries under the assumption that the entropies of mixing are ideal, i.e., the terminal solutions are regular.' One of the few binary systems with both positive deviation and a wide homogeneous range in the solid is the Ni-Au system. A recent investigation of solid Ni-Au alloys' revealed that the entropies of mixing were much larger than ideal and consequently thermal data computed from the phase boundaries assuming regular solutions were seriously in error. Theoretical considerations put forward by Zener indicated that high entropy values should generally be associated with systems possessing a miscibility gap in the solid, when this is due to differences in the size of component atoms. These facts suggest that the regular solution assumption is a poor approximation for many solid solutions with positive deviation and that reliable thermodynamic data generally cannot be obtained by conventional methods from the location of miscibility gap boundaries. The Fe-Au system, Fig. 1, resembles the Ni-Au system in certain respects. The presence of a miscibility gap in the solid indicates a large positive deviation from ideality, but there is nevertheless an extensive single phase region suitable for experimental measurement. The following investigation of solid Fe-Au alloys was carried out in order to obtain additional data on the thermodynamic properties of metal solid solutions with positive deviation from Raoult's law and to further compare thermodynamic data computed from miscibility gap boundaries with those measured experimentally. Experimental Method The thermodynamic properties were derived from measurements of the potential developed between pure solid iron and Fe-Au alloys in a high temperature galvanic cell. The experimental apparatus and technique were the same as those used for the Ni-Au alloys and described in a previous report.' Cell electrodes were 1/16 in. diam rods swaged from chill-cast ingots and annealed for one week at 850°C. The alloys were prepared by melting fine gold granules under argon with pure iron obtained from the National Research Co. The cell electrolyte was

Jan 1, 1957

By P. Somasundaran, D. W. Fuerstenau

This article presents the results of an analysis of grinding of 1:1 mixtures of 4x8-mesh quartz and limestone in laboratory ball and rod mills. From these experiments, the amount of energy consumed in grinding each component of the mixture was determined. In the ball mill, limestone consumes slightly more energy than quartz in the initial stages of grinding, but as the grinding proceeds quartz begins to consume a slightly greater fraction of the energy. The postulate that the fraction of energy consumed by any material in a ball mill is proportional to its volume fraction has been shown to be approximately true. On the other hand, in a rod mill energy consumption by quartz and limestone is equal only in the initial stages of grinding, with energy consumption by quartz greatly exceeding that by limestone as rod milling proceeds. Preferential energy consumption in tumbling mills has been discussed in a number of papers. For example, from an analysis of the kinetics of comminu- tion in ball mills, Arbiter and Bhrany' obtained rate equations based on the postulate that only coarse particles are ground, indicating that fine particles are protected from the action of the balls by coarser particles. In rod mills this protective action is much more pronounced than in ball mills. Recent studies on the rod milling of limestone-quartz mixtures have shown that this protective action causes the mineral with the lowest grindability (quartz in this instance) to consume the greater fraction of energy. 2 However, in the ball milling of mixtures it has been postulated that the consumption of energy by one of the constituents is determined by its volume fraction within the mill. 3 Possibly this hypothesis may be a simplification of the ball milling of mixtures since the protective action suggested by Arbiter and Bhrany may result in some preferential energy consumption by one of the constituents of a mixture. The objective of this study has been to determine preferential energy consumption in laboratory ball and rod mills by analyzing size distributions of each material in the products obtained from grinding 1:l mixtures of quartz and limestone. MATERIALS AND METHOD The procedure for carrying out the tests on wet grinding quartz-limestone mixtures has already been described.'r3 In the present investigation, 1:l mix-

Jan 1, 1963

By Oliver Bowles

THE most important non-metallic mineral industries from a tonnage standpoint are those that are allied with the construction industries and are engaged in handling sand and gravel, crushed stone, building stone, cement, lime and gypsum. The greatest problem facing a number of these industries at this time is over-production. They have experienced un- usual, and in some instances phenomenal, growth during recent years, stinlulated by extensive highway and building construction, but in some localities expansion of producing plants has far outstripped industrial needs. The cement industry is operating at about two- thirds capacity. Over-production tends toward price- cutting and unprofitable and interrupted operation, involving maintenance expenses for idle plants and disorganization of working forces. This condition has encouraged active efforts toward reducing production costs by the introduction of labor-saving equipment. Also, there is a tendency toward the location of manufacturing plants, wherever possible, near the centers of consumption rather than at points of production of raw materials. In order to reduce overhead expense, or for other reasons, many consolidations of companies into larger units have taken place. An economic study of conditions in these industries is highly desirable. The U. S. Bureau of Mines has taken one step forward in this direction in the issuance of Economic Paper 7, entitled "Economics of New Sand and Gravel Developments." Briefly, this report emphasizes the importance of making a thorough study of all the economic factors involved before undertaking new .enterprises.

Jan 1, 1930

By David B. Dill, Edgar R. Lea

The zinc deposits of the Balmat-Edwards Division of the St. Joseph Lead Company in northern New York State provide some 10 per cent of the domestic zinc produced annually within the United States. These complex ore deposits are contained within marbles of the Precambrian Grenville series, in a repetitive sequence of dolomites and silicated units. The Balmat ore bodies are localized at various intervals throughout some 1800 feet of the stratigraphic column on the northwest side of a band of gneiss that has continuity to the Edwards area, some 10 miles to the northeast. The Edwards ore bodies are located to the southeast of this gneiss. The marble formations are thought to have included repetitive intervals of marine sedimentation that provided mineralized source "beds" and were subsequently folded, flooded, and injected with melts at great depth and were sheared, recrystallized, and reconstituted. Detailed structural and stratigraphic studies throughout the northwestern Adirondacks, in the Balmat-Edwards district, and at each mine in particular indicate the close dependence of the ore deposits on the enveloping structure whether it be local, district-wide, or regional in scope. Primary folding has developed a northeast regional trend with northwest dips. Secondary folding has been developed by an almost horizontal northeast-southwest-oriented shear couple in the plane of the regional trend. The secondary folding has produced crossfolds that intersect the regional northeast trend and plunge north to northwest at various angles. The ore bodies are found within certain stratigraphic horizons where repeated alternation of competent and incompetent beds encouraged unusually complex folding. Analysis of individual mine structures indicates that the location of each deposit is controlled by structural crossing of primary and secondary folding. The ore bodies, which are tabular, lenticular, or pod-like in form, have features that suggest parallelism to true bedding or modified flow banding, developed by northeast-southwest shearing stresses related to the development of the crossfolds. The ore deposits in general follow both structural and recrystallization trends within the wall rocks. Mobilization of the pre-metamorphic ore minerals is believed to have involved a combination of plastic flow under stress and solution of the sphalerite, minor galena, and pyrite. The ore fluids are thought to have been guided by secondary shearing and microbrecciation into structurally prepared areas where reprecipitation took place. The presumed premetamorphic mineralization now exhibits epigenetic high-temperature features related to late-stage metamorphism.

Jan 1, 1968

CAPTAIN JOHN H. BALLAMY John H. Ballamy, Captain on the Regimental Staff of the 103d Engineers, was killed near Fismes, on August 9, 1918. Captain Ballamy was born at Plymouth, Pa., in 1886 and graduated from the High School of that town in 1903. In the following year he began work as a coal miner, and at the same time began the study of mining engineering in the evening and any other spare time. He continued this diligent and energetic practice for many years. For sixteen years he continued in the employment of the Delaware, Lackawanna & Western Railroad Company's coal mining department, first as a practical miner, next as rodman on the survey corps, of which he soon became chief, then draftsman and mining engineer in the company's office. In January, 1916, he was promoted to the position of district engineer in charge of mining engineering work. He became a member of this Institute in September, 1917. CAPTAIN JOHN H BALLAMY. Captain Ballamy's military experience began at the same time as his engineering practice. He was a charter member of Company A, Engineers, N. G. P., which was organized ten years ago. He saw service on the Mexican border as First Lieutenant of this Company, and remained in that position until November, 1916. In July, 1917, he was again called into service and was sent to Camp Hancock, Ga., with the 103d Regiment of Engineers. Before joining this regiment he attended a school for officers at Fort Sill, Okla., where he received special training in field fortifications. In December, 1917, he was commissioned Topographical Captain on the Regimental Staff, and in April, 1918, preceded his regiment by about six weeks to France, where he again attended an officers' training school. He rejoined his regiment on July 15, near Chateau Thierry and was killed near Fismes on August 9, 1918.

Jan 11, 1918

By Gerald C. Dohm

INTRODUCTION After a mining company has discovered a mineral deposit, the problem is then how to mine and process that deposit the best way. The principal problem facing managers or engineers who must decide on mine plant size, equipment selection, and long-range scheduling is how one can optimize a property not only in terms of efficiency but also as to project duration. Mine opti¬mization is dependent upon the interaction of con¬tributing parameters which leads to maximizing the net present value (NPV) Realistic mine planning is the key, to the analysis. The process is to be used when evaluating undeveloped properties or when a complete revamping of existing facilities is scheduled The proc¬ess is not intended for detailed mine design but rather for property evaluation and feasibility studies. The derivation of the various input parameters will only be discussed to the point where a meaningful correlation can be made with the overall analysis. The interrelationship of the parameters will be the central point because most company guidelines and financial analysts have their own standards when deriving the various inputs. Assume that the data is totally acceptable and pro¬vides at least the following categories of information and guidelines- (1) mineral and waste inventory; (2) geologic, hydrologic, and geotechnical criteria; (3) topographic layout including property boundaries; (4) metallurgical flowsheet, recovery and design criteria; (5) access, water, power, and environmental base-line study; and (6) financial constraints (minimum rate of return, payback period, etc).

Jan 1, 1979

By Carl F. Floe, Michael B. Bever

ACCELERATED by the demands of war, research and development work in nonferrous physical metallurgy has continued at a rapid pace during the past year. In particular, advances have been made in processing and fabrication, especially of the light alloys, and in the surface treatment of metals. Theoretical physical metallurgy, although less active, has not been neglected and the year has brought forth some -notable contributions to our understanding of the fundamental structure of metals and their behavior in service. Of course, much work that has been done cannot be publicly discussed because of wartime restrictions.

Jan 1, 1945

[Executive J. V. W. REYNDERS, Chairman WILLIAM H. BASSETT E. DEGOLYER I-I. C. BELLINGER RICHARD PETERS, JR. Finance GEORGE OTIS SMITH, Chairman H. A. GUESS F. JULIUS FOHS Admissions GEORGE D. BARRON, Chairman DAVID LEVINGER P. A. MOSMAN H. K. MASTERS J. A, SINGMASTER Alternates F. G. BREYER C. W. HAMILTON F. E. PIERCE]

Jan 1, 1928

Edward A. UehlinG, New York City (communication to the Secretary*):—Mr. Baker's paper is one that brings up a subject of great importance, and if full statistics could be collectecl of the number of furnace-linings ruined by reason of bad distribution by skip-hoists, it would be found an astonishing array. Unfortunately a universal remedy has not yet been found. The fact that Mr. Baker has apparently succeeded in overcoming the trouble at Sydney, is no guarantee that the same remedy applied at another plant, where very different or even slightly different conditions prevail, mould cure the trouble. That it requires but a slight continuous difference of penetrability in the column of the descending stock of one section, over another, to produce channeling, is clearly demonstrated by Mr. Baker's experiments, by which he reversed the channeling from front to rear instead of remedying the trouble. Every change in the physical make-up of the charge necessarily requires a specific adjustment; even supposing this feasible, the regular working of the furnace is by no means assured, because with the high pressures now customary, the tendency of the ascending gases to plow their way through in a direct course, prevails, and having once opened up a passage, they will persist and cause trouble. Homogeneous filling-, hard driving and regularity of working are incompatible. The higher the furnace, the greater the

Jan 1, 1905