Search Documents

A New Ingersoll-Rand Turbo Blower The Ingersoll-Rand Co. has added to its Turbo Compressors and Blowers a low-pressure machine t o handle volumes from 3,000 to 35,000 cu. ft. per minute at from 1-2 ½ lb. These are particularly adapted to such service as foundry cupola blowing, atomizing oil for oil burners, supplying blast to heating and annealing furnaces of various kinds, blowing air for water-gas generators, pneumatic conveying and ventilating. They are of the single stage, double flow type and are furnished either electric motor, steam turbine or water wheel driven.

Jan 6, 1916

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By Raymond F. Gray, Victor J. Hoffman, Richard J. Bagan, Harold L. McKinley

The first indication of tungsten in the Bishop area was the discovery of scheelite concentrations in a gold placer operation in the ( since named) Tungsten Hills in 1913. After early intermittent production, the deposits of the district were slowly discovered and developed. The Pine Creek mine, located in 1916 and under the direction of Union Carbide Corporation since 1935, became the principal producer in the district. By the end of 1965, the total production of the district had reached 3,450,932 units of WO3, 17,071,242 pounds of molybdenum, and 19,599,110 pounds of copper. The topography of the district is characterized by its extreme relief, ranging in elevation from 13,986 feet to about 4400 feet in the Mount Tom quadrangle. The present topography is the result of the uplift and erosion of the Sierra Nevada and the great subsidence of the Owens Valley with its related deposition and volcanism. The general structure of the pre-Tertiary rocks consists of a series of tightly-folded metasedimentary and metavolcanic rock remnants surrounded by exposed plutons ranging in composition from hornblende gabbro to alaskite. The metasedimentary rocks consist of low- to intermediate-grade metamorphic equivalents of fine-grained sediments deposited during the Paleozoic era in a miogeosynclinal environment. Later volcanics were deposited in a eugeosyncline. The ore bodies in the Bishop district consist of scheelite-bearing tactite formed by the pyrometasomatic replacement* of calcareous sediments along the contact with an acidic granitic intrusive. A number of the metasedimentary remnants have had tungsten deposited along their edges.

Jan 1, 1968

By William H. Waggaman

CURTAILMENT of the mineral industry as a whole undoubtedly will follow world peace, but the output of certain minerals should pursue a course well above the average on any curve of probable output projected beyond the trends exhibited through 1939. Without speculating on industrial conditions in the pending recomversion period, demand for fluorspar should be greater than before the war because of these factors, introduced by or resulting directly from military necessity: (1) Discovery and development of new deposits. (2) Improved technology in benefication. (3) New and expanded uses for fluorspar and its derivatives. The steel industry has been and continues to be the greatest consumer of fluorspar, and it wag largely to meet the wartime needs for steel that the domestic fluorspar industry has been expanded so greatly. Not only were the search for and development of new deposits of this mineral considered esstinal but the marginal nature of some of the,c- domestic deposits made it necessary to improve mineral dressinc and processing techniques to utilize them

Jan 1, 1945

By AIME AIME

UNTIL recently, practically all geophysical prospecting in Australia was conducted by government departments, either by the Aerial, Geological and Geophysical Survey of Northern Australia or the New South Wales Department of Mines. At present, in addition, the Shell company is carrying out an extensive geophysical campaign in South West Queensland. The Northern Australia Survey has now been in operation for over six years, its work being carried out principally in the northern and central parts of Australia over an area of about a million square miles. At present this Survey is being brought to a conclusion but it appears certain that the geophysical section will be transferred to a Commonwealth Government department on a permanent basis. At present the officers of the Geophysical Section are preparing or have issued some 150 reports on their field work and also a special technical report on the geophysical practice of the Survey.

Jan 1, 1942

Joseph W. RichaRds, South Bethlehem, Pa. (communication to the Secretary*): The hold experiment of Mr. James Gayley in drying the blast used in the Isabella furnace has attracted the attention of the whole metallurgical world, and has given rise to a wide discussion of the reasons for its great success. Mr. Gayley and the capitalists who backed him in his work deserve congratulations on the success of the venture, not only because it succeeded, but because they have been rewarded far beyond the maximum that could be expected from theory or probability. To state the case in its simplest terms, all that could have been predicted was: (1) that the removal of the moisture from the blaet would result in the saving of the heat required for its decomposition, representing from 3 to 5 per cent. of the heat-value of the coke used; hence about that quantity of fuel might be saved; (2) that the furnace would be somewhat more independent of variations in the weather; (3) that the campaign would be a little hotter; and (4) that the speed of the blowing-eugines would be decreased, at least in amount proportionate to the reduction in temperature of the air led to them. I do not think anyone anticipated a much larger output per day. The results actually attained were: (1) the furnace made an increase of 24.86 per cent. in the output of pig-iron per day; (2) it consumed 19.6 per cent. less coke per ton of pig-iron made; (3) the blowing-engines were run 15.8 per cent. slower; and (4) the saving in power made up for the power required to run the refrigerating-plant. In addition, the blast was hotter; the waste-gases cooler, because of their smaller volume; and there was a greater proportion of carbon dioxide to carbon

Jan 1, 1906

By R. G. Fleck, W. R. Webb

Iron ore mining in the Adirondack region of northern New York dates back to the Revolutionary War. It is recorded that Benedict Arnold in his campaigns in the Lake Champlain area during the American Revolution utilized the local ores to produce armament and cannon balls. Through the efforts of early pioneers, the iron mining industry in northern New York gained impetus so that in the 1880's mines in the area accounted for nearly one fourth of the iron ore produced in the United States. Both magnetite and red hematite ores were mined during this period. With the discovery of the Lake Superior ores, the iron ore industry in New York started to decline and remained relatively unimportant until 1938. Modern day methods of mining and beneficiating sufficiently high tonnages of low-grade ores to justify the large expenditures for plant and equipment prompted a resurgence in northern New York mining. During the past several years, the production of iron ore from the Adirondack magnetites has greatly increased, and production which amounted to .6%, of the United States total during the 1918-1928 period (Mining and Metallurgy, November 1943) has been increased to 2.85% of the total in 1948. Today, Republic Steel is mining in the Port Henry-Mineville and Lyon Mountain areas; the

Jan 4, 1950

[A Aalseth, Earl P. (M 51) Geol, Amerada Petr. Corp., Box 1498, Billings, Mont. Abadie, Henry G. (M 43) Asst to Supvr of Oper, Long Beach Oil Dev. Co., 255 S. Santa Clara, Long Beach 7, Calif. Abbe, T. Waldo (A 56) Ass't Dist Oper Supt, Sun Oil Co., Beaumont, Tex. Abbott, J. L. (M 56) Partner, Pritchard & Abbott, 501, Century Bldg, Fort Worth, Tex. Abbott, Richard H. (J 51) Owner, Abbott & Howard, 422 W. Hermosa, San Antonio, Tex. Abbott, Seth J., Jr. (M 51) Tekoil Corp., .2;A6 Mercantile Nat'l. Bank. Dallas, Tex. Abbott,. William G. (M 50) Div Mgr, Rice Eng. & Op. Inc., Box 1142, Hobbs, N. M. Abderhalden, R. R. (J,59) Box 100, Carmi, Ill. Abel, Malcolm D., Gen Mgr, Bakke Oil Co., Midland, Tex. Abel, Raymond L. (M 28) Prof of Chem Engr, Univ. of Pittsburgh, Pittsburgh 13, Pa. Abel, Wayne K. (M 57) 1513 Patton Drive, Odessa, Tex.]

Jan 1, 1961

By B. H. Caudle, L. G. Loncarie

Pilot flooding is one method of evaluating a proposed secondary recovery project. However, the amount and rate of oil recovery from an unconfined pilot area is not usually the same as from an equal area in a large-scale flood. This is true because fluids are free to move across the boundary of a pilot area. The result is that some of the oil produced in a pilot flood may come from outside the designated area and some of the displaced oil may leave the pilot area completely. This paper presents the results of fluid-flow model studies on a five-spot pilot flood. Mobility ratios between 0.1 and to have been studied. The effects of changing the ratio of injection to withdrawal rates are shown. INTRODUCTION A small-scale field test, or pilot flood, is an accepted method for evaluating the applicability of a secondary recovery operation and the economic potential of that operation for a reservoir. The pilot flood is carried on in the same manner, with the same injected materials and at the same pressures as would be used were the secondary recovery program to be expanded to a larger area of the field or to the entire field. If the reservoir fluid and reservoir rock properties are the same in the pilot area as in the rest of the reservoir, the production, injection and other pertinent data associated with the pilot test will represent and measure what should be expected from a full-scale development of this secondary recovery program. There is one major exception which, unfortunately, has been overlooked by many and which has been awaiting quantitative definition. This is the sweep-out pattern the reservoir engineer must use in interpreting the pilot flood and in extrapolating it to the full-scale development. The sweep-out area in a pilot flood is not contained within the five-spot pattern. Further, there is oil flow into and/or out of the five-spot during a pilot test. Thus, production data from pilots must be interpreted with this different flow system and sweep pattern in mind. We have studied the sweep-out pattern that will exist for some conditions of operation of pilot flooding a single five-spot (four injection wells and one producer). In our study, reported here, we have assumed that the reservoir is relatively homogeneous and of uniform thickness in the pilot area. The results of this study en-able the engineer to predict the recovery, injection requirements and project life for a full-scale operation from the pilot flooding data. The effects of various injection to withdrawal-rate ratios and mobility ratios in a relatively gas-free (10 per cent pore volume or less) system are shown. Experimental Method The technique used in this study was the same as that for the X-ray shadowgraph studies of sweep-out pattern efficiencies.' The model of the pilot and surrounding area was made from a uniform packing of round-grain sand consolidated with an epoxy resin. Fig. 1 shows the relation between the model and the pilot area. Only one-eighth of the pilot area had to be represented in the model because we assumed equal injec-

By Walter F. Bradley

CLOSE to 300 members and guests were registered at the Regional Meeting of the Institute in San Francisco. Oct. 3-6, and many other mining men were present at some of the sessions, but failed to register. Headquarters were at the Palace Hotel. Technical papers for the Metals Session were sponsored by the San Francisco Section, whereas the program for the Industrial Minerals Session was arranged by the Southern California Section. Walter W. Bradley, Chairman of the San Francisco Section, opened the General and Metals Session, introducing President Buehler, who gave a hearty welcome to those present. Clyde M. Eye, of the. Benguet Consolidated Mining Co., presented the first paper, entitled "The Economic and Strategic Value of Philippine Metals to the United States." In closing, he urged. that this country retain and control the Philippines because their large

Jan 1, 1935

By E. T. Turkdogan, P. Grieveson, J. F. Beisler

Jan 1, 1963

By Jack L. Taylor

As expected from similar crystal structures and favorable atomic size factors, titanium, vanadium, and molybdenum are completely soluble in one another above the transformation temperature of titanium. The fl phase parameters of the continuous solid solution are shown graphically. Limiting compositions for retained fl phase have been determined. VANADIUM and molybdenum both have body-centered-cubic structures at all temperatures and, from the atomic diameter comparison factor, 3.9 pct, would be expected to form a complete series of solid solutions. The existence of complete solubility has been confirmed by work' at the Jet Propulsion Laboratory. Furthermore, vanadium and molybdenum have favorable atomic size factors to form complete binary solid solutions with the B phase, high temperature form of titanium, which also has body-centered-cubic structure. Pietro-kowsky and Duwez' and Hansen et al." have established the existence of the complete series of solutions in these binary systems. It would be logical, therefore, to expect that p-titanium, vanadium, and molybdenum would be completely soluble in one

Jan 1, 1957

By D. L. H. Forbes

(New York Meeting, February, 1912.) Introduction.. THE application of the cyanide process to complex sulphide ores for the extraction of their bold and silver is no longer a novelty, but, as an example showing modern tendencies in this direction, the following description of the new milling process at the Lucky-Tiger mine is offered: The extraordinary richness of the ore in the upper workings of this mine made any thought of milling in its early hays seen unnecessary. Its location in an almost inaccessible part of the rugged mountains just south of the Arizona boundary-line, and 60 miles from the town of Douglas, made the expense of bringing in machinery and supplies a very serious consideration. But, after the property had been shipping high-grade ore on mule-back for a few years, there remained in the mine a considerable tonnage of vein-matter that was too low in value to ship, but which it was thought could be milled near the mine at a profit. The first milling-experiment consisted in the installation of Nissen stamps in conjunction with concentrating-tables and Frue vanners, but, as the ore from the upper workings contained most of its silver in the form of cerargyrite, this type of mill was not successful. The proximity of the mine to the great copper-concentrating mills of Cananea and Moctezuma naturally made the influence of copper-milling, ideas felt in the company's next installation. At considerable expense a stage-crushing concentrating-mill, with a capacity of 100 tons per day, was built. This mill was modeled along the lines of the most approved practice in copper-concentrators at that time, the main idea being that crushing by stages in rolls was necessary in order to prevent losses from ?sliming." Largely owing to the fact that, when the mill

Aug 1, 1912

By AIME AIME

A REQUEST for information as to the details of activities of the Engineering Council was made by the Joint Conference Committee for the benefit of the new American Engineering Council. , This request was complied with, and the scheduled reply so succinctly sets forth the activities of the old Council as well as the scope of possible activities of ,the new Council, about whose efforts there has been much discussion, .that it' is given herewith in full, except the 'budget which is summarized.

Jan 1, 1920

By W. A. Hockings, D. W. Fuerstenau, A. L. Mular

This paper briefly describes a simple air pycno-meter and its use for rapid determination of the composition of mixtures of solid particles. Research on such problems as the pelletizing of solids, the mixing of solid particles, and the comminution of mixtures can be simplified by means of this analytical tool. THEORY OF OPERATION Liquid pycnometers1 are commonly employed to measure volumes. These devices are time consuming and sometimes give inconsistent results. The liquid used in the pycnometer may have an undesired influence on the material to be measured; moreover, complete displacement of air by the liquid is seldom

Jan 1, 1963

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, pro- [ ] duced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. [ ] The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. , I). Above the sand rock an overburden of Joachim limestone appears, which, thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes, where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OT THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By William E. Ford, Edward Salisbury Dana

1. Normal Class (25) Barite Type 2. Hemimorphic Class (26) Calamine Type 3. Sphenoidal Class (27) Epsomite Type Mathematical Relations of the Orthorhombic System Crystallographic Axes. - The orthmhombic system includes all the forms which are referred to three axes at right angles to each other, all of different lengths. 296 Any one of the three axes may be taken as the vertical axis, c. Of the two horizontal axes the longer is always taken as the b or macro-axis * and when orientated is parallel to the observer. The a or brachy-axis is the shorter of the two horizontal axes and is perpendicular to the observer. The length of the b axis is taken as unity and the lengths of the other axes are expressed in terms of it. The axial ratio for barite, for instance, is a : b : c = 0'815 : 10 : 131. Fig. 296 shows the crystallographic axes for barite.

Jan 1, 1922

By M. K. Foster

Ten horizontal retort zinc blocks of a modified Hegeler design are in operation at Nueva Rosita, Coahuila, Mexico, and produce approximately 170 t of spelter daily, or 62 000 t/year. A block consists of two furnaces of 448 retorts each, making 8960 retorts as the plant complement. Each furnace block is fired with natural gas and air maintaining the combustion mixture in the furnace always slightly reducing. No attempt to recover energy through waste heat boilers is made. The spelter moves to market by rail and truck either in palletized bundles weighing approximately 1060 kg, as loose slabs weighing 26.5 kg each, or as 1088 kg ingots. At present 46% of the metal is exported and 54% is consumed domestically in Mexico. The present day trend toward equalized or alloyed spelter, as well as special shaped castings results in sales of 35% of the entire plant's production. Sulfuric acid is also produced by the Contact Process using vanadium pentoxide as the catalyst. The plant is basically a Monsanto contact system, producing approximately 68 t of 100% sulfuric acid daily. Both 98.5% sulfuric acid and 20% oleum are available. All of the acid made is consumed in Mexico. Shipments are made in 26,900 dm3 tank cars.

Jan 1, 1970

By Marius R. Campbell

Does mine-sampling show the commercial value of a coal, and if so, how should it be done? This question is often asked, but seldom answered. During the past summer, while engaged in securing coal for the Government coal-testing plant at St. Louis, I had an excellent opportunity to obtain information on this subject, and the results seem to furnish an answer to the questions propounded above. Sampling for the Geological Survey Coal-Testing Plant. In organizing the work of the testing-plant, it was decided that coal in car-load lots only would be accepted for testing, also that this coal should be loaded under the immediate supervision of a representative of the plant, so as to be certain that the car-load sample would be representative. As an additional check on the work, two mine-samples were to be collected from each mine visited, and these samples, as well as the sam¬ple from the car when it was received at the testing-plant, were to be carefully analyzed at the chemical laboratory, which was established in connection with the plant and operated under the direction of Prof. N. W. Lord, of the Ohio State University, Columbus, Ohio. Mine-Sanmhling:-Mine-samples were collected with great care by me and my assistants, Messrs. J. Shober Burrows, John W. Groves and Frank W. De Wolf. The dominant idea in the regulations which were adopted for mine-sampling was that it should be done in such a manner that the sample would have the same composition as the commercial output of the mine. .

Sep 1, 1905

By Ernst M. Cohn

The demonstrations of the "Silent Sentry" by Union Carbide Corp. in 1957 and of a special tractor-plow by Allis-Chalmers in 1959 ushered in the technology era of fuel cells. The idea for direct conversion of chemical to electrical energy, first published in 1801 by Davy in England and Ritter in Germany, has been kept alive by a few people through 150 years: Grove built the first hydrogen-oxygen fuel cell in 1839; Mond and Langer made electrolyte contributions around 1890 that are still used today; Baur worked on coal-based cells from 1900; Bacon started his work in the '30's, which resulted in the first multi-kilowatt unit in the '50's; Davtyan studied molten-salt electrolytes in the '40's, followed by Ketelaar in the '50's; and Justi developed highly active electrodes in the '50's, to name only some of the pioneers. Despite the tremendous increase in research and development of fuel cells, these direct energy converters are still in their infancy. They will find their functional application in space, where power density must be maximized and product water utilized. These early systems will provide valuable experience in system engineering and reliability.

Jan 9, 1964